Search Documents

By Robert H. Marshall

The application of simulation to production planning at a large, complex open-pit mining operation proved to be challenging and enlightening. The mine is divided into two separate pits and several dump areas which are served by the same truck fleet. The operating system consisted of shovels of two different sizes, wheel loaders, and a fleet of three different truck types moving material from seven source locations to ten dumping sites. The interconnecting haulroad network included many common segments. There were operating constraints unique to the system, such as: traffic rules; manpower limitations; shovel, material-type, and destination priorities and production limitations; and a unique, non-centralized dispatching method for truck distribution. The truck distribution was further constrained by the matching of trucks to shovels, loaders, and destinations by truck type. The gathering and transformation of input data as well as the evaluation of results and validation of the model were also challenging. Despite a high level of sophistication in production reporting, some input data were neither readily available nor backed by field observation. As a result, many innovative techniques had to be used to develop realistic input data and to validate the simulation results. Nevertheless, this case study definitely proved the feasibility of applying computer simulation techniques to short and long range mine planning and budgeting at a large, complex mining operation.

Jan 1, 1982

By Catherine T. Aimone

A computerized cost model has been developed to simulate the technical and economic effects of strip mine blasting in the vicinity of structures. Current surface mining regulations restrict the allowable level of production blasting as a function of this distance. Blast design modifications,' therefore must be employed when blasting in the vicinity of homes to ensure compliance with federal and state regulations specifying limits to the seismic effects generated from a blast. The blasting level allowed. is computed by the charge weight of explosives per delay from the following scaled distance formula: [ ] where W is the charge weight per delay, in kilograms (pounds), D is the distance factor corresponding to the regulatory limit of peak particle velocity to which a structure may be subjected to. Current regulations specify 2.54 cm (1.0 in.) per second corresponding to a SD factor of 27 (60) (Federal Register, 1977).

Jan 1, 1982

By Shinzaburo Kato

In 1977 Kawasaki Steel Corporation (KSC) built No. 6 BF (Blast Furnace) with an inner volume of 4 500m3 as part of our program to produce 8.5 million tons of crude steel a year at Chiba Works. As the primary raw material to be used in No. 6 BF, we decided to use sintered ore, because we were confident in the obvious advantages of our technology developed by that time on sintering and BF operation using sintered ore. At Chiba Works, however, we had no space for the construction of a sinter plant, so we decided to build it abroad. Sintered ore is easily crushed and degradated. Producing sintered ore at a point far away from the blast furnace and transporting it across the ocean was the world's first attempt. To successfully realize it, we conducted a series of fundamental surveys and studies with special stress on the real aspects of degradation of sintered ore caused by long-distance transportation and handling and the ways and means to prevent the degradation. As a result, we decided to build a plant on the Mindanao of the Philippines.

Jan 1, 1982

By Thomas A. Wilson

Mountain Pass, California is located 96 km southwest of Las Vegas, Nevada, and has an exposed surface orebody within view of Interstate Highway 15. Mineral prospecting in this region dates back to about 1860 followed by the discovery and subsequent mining (1870-1895) of silver bearing veins on the north slope of nearby Clark Mountain. In contrast to the four lane divided interstate highway of today, all supplies needed for mining during this early history were transported by wagons from San Bernardino which is 320 km west. Many small lead mines were active in the area during 1917-20, and a small gold mine operated in 1941-42 within 100 m of the orebody presently being worked. In 1949 two prospectors searching for uranium with a Geiger counter discovered a radioactive vein outcrop at Mountain Pass. Further investigation revealed the presence of a large amount of a light-brown, heavy mineral to a depth of about 2 m. A sample of this unidentified mineral was submitted to the Boulder City, Nevada, U.S. Bureau of Mines where a spectroscope examination shoved high level rare earth oxides, carbon dioxide, and fluorine. These results indicated the mineral was bastnasite.

