Search Documents

By R. L. Merrifield

Cominco Snip is a 60: 40 joint venture of Cominco Ltd. and Prime Resources Group Inc. Cominco manages the operation. The mine site is located in a narrow mountain valley where Bronson Creek enters the Iskut River in Northwestern British Columbia. Access is by air only to the company's 1,500 meter airstrip. Milling at a designed feed rate of 300 tpd began on schedule in January 1991. Tonnage and gold production in the form of bullion bars from the gravity circuit and gold bearing float concentrate have exceeded design forecast. This presentation will examine many of the factors that influenced the final plant design inclusive of exploration findings, bench scale and pilot plant test results, environmental and social considerations, capital and projected operating costs and product transportation alternatives such as the operation's Hovercraft.

Jan 1, 1993

By Gunter Fauth

The setting of tasks for the process control of coal cleaning, and in this connection the requirements for instrumentation can be classified into the following three fields: - Monitoring the operation of individual units, or process steps, - Control of units or process steps, - Control of the entire coal cleaning process with the intention of optimizing the operation and the profitability of the process. Instrumentation is affected by the type of cleaning processes. For introduction Figure 1 shows the simplified flow sheet of coal preparation which is usual in the German Ruhr District and in which desirable places for the measurement of ash, moisture and sulfur content are marked. The preparation plant is supplied with run-of-mine coal from the shaft via a homogenization facility. In a first step of primary classifying the raw feed coal is screened at about 10 mm. The raw coarse coal ( = 10 mm) is sorted by jig washers or heavy-medium separators. the raw fine coal (< 10 mm) at first is pneumatically sized at about 0.5 to 0.75 mm. The fines, the aspirated dust, are a finished partial product which will be added to the final metallurgical or steam coal. The material 10 to 0.75 mm subsequently is sorted in fine coal jigs and dewatered in centrifuges. The sludge obtained with the wet cleaning processes is dewatered in thickeners and fed to the flotation. Concentrate and tailings are dewatered by filters or bowl centrifuges and by chamber filter presses or belt filter presses, respectively. The partial products coarse coal, fine coal, flotation concentrate, aspirated dust, and middlings are blended to result in the sellable products metallurgical and steam coal.

Jan 1, 1984

By Jeffrey M. Listak, Gregory J. Chekan

The U.S. Bureau of Mines, in an effort to improve coal conservation and utilization is currently investigating longwall panel layouts to maximize coal recovery and minimize interactive problems in multiple-seam operations. When longwalling coalbeds in descending order, the transfer of stress from overlying gate roads is a major design constraint affecting pillar stability in the lower mine. The lower mine gate road pillars must be properly designed to withstand the additional load transfer if gate roads are superpositioned in successive seams. The Bureau&apos;s MULSIM/NL model was used to analyze load transfer mechanics for superpositioned gate road pillars. Analysis of Longwall Pillar Stability (ALPS), which is an empirically based design method for longwall gate road pillars, was used to calibrate model input parameters. The attributes of both the MULSIM/NL model and ALPS were combined to develop a modified method for estimating pillar stress for multiple-seam cases. The modified method uses a multiple-seam (MS) factor to estimate the stress on the lower mine gate road pillars when superpositioning is practiced. Numerical analysis shows that the MS factor is dependent upon the interburden thickness and pillar width and is presented in a series of graphs relating these two parameters. Several examples are included to illustrate the use of the MS factor for estimating lower mine pillar stress and resulting stability factors.

Jan 1, 1992

By John Mastoris, Kostis Dragasakis, Kostas Kouklidis, Shkurtë Gashi, Halil Berisha, Jenuz Bulica

Titan Group’s environmental policy and Sharrcem’s Corporate Social Responsibility (CSR) are the driving forces behind the development and implementation of a comprehensive Rehabilitation Plan at Dimce Quarry, which is the main raw material source for Sharrcem Cement Plant since the 1970’s, located in the municipality of Hani i Elezit in Kosovo. Based on an Environmental Impact Assessment Study and the approved Mining Plan and also on the principles prescribed in the Guidelines on Quarry Rehabilitation, released by the Cement Sustainability Initiative of the World Business Council for Sustainable Development (WBCSD-CSI), Sharrcem has adopted a quarry operation and rehabilitation process in line with the best practices in the mining and cement sector. This paper discusses the background for the development of the rehabilitation plan and the results of rehabilitation activities, as have been implemented over the last few years. The main objective of the progressive rehabilitation plan at Dimce Quarry is to restore the depleted pit and return it back to the original land owners for resettlement. To date approx. 3,4Ha of former mining area has been restored by backfilling and levelling of the depleted closed pit and returned back to owners, who have built their houses and turned it into a living area again. This Quarry has turned out to be a real composition and practical example of preserving and returning back the natural resources in a state compatible with the surrounding environment and with respect to the needs of the local stakeholders. The motivation for business to engage in rehabilitation activities in the first place lies in the belief that the development and implementation of a progressive and practical Quarry rehabilitation plan and restitution of the land will deliver significant environmental and social benefits that outweigh the long-term rehabilitation costs, while maintaining the company’s reputation.

