Search Documents

By Dean Workman

Long extensible conveyor systems are an important option for efficient tunnel excavation where intermediate access is impractical. The conveyor system designed for the Pula Subbaiah Veligonda Tunnel #2 in Andhra Pradesh, India will eventually extend to 19.35km. The Ø10.0m water diversion tunnel will be excavated under India?s largest tiger sanctuary using a Robbins Double Shield TBM. Once extended, the conveyor will be one of the longest single-flight systems ever installed in India, and is expected to offer increased system availability over comparable systems using muck cars. This paper will examine the engineering challenges of long-flight extensible conveyor systems in the areas of belt selection, component design, and equipment location in confined assembly and launch areas

By M. A. Ackerson, R. E. Griffin, W. H. Pomroy

Two automated fire detection system configurations have been used successfully in underground mines: the pneumatic "tube bundle" approach and the electronic telemetry approach. The electronic telemetry approach is more widely used, owing to its greater speed, flexibility, and capacity to both monitor other underground conditions, and remotely control underground equipment. However, depending on specific mine conditions and layouts, pneumatic detection, or a combined pneumatic/telemetered system may offer significant advantages over the telemetered approach alone. This paper describes research by the U.S. Bureau of Mines to design and in- mine test a rapid response pneumatic fire detection system tailored to the unique requirements of multilevel metal mines. The relative merits of pneumatic detection are discussed in the context of typical multilevel mine layouts and environments. A Bureau developed proto- type system is described with emphasis on design features which counter commonly perceived and/or experienced pneumatic detection system operating problems. Finally, the results of a 3-yr in-mine performance evaluation of the prototype hardware are discussed. Included are descriptions of system layout and coverage, response time, tube leakage, sample dilution, elimination of accumulated water from sample lines, and system maintenance and reliability.

Jan 1, 1989

By H. Do, R. Yoon

Mineral flotation is effective over a relatively narrow particle size range of approximately 10 to 100 µm. If the upper particle size limit can be increased, however, a run-of-mine ore may be coarse ground, and only the middlings are ground further to achieve required grades. This will result in significant energy savings and increased throughput. In this communication, methods of increasing the upper particle size limit will be discussed on the basis of a flotation model that can predict flotation from both hydrodynamic and surface chemical parameters. An example of increasing flotation recovery by control of a chemistry parameter is given.

Jan 1, 2007

By Peter F. Howard

The lower Middle Cambrian phosphorite deposits of the Georgina Basin shown in Figure 1 were found in the period 1966-1968 by three companies, namely, International Minerals and Chemical Corporation, Continental Oil Corporation and Broken Hill South Limited. Of these deposits the significant ones are Duchess, Sherrin Creek, D Tree, Lady Annie, Lady Jane, and Wonarah which together aggregate several billion tons reserves of phosphate. Due to the economic factors of freight costs to the coast and softening of the world market price for rock phosphate, none of them is in production, nor is any in the development stage. This paper reviews the historical background to the discovery of these deposits and then deals principally with the discovery of non-outcropping phosphorites in the Barkly Tablelands of Northern Territory by the interpretation of gamma radiation logs of abandoned water bores.

Jan 1, 1971

By S. Michael Feroz, Paul Gribbon, Jan Rosholt

Approximately six billion gallons of combined sewage are discharged annually into Willamette River and Columbia Slough through Portland’s combined sewer system. The Columbia Slough Consolidation Conduit (CSCC) is an important element of mandated Combined Sewer Overflow (CSO) abatement. It includes2,548m (8,361 ft.) of 3.7 m. (12 ft.) internal diameter tunnel. The CSCC alignment traverses the UP railroad, Columbia Boulevard and parallels an old sewer. Geologic conditions include river alluvium and fine to coarse-grained flood deposits containing cobbles and boulders. This paper describes design and construction of a tunnel in soft-ground, with shallow cover and close to an old concrete sewer.