Jan 1, 1982

By Richard L. Bullock, Bruce Kennedy

Vince Lombardi once said, "Practice doesn't make perfect, perfect practice makes perfect." When it comes to building a mine that will operate at the optimum level for the set of geologic conditions from which it was developed, Lombardi's remark might be paraphrased to describe the problem: planning won't guarantee the best possible mine operation unless it is the best possible mine planning. Any sacrifice in the best possible mine planning introduces the risk that the end results may not reach the optimum mine operation desired. This section addresses many of the factors to be considered in the initial phase of mine planning. These factors have the determining influence on the mining method, the size of the operation, the size of the mine openings, the mine productivity, the mine cost, and, eventually, the economic parameters used to determine whether or not the mineral reserve even should be developed. A little-known fact, even within the metal-mining community, is that room-and-pillar mining accounts for most of the underground mining in the united States. According to a 1973 study on noncoal mining (Anon., 1974), more than 76% of the producing mines [of over 1089 t/d (1200 stpd) capacity] produced approximately 70 000 000 t (77,000,000 st) or 60% of the nation's underground tonnage of material by room-and-pillar mining. That same year, 96.8% of the nation's under- ground coal mines produced 262 950 000 t (289,911,000 st) of coal extracted from room-and-pillar mines (Anon., 1976). Thus, nearly 333 000 000 t (367,000,000 st) of the United States' raw material is produced from mines using some form of the room-and-pillar mining system. Because approximately 90% of all mining in the United States is done by some variation of room-and- pillar mining, it is appropriate to give special emphasis to the effects of the various elements of mine planning on room-and-pillar mining. The relationship of these elements to other mining methods will become apparent as the elements are described in later sections herein. TECHNICAL INFORMATION NEEDED FOR PRELIMINARY MINE PLANNING Assuming that the reserve to be mined has been delineated with diamond-drill holes, the items listed in the following paragraphs need to be established with respect to mine planning for the mineralized material. Geologic and Mineralogic Information The geologic and mineralogic information needed includes the following: 1) The size (length, width, and thickness) of the areas to be mined within the overall area to be considered, including multiple areas, zones, or seams. 2) The dip or plunge of each mineralized zone, area, or seam, noting the maximum depth to be mined. 3) The continuity or discontinuity within each of the mineralized zones. 4) Any swelling or narrowing of each mineralized zone. 5) The sharpness between the grades of mineralized zones within the material considered economically minable. 6) The sharpness between the ore and waste cutoff, including whether this cutoff can be determined by observation or must be determined by assay or some special tool; whether this cutoff also serves as a natural parting resulting in little or no dilution, or whether the break between ore and waste must be induced entirely by the mining method; and whether or not the mineralized zone beyond (above or below) the existing cutoff represents submarginal economic value that may be- come economical at a later time. *7) The distribution of various valuable minerals making up each of the minable areas. 8) The distribution of the various deleterious minerals that may be harmful in processing the valuable mineral. 9) Whether or not the identified valuable minerals are interlocked with other fine-grained mineral or waste material. 10) The presence of alteration zones in both the mineralized and the waste zones. Structural Information (Physical and Chemical) The needed structural information includes the following: * 1 ) The depth of cover. 2) A detailed description of the cover including: the type of cover; * the structural features in relation to the mineralized zone; * the structural features in relation to the proposed mine development; and * the presence of and information about water, gas, or oil that may be encountered. 3) The structure of the host rock (back, floor, hanging wall, footwall, etc.), including: * the type of rock; * the approximate strength or range of strengths; * any noted weakening structures; * any noted zones of inherent high stress; noted zones of alteration; the porosity and permeability; * the presence of any swelling- clay or shale interbedding; the rock quality designation (RQD) throughout the various zones in and around all of the mineralized area to be mined out; the temperature of the zones proposed for mining; and the acid generating nature of the host rock. 4) The structure of the mineralized material, including all of the factors in item 3 plus: * the tendency of the mineral to change character after being broken, i.e., oxidizing, degenerating to all fines, recompacting into a solid mass, becoming fluid, etc.; * the siliceous content of the ore; the fibrous content of the ore; and the acid generating nature of the ore. Economic Information The needed economic information includes: *1) The tons of the mineral reserve at various

