Search Documents

By D. Park, V. Gall

The three-dimensional finite element technique combined with a progressive failure approach were used to simulate stress distributions in a complete mine section that occur in response to a longwall mining operation. Due to the availability of a Cray supercomputer, a large-scale, three-dimensional, finite-element model was developed for the analysis. The Hoek-Brown failure criterion, which describes a realistic behavior of rock masses, was used for the simulation of progressive failure. A comparison of calculated and monitored stresses in the mine has shown that the model gives a good representation of stresses in the mine structure.

Jan 1, 1992

By V. Gall

The three-dimensional finite element technique combined with the progressive failure approach was utilized to simulate stress distributions in a mine section which occur in response to a longwall mining operation. Due to the availability of the Cray supercomputer, a large-scale three-dimensional finite element model was developed for the analysis. The Hoek-Brown failure criterion, which describes a realistic behavior of rock masses, was used for the simulation of progressive failure. A comparison of calculated and monitored stresses in the mine has shown that the model gives a good representation of stresses in the mine structure.

Jan 1, 1990

By George L. Atwood

The Monsanto Company's Henry Mine is located 17 miles northeast of Soda Springs, in the southeast corner of Idaho. Ore being mined is phosphate rock which lies in the Permian Phosphoria formation. The ore is the raw material for Monsanto's three furnace elemental "P" plant near Soda Springs. The finished product from the furnaces is elemental phosphorus which is subsequently used in the manufacture of detergents, food preservatives, fire retardants and other consumer items. Mining is by open pit methods using 0-9 crawler tractors to rip and push-load rubber tired scrapers in stripping and mining operations. The equipment spread consists of six D-9G crawler tractors, four Caterpillar 6578 scrapers, eight Euclid S-24 scrapers, one Reich T750 drill and one Caterpillar No. 16 patrol plus various support equipment. Stripping is performed on a 12-month basis, two shifts per day. Mining is performed mainly in the summer months on a one shift basis. The hauling season begins May 15 and ends November 1 due to freezing weather and snow conditions. Annual production is 1,000,000 tons of phosphate rock and 2,500,000 to 3,000,000 yards of stripping. Stripping, mining and hauling is performed for Monsanto by Dravo-Soda Springs, a mining contractor. Dravo-Soda Springs owns, operates and maintains all equipment used in stripping, mining and hauling. The contractor is paid for stripping by the bank yard and for ore mined and hauled on a tonnage basis. The Monsanto elemental phosphorus plant began production in 1952 with ore being trucked to the plant from the Ballard Mine. Haulage was over public roads in 15, 24-ton semitrucks. A private haul road was constructed from the Ballard Mine to the Monsanto Plant in 1958 and 1959 to accommodate trucks with two twenty-yard trailers. This 11/ mile road was first used in the 1959 hauling season. In 1965, five new Kenworth tractors with two, 'forty yard trailers were introduced into the haulage system. These units carried 120 ton payloads and were used until

Jan 1, 1972

By David D. Eyer

Since the decade of the 1990s is nearly upon us, I have focused on what I see are the likely trends featured in new large underground coal mines 10 years from now. I do this from the vantage point of having been involved in the installation of large mines for more than twenty years. Little of the equipment resources we have available today was unknown when I entered the coal business in 1960. There were continuous miners, longwalls and diesel-powered equipment in Europe, monitoring systems, computers, heavy media separation systems, froth flotation and conveyors then as there are now. A substantial evolutionary process has occurred with these and other mining machines and processes. Some evolved only to die out, such as boring-type continuous miners; others, such as longwall systems, flourished. My intuition tells me that since there have been largely evolutionary rather than revolutionary developments in the near past, the same is true of the future, at least for the next 10 years. In other words, the elements of what are in the future are with US now. Some, such as computer-based applications, may evolve beyond our wildest dreams -but I doubt it.

Jan 1, 1988

By Robert A. Irvine

Traditionally, cost effective gains in the capacity of material handling systems were a result of increases in equipment size. In general, the use of maximum capacity components in a system optimizes the production "costs per ton." The trend-"Bigger is Better" will continue in material handling equipment. Since it is rare for plant operators to lament an over abundance of screening capacity, one can safely predict that vibrating screens will follow this trend. Large Vibrating Screens - The Challenge Large vibrating screens represent a unique challenge for Manufacturers, Plant Designers, and Plant Operators. The inherent mode of operation for vibrating screens is self-destructive. More often than Manufacturers admit, Designers plan for, or Operators staff for, a vibrating screen succeeds and self-destructs. This is a problem. It can magnify with larger vibrating screens.

Jan 1, 1983

By A. N. Pritchard

The development of vibrating screens over the last century has seen many variations to suit the exacting requirements of industry. Indeed, as each year passes, industry has presented the challenge to screen manufacturers of supplying larger machines than those used in the past and the question is often posed - what is the maximum limit? Not only must size or screen area be considered but excellence of performance in terms of screening efficiency must be maintained or maximized.

Jan 1, 1983

By M. J. Hrebar

A study was conducted to evaluate the applicability of large wheel loaders (Caterpillar 994 Class) for use as primary loading equipment in open-pit iron-ore operations. Field visits were made to taconite and gold mines that used large wheel loaders. Information was gathered on loader selection rationale; operation and maintenance experience; and production, availability and costs. Brief time studies were conducted to indicate machine performance and utilization. This paper summarizes the field data that was collected, including an economic comparison of wheel loaders and cable shovels in an iron-ore application.