Jan 1, 1999

By Yu. A. Polozov, V. A. Lagunov, O. Yu. Lushinkova, Yu. I. Svirskiy, Eh. Ya. Kipko, Roy A. Williams

5.1 TECHNOLOGY FOR INJECTING GROUT INTO BOREHOLES The grouting of fractured rock aquifers is carried out in separate stopes' whose size is determined by the hydro¬stratigraphy and the hydrogeologic properties of the rocks. The number of grouting stopes required depends on the number of intervals in the hydrogeological section. Each grouting stope can include one or several aquifers. Com¬bining several water-producing strata into one stope is pos¬sible only when the values of their permeability coefficients are very similar. In order to achieve efficiency, as many aquifers as possible are included in each stope. In practice, the length of a grouting stope in a borehole usually ranges within 10 to 40 m, but occasionally up to 100 m or more. When conducting grouting operations through boreholes drilled from the face of underground workings, the stope's size can be determined by the thick¬ness of each fractured zone (fault) or by the length of the hole if the entire rock is fractured. Injecting grout into separate intervals of fractured rock can be done from the bottom to the top with ascending stopes or from the top to the bottom with descending stopes. Injection from bottom to top is always preferred. Injection also can be accomplished in separate fractured permeable horizons in the section. The STG integrated grouting method is based on the use of packer and injection equipment and technological schemes that facilitate injection in highly isolated fractured aquifers. For this purpose STG has developed a standard series of packers. 5.1.1 INJECTING GROUT THROUGH BOREHOLES DRILLED FROM THE SURFACE Grout can be injected according to one of four techno¬logical schemes depending on the depth of the fractured aquifers, their hydrogeologic properties and the availability of grout injection equipment if the area is remote (Fig. 43). In the first and most preferred technological scheme (1), the grout is injected from the bottom up with ascending stopes. When this scheme is employed, grouting holes are drilled to the entire projected depth based on the field investigations injection tubes is installed above the top of the first hydrostratigraphic unit to be grouted. This scheme al¬lows the grout to be injected only into the permeable stra¬tum or strata isolated by the packer near the bottom of the hole; it precludes the need to clean or redrill the hole before injecting grout into the next overlying stope. This ascending stope scheme is preferred because of its simplicity and ef¬ficiency. It is used in most of the grouting of saturated fractured rock for the purpose of isolating aquifers while excavating deep mine shafts in the USSR. The second technological scheme (II in Fig. 43) injects the grout in sequence from top to bottom with descending stopes. Injection under this scheme is accomplished through the hermetically-sealed mouth of the hole. It is most advis¬able to grout with descending stopes in saturated fractured rock wherein the aquifers constitute thick networks of frac¬tures. Under these conditions it is practically impossible to drill a grout hole to the entire depth of the underground workings due to the large production rate of ground water. In conducting isolation operations with descending stopes, additional work (relative to ascending stopes) is necessary to drill out the grout in order to create and inject the next stope. As a result, the total amount of drilling required to drill out grout can even exceed the volume of drilling of original rock. Consequently it is advisable to use this inefficient scheme only for injecting grout into holes that contain prolific frac¬tured aquifers at depths less than 150 to 200 m. The third and fourth technological schemes (III and IV in Fig. 43) are used in the selective grouting of separate aquifers. For example, these methods would be applied when a grout hole is drilled to its entire depth, wherein grouting of the upper aquifers must be done first so that the sinking of the first shaft can begin prior to deeper grouting. The third technological scheme is used for the selective injection of grout into an aquifer with a thickness of up to 5 m. For this work the DAU-1-2 removable dual packer is installed. It is lowered into the borehole on an injection pipeline. For aquifers with thicknesses of more then 5 m, the selective injection of the grout is carried out according to the fourth technological scheme; a combination of the DAU-2 hydrodynamic plug and the DAU-1 packing device is used. In order to implement this injection scheme, the DAU-2 hydro-dynamic plug is installed at the bottom of the fractured aquifer and the DAU-1 packer is installed at the top of the aquifer.

Jan 1, 1993

By David R. Baughman, John C. Gathje, K. C. Oberg, Gary L. Simmons

Santa Fe Pacific Gold Corp. conducted pressure-oxidation pilot plant studies on refractory carbonaceous gold ores from the Twin Creeks Mine in Nevada. The tests were conducted at Hazen Research Inc., Golden, CO, during 1993 and 1994. Laboratory investigations using CIL cyanidation after batch pressure oxidation demonstrated gold recoveries of 90% to 95%. However, pilot plant testing showed that several of the same ore types responded very poorly, with gold extractions of only 45% to 75%. Plant testing was suspended for approximately four months while extensive research was conducted to determine why these ores responded poorly and to identify potential solutions. This paper describes the batch and pilot plant test results, the extensive research activities that eventually identified the cause of the gold recovery problem and the final semicontinuous and continuous pilot plant operations that confirmed possible solutions. Final pilot plant results showed gold recoveries that were consistently greater than 90%.