Jan 1, 1982

By Dominc C. Torre

INTRODUCTION Rapidly increasing capacities of equipment used to load and handle material at the face require improved haulage equipment and better methods of transporting the mined materials or "muck" to the shaft or slope and out of the mine to the processing plant on the surface. Increasingly, those transportation demands are being satisfied with underground belt conveyors. Such con¬veyors provide the most readily available, most efficient, and most reliable method of carrying materials in a continuous and rapid flow from the face loading equip¬ment to the surface plant. Almost universally, belt con¬veyors are used in coal mines and those nonmetallic and metallic mines operating in relatively flat bedded deposits. Belt conveyors are available in a wide range of capacities, mainly limited by belt width, belt speed, and weight of the material to be transported. They can be used on the level, on grades, on the surface, or under¬ground. They provide a rapid and constant flow of material, transporting the material as quickly as it is mined. Length of belt conveyors is almost unlimited. Where the haulage distance exceeds the practical capacity of a single conveyor unit, two or more conveyors can be used in series. Single conveyors more than 1.6 km (1.0 mile) long are common; multiple-unit conveyors in series operation are transporting materials over distances exceeding 16.1 km (10 miles). Depending upon mate¬rials being transported, job conditions, cost of the terrain being spanned, and alternative haulage methods avail¬able, conveyors can be conceivably economical for even greater distances. Table 1 lists maximum belt speeds recommended for most materials, relating belt speeds to belt widths. Table 2 lists capacities of typical conveyors of various widths and speeds, transporting commonly mined mate¬rials of various weights. ADVANTAGES OF CONVEYOR SYSTEMS For several years after their initial introduction, belt conveyors were available only with rigid side frames or a supporting structure of steel and concrete. That con¬struction limited underground applications, due to the cost and relative inconvenience of extending or retract¬ing the belt conveyor in the confined underground environment. However, during the last 20 years, wire-¬rope side-frame belt conveyors, as shown in Fig. 1, have become widely used in underground applications. Even wider use can be anticipated with their application to the fast movement of materials in surface mining operations. Advantages of the wire-rope side-frame belt con¬veyors were realized first in panel or section belt haulage in coal mines. Soon afterward, use of those conveyors was extended to gathering and main-line haulage. The mobility of the wire-rope side-frame conveyor is the principal reason for its success. The conveyor can be extended, retracted, dismantled, moved, and reassembled easily, even in relatively confined under¬ground spaces. The intermediate structure consists of rope support stands, wire-rope side frames, wire-rope tie-off stands, and the necessary carrying idlers and return idlers. An important and very attractive feature is the ability to suspend the conveyor from the roof in an underground mine, as shown in Fig. 2, leaving more room for improved housekeeping and allowing passage of face-service equipment, haulage vehicles, and other mining equipment. The conveyor's open construction allows quick and easy visual inspection of its com¬ponents for failures or malfunctions; it also facilitates checking and correcting conveyor-belt alignment. Other advantages contributing to the attractiveness and widespread application of wire-rope side-frame conveyors in main-line, slope, and surface installations include: lower capital costs, lower installation costs, lower maintenance costs, reduced impact on idlers and belting, reduced spillage and minimal cleanup, improved conformation to undulating terrain or mine bottoms, and the ability to span most obstacles without heavy structural support. CONVEYOR CLASSIFICATIONS Underground belt conveyors are classified normally according to their function. Generally, conveyors are classified into one of four main categories: 1) Panel or section conveyors normally receive the material to be transported directly from the face-haulage equipment. 2) Gathering conveyors are secondary haulage units that usually receive material from two or more panel conveyors. 3) Main-line conveyors transport all the material mined in the underground operations to the slope or shaft. Normally, they receive the material from two or more gathering conveyors. 4) Slope conveyors generally operate in tandem with the main-line conveyor, providing continuous Table 1. Maximum Belt Speeds Recommended for General Use Run-of-Mine Hard Ores and Belt Width, Coal and Earth, Primary Crushed mm (in.) m/s (fpm) Stone, m/s (fpm) 356(14) 1.52 (300) 1.52 (300) 406(16) 1.52 (300) 1.52 (300) 457(18) 2.03 (400) 1.78 (350) 508(20) 2.03 (400) 1.78 (350) 610(24) 2.54 (500) 2.29 (450) 660(26) 2.54 (500) 2.29 (450) 762(30) 3.05 (600) 2.79 (550) 914(36) 3.30 (650) 3.05 (600) 1067 (42) 3.56 (700) 3.05 (600) 1219 (48) 3.56 (700) 3.30 (650) 1372 (54) 3.56 (700) 3.30 (650) 1524 (60) 3.56 (700) 3.30 (650) 1676 (66) 4.06 (800) 3.81 (750) 1829 (72) 4.06 (800) 3.

