Search Documents

By Pierre Mousset-Jones, Felipe Calizaya

This paper summarizes the current research trends in the ventilation design for the construction of very long tunnels, and presents the results of leakage flow measurements in three auxiliary ventilation systems. The study includes an estimation of an important design parameter, namely, the leakage path resistance, and a discussion of its effects on the overall efficiency of a ventilation system. A sample problem is used to illustrate the calculations.

Jan 1, 1997

By James Veri, Andrew H. Stern, Gerald N. Torbert

When mining coal, the occurrence of high methane liberation rates can often overwhelm the existing ventilation capabilities of the working place and result in elevated levels of methane gas. These “gas-off/stand-by condition" events often limit the production of the section and increase the potential opportunity for the occurrence of an ignition. This paper investigates the potential effectiveness of using a continuous miner equipped with an integral dust scrubber which was modified to provide high flow rates to reduce these events during active coal mining. Work was undertaken to quantify various adaptations of the mining system, by simulating site parameters in the controlled environment of an instrumented "full-scale" test facility. Monitoring (in real-time) of velocities and gas concentrations at many fixed points was also undertaken in an attempt to learn the effective limits of the system at high release volumes of gas.

Jan 1, 1997

By M. T. Ityokumbul

Flotation columns and their variations are increasingly replacing conventional cells in mineral-processing circuits. While the operational characteristics of columns differ from those of conventional cells, the same scale-up methodologies are being employed. This practice may be attributed to a poor understanding of the factors that control throughput. The use of tall flotation columns is frequently justified because of the need for an increased particle residence time. However, it is shown that longer particle residence times alone do not translate into increased recoveries. In this paper, throughput data from several industrial flotation-column installations is presented. Also, an attempt is made at using dimensional analysis to provide a scale-up methodology for the factors controlling column throughput.

Jan 1, 1997

By C. A. Rawlins

INTRODUCTION Radcont is a program designed by the author of this paper for the industry to use as an instrument for radiation contamination evaluation and ventilation planning system. Radiation in mines are associated with the mining of gold and gold bearing minerals, as uranium and thorium is incorporated in the mining of these minerals. Radiation contamination in South African mines is not a new concept as it was investigated by the Chamber of Mines in the early 1960's and found not to be hazardous at the time. Since some of our mines export scrap metal to customers abroad, it came to light (1991) that some of the scrap metal was radioactive. The authority that oversees the nuclear aspects in South Africa is the Council for Nuclear Safety (CNS). They investigated these matters and found that the mines needed further information regarding radioactive material and the handling of these contaminated materials. As the various mines were licensed (with various conditions incorporated) thereafter, the mines had to do their own investigations as to what extent their properties (Surface and underground) were radioactively contaminated. Some mines were found to be highly contaminated over the years of operation and controlling conditions were installed and measures installed to reduce the contamination levels. One of the conditions when issuing a licence by the Council for Nuclear Safety (CNS), is that a screening survey be carried out to determine the radiation exposure levels and corrective action to be taken if necessary. These surveys must be done by a person trained in the required procedures for such a survey. The person must also measure the risk correctly and assess the results properly. In such a survey, the internal and external exposure levels must be determined to assess the total exposure of persons working in those conditions and take appropriate action if necessary. When doing such a survey, hundreds and more likely, thou- sands of data points are recorded. In order to assess the data recorded, various integrated and difficult calculations need to be made, and takes up enormous amounts of time. (This excludes the interpretation of the results ) The following explanation of the program shows the different parts of such a survey assessment calculations to be done. The paper details the program layout and the different sub- sections within the primary program. It must be stated that the program, as with any other program, is as accurate as the data inserted into the data base. The program and details thereof are given under the following headings: 1. TOTAL EFFECTIVE DOSAGE WITH REGARDS TO: • GME required gravimetric results obtained (mg/m3) • Thick layer or total contamination measured (Bq/m2) • Dry condition surveys with dust loads taken as a Standard l0mg/m3 • Wet conditions survey with dust loads taken as l mg/m3 • Airborne long lived alpha and beta activities as determined by analysis in Bg/m3 • LTD (Thermoluminescent Dosimeter). Results as obtained from the SABS (South African Buro of Standards) are recorded in this section for each month of the year for each individual worker. An average dose is then determined at the end of the year. • Bucket measurements as recorded. • Smear samples (Loose contamination). As determined by Electra or by analysis • Occupational factors for Metallurgical and Engineering occupations in and around the Metallurgical facilities of your mine. • All underground dosage determination and calculations. (Radon and Thoron) 2. INFORMATION REQUIRED WHEN PROGRAM IS INITIALISED: As the program is started, it opens up on the contents page. Here there are various options to choose from, but one is cautioned as a beginner in operating the program, not to perform any tasks before carefully reading these instructions. Firstly, one must go to the 'Information required" pushbutton. Press this button. The information required page is shown where the cursor can be moved to the block where one can enter the specific mines name. To enter a mines name, put the cursor in the block provided and just insert the mines name with the normal keyboard keys and press the enter button on the computer keyboard. To enter the other information required such as Alpha and Beta instrument efficiency, ALI (Annual limit of intake) and probe area, one can either press the 'Data required" button for a dialog box information or enter it manually by just putting the cursor in the block provided and entering as did above. In order to insert all the required information for the pro- gram to calculate the information required, one must proceed further by entering the area names surveyed in the spaces provided. There are 20 spaces to enter 20 different areas surveyed. One must further also provide the amount of days worked in each area (i.8. 250) in the block provided. The de- fault is 250 days. There are also standard information given in the information data page such as breathing rate (1,2 m31h), 8 hours worked per day, 5 days per week and 50 weeks per