Jan 1, 1999

By A. Shah, L. W. Saperstein, M. C. Radomsky, D. L. Passmore

The development of microcomputer software that provides an analysis of pit-specific accident and production data for the mining industry is seen as a vital component in a total loss-control system. The Mine Injury Reporting System (MIRS) allows users to access accident and production data prepared by the Health and Safety Technology Center of the Mine Safety and Health Administration of the US Department of Labor for any particular state and to generate a simple, yet informative, report.

Jan 1, 1990

By Harry Elkin

Control of coal dust has long been an important aspect in the conventional mining of coal; the main reasons being from a health and disaster standpoint. With the advent, of mechanized longwall mining, the control of dust has required more attention due to the high extraction rate common to most longwall systems. The purpose of this paper will be to describe the dust abatement activities of the longwall operation at Sunnyside. Kaiser-Steel Corporation has three mires located at Sunnyside, Utah, with a total production averaging 6,800 tons of clean coal per day. Of this 6,800 tons, 71 % is mined with continuous miners, the remaining 29% coming from one longwall unit located in No. 3 Mine. Our first longwall panel was started in November, 1961. In October, 1966, we started mining our seventh panel. The present panel is located in the Upper Sunnyside Seam which averages five feet in thickness, but does get as low as 51 inches. The seam pitches 5.5% in this vicinity. The roof is generally good and is comprised of 10 inches of shale cap rocs overlain with sandy shale and sandstone. The floor is sandy shale and is quite undulating in nature. The present panel is 3,800 feet in length with a face of 670 feet. The major equipment employed on our longwall unit is a 125 H.F. Anderton Shearer-Loader, British Jeffrey Diamond armored conveyors and a Dowty self-advancing-roof support system. The Anderton Shearer in use on our longwall unit has a 60" diameter x 27" cutting drum. During the shearing cycle, it traverses the face at 20 feet per minute with a cutting rate of 7.5 tons/minute.

Jan 1, 1967

By G. J. Joy

Although rates of pneumoconiosis in coal miners have declined substantially in the United States since the passage of the Federal Coal Mine Health and Safety Act of 1969, new cases continue to occur, including cases of rapidly progressive disease. In contrast, Australia's underground coal mining industry has reported few new cases of pneumoconiosis for more than 20 years. Mortality from coal workers' pneumoconiosis in official health statistics and the prevalence of pneumoconiosis among miners screened in X-ray surveillance programs are also lower in Australia. The U.S. National Institute for Occupational Safety and Health (NIOSH) was requested by both industry and labor stakeholders to examine this issue, with the ultimate aim of reducing the rate of pneumoconiosis among U.S. coal miners. A number of factors, including coal dust exposure, silica exposure and coal rank were examined as potential contributors to the above noted differences. Comparison of coal rank data from each country did not illuminate the issue. Air sample data from the coal mining industries in both countries show that coal dust levels in Australian mines are somewhat higher than those reported in similar U.S. mines; however, quartz exposure for Australian miners is lower than for many U.S. miners. If quartz is contributing to the greater number of cases of pneumoconiosis in the United States, more effective dust control measures, as well as an independent exposure standard for respirable quartz in coal mining, should be implemented to reduce this potentially disabling condition.

Jan 1, 2012

Refractory gold concentrates often contain submicroscopic gold that is encapsulated within the crystal matrix of iron sulfide minerals, such as pyrite, pyrrhotite and arsenopyrite. To recover the gold, the host mineral must generally be broken down chemically by oxidative processes, such as roasting, pressure oxidation or bacterial leaching, which expose the gold for subsequent recovery by leaching in cyanide solution. The focus of attention in these pretreatment processes is usually the oxidation of the sulfides to elemental sulfur, sulfur dioxide gas or sulfate ions. Less attention is paid to the deportment of iron and the changes in its oxidation state, although this can have a profound effect on gold and silver liberation, as well as downstream operating costs. Iron sulfide minerals break down completely during pressure oxidation, and dissolve in the sulfuric acid solution that is gener-ated from oxidation of the sulfides. This dissolution liberates the tiny gold particles that were originally trapped in the sulfide crystals, and gold recovery during subsequent cyanidation is usually very high (>95%). Iron goes into solution in the oxidation process, initially as ferrous sulfate, but this compound is rapidly oxidized to ferric sulfate, which then hydrolyzes and reprecipitates. The form of the precipitate varies depending on the operating conditions in the autoclave and the presence of certain metal cations. When the acidity in the autoclave is quite low (<20 g/L H2SO4) and the temperature is high (>200°C), the formation of hematite is favored. When the acidity is high (>20 g/L H2SO4) and the temperature is relatively low (160 to 200°C), the formation of basic iron sulfate is favored. If the ore or the leach solution contains significant levels of certain cations (such as Na+, K+, NH4+, Ag+ or Pb2+) and the acidity is high (>20 g/L H2SO4), jarosite compounds are favored. Hematite is the desired iron product in the autoclave discharge, for both metallurgical and environmental reasons, but it is difficult to operate an autoclave under the conditions required for effective liberation of gold without converting some of the iron to basic iron sulfate and/or jarosite. These compounds fall into a category of iron compounds known generically as iron hydroxy sulfates, all of which can cause significant processing and environmental problems in the downstream gold process. This paper deals specifically with basic iron sulfate: the conditions under which it is formed in an autoclave, the problems that are caused by its presence in the feed to a cyanidation plant and possible remedial strategies that can be adopted, both in the autoclave and downstream.