Jan 1, 2017

By A. L. Hinde

Ideally, mill circuits should be controlled so that excessive random disturbances are reduced in frequency and amplitude. It is difficult to derive an objective measure of the effectiveness of any chosen control strategy. Often, the response of the circuit to pulse or sinusoidal disturbances is used as a measure of the effectiveness of control, but this is not adequate in many circumstances because such disturbances bear little resemblance to those that occur in practice, and such an approach cannot be easily related to the profitability of the reduction process. A superior approach appears to be the application of the theory of stochastic processes. This theory permits both real process disturbances to be modelled accurately, and useful objective functions for control to be derived. A test of the usefulness of stochastic theory in mill control was made on the gold ore milling circuit shown in Figure 1. This circuit was fed with an ore which had a liberation characteristic such as that shown in Figure 2. It is simple to show that, for such a liberation characteristic, the recovery of valuable mineral will vary as the standard deviation of the particle mass-size distribution varies even though the mean particle mass-size is kept constant. Similarly it may be shown that excessive perturbations in the circulating load in a milling circuit such as that shown in Figure 1 can affect liberation. Figure 3 shows how, as the cyclone feed density increases and the sump water addition decreases at constant sump level, the cyclone operation becomes unstable and the discharge "ropes? with a consequent catastrophic coarsening in product size. By minimising the variance of the circulating load it is possible to reduce the probability of initiating instabilities of this nature.

Jan 1, 1977

By W. E. Horst

In Part I of this paper we describe two techniques that were employed in the development of mathematical descriptions of the size reduction process which takes place in a ball mill. In Part II we show how the comminution model was imbedded in a process model to effect steady-state and dynamic simulation of a closed-circuit grinding operation. Increasing emphasis is being placed on development of approaches whereby the essential characteristics of a process can be succinctly represented in terms of a mathematical description of the relationships that exist among important process variables. This activity, commonly known as mathematical modeling, predates modern electronic computers: however, these computers with their tremendous computational capability have given new impetus to the whole field. Although the computer is quite helpful in the development of mathematical models, the real value to the engineer lies in the fact that computers represent such a powerful tool for simulating systems described by mathematical models. As a consequence, engineers may simulate and thereby study the behavior of complex. interacting, systems over a broad range of process variables and configurations once appropriate process models have been developed for the sequence of steps comprising the process.

Jan 1, 1970

Iron removal using biologically produced organic acids was investigated as a treatment option for the production of refractory grade bauxite. A leaching solution containing 98mM oxalic and 67mM citric acid was prepared from a sucrose medium using for fermentation the fungus Aspergillus niger. The leaching capacity of the metabolic product was tested on a bauxite sample containing 16-19% iron (as Fe2O3). Aerobic and anaerobic leaching tests were carried out at pH 3, 50°C and in the absence of light. Results indicated that more than 80% of total Fe can be removed from the ore, when the sample is finely ground and applying a two stage treatment. The presence of oxygen was seen to affect adversely the kinetics of the process, suggesting that leaching follows a reductive mechanism. Experiments that were carried out with different particle size fractions indicated that for obtaining efficient removal of iron particles should be finer than 0.63mm. Reduction of the operating temperature from 50 to 30°C caused a decrease in the rate of iron removal by more than 10 times.

Jan 1, 2006

By K. Katen

In another situation, Dave Zegeer, the Assistant Secretary of Labor for Mine Safety and Health, whom all of you know very well, would have taken the opportunity to talk with you. In his absence, however, I would like to reference some of his recent comments which may help us to see the issue of mine safety in historical perspective. Dave pointed out that this year is the eightieth anniversary of the Great Earthquake and Fire of San Francisco. The whole world heard about that disaster--it and the 452 people who died in it. In that same year, nearly five times as many people died in coal mines, but no one particularly noticed.