Jan 1, 1997

By D. W. Park

Longwall mining is considered the most efficient underground coal mining technique in terms of coal extraction ratio, production rate, and safety standards. Due to the increasing demand for higher coal production, wider panel and faster face movement have become the recent trends. Thus, longwall mining can create unexpected threats such as roof falls, excessive face convergence, shield damage and numerous maintenance problems causing sudden interruption of coal production and serious safety hazards. A recent study at the University of Alabama is dedicated to develop LoSCoMS (Longwall Strata Control and Maintenance System) which integrates real-time shield monitoring, data presentation, analysis, forecasting, and warning modules. The main objectives of this system is to provide the stability and maintenance information, at every minute, such as high load, low setting pressure, leg leakage, etc., analysis of various mining and geological parameters to determine past and present roof characteristics and forecasting of loading patterns for the following mining cycles, next periodic weighting, etc. Using this unique system, mine operating personnel are well aware of past, present and future roof loading patterns at the longwall face, and thus, proper safety measures can be taken ahead of time.

Jan 1, 1997

By Daniel H. Stevenson

Safety and health are fundamental values at Barrick Goldstrike. An effective safety and health program protects employees, controls costs and increases productivity. Barrick Goldstrike believes that all occupational injuries and illnesses can be prevented and that safety must be the responsibility of every employee on the property. Safety and health must be thoroughly integrated with the company's efforts to maximize production at the lowest reasonable cost. The goals of safety and production are not mutually exclusive. They must work together to achieve safe production. Barrick Goldstrike began to mine the Betze deposit in 1987. From 1987 to 1992, Barrick employed a traditional safety system using safety specialists on each crew. These specialists were responsible for ensuring that the work areas were safe and that employees were properly protected and trained in safe work procedures. As the work force increased, it became apparent that this system was not the most effective method of ensuring safe production. In 1992, Barrick Goldstrike implemented a loss control program. It was modeled after the International Loss Control Institutes's (ILCI) International Mine Safety Rating System. This program was based on the philosophy that safety is a management responsibility. It can be managed in the same manner that production and cost issues are managed. Under the loss control system, safety needs are identified and evaluated. Programs with performance standards are developed and implemented and the activities and results are regularly monitored. Between 1992 and 1996, Barrick Goldstrike worked at developing and improving its safety management systems. These efforts had a positive return. The incident rates began to decline as these improved systems were implemented. Studies were undertaken in early 1996 to evaluate the effectiveness of the safety and loss control programs in reducing accidents. The studies showed a strong correlation between the implementation of the loss control programs and the resulting reduction in all accidents. Studies in the process division revealed that Barrick had experienced reductions in personal injury accidents from the projected number that could have been expected had no changes been instituted. These reductions ranged from 39% in 1993 to 59% in 1995. These reductions from the projected rates held true for all types of accidents; personal injury, property damage and Mine Safety and Health Administration (MSHA) reportable.