Jan 1, 2010

By W. M. Luff

Introduction The Brunswick No. 12 mine is located about 27 km (17 miles) southwest of Bathurst, New Brunswick. The deposit is a stratiform massive sulfide deposit occurring in a series of sedimentary and volcanic rocks of the Tetagouche Group. These rocks are generally considered to be Ordovician in age. Ore reserves at Brunswick No. 12 are 104 Mt (115 million st) grading 3.72% lead (Pb), 9.01% zinc (Zn), 0.32% copper (Cu), and 97.9 g/t (2.8 oz per st) silver (Ag). Production in 1984 was 3.5 Mt (4 million st) at 3.57% Pb, 8.91% Zn, 0.32% Cu, and 100 g/t (2.9 oz per st) Ag. Total payable silver production that year was 211 t (6.8 million oz). This made Brunswick one of the largest silver producers in Canada. Bathurst-Newcastle area and Brunswick Mining Interest in the Bathurst area was aroused in 1897 when W. Hussey discovered an iron formation at Austin Brook, just south of Brunswick No. 6 deposit. This area, and the current No. 6 area, was explored from 1897 to 1907. Iron ore was mined at Austin Brook from 1907 to 1913 and from 1942 to 1943. Any occurrence of sulfides was overlooked until 1952. In 1952, M. J. Boylen Enterprises investigated the small sulfide body associated with the Austin Brook iron formation. Other electromagnetic anomalies associated with the iron formation were investigated. The No. 6 deposit was found late in 1952, when hole B12 intersected 97.5 m (320 ft) of massive sulfides. The No. 12 deposit, 10 km (6 miles) to the north, was found in 1953. More than 30 massive sulfide deposits have since been identified in the Bathrust area. In the 1950s, St. Joe Lead Co. did extensive test work on the No. 6 and No. 12 deposits, including shafts at No. 12, lateral development at No. 12, and testing at both deposits.

Jan 10, 1986

By Bob Snashall

Mines, miners and mining figured in the revolutionary birth of the USA. This occurred with a little help from General Washington&apos;s friends, the French. When the colonial minutemen confronted King George&apos;s "bloody lobsterbacks" at Concord, MA, in April 1775, the resulting "shot heard around the world" resounded in Versailles. France was sympathetic to the patriot&apos;s struggle. Before the Lafayettes shipped out, came French muskets and powder... but not many musket balls. The Continental Congress issued orders to get the colonial lead out for shot and shell. Colonial mining enterprises had been chiefly local affairs, cheaply supplying product to the surrounding communities. Since wood was accessible for fuel, coal had not been exploited.

Jan 1, 1990

By A. Khan

The effect of sulfur dioxide on collectorless and collector induced flotation of chalcopyrite was studied by cyclic voltammetry on a rotating disc electrode. Contact angle measurements were made to determine the effect of sulfur dioxide concentration and electrochemical treatment. The benefits of sulfur dioxide in enhancing the selectivity of separating chalcopyrite from complex sulfide ores are discussed.

Jan 1, 1996

By G. S. Brierley, R. D. Drake, J. E. Kelley, J. C. Kellogg

This case study embodies the problems of an underground project under current contracting practices. It will provide a realistic framework for a structured examination of the anatomy of a major complex underground project. Just as it will illustrate the frustrations of the parties to an underground contract, it will also provide a means to examine potential opportunities to provide a better way to develop underground space. Urban Transit Authority (UTA) had planned to expand their heavy rail underground transit system through an extension to an existing line. UTA lacked sufficient funding to guarantee the construction and operation of this planned extension. Venture Partner Associates (VPA) in conjunction with four major department stores entered into an agreement to create a major underground space for a commercial/recreational facility. The concept was to locate the facility adjacent to a planned station and beneath existing aboveground office facilities. This group was known as Commercial Development Corporation (CDC). UTA had reached an agreement with UMTA to provide 20 percent of the line and station costs. UTA then entered into an agreement with CDC to provide the needed additional funding for the station work in return for locating the station adjacent to the planned underground commercial/recreational complex. The agreement called for CDC to contribute 20 percent to the station cost to a maximum of $25 million plus a one percent contribution from commercial/recreational revenues for operating costs.