Jan 1, 1982

By Fred N. Kissell

INTRODUCTION During the last few years, several new ventilation developments have attracted the interest of mining engi¬neers. Some of these developments are applicable pri¬marily to hard-rock mining, while others are more applicable to coal mining. STOPPINGS Parachute Stopping The parachute stopping is a new type of quick-erect stopping that is intended for temporary use in hard-rock mines (Kissell, Thimons, and Vinson, 1975). As shown in Fig. 1, the stopping is shaped very much like an ordinary parachute, with a canopy of impermeable fabric that is sewn to regularly spaced straps running to a common point. To erect the stopping, the straps are attached to a fixed anchor point such as a roof bolt, and the edge of the canopy is lifted into the moving air¬stream. The airstream pops the parachute canopy into place, and the differential air pressure across the stop¬ping holds it in place, forcing the fabric against the walls, roof, and floor of the mine opening. The principal advantage of the parachute stopping is that it requires only a few minutes to install, making it a great time-saver for emergency use or for day-to¬day changes in ventilation during the production cycle. However, the parachute stopping does require some minimum air velocity to lift it and some minimum differential pressure to hold it in place. For a fabric weighing 0.27 kg/ m2 (8.0 oz per sq yd), the minimum air velocity is about 0.5 m/s (100 fpm), and the mini¬mum differential pressure is about 0.05 kPa [0.2 in. water gage (WG) ]. There is always some air leakage around the stop¬ping, mainly depending upon the extent to which pipes or other obstructions encumber the airway and prevent good sealing. Leakage of a few cubic meters per second (a few thousand cubic feet per minute) can be expected, unless foam is used to improve the seal at the edges of the canopy. Quick-Fix Blowout Stopping The quick-fix blowout stopping is a variation of the parachute stopping (Thimons and Kissell, 1976), and it is used in the proximity of blasting operations. This type of stopping is designed to be blown out easily by the blast forces, and it may be reinstalled quickly and easily. The long high-strength straps of the parachute stopping are replaced by groups of short straps that tear easily. These straps are attached at six equally spaced locations around the perimeter of the canopy. To erect the stopping, one strap of each of the six groups is fastened to the mine wall, roof, and floor by using spads, by setting pins with a powder-actuated gun, or by tying the straps to some firm anchor point. Once the straps have been attached, the differential air pressure across the stopping, which must be at least 0.025 kPa (0.1 in. WG), forces the stopping perimeter against the mine walls, thus creating the air seal. It is the self-sealing feature of this stopping that makes it a significant time-saver. Only a few attachment points are needed; in many cases, four attachment points are sufficient, since the stopping naturally tends to form a seal with the airway surfaces. When nearby produc¬tion blasting exerts excessive forces on the stopping, one or more of the straps tears away from its attachment point, protecting the stronger canopy from damage. Damage-Resistant Brattice The damage-resistant brattice is a stopping that is designed for use in mines such as salt and limestone mines where the differential pressures are low and the roof is relatively flat. As shown in Fig. 2, the damage-resistant brattice consists of a series of brattice panels that are hung vertically and joined by Velcro® connections. When the brattice is subjected to strong blast forces, the Velcro® connection peels apart and allows the panels to open without incurring damage. The Velcro® connections can be resealed by hand within a matter of minutes. Such damage-resistant brattices have withstood the blast effects of 318 kg (700 lb) of ammonium nitrate-fuel oil (ANFO) explosive detonated as close as 91 m (300 ft) from the brattice. Ordinary brattice cloth is used for the panels, with a 51-mm (2-in.) wide strip of Velcro® hooks sewn along one edge of the length, and a 51-mm (2-in.) wide strip of Velcro® pile sewn along the other edge. Both the hooks and the pile are sewn onto the same side of the brattice cloth. The resulting Velcro® seal formed be¬tween adjacent panels is perpendicular to the brattice itself, and the leading edge of the seal can be directed either toward or away from the blast forces; the brattice works equally well in either case. To hang the brattice, panels of brattice cloth about 0.9 m (3 ft) longer than the height of the airway are cut from a 1.8-m (6-ft) wide roll. The additional 0.9 m (3 ft) of brattice cloth allows 0.3 m (1 ft) for attachment to the roof by means of a board, with 0.6 m (2 ft) for forming a good air seal at the floor. Each brattice panel is wrapped once or twice around a 51 X 102 mm (2 X 4 in.) or 25 X 76 mm (1 X 3 in.) mounting board that is 254 to 305 mm (10 to 12 in.) shorter than the width of the panel. For convenience in