Jan 1, 1986

By C. E. Silverblatt

The advent of larger quantities of -1/4 inch coal in the raw feed to the preparation plant and the necessity of recovering this material has made the problem of meeting product moisture specifications more difficult. For a number of years thermal dryers have been used advantageously as a means of reducing fine coal moisture content where the over-all economics would justify such an installation. However, these units are not without their drawbacks because of high capital and operating costs, safety hazards and possible degradation of the product, and thus an alternative method of moisture reduction is highly desirable. After the various mechanical variables associated with filtration have been optimized, an examination of theory shows that surface tension and liquid viscosity are the only two remaining variables which might be altered to reduce moisture content.

Jan 1, 1964

By Chris Mills

El papel de la separacion gravimétrica en la industria minera es brevemente considerado en perspectiva. Las pruebas e intentos de laboratorio y mineralógicas para el diseñio de los procesos gravimetricos son examinados poniendo especial énfasis en la selección de la tecnologia del proceso. Es tratado y comentado el material disponible en equipos para pequeña escala y trabajo de pruebas-piloto, particularmente en relación a la escalacion y a la adquisición de datos precisos y fiables. El transporte del comportamiento de los datos desde la planta piloto a la planta a escala es igualmente explicado. Son resefiados todos los tipos de equipos a escala total existentes para la separacion gravimétrica, poniendo de relieve las unidades de alta capacidad. Es considerada la disposicion de la planta y la seleccion de 1os equipos auxiliares.

Jan 1, 1982

By T. E. Mccandless

Detrital minerals of mantle origin have been found in the Green River Basin of Southwestern Wyoming (Figure 1). Pyrope, pyrope-almandine, and chrome-bearing clinopyroxene and orthopyroxene occur on the antmounds of Pogonomyrmex Occidentalis. These antmounds are a common sight throughout the western U.S., and were used by early paleontologists as fossil mammal collection sites. The mound is composed of two types of material; (1) soil excavated during the digging of the nest below the surface (maximum depth 3 meters) and (2) larger grains collected from the surface and placed on the mound, probably to prevent erosion. The selection of grains to armor the mound seems to be based largely on the mean diameter of the grain, with other factors such as weight, sphericity, roundness and composition in decreasing order of importance (Wheeler and Wheeler, 1963). The minerals of this study happen to fall within that mean diameter range. The garnets are found on the mounds as 3-6 mm diameter subrounded to subangular grains. The pyroxenes are also 3-6 mm in diameter and are most commonly subangular laths. The minerals themselves show evidence of abrasion, such as frosted surfaces and rounded edges. Orange peel texture is present on some of the grains, which suggests that kelyphitic rims were once present, but have been removed. Also, no similar minerals were found in sieved soil auger samples to depths of 2 to 6 meters taken near the antmounds. These observations imply a distal rather than proximal source for the minerals. Lamproitic rocks of upper mantle origin are found bordering the "Green River Basin. The best known are the Leucite Hills, a series of ultrapotassic volcanics found on the north flank of the Rock Springs Uplift (Carmichael, 1967). Minor occurrences of mica peridotite and ultrapotassic volcanics are also found on the western end of the Uinta Mountains in Utah (Best, et al, 1968). None of these rocks are known to contain minerals like those on the antmounds. The garnets are comprised of purple chrome pyrope, red chrome pyrope-almandine, and pink to orange low chrome pyrope/pyrope-almandine. Oxide statistics for these groups are summarized in Table 1. These three groups are distinct when their Cr203 values are plotted against magnesium number (Figure 2). The chrome pyropes are highest in Cr203 (1.28-2.66%) and have high, restricted Mg number values (0.781-0.826). The chrome pyrope almandines have similarly high Cr203 (1.29-2.62%) but a lower Mg number range. The low chrome pyrope/pyrope-almandines have the lowest Cr203 content (0.09-0.73) and the widest Mg number range (0.534-0.836). Using the classification scheme of Dawson and Stephens (1975) the chrome pyropes are most similar to garnets derived from kimberlite and from garnet lherzolite, websterite, and harzburgite xenoliths in kimberlite. The chrome pyrope-almandines and the low chrome pyrope/ pyrope almandines are similar to garnets derived from eclogite nodules (Figure 3).