Jan 1, 1989

By John M. Dale

Now that the price of sulfur has reached unexpected high levels, it is little wonder that sulfur from surface ores is again receiving attention. In most instances, it is advantageous for an ore to be at or near the surface. However, it is a distinct disadvantage for sulfur ore to be close to the surface because it precludes the use of the Frasch process. The Frasch process depends on the presence of at least 180 m of uniform overburden to allow pressure injection of superheated water into the sulfur-bearing formation to melt the sulfur. In the Frasch process, sulfur separates cleanly from the gangue underground and comes to the surface in a very pure form. Surface sulfur deposits, particularly those in the Western Hemisphere, exist largely due to volcanic activity, and sulfur separation from the gangue is a formidable technical problem. None of the surface deposits are large compared to some of the Frasch deposits, but at the present sulfur price, they are certainly of economic importance. From the turn of the century until 1975, the price of sulfur was for the most part $18-$28/t. However, with the price of sulfur now over $154/t, there are a variety of technical alternatives to consider for sulfur surface ore separation that may not have been economically attractive a few years ago.

Jan 9, 1981

By L. J. Drew

The plate tectonic setting, regional geology, and certain aspects of the economic geology of the iron-rare-earth-nio-bium ore bodies at Bayan Obo, Inner Mongolia, China, were studied by a team of geologists from the Tianjin Geologic Research Academy and the U.s. Geological Survey between 1987 and 1989. These ore bodies were formed by hydrothermal replacement of Middle Proterozoic dolomite in an intracontinental rift setting. A variety of veins and/or dikes that have a carbonatite-like mineralogy cut the footwall clastic rocks and migmatites. A stockwork of veins occurs at several locations in the footwall. The hanging wall is a shale that has been converted to a K-metasomatite and has microcrystalline potassium feldspar as its principal constituent. This shale served as a sealing caprock that contained the chemical solutions that reacted with the dolomite and that created the enormous concentration of mineralized rock in an 18-kilometer-long syncline. The rocks that host these ore bodies and the associated mineralized areas occur today as roof pendants in granitoid rocks of Pennian age that were emplaced during a continent-to-continent collision during that period.

Jan 1, 1991

By George J. Hartman

The Fort Cady in situ borate-mining project involves recovering boron from a deposit more than 400 m (1,300 ft) below the surface. The resource recovery method is a new in situ mining technology that uses weak acid solution injected directly into the ore body. As the acid contacts the calcium-based ore (primarily natural colemanite), the contained borate values are digested as boric acid. This boric acid solution is then pumped to the surface by submersible pumps. A series of chemical reactions and precipitations are performed that result in the production of calcium borate. The borate values are then recovered as a finely divided solid white powder. The refined product is sold under the trade name Cadycal 100. The Fort Cady in situ borate-mining project is located about halfway between Los Angeles, CA and Las Vegas, NV in the Mohave Desert.

Jan 1, 1996

By D. A. Huggins

Column flotation is finding increasing use in the flotation of copper, molybdenum and other heavy metals and coal. Columns have proven operational, cost and metallurgical advantages which caused us to investigate their use in the proposed Escondida flowsheet. A comparative pilot plant test with 35 tons of ore showed that one column can replace three stages of cleaning and result in a significantly higher concentrate grade with no loss in recovery.

Jan 1, 1987

The Department of Health and Human Services (HHS), National Institute for Occupational Safety and Health (NIOSH), Office of Mine Safety and Health Research (OMSHR), with the assistance of cooperating underground mining operations and state agencies, has conducted research exploring devices and technologies that could be used to assist miners navigating through smoke and dust resulting from a fire or explosion. Recent events in mines confirm that smoke and dust can enter and contaminate mine escapeways creating an atmosphere with severely reduced visibility. This reduced visibility results in substantially increased escape times, possible disorientation or confusion, and increased stress levels, and may prevent evacuation altogether. Tools or devices that assist miners in navigating through smoke-filled areas void of lifelines could make the difference in successful escape from the mine. This paper presents the results of OMSHR research to identify and evaluate tools and devices that could provide meaningful information to evacuating miners in areas with limited visibility and without the benefit of a lifeline.

Jan 1, 2011