Jan 1, 1982

By Staff

GENERAL DESCRIPTION The Lucky Friday mine is located in Mullan, Sho-¬shone County, Idaho. The mining method is horizontal slice cut-and-fill (with timbering for support or un¬timbered) using hydraulic sand. Cemented sand fill at a 1:17 ratio is used in sill pours and at a 1:7 ratio for the final 152 mm (6 in.) capping in successive stope floor pours. Annual production with 100% cut-and-fill mining is 167 829 t (185,000 st). The average depth of mining is 1296 m (4250 ft) and the average travel time to the stope is 45 min. GENERAL ORE BODY REQUIREMENTS AND LIMITATIONS Size The ore body is 396 to 488 m (1300 to 1600 ft) long on strike, 1421 m (4660 ft) on dip, with an average width of 2.3 m (7.5 ft). Dip varies from vertical to1.2 rad (70°) Ground Conditions, Ore Value, and Production Requirements The ore body contains quite strong argentiferous galena and quartz. The hanging wall and footwall are strongly sheared and fractured. Ore value is $211/t ($192/st).

Jan 1, 1982

By Hubert Erik Sherer

Determination of the best time to replace an aging unit of equipment is a recurring problem which is common to essentially all surface and underground mining operations. Virtually all mining equipment is subject to wear and the resulting deterioration that increases with equipment life. This mechanical deterioration results in lower availability and, thus, decreasing, production. Due to decreasing production and increasing repair costs, there is an optimum age at which the replacement of a given equipment unit with a new unit will result in the lowest cost per unit of production for the equipment operation in question (Figure 1). Determination of this optimum replacement age is further complicated by factors such as: possible overhaul alternatives, fleet replacement and expansion alternatives, remaining life of the mine, and technological improvements in the potential replacement or differences in the production capacities of these replacements. Determination of the optimum time to replace an equipment unit becomes more critical each successive year due to the rising capital costs of new equipment versus maintaining old equipment. An incorrect choice of the replacement age for an equipment unit can result in excessive costs to the mining operation. If a unit is replaced too early, the capital cost of the unit is not fully utilized; conversely, replacing a unit too late results in excessive maintenance costs and low production. The economic life of a piece of equipment is the equipment age that results in the lowest total discounted cost per unit of production for that piece of equipment, not considering the cost of future replacements. The economic life of a piece of equipment is usually shorter than the physical life, the maximum age at which a machine is capable of doing useful work. The optimum replacement age for a piece of mining equipment may vary from the economic life of that equipment due to the remaining life of the mine, fleet considerations, costs associated with potential replacement machines, and capital rationing constraints. For example, the equipment life of the current machine that may result in the lowest cost per unit of production might be 10 years; however, when the timing of the future replacement costs are entered into the calculation, a different life for the current machine might result in the lowest total cost per unit produced for the remaining life of the mine.

Jan 1, 1982

By Rex C. Bryan

An accurate and dependable ore reserve estimate is important to any mining company. It is also essential for development drilling and production planning to know about the distribution of the ore within the area to be mined. This paper will show that in the case of more variable deposits such as uranium, the use of geostatistics is superior to conventional techniques. Unlike conventional methods, geostatistics includes the importance of spatial orientation of measured variables. With the use of variograms in conjunction with kriging, a point or a block may be estimated along with its error of estimation. The existence of disequilibrium can create a severe problem in uranium 'ore reserve estimation, and mine and production planning. Disequilibrium can be simply defined as the ratio of chemical or assay values to gamma equivalent values calculated from the downhole geophysical gamma-ray logs. Various methods for adjusting for disequilibrium have been proposed. Most, however, have side stepped the consideration of disequilibrium itself being a regionalized phenomena; or its, relation to surrounding geology. This paper presents methods of incorporating both aspects. The East Dilts Pit at the Bear Creek Uranium Mine in Wyoming, has been used as a case study. Polygonal, triangular, and lognormal kriging and various disequilibrium adjusted methods, including multi-factor cokriging have been com- pared with the mining experience.

Jan 1, 1982

By James M. Griffin

It was not many years ago that people would have argued that a coal session did not belong at an International Mining Convention. Historically, steam coal has always been used domestically due to its natural geographic diversity and high transportation expense. Times have changed. With the help of Opec, steam coal has gone international. As opposed to metallurgical coal, whose trade routes have a long history, whose supply sources are more limited and whose market growth is seen by most to be relatively flat, steam coal export forecasts are calling for more than a doubling by 1990 and a quadrupling by the year 2000. Suddenly, one must be familiar with coal mining on a global basis in order to predict which regions will be able to fill these markets.