Jan 1, 1997

By Jaroslav Vicek, Alois Adamus

In the Czech Republic nitrogen was first used for the fight against the mine fire in 1949 (Hajek,1969). In the years 1949¬1996 the consumption of nitrogen in the Ostrava-Karvina Coal Basin /OKB/ reached more than 220 mil. m-3. The main source of nitrogen in the OKB is a central pipeline now. Gas nitrogen is used for the prevention of spontaneous combustion in gobs of longwall faces. The nitrogen infusion technology (Froger,1985), often called "franca technology", has been applied in the Czech coal mines since 1982. The aspects of the nitrogen infusion technol¬ogy can be theoretically solved by the calculation of mixing two gas streams in the filtration space. Longwall faces are parts of the ventilation network of the coal mine. The intake airflow of the longwall face is divided into the airflow passing through the face and a part of air losses passing through the gob. Air leakages through the gob and nitrogen in¬jected into the gob mix there. There is the main problem to solve air leakages in the gob. Usually, the principles of the gob aerody¬namics were used by many authors (Glusberg,1988;Voracek, 1994; Sulkowski,1993; Michailov, 1995; Dziurzynski, 1995; Kolarczyk, 1995; Saghafi, 1995; Sedlaty, 1993) that are applied to our case as well.

Jan 1, 1997

By M. P. Neira

In-situ leaching of copper from chalcocite relies on ferric iron concentration in the lixiviant being reduced to ferrous. To re-establish the ferric concentration in solution, ferrous must be re-oxidized. This reaction is slow under normal chemical conditions but it is catalyzed by Thiobacillus ferrooxidans bacteria. BHP Copper's Miami In-situ unit developed a bio-reactor as a method of oxidizing ferrous to ferric. The effects on oxidation of temperature, CO2? oxygen, and air injection flowrate were defined. This paper summarizes the results of ferrous bio-oxidation using plastic column packing and oxide ores as bio-reactors and the leaching results of the bio-reacted lixiviant on chalcocite ores.

Jan 1, 1997

By Janusz Cygankiewicz, Marian Branny, Józef Wactawik

The paper presents mathematical model of concealed fire. We consider a porous medium (goaf, coal fissures) through which air flows. The set of equations is constituted by transient, two dimensional mass, momentum and energy balance equations with sources describing oxygen loss and heat generation caused by coal oxidation. Paper presents several examples illustrating the phenomenon of spontaneous heating in goaf areas behind longwall faces.

Jan 1, 1997

By Joseph Fernandez, Luminita Calin

INTRODUCTION The Tunnel and Reservoir Plan (TARP), commonly known as the Deep Tunnel Project, is the daring and unique concept developed by the Metropolitan Water Reclamation District of Greater Chicago (MWRDGC) as a two-phase solution to the problem of waterway pollution and basement flooding due to sewer system backups created by the combined sewer over-flows (CSOs). Phase I, primarily for pollution control, includes the tunnels, shafts, connecting sewers and structures. These Phase I facilities intercept, during wet weather events, the CSOs within the MWRDGC TARP service area. The tunnels and shafts provide temporary storage of the CSOs for subsequent treatment at Water Reclamation Plants (WRP) before discharging into waterways. Ultimately, upon completion of Phase II, the tunnels, located from 45 m(150 ft) to 100 m (330 ft) below ground, will convey the CSOs to reservoirs for storage until WRP capacity is available. Phase II, which includes the reservoirs, pumping facilities, additional tunnels and shafts, has been planned to serve a dual purpose. The reservoirs provide storage of excess flows during wet weather events, those beyond the WRP capacity. Following the wet weather events, the stored flows can be conveyed, at controlled rates, to the WRPs for full treatment. These excess flows previously would have resulted in both overflows into the waterways and eventually backups in the local sewer systems. The storage capacity of the reservoirs also will promote the full utilization of the conveyance capacity of the tunnels and shafts, which in turn results in optimizing the conveyance capacity of the existing sewer systems. Therefore pollution control is further enhanced by allowing for capture of a greater volume of CSOs and greatly minimizing backups in the local sewer systems. The TARP project consists of four systems: O’Hare, Mainstream, Des Plaines, and Calumet, covering a total area of 971 km2 (375 mi2) and serving the City of Chicago and 51neighboring communities as shown in Figure1. With only two contracts left before completion of the Phase I tunnels, the 12.7km (7.9mi) Torrence Avenue leg, to be awarded in 1997, and the 12.4km (7.7mi) Little Calumet leg unfunded as of yet, both part of the Calumet System, the pollution control phase of the project is now 86% complete (Table 1).