Jan 1, 1984

By Michael Cruickshank

All life on Earth relies on the ocean and yet the ocean is 95 percent unexplored, unknown and unseen by human eyes,? said Paula Keener, director of education programs for National Oceanic and Atmospheric Administration?s (NOAA) Office of Ocean Exploration and Research. ?To better understand, manage and protect the ocean and its resources, NOAA believes it is critical to use the best technology to explore, discover, inform, educate and motivate? (MTS, newsletter, January 2011). In the last few decades, our understanding of the global mineral resource base has been drastically changed by some surprising new developments. The potential for commercial minerals per unit area in the oceans and seabed appears to be similar to that of the terrestrial lands. Thus, almost three-fourths of the global mineral resources are in, or under, the sea and are virtually undeveloped. The area of the Pacific seabeds alone is greater than the total area of the global lands. Half of the global seabed minerals are now controlled by nation states within their Exclusive Economic Zones (EEZ). The other half is controlled by the United Nations (UN) through the International Seabed Authority (ISA) within the ?areas beyond national jurisdiction? known as The Area. Thus, the Law of the Sea, ratified in 1994, has resulted in the largest transfer of control of natural resources in the history of mankind. This paper was prepared by the Society for Mining, Metallurgy and Exploration (SME) Committee on the Offshore Technology Conference for the SME Board of Directors and other interested parties. As the premier professional society for the mining and mineral community in the United States, with a history dating back to the 19th century, SME?s mission is to encourage and support young men and women engineers in the minerals industry, provide the services they need, improve the image of the industry, strengthen the networking among global industry professionals and engage in proactive collaboration among industry, government, academia and nongovernmental organizations (NGOs). The accomplishment of this mission can be strongly advanced by highlighting what is probably now the most significant development in the history of the modern minerals industry - the exploration of the marine environment and the understanding of the potential for the development of the minerals therein.

Jan 1, 2011

By Eleanor Sonley

In October 2000, temporary seismographic stations were installed above the Trail Mountain Mine, Emery County, Utah, USA to supplement a regional network. Over seven months, 1826 mining-induced seismic events were recorded with a magnitude range of M 0 to M 2.2 (Arabasz et al., 2002, 2005). Routine event locations for this dataset cluster around the longwall mining activity during the recording interval. However, applying a double difference relocation technique to the routine locations significantly improves the correlation between mining activity and event location. The resulting relocations depend greatly on station distribution and the number of arrival time picks. We use this dense temporary array to assess station distribution requirements for applying the double difference technique at other mines by systematically removing data from available stations, thus simulating sparser networks. The insight gained using the Trail Mountain dataset is used to develop a metric for assessing the usefulness of above-mine networks and to develop a tool for expanding seismic network coverage. To verify the appropriateness of these tools for wider application, we examine data from two additional mines located in the western United States. Improving the relative locations of mining-induced seismic events highlights the association of these events with active portions of the mine. Clusters, regions of quiescence and relative timing of events can be used by mine operators to assess hazard, optimize production, and evaluate performance of mine plans. The lessons learned from this study may be used in future network design to improve accuracy of event locations at other mines.

Jan 1, 2009

By J. J. Scott

As a Rock Mechanics investigator, the author has, Over his career, attempted to use his best knowledge in developing better rock control fixtures. Based on the experience of nine years of development of friction rock stabilizers, in 1980 he decided to launch a new investigation to develop a unique roof support fixture which would fit the coal mining market. The largest single user of roof bolts in the world is the American coal mining industry, historically using up to 100 million fixtures per year. In 1989 they used approximately 82 million fixtures.

Jan 1, 1990

By R. Fuenzalida

Since 2007, a number of Multivariable Predictive Control (MPC) Applications have been implemented on SAG mills, among others, within the Kairos Mining Concentrator Automation Program using ?Profit Controller?? and other tools comprising the ?Profit Suite??. Along this journey, several interesting and challenging issues related to SAG mill operation and control have been faced, which are relevant to be shared with the Mineral Processing community. These advanced control applications have an operational objective whose goal is to increase marginal profit on the concentrator, together with increasing mill stability. In regard to this objective, the issues to be presented and described are in direct relationship with ?Profit Controller? features and the SAG role; they are also stated and linked to get the most of the mill. Some conclusions and findings are also presented, leading to recommended practices on how to use the controller. These findings have also lead us to decide further actions to be taken on new applications to deploy and also on devising and implementing some complementary components to increase robustness of the overall automation solution, as well as reducing the need for operator intervention.

Jan 1, 2012

By S. K. Singh

"Feather edging"-a major source of injury and fatal accidents in Australia, South Africa and USA, refers to a phenomenon where the roof, at the goaf edge, falls as a thin wafer of rock often suddenly, over-riding conventional timber breakerlines. It may run down and affect adversely a working bord at distances of 15 metres or more from the goaf edge. Feather edging typically occurs in relatively massive, strong roof strata such as sandstone or conglomerate. This paper presents the results of a mine trial where a concentrated row of fully grouted bolts were able to resist the feather edging in the first comprehensive, monitored trial in an Australian pillar (&apos;total&apos;) extraction coal mine.