Jan 1, 1982

By John Jonkman

Two major changes occured during the last 5 years in the applications of computers. First, the cost of computer equipment decreased drastically in an era of high inflation. Second, technological breakthroughs in hardware and software have been applied successfully so that the average person can successfully utilize the computer without having to be a computer expert himself. The mining industry has recognized that computing technology has evolved to a point where it can be applied successfully to assist in improving productivity. Since equipment downtime is one of the major reasons for lost production, the Kennecott Minerals Company has developed a comprehensive maintenance information system which now assists the maintenance department in minimizing equipment downtimes. This paper discusses the primary features and functions of this system, the state-of-the-art technology that has been applied, and the benefits that resulted from using this system. Programs to support mobile equipment maintenance scheduling, which currently are under development, are reviewed and a summary of future applications is given.

Jan 1, 1982

By Kewal K. Kohli, Richard E. Thill, Syd S. Peng

The results of unpublished investigations into surface subsidence from coal mining in the Northern Appalachian Coalfield are summarized. These investigations were carried out by various coal companies and the State of Pennsylvania in the sixties and seventies. Subsidence data were collected and analyzed from 10 room-and-pillar panels in 5 mines in the Pittsburgh coal seam. Results show that angle of draw ranges from 26° to 33° and subsidence factor from 0.42 to 0.72; surface heating generally occurs beyond the edges of the panel, the amount and extent of which vary; waviness occurs in the subsidence profile if a substantial number of pillar stumps are left in irregular patterns; interpanel effect is significant; time-dependent subsidence exists, but varies for different panels; and surface slope does not seem to affect the amount of subsidence.

Jan 1, 1982

By Yvon H. Poirier

Carbon addition in the oxide pelletizing process is a big concern at the Sidbec-Normines pelletizing plant since 1976. Laboratory pot-grate testing carried out before the initial start-up of the Port-Cartier plant indicated that the nominal pelletizing grate capacity could be increased by fifteen percent with a suitable carbon addition. Also an improved induration cycle offered the possibility of a significant energy reduction within the process with no adverse effect on pellet quality. A one month plant scale program duplicated the lab test results and confirmed the anticipated cost saving by using these techniques. Since March '80, Sidbec-Normines use coke addition as a current operation. This paper reviews briefly earlier laboratory and in-plant test work carried out to investigate the effects of adding carbon materials to the Fire Lake hematite concentrate, and presents operation techniques and plant results of carbon addition in the Port-Cartier pellet plant.

Jan 1, 1982

By Edward S. Frohling

Va a ser discutida la información que se requiere para un estudio preliminar de viabilidad y la información adicional que se requiere para el estudio final de viabilidad de un nuevo depósito de mineral. El estudio preliminar de viabilidad se realiza con muy poca información y con un mínimo coste para el propietario. Sin embargo, el diseno del informe preliminar es similar al utilizado para el informe final. En este momento, se supone que el resultado del estudio preliminar es favorable y el propietario autoriza el estudio final de viabilidad a una compañía de ingeniería. Se describirá el tipo de organización para completar el estudio final de viabilidad. El informe final incluirá toda la información y datos relativos al nuevo depósito de mineral. La información presentada debe ser entendida lo mismo por el personal financiero que por el técnico.

