Search Documents

By Earl F. Mathers

Few people would question that coal is king in the Campbell County, WY area. Other industries, such as oil production and ranching, also contribute significantly to the economic base, but coal mining and related industry development dominate. In recent years, Gillette has become the commercial hub of northeastern Wyoming. This development has been largely a response to the growth of the coal industry in Campbell County. Historically, Campbell County developed as a ranching area, a process that was aided by the passage of rail lines through the area, allowing early ranching interests to get their livestock to market. For decades, the Gillette-Campbell County area was predominantly a ranching area that experienced only incremental population growth.

Jan 1, 1994

By D. M. Larsen

Since start-up in 1985 the Cannon Mine has produced and shipped a 170 g Au/tonne (5 oz Au/ton) flotation concentrate to various smelters for gold and silver recovery. Several processed have been investigated to economically produce dore' at the mine site from the refractory concentrate. This paper describes recent laboratory and pilot scale test work utilized in the process design and engineering feasibility study of a 73 tonne/day (80 ton/day) pressure oxidation and CIL facility. The designed pressure oxidation circuit utilizes a series of vertical autoclave units operating at 170°C (338"F) and 1.4 MPa (200 psig). Projected operating costs are discussed.

Jan 1, 1993

By P. Perruzza, R. Grandori, A. De Biase, A. Ciamei, A. Busillo

The Turin metro alluvium soil is mainly made of large boulders, cobbles and gravel , few sand and almost no fines. This grain size curve is out of the range of application for EPB and Slurry TBMs. In order to bore 5 of the total 7,5 kms of Line 1 tunnel, two specially designed Lovat EPB TBMs were utilised in combination with a systematic non structural pre-grouting of a small volume rectangular slab just above the tunnel section. The same pre-grouting was not however applicable for lack of access on surface in some sections of the remaining 2,5 km of tunnel that had to be bored below important buildings/structures, with under ground water pressure up to 1,5 bar, with curves radius of 180 m only. For these more critical sections it was necessary to study and implement a new technical solution and improve the capacity of the TBM to work efficiently in EPB mode even in this unsuitable ground and overall conditions. After months of studies the selected and adopted solution has been to inject inside the cutterhead chamber, in addition to the almost standard foams & polymers additive mixes, a suspension of limestone powders. This with the scope of compensating the lack of fines of the natural ground with rock powders.

Jan 1, 2005

By L. Lacerda

Spray-on ground support membranes (GSM) or thin support liners hold today perhaps as much potential to impact underground (u/g) ground support operations as dry and later wet-mix shotcrete when introduced to mining in the latter part of the 20th century. This emerging technology has come a long way from the time the first single component experimental coatings were tested in the mid-1980s. Due to a number of factors, including occupational health risk and mine safety regulations, it has taken quite some time for the development of non-hazardous membrane products. However, at this junction most existing u/g mines that employ more conventional forms of ground support could benefit from evaluating GSM technology as a means of improving safety and the bottom line. The same is especially true for future mine developments. This paper describes Master Builders Inc.’s CS1251 GSM product and its implementation. It discusses the situations in which GSM may replace other forms of ground support. Furthermore, it evaluates GSM costs & safety issues and looks at present applications and the potentially bright future of this technology.

Jan 1, 2002

By R. L. Grayson

Compliance standards for respirable dust which are reduced because of high quartz concentrations have become an industry-wide problem. Research on the physical and chemical character of quartz-classified particles in respirable coal mine dusts indicates that they may exist in intermixed layers or may be coated by clay or coal material. The relative amount of intermixing varies with the coal seam being mined. If most of the quartz particles of a mine dust are "pure," then the dust may have a high fibrogenic risk potential because of truly free silica and the compliance standard should be lowered. If, however, the quartz is locked inside another material matrix, or coated, a reduced compliance standard may not be appropriate.

Jan 1, 1990

By I. M. Ahmed, R. S. Hassan, M. I. Aly

Extraction and separation of La, Sm and Dy ions from acidic sulfate-phosphate solutions was investigated using a cation exchange extractant, bis(2,4,4-trimethylpentyl) phosphinic acid, CYANEX 272, in kerosene. The influence of shaking time, equilibrium pH, extractant, sulfate and phosphate ion concentrations, diluent type and temperature was studied. The extraction was found to be pH-dependent, and increasing the phosphate ion concentration inhibited the extraction which was found to be endothermic. The stoichiometry of the extracted metal species was found to be MOH.H2OHSO4H2A.A2. Aliphatic diluents were found to enhance the extraction compared to aromatic diluents. The results showed that there was a separation mode between the metal ions when varying the hydrogen ion and sulfate ion concentrations, under the used experimental conditions. The investigated process was used for the recovery of La, Sm and Dy from the acid solution resulting from the leaching of low-grade monazite.