Jan 1, 1999

By Ahmed I. A. Salama

The problem of estimating separation characteristics by utilizing mass distributions of feed and products is considered. The separation characteristics include mass yield and partition curve. The cases of mass balance and partition functions balance are identified. The developed techniques can handle the cases of two- and three-product separation. Actual data are utilized to demonstrate the proposed techniques.

Jan 1, 1992

By F. N. Kissell, C. D. Litton

This study predicts the level of smoke that miners might meet while trying to escape a coal mine fire and describes how smoke would impede their safe escape. For this study, the authors assumed that miners exit through an escapeway adjacent to the burning entry, that some air would leak from the burning entry to the escapeway. The following conclusions were made: • A very low amount of air leakage to the escapeway can produce a critical level of visual obscurity from smoke. This shows that intake airways may be as susceptible to smoke visibility problems as return airways. • This critical level of smoke obscurity is reached much before a critical level of carbon monoxide is reached. • Small fires can cause a severe sensory irritation that further limits vision. Thus, reliable eye protection is very important. These results show that methods to guide miners through dense smoke will contribute greatly to saving lives during mine fires.

Jan 1, 1993

By Peter J. Szabo

Many mining engineers tend to think of the economic analysis of mining ventures and projects on an f.o.b. mine basis. This is especially true of mines that are operated in an established domestic mining district. Here, transportation costs are many times smaller in comparison to overall delivered prices. One has only to consider the development economics of taconite mines in Minnesota with production destined for lower lake ports to see the truism of this statement. In the international arena, however, with consumers such as Japan and Europe located thousands of miles from source countries such as Brazil and Australia, the situation is different because mineral transportation is often a critical factor in determining project viability. This article is being presented to provide a basic understanding of the factors that govern ocean transportation of the three largest bulk mineral commodities shipped around the world: iron ore, coal, and phosphate. The major dry bulk commodity trades as a percentage of volume shipped are iron ore, 45%; grain, 25%; coal, 20%; phosphate rock, 5%; and bauxite and aluminum, 5%. Most of these commodities are carried by bulk carriers rather than tankers. These are vessels that have cargo, usually in solid form, loaded directly into the hold of a vessel by shore-side materials handling facilities or, in the case of a geared bulk carrier by the vessel&apos;s cranes and derricks. Gearless bulk carriers are used in most cases for iron ore and coal. Geared bulk vessels are mainly used for minor dry bulk trades such as ore concentrates (copper, lead, zinc, etc.), fertilizers (phosphate, potash, etc.), cement, petroleum, and coke. There has been, however, a trend toward using more self-unloading ships in both iron ore and coal ocean transport. And large vessels, such as the Universe Kure of Japan, have been designed with a cargo capability of 157 kt (155,000 dwt (deadweight tons)). Trade patterns of major bulk commodities are influenced by the Panama and Suez canals. Both of these canals have draft limitations that prohibit large, deep-draft, ocean-going vessels from using them for shorter trade routes used by Panamax and Suex vessels. The shipping industry has developed two widely used vessel classes; the Panamax and Suex vessels. The former is the maximum size vessel that can pass through the Panama Canal, usually 51-61 kt (50,000 - 60,000 dwt), depending on the season and draft of the vessel. The Panama Canal is usually 0.6-0.9 m (2-3 ft) deeper in the winter than in the summer. Thus, less cargo can be carried by the same size ship in the summer through the canal than in the winter. The Suex vessel is in the 71-81 kt (70,000-80,000 dwt) class. This larger vessel is able to transit the Suez since Egypt deepened the canal following the Seven Days War. Recently, the Suez Canal has been deepened to accommodate vessels with drafts as deep as 152 kt (150,000 dwt).

Jan 10, 1982

By S. Veeramasuneni, C. D. Dunbar

The rate of hydration influences many important physical properties of gypsum. Previous research examined the rate of gypsum hydration and related this to compressive strength and microstructure development using BET specific surface area analysis. The analysis of gypsum porosity in combination with BET surface area and rate of hydration remains to be done. In the present study, mesoporosity is analyzed using the numerical method of Barrett, Joyner and Halenda (BJH) to gain a greater understanding of gypsum hydration and microstructure development. The rate of hydration has a significant effect on mesoporosity of the gypsum matrix. The results reveal the effect of mesoporosity and hydration rate on some macro physical properties of gypsum.

Jan 1, 2000