Jan 1, 1998

By M. J. Hrebar

A study was conducted to evaluate the applicability of large wheel loaders (Cat 994 class) as primary loading equipment in open pit iron ore operations. Field visits were made to taconite and gold mines that used large wheel loaders. Data were gathered on loader selection rationale; operating and maintenance experience; and production, availability, and cost information. Brief time studies were conducted to indicate machine performance and utilization. The paper summarizes the field data and includes economic comparisons of wheel loaders versus cable shovels in an iron ore application.

Jan 1, 1996

By M. J. Hrebar

A study was conducted to evaluate the applicability of large wheel loaders (Caterpillar 994 Class) for use as primary loading equipment in open pit iron-ore operations. Field visits were made to taconite and gold mines that used large wheel loaders. Information was gathered on loader selection rationale; operation and maintenance experience; and production, availability and costs. Brief time studies were conducted to indicate machine performance and utilization. This paper summarizes the field data that was collected including an economic comparison of wheel loaders and cable shovels in an iron-ore application.

Jan 1, 1997

By D. R. Zeni

Today's mine development requires the safe, expedient and economical construction of vertical shafts for both ventilation and access. This construction must be accomplished within diverse ground conditions. Advancements in large-diameter shaft drilling have led to many exceptional mechanical refinements in shaft-drilling technology. The author traces the history of the equipment and methods employed by the large-diameter shaft-drilling industry and explores the likely paths of future development. Case histories that illustrate the adaptability of shaft drilling as a versatile tool for advanced, worldwide mining operations are cited. Safety, scheduling, costs, environmental impacts and capabilities are discussed.

Jan 1, 1996

By Bradford F. Townsend

A study was made on six collapses that occurred during large-diameter tunnelling through weak sedimentary rocks and soil using SES methods in three stages?top heading, bench and invert. The collapsed lengths are between 20 m and 277 m. The collapses were re-mined using essentially the same tunnel-ling method with larger excavation profiles to accommodate the designed remedial measures consisting of ground treatment, pre-support and stronger initial support/outer lining required to carry higher ground loads acting in the collapsed lengths. The paper presents information on the collapses and the design and execution of the remedial measures.

Jan 1, 2008

By R. Hildebrandt, K. Cybulski, G. V. Goodman, Z. Dyduch, M. L. Harris, M. J. Sapko

Past research showed that bituminous coal dust remains dry and dispersible in the presence of moisture. Rock dust must disperse with the coal dust to effectively inert a propagating coal dust explosion. Non-treated rock dust readily absorbs moisture, limiting its dispersibility, while anti-caking treated rock dusts can remain dry. The National Institute for Occupational Safety and Health contracted the Central Mining Institute in Poland to conduct large-scale testing in their Experimental Mine Barbara to determine if a treated rock dust can be as effective as non-treated rock dust in attenuating or quenching coal dust explosions under the same experimental conditions. INTRODUCTION One of the goals of the National Institute for Occupational Safety and Health (NIOSH) is to conduct research to reduce the risk of mine disasters and provide workplace solutions to reduce the risks associated with accumulations of combustible and explosible materials; the most common form of which is the generation of coal dust during the mining process and its subsequent distribution downwind. Dispersible rock dust is a primary defense for preventing coal dust explosion propagation in underground coal mines, and its properties are defined in 30 CFR 75.2. “Pulverized limestone, dolomite, gypsum, anhydrite, shale, adobe, or other inert material, preferably light colored, 100 percent of which will pass through a sieve having 20 meshes per linear inch and 70 percent or more of which will pass through a sieve having 200 meshes per linear inch; the particles of which when wetted and dried will not cohere to form a cake which will not be dispersed into separate particles by a light blast of air; and which does not contain more than 5 percent combustible matter or more than a total of 4 percent free and combined silica (SiO2), or, where the Secretary finds that such silica concentrations are not available, which does not contain more than 5 percent of free and combined silica.” An earlier NIOSH investigation of rock dust revealed two significant concerns with the supply of rock dust to U.S. coal mines: 1) insufficient particles <200 mesh (75 μm) and 2) all rock dusts when wetted and dried formed cakes and were not easily dispersed with a light blast of air (1). Past research by the U.S. Bureau of Mines and others showed that bituminous coal dust remains dry and dispersible in the presence of moisture (2). Rock dust must also be dispersible in concert with the coal dust to effectively inert a propagating coal dust explosion (3, 4, 5, 6). Non-treated rock dust, however, readily absorbs moisture, limiting its dispersibility, while a rock dust treated with long-chain fatty acids (such as stearic acid) can remain dry and dispersible. Stearin-treated rock dust has been used in British coal mines (7) and is commonly used in Polish coal mines.

Jan 1, 2019

By Inoka E. Perera, Robert Hildebrandt, Gerrit V. R. Goodman, Krzysztof Cybulski, Zdzisław Dyduch, Michael J. Sapko, Marcia L. Harris

To prevent coal dust explosion propagations, rock dust needs to be lifted and suspended in the air with the coal dust during an explosion. The addition of anti-caking agents prevents caking of rock dust in the presence of water. Mining and rock dusting processes can frequently create alternating layers of rock dust and float coal dust on mine surfaces. For this test series, a thin layer of coal dust was distributed on top of a layer of either treated or non-treated rock dust in the Experimental Mine Barbara, Poland. The experimental results compare the effectiveness of treated and