Jan 1, 1997

By J. J. K. Daemen, C. Fairhurst

Two aspects of tunnel support design are considered, and for both particular attention is paid to the influence of rock failure around the tunnel on the loads developed on the supports. 1) In general it has not been possible to extend analytical methods for the study of rock failure around tunnels to three dimensions. As a consequence it was not possible to calculate either the influence of the face or the actual sequence of support loading as the face advanced. The finite element method made this extension possible. A simplified analysis of the influence of the face and of the sequence of support installation has been made. The influence of the original stress field and of the rock behaviour on the length of tunnel which can be left unsupported (related to the stand-up time) is shown. The degree to which a 2-dimensional analysis can be used to approximate the final support load is shown to be dependent upon the post-failure behaviour of the rock. 2) Tunnel support design requires a knowledge of the forces and of the -rock displacements which cause stressing and deformation of the support system. A 2-dimensional model incorporating a detailed representation of several support systems, of the rock behaviour in the broken zone and of the interaction between rock and support is given. The model allows the calculation of the stress distribution in the support. The significance of the relative stiffness of support and rock on the stresses developed in the support is shown.

Jan 1, 1997

By D. M. Conner

An innovative patented process has been developed to convert high volume wastes--fly ash from coal-fired power plants, municipal solid waste (MSW) ash from incineration, solids from waste water treatment and paper mill sludge into a high value and environmentally benign product in the form of a lightweight aggregate. Lightweight Aggregate is widely used in the building construction industry in the United States, Europe and some Asian countries. This paper will present the development of the process, the process itself and details on the first commercial scale plant. The commercial plant is owned and operated by Wisconsin Electric Power (WEPCO).

Jan 1, 1997

By William S. Eaton

Managing a mine or mineral processing operation in today's environment presents many unique challenges to mining companies. In recent years, headlines around the world have publicized major incidents such as those associated with the Marcopper Mine in the Philippines, the cyanide release in Guyana from the Omai gold mine and numerous other mishaps associated with mining. These notable upsets were due to engineered system failures, either during normal operations or as a result of uncontrollable events. There fore, many mining firms are attempting to assess their overall risks and establish some priority for expenditure of limited operational and environmental budgets. Failure of an engineered component can have dire operational consequences that affect profitability until repair or replacement can be completed. In addition, there may be significant environmental consequences associated with the engineered system failure. This, too, may affect profitability for an extended time or even the viability of an operation. An engineered risk assessment (ERA) can support a mining company's efforts to cost effectively manage environmental risks associated with the operation of its facilities. The ERA approach also provides information about the current condition of engineered systems. This ERA approach provides a systematic review of the risks of an engineered system failure and the possible associated environmental consequences at mining company facilities. This approach has been successfully applied to many industries and types of engineered systems (Barneich et al, 1996; Whitman, 1984; Power and Tomkins, 1974; Keeney, Nair, and Kulkarni, 1979). This approach evaluates all mining and mineral processing facilities located at a single site and compares them with similar facilities located at multiple mine sites. The ERA approach has been applied to a mining, milling, smelting, leaching and refining operations. These assessments can be part of a comprehensive environmental program to aid in the recognition and cost effective management of the potential environmental risks associated with the operation of facilities. ERA results support plan-