Jan 1, 1982

By Kenneth P. Katen, Robert H. Trent

GENERAL DESCRIPTION Shortwall mining is one of the newest mining meth¬ods to be introduced into the world coal industry. The technique of shortwalling seems to have a number of origins, but it is generally agreed that it is an outgrowth of pillar-and-stall mining where timbering was employed as the primary means of roof support. In early opera¬tions the face was undercut by a shortwall cutter, hand¬bored, and blasted. The coal was loaded by hand or gathering arm loader. Australia, having experienced success with this method, advanced the technique through the use of mechanized roof supports in 1968. Although there were several attempts at shortwalling in the US, it was not until 1973 that Eastern Associated Coal Corp.'s Federal No. 1 mine successfully extracted a shortwall panel. Table 1 is a list of shortwall opera¬tions in the US as of April 1976. Shortwall mining is a method of mining in which a continuous miner cuts and loads from the short end of a rectangular pillar of coal while hydraulically powered self-advancing roof supports provide protective cover. Characteristics of a shortwall system include panel di¬mensions (Fig. 1) of 610 to 1219 m (2000 to 4000 ft) in length, face widths of 30 to 61 m (100 to 200 ft), straight-line ventilation, and production machinery, with the exception of roof supports, commonly used on con¬tinuous miner units. GENERAL REQUIREMENTS AND LIMITATIONS The justification for shortwalling is primarily eco¬nomic, i.e., increased production and recovery concur¬rent with savings in material and labor. The method also has a number of secondary benefits including the much needed progress it has stimulated in deep mine technology, the alternatives it presents to some of the problems resulting from the 1969 Coal Mine Health and Safety Act, and is perhaps a key to the solution of the enigmatic labor problems which plague the industry. The advantages of shortwall mining over continuous miner units include the following: a highly effective method of ventilation and dust control; a greater per¬centage of extraction (approximately 85%) ; fewer equipment moves, hence more efficient operating time; cost savings on materials such as roof bolts, rock dust, ventilation curtains, timbering materials, and the labor needed to supply, load, and transport these materials; a cyclical pattern of mining, each phase of which, i.e., development and retreat, lasts for approximately three months and appears to be psychologically motivating as well as highly productive; and improved safety. In addition to these positive aspects, a shortwall sys¬tem also has advantages over a longwall system, and these are listed as follows: the capital outlay for a shortwall system is one-third to one-fourth that for a longwall (1976 prices); the shortwall system utilizes equipment that is used on a continuous miner section, with the ex¬ception of the roof support system; there is a great deal of flexibility in areas with numerous gas wells and in areas where surface subsidence cannot be tolerated; the shortwall has reduced tailgate problems, since the tail¬gate entry serves as a return airway only; and the cyclical pattern of mining insures that the mining machinery pro¬duces coal even while the roof support system is being moved to another panel. There are several parameters which govern the se¬lection and use of a shortwall system. They are all of equal importance, and hence are not listed in any par¬ticular order. These are deposit size, seam height, seam inclination, roof and floor conditions, depth of over¬burden, subsidence and chain pillar extraction, man¬power, ventilation, and materials handling. Deposit Size Reserves available for shortwalling should be suffi¬cient for at least an eight to ten-year period, since this seems to be the effective life, without rebuilding, of a hydraulic roof support under average conditions. Of

Jan 1, 1982

By A. J. Sinclair

Los métodos de desmuestre para estudios de viabilidad dependen de las características geológicas del yacimiento que ha de ser evaluado. Se requiere un estudio geoestadístico preliminar, teniendo en cuenta los aspectos de autocorrelación de las variables sometidas a estudio, con objeto de que el plan de diseño de muestras pueda ser optimizado para producir las estimaciones de ley y tonelaje dentro de los límites de errores establecidos. En general, debe de tenderse a una distribución regular de muestras para ello, y longitudes regulares de las mis¬mas (a partir de los testigos o cortes, por ejemplo) son preferidas con objeto de facilitar los análisis estadísticos. Los planes de desmuestre son modificados y mejorados (bien técnica o económicamente) a medida que avanza el programa y es obtenida información adicional. Las muestras a granel para pruebas metalúrgicas pueden ser evaluadas en término de va¬riaciones señaladas por todas estas muestras en un depósito y la variabilidad de la ley dentro de las mismas. Una atención adecuada sobre estas fuentes de variabilidad asegurará una evaluación adecuada de los resultados de las pruebas piloto de las muestras a granel. Por otro la¬do, un estudio mineralógico general del yacimiento es un requerimiento importante, a veces ignorado, en una evaluación más general pero semicuantitativa de la representatividad de una muestra a granel; y, además, proporciona una información muy útil para optimizar el diseño de la planta.