By V. K. Gupta

A detailed experimental study of the variations in grinding rate with particle size, particle load, ball diameter, ball load, mill diameter, and mill speed was carried out for a soft cement clinker and a hard cement clinker. The effects of the ball diameter, ball load and particle load were observed to be material (hardness) independent, and those of the particle size, mill diameter and mill speed to be material dependent. A sharp change in the grinding behavior was observed for both the clinkers at about 150 µm size. Below this critical size: (i) the hardness difference between the two clinkers became insignificant, (ii) variation in the grinding rate with particle size became markedly more pronounced, and (iii) mill speed had little or no effect on grinding rate. The importance of these results in the context of process optimization and control is discussed.

Jan 1, 1987

By Thomas D. Boyce

Minewater from many western U.S. uranium mines often contains radioisotopes in concentrations higher than permissible for discharge to unrestricted areas. .Radium 226 has the lowest permissible concentrations of all radioisotopes and usually greatly exceeds this limit in untreated effluents. This radionuclide is derived from the natural radioactive decay of uranium: [ ] The treating of minewater effluents has been studied previously (1) and the classical removal method for radium has been adsorption on barytes or freshly precipitated barium sulfate. This paper describes the removal of radium from minewater by utilizing a selective complexer based on a crosslinked organic polymer matrix.

Jan 1, 1982

By Steve Kral

Invensys is a London-based supplier of automation and control systems to a variety of manufacturing and processing industries. Through its global subsidiaries, Invensys provides customized, advanced process control systems and networks for automating industrial plants, including mineral processing plants. The company employs more than 80,000 people worldwide in its four divisions. They include Automation, Control, Powerware and Software Systems. These four divisions work together to design the complete package for their customer’s automation and process-control needs.

Jan 1, 2002

By Walter E. Dean

Deep-sea manganese nodules are considered to be potential ores of manganese, nickel, cobalt, and copper. Considerable time, effort, and funds have been applied to the study of Se distribution of nodules on the sea floor and the location of economically important areas, but little effort has been spent in understanding the origin of nodules. Most theories that have been proposed to explain the origin of manganese nodules have been based on inorganic physicochemical processes. It is not by coincidence, however, that the area considered to be most economically feasible is in the zone of high biological productivity in the eastern equatorial Pacific Ocean and underlain by siliceous biogenic sediment. The genesis of manganese nodules and the concentration of many trace elements are intimately associated with biological processes.

Jan 1, 1982

By George White

On June 25, 1876 Lt. Colonel George Armstrong Custer led the Seventh U.S. Cavalry Regiment., comprising 31 officers and 637 enlisted men, into the valley of the Little Big Horn River in southern Montana. His assigned mission was a reconnaissance-in- force to locate the Indians reported to be assemblying in that area. Custer was extremely successful in locating the Indians. Unfortunately he located more than 3000 Cheyenne and Sioux under the leadership of the great war chiefs Crazy Horse and Gall. Custer's entire battalion of more than 200 men was annihilated; there were no survivors. While I don't seriously suggest that things will be all that bad in the uranium industry, I do suggest that some very fundamental changes have occurred in the uranium market. Conventional thinking based on past truths will no longer suffice. Geology, economics, politics, nuclear growth pat terns, technology, and utility attitudes have all changed. New thinking is in order. It is at this point that I would offer my usual disclaimer. My views regarding the future are simply that--my personal views. My belief that certain events will come to pass does not mean I view those events as appropriate, wise, good, equitable, or economic.

Jan 1, 1985

The only significant iron ore deposit in Hungary could be found in Rudabánya. The mine was closed in 1986. The area of Rudabánya was always the home of heavy mining activity. In former times, mainly silver and other non -ferrous metals were excavated.

Jan 1, 2011

By Thomas Fenner

Surface and underground mining operations are often hindered by unknown tunnels and slopes and the precise locations of adjacent workings. Mine safety and planning are adversely affected especially in previously undermined areas where historical records are incomplete or nonexistent. The results of several ground penetrating radar (GPR) studies for the detection of known mine tunnels in underground coal, salt and gold mines are presented. A case study to locate unknown, abandoned mine workings at a surface gold mine successfully located all workings to a depth of 11 m (36 ft).