Jan 1, 1997

By V. Rastogi

Surfactant-based bactericides are able to control acid formation in sulfidic materials such as pyrite and sulfidic ores, thereby helping to abate acid rock drainage. Bactericides are used in the following two ways: as periodic or continuous spray treatments for the prevention of acidification of material actively handled and moved and in controlled-release form for reclamation. Site-specific bactericide treatments are designed for active sites and reclamation. Results from two active coal refuse sites show that acid production can be reduced by 88% or more. Results from reclaimed sites show that bactericide treatment can be more effective than the addition of alkaline materials such as limestone and can reduce acid production from 3,500 to <30 ppm. The controlled-release-pellets treatment outlasts the life of the pellets, as shown by a study of a site now 10 years old A single treatment sets up a change in site microbiology to replace acid-producing Thiobacillus ferrooxidans bacteria with heterotrophic bacteria and creates a stable site without the need for further treatments. A secondary beneficial effect of bactericides is on revegetation, and biomass from treated areas is almost 10 times that from areas not treated with bactericide. Depending on the application, bactericide treatment can be cost effective upfront and certainly long-term, compared to the perpetual water treatment that could be required, even after productive use of the site is completed

Jan 1, 1997

By W. M. Hart, Q. H. Shen, J. S. Chen, S. S. Peng

The automatic data-acquisition systems that are now available can continuously monitor and record changes in leg pressure and changes in advancing ram stroke in every shield. These systems can record shearer position at any moment during a mining operation. The data obtained can be used to improve production and maintenance management and can be used to provide better roof control at the longwall face. Research now being conducted jointly by West Virginia University and Cyprus Amax Coal Co. is aimed at developing a longwall-management system (LMS) for mine operators. The LMS software package, which works in the Microsoft Windows NT environment, performs data interpretation and analysis, production management, maintenance management and ground-control management for longwall mining.

Jan 1, 1997

By D. G. Krige

Discussion by D.G. Krige I read the paper "The jackknife approach" with interest. There appears to be a widespread misunderstanding of the kriging variance as a measure of the error variance of the kriged grade estimate of an ore block. Virtually all mineral deposits display skew frequency distributions and are subject to the well-known proportional effect. Thus, it is usual to find in an ore body, when subdivided a really into subpopulations, that the variances of the grades (or the total sills of the variograms) for the subpopulations will be correlated with the corresponding mean grades (usually linearly with the squares of the mean grades). Thus, the variogram will be station. When this feature is evident, the relative variograms for the subpopulations (i.e., with variogram values divided by the relevant mean squared) will be similar, or they could even be accepted at an averaged model for the whole ore body with stationarity. Using this approach, the kriging variance will reflect the relative error variance that is to be multiplied by the kriged block grade estimate squared to yield the usual kriging variance for purposes of confidential limits. The objection that the kriging variance does not take into account the local grades used for a block valuation then falls away. In the example given by the authors, the global mean grade is not recorded. But the global variance, taken at the value of the total sill, is 0.005, whereas the variance of the 11 values used in the example is 0.000152. The two variances differ by a factor of nearly six. If the relative variogram approach is applicable in this case, the need for a jackknife technique will fall away. Also note that, for skew distributions, the confidence limits for ore-block estimates will be skew as well, and symmetrical normal limits will not apply. RepIy by G.S. Adisoma and M.G. Hester There are a few interesting ways to utilize the block-by-block kriging variance that the authors have encountered. One of them is to classify a particular block into a proven-probable reserve or a possible-resource category, using a somewhat subjectively determined kriging variance value. Here, the kriging variance still represents the drilling density, i.e., data configuration more than the data values. Professor Krige mentions another ingenious approach through the use of relative variograms. This will yield a block kriging variance that takes into account local (block) grade, as he correctly points out, for purposes of confidence limits. However, we are more interested in quantifying the uncertainties associated with grade estimation in a much larger scale than a block. e.g., for a mining phase or the minable reserve. The jackknife, through the block kriging shortcut, provides a simple solution to obtain a single estimation variance for a general shape. The authors&apos; main reference discusses different ways to handle skewed distributions typical in mineral resource estimation, e.g., the weighted jackknife approach or data transformation. Also, as with any technique, we can always improve our estimate by subdividing into smaller populations that are geologically and statistically separate domains. As we have mentioned; the jackknife is but a tool in our collection of tools to solve estimation problems. The jackknife&apos;s appeals are its simplicity and versatility. It is handy when no other solution is available, or when the available solution is not practical. It is used with other methods, not to replace them altogether. ?