Jan 1, 1982

By Wilbur I. Duvall

INTRODUCTION This chapter outlines some general principles and procedures that a rock mechanics engineer can use to arrive at a logical design for the size, shape, and spacings of underground openings in various types of com¬petent rock formations. Rock formations can be clas¬sified into six major categories which are useful for design purposes, provided the necessary input data are available regarding the geology of the site, the physical properties of the rock, the in-situ stress field in the rock, and the general geometry of the underground openings. The US Bureau of Mines (USBM) developed a rock classification system based upon these concepts and found it to be useful for design purposes (Obert, et al., 1960; Obert and Duvall, 1967). This classification sys¬tem is given in Table 1; however, an extra column has been added to the original classification to indicate the appropriate design techniques for each rock class. In this classification system, two main classes of rock are considered: competent rock and incompetent rock. Competent Rock Competent rock is any rock which, because of its mechanical and geological characteristics, is capable of sustaining underground openings without the aid of any structural support except that provided by unmined rock in the form of pillars and side walls, etc. Roof bolts and small random props which support only local loose rock are not considered structural supports. Competent rock is further subdivided into three ad¬ditional categories-massive, laminated, and jointed¬ which are defined as follows: Massive Rock: Massive rock is a rock formation where the spacing between mechanical defects such as joints, partings, or faults is equal to or greater than the critical dimensions of openings, or where the strength of the bond across these mechanical defects is com¬parable to the rock strength. Laminated Rock: Laminated rock is a rock forma¬tion divided by approximately parallel planes of weak¬ness into lamina whose thicknesses are small compared to critical dimensions of openings and where the bond between the lamina is weak compared to the rock strength. Elastic Rock-This is rock whose physical proper¬ties will permit the use of elastic theory to predict strains and displacements from applied stresses. Inelastic Rock-This is rock whose physical proper¬ties are such that strains and displacements are a strong function of time as well as applied stress. Incompetent Rock Incompetent rock is any rock which, because of its mechanical and geologic characteristics, is not capable of sustaining underground openings without the aid of additional structural support in the form of linings, steel sets, or systems of props. This classification system for rock depends not only on the mechanical and geologic characteristics of the rock but on the size of openings and their depth be¬low the surface. For example, many competent rocks at shallow depths for small stress fields could become inelastic rock at greater depths and larger stress fields, or competent massive rock for small openings could be¬come laminated or jointed rock for larger openings. Thus, to classify rock for design purposes requires a knowledge of the geologic properties of the rock mass, the physical properties of the rock, the general size of the openings to be mined, and the average range of the in-situ stress field to be encountered. To design underground openings and structures in rock, it is necessary to use criteria of failure for rock under various stress conditions, and to use safety factors to allow for differences between laboratory and in-situ strength properties of rock and to account for errors in¬troduced by the various assumptions made in the design process. Criteria of failure based on maximum stresses have been found to give reliable results in practice. Thus, it is assumed that rock will fail in tension when the tensile stress exceeds the tensile strength of the rock as determined by a standard modulus of rupture test on samples of rock core. If the tensile stresses in rock are small, then it is assumed that the rock will fail at a value of compressive stress equal to the compressive strength of the rock as determined by standard uniaxial compres¬sive strength tests on samples of rock core. These fail¬ure criteria, when used with appropriate safety factors, can be expressed as:

Jan 1, 1982

By A. M. Marabini

Flotation of rutile with N-benzoyl-N-phenyl-hydroxylamine (N-BPHA) has been investigated. Initially, floatability tests were performed in a Hallimond tube. The results indicated that rutile was floatable in the pH range from 2 to 4 at N-BPHA concentration between 2x10-3 M and 2x10-2 M. Selectivity against hematite was recognized when operating at pH values below 2. Following the hypothesis of the formation of a surface chelate between N-BPHA and titanium ion, this compound was precipitated from a solution of Ti(SO4) to which N-BPHA was added. I.R. spectrometry oft the rutile before and after treatment with N-BPHA solution confirmed the presence on the rutile surface of the same compound. The absorption isotherm and kinetics were determined by analyzing N-BPHA in solution with an U.V. technique. A hypothesis for the mechanism of adsorption of N-BPHA on rutile is suggested.

Jan 1, 1982

By K. J. Reid

A historical background of the development of automated material balance packages is presented including a summary of currently available packages and a description of the present work at the Mineral Resources Research Center of the University of Minnesota. A brief mathematical statement of the problem is given and solution techniques discussed. The problems and difficulties normally associated with material balances, both hand calculated and computer calculated are described. Several aspects of the available material balance packages as related to the "user/computer" interface are evaluated in detail. Elements of the material balance packages that affect the solutions are examined and the relative performance of the main packages on specialized problems presented. Finally, areas associated with automated material balances that require further work before computer packages can be widely used in industry are outlined.

Jan 1, 1982