Jan 1, 1996

By S. M. Moore, J. F. Burr, R. Fernando, D. Snyder

"The Mine Improvement and New Emergency Response Act of 2006 (MINER Act Public Law 109-236) was passed by Congress in response to three major underground coal mine accidents in the United States that claimed the lives of 19 miners. The Act resulted in substantial changes in the underground coal industry relative to the use of technology for mine escape, rescue, disaster response and other areas where the lack of these technologies contributed to the fatalities caused by these tragedies. This year marks the 10th anniversary of the MINER Act, which makes it an opportune time to reflect on the events that led to its passage, the changes that have been made since then, and the work that remains to be done. As discussed below, the last decade has demonstrated tremendous cooperative efforts among mining operators, technology innovators, labor, The National Institute for Occupational Safety and Health (NIOSH), the U.S. Mine Safety and Health Administration (MSHA) and state regulators, resulting in substantial improvement of the technologies used for escape and rescue and noteworthy progress toward meeting many of the goals of the MINER Act. While the MINER Act and this article pertain primarily to coal mining, many of the technologies are equally applicable to any underground mining and have already found some acceptance outside of coal. TECHNOLOGY GAPS TARGETED BY THE MINER ACT The MINER Act addressed several technology challenges: • Problems with donning and switching between self-contained self-rescuers (SCSRs). • Poor visibility in smoke. • No wayfinding assistance for escape from the mine. • Limited breathable air supply. • Inability to locate trapped miners. • Inability to communicate with trapped miners. • Failure of mine seals. The MINER Act had several provisions that prescribed specific safety technologies intended to address these issues. Many of these were directed at post-accident technology requirements — an area in which Congress mandated additional technology investment. Specifically, the Act required mine operators to submit emergency response plans (ERPs) that contained provisions for implementing new or improved post-accident communications, tracking, lifelines, refuge alternatives and breathable air supplies along with training for emergency procedures and local coordination of emergency response. Most of the requirements were to be carried out within three years of the ratification of the MINER Act. In addition to these requirements for mine operators, the Act clarified and expanded NIOSH’s role and authority in enhancing the development of new mine safety technologies and expediting their commercial availability. The MINER Act also required NIOSH to develop research on refuge chambers, mine seals and the use of belt air and fire-retardant belts. Mine seals had to be upgraded and MSHA turned to NIOSH for applied research to establish the new explosion-resistance requirements. Progress toward closing the gaps."

Jan 1, 2017

By E. Allen Hendt

It is a pleasure to be invited to speak before a gathering of executives representing America's leading mineral companies, I welcome this opportunity, particularly because it comes at an important period in the development of U.S. commodity policy. This morning, I discussed our general commodity policy primarily in the. Context of the north-south dialogue between developed and developing countries. This afternoon, I would like to focus more specifically on potential cartel activity and U.S. mineral import dependence.

Jan 1, 1978

By J. R. Sturgul

Thompson and Adler (1988) present a new simulator for use in designing conveyor belt systems for underground mines. Their model uses a large Fortran program to do a Monte Carlo simulation. Their approach is similar to that done by other researchers, such as Stanford (1965) and Newhart (1977). All Fortran based simulation models use an imaginary clock that is advanced a time increment. At each advance of time increment the program has to determine what is to take place in the system. Since many things can take place at different places in the system, this approach requires that a large amount of logic is needed at each step of the program. This, then, necessitates a great amount of jumping between different portions of the program. In fact, the Fortran program, CMBCS, takes up to 15 to 20 minutes to run on the mainframe and several hours for the PC. Such execution times are typical of Fortran based simulation studies. There have been other examples of Fortran based simulation studies in mining. Cross and Williamson (1969) presented a model of a working open-pit copper mine. Fosinato (1982) presented a model of the bucketwheel excavators for the large open-pit mines in Southern Victoria in Australia. These excavators discharge into a complex conveyor system, which can be thought of as being similar, but more complicated than the one modeled by CMBCS. All previous simulation studies using Fortran as the source code have several things in common: they all are very lengthy, often being of the order of 10,000 lines of code and take a great deal of CPU time to execute. The program of Fosinato takes more than 4.5 hours to run on a large mainframe. Also not mentioned by Thompson and Adler is the actual time it took to write the Fortran code. This, too, can be considerable, as Fosinato's program took several man years to write and de-bug. In order to change it, as the parameters change or as the mine increases, further large amount of time is needed. An alternate to such Fortran based programs is provided by using a special computer language known as General Purpose Simulation System (GPSS). This language is designed to solve a wide variety of discrete event simulation problems and appears to be particularly suited for mining situations as shown by Sturgul and Yi (1 987). Although GPSS was introduced as far back as 1961, it has not been used in mining to any great extent. However, the original form was quite crude and inefficient compared to modem versions. Perhaps with the increasing popularity and availability of these recent versions, this will change. Two such versions are GPSS/H for the mainframe and GPSS/PC for the personal computer. GPSS/H allows for interactive usage, such as allowing input data to be entered via a menu. GPSS/PC has excellent graphical capabilities and one can actually view the simulation in progress. In addition, one can halt the simulation and change values of various parameters. If a particular portion of the simulation is in progress via a concept known as "microwindows." These new versions have greatly increased the potential for using the language for mining situations. Mining applications of GPSS have been given by Sturgul and Yi (1987), Sturgul and Harrison (1987), Sturgul (1987), and Sturgul and Singhal (1988). Schriber (1987) presents a summary of the recent advances in GPSS.