Jan 1, 1997

By David J. Leeds

Increased interest in the utilization of the underground environment for water conveyance tunnels, vehicular tunnels, room and pillar type storage chambers, and military installations has focused attention on the possible effects of seismic activity on the stability of these types of structures. Earthquake experience has generally been related to the seismic stability on the surface of the earth. To establish aseismic design criteria, we attempt to predict the seismic exposure of a given site, both in terms of the spectrum of motion to which the structure must react favorably, and the recurrence rate of that motion. Experience gained from studying the effects of the Plowshare underground nuclear tests on existing tunnels and mines, coupled with the experience of the behavior of tunnels and mines in earthquake regions, provides us with an insight to predict the possible effects of earthquakes on underground openings and to establish design criteria. The type of damage ranges from minor fracturing and movements along pre-existing joints or faults through deformation of openings to collapse. The methods used to establish the seismic design criteria for an underground opening require modification of surface criteria to account for the difference in both amplitude and spectra underground. An aseismic evaluation should be performed on all important projects in areas exposed to possible earthquake motion. To perform this evaluation, information is required pertaining to the geometry and properties of structure and ground. Dynamic as well as static properties are required. A prediction of performance can be derived by exposing a model of the site, expressed in terms of its properties and geometry, to a design earthquake.

Jan 1, 1997

By John C. Cook

In reasonably dry rock, long-wave radar can theoretically explore to distances approaching 75 meters (250 ft). High-resolution radar reflections have already been demonstrated through 13 m of hard limestone, through 9 to 18 m of coal in place and through 225 m of rock salt, using only low-power experimental radar equipment. Radar reflections have been received through the rock from rough pillar walls, from faults, and from a slim, uncased, vertical drill hole. In three years of intermittent experimentation, the feasibility of rapid radar exploration of large volumes of rock, with portable equipment, in deep, wet workings has been demonstrated. With future, improved equipment the theoretical working range, of the order of 75m, is expected to be attained in most hard rocks. THE TECHNIQUE Fig. 1 illustrates an early "monocycle" radar system (1) set up in a coal mine. This radar equipment is entirely different from that employed for detecting distant objects through the atmosphere. However, the basic principle is the same: a pulse of electromagnetic energy is radiated by the transmitter, a portion is reflected by some "target" object embedded in the surrounding medium and some of this energy is collected by the receiving antenna. In the receiver, the pulse is amplified, is "stretched out in time" by a sampling process, and is displayed on the screen of a cathode-ray oscilloscope. It may also be recorded on paper or magnetic tape. Fig. 2 illustrates a

Jan 1, 1997

By K. Kim, H. Gao

A site-characterization strategy formulated for the probabilistic assessment of rock mass properties is presented. The strategy, which takes into account the variability of rock properties and the stochastic nature of the rock-failure process, entails determining probability distributions of rock properties by utilizing extreme value statistics and Monte Carlo simulation. Laboratory and, field test data are analyzed and presented to illustrate the methodology. The results indicate that the distributive characteristics of rock mass can be estimated by using this proposed method. The results of the analysis can be incorporated into the design of underground structures. Then, the relative uncertainties of the failure probability of the structures can be assessed.

Jan 1, 1997

High pressure grinding rolls have found widespread acceptance for cement processing, and are now making their debut in the metalliferous minerals industry. Significant energy and wear material savings appear achievable in many applications. This paper re- views the technical literature on this important, emerging technology.

Jan 1, 1997