Jan 1, 1987

By D. H. Warren

This presentation we hope will provide you with an orderly approach co mine and surface plant closure taken from our experience over the past several years on six different projects within the intermountain states. There is no magic to the approach. It is basic common sense and yet it is interesting how many of the specific details are overlooked due to the individual complexity of each site. Our attempt here is to share some of the issues that have confronted us on these six sites. Please recognize that it is impossible to be all inclusive. Of the six sites we have drawn from; two are mine, mill and smelter sites dating back to pre-1900, one is an industrial site dating back to the early 1900s, two are mill and concentrator sites dating from the late 1940s and one is a mining district site dating from the late 1800s.

Jan 1, 1989

By W. G. Stevenson

The centennial celebration of the AIME provides an opportunity to review some aspects of developments in mineral exploration since 1871 and to reflect on the changes that have occurred. During this period seven Factors have fundamentally altered the procedures, techniques and philosophy of mineral exploration. Although most of these developed gradually, and unheralded, they have drastically altered the art of exploration and discovery. 1. ADVANCES IN MINING AND MILLING The development of huge shovels, draglines, trucks and track-mounted drills, to replace the wheelbarrow and single Jack has drastically expanded the rate of production for both underground and surface mining. The development of selective flotation has had a far-reaching affect on mineral exploration and has made it possible to extract metals from the metallurgically complex deposits discovered years before. These developments have reduced the costs of mining and treatment, and have transformed material into ore that was considered waste one hundred years ago. These advances have permitted exploration for progressively lower grade and larger mineral deposits.

Jan 1, 1971

By J. D. Megeath

In the October 1988 issue of MINING ENGINEERING, J.G. Wargo's paper discusses the problem of measuring and analyzing permeability, porosity, and fracturing in its relation to in situ leaching of disseminated gold deposits. This paper made me suspect that a good deal of information and analysis may have been done on this in reverse in the petroleum industry. Some years ago, I was involved with the US Geological Survey in a project studying the Devonian shale of the eastern United States. The Devonian shale contains gas deposits that have the characteristic of slowly seeping gas over a very long time period. To understand the rate of seepage, considerable study and analysis was done on the interrelationship of poros¬ity, permeability, and fracturing. The purpose was to find out how and why the gas could escape in the varying rates found in wells throughout the formation. It strikes me that this is the mirror image of the problem faced in attempting to understand how a cyanide solution will travel into a deposit. To possibly invent our own personal wheel a little faster, I would suggest a look at the work done on the Devonian shale. Some of it is contained in "Estimates of Unconventional Natural-Gas Resources of the Devonian Shale," US Geologi¬cal Survey Open-file Report 82-474, 1982, and "Additional Data for the Estimates of Unconventional Natural-Gas Re¬sources of the Devonian Shale," Open-file Report 83-676, 1983. It is entirely possible that some of this previous work could shorten the time required to make in situ leaching of dissemi¬nated gold deposits a profitable technique.

Jan 1, 1989

By Stephen B. Doppler

INTRODUCTION Following the world stock market debacle in October 1987, it would have been foolhardy to expect that securing equity funding in 1988 would be easy. Indeed, major equity financing's for gold mining companies have until recently been few and far between in the weeks and months following Black Monday. As a result, gold bullion loans have taken on an increasingly important role among producing firms in the industry. During 1988, the role of bullion loans has become increasingly complex and controversial. Some observers herald the emergence of a new breed of bullion loans - such as the 1,000,000 ounce loan to Newmont Mining, and the 400,000+ ounce facilities drawn down by Bond International Gold and Placer Pacific - as both increasing the public's awareness of the technique, and representing the dawn of a new age of gold financing. But are these recent loan facilities significantly different than those issued worldwide during the early to mid 19801s? Similarly, observers have voiced concerns regarding the role that gold loans play in the world's bullion markets, specifically in relation to their impact on prices. Have the new generation of mega-loans depressed current and future prices? Has the current surge of bullion loans irrevocably changed the nature of the gold market? Is there an upper limit on the number and size of gold loans?

Jan 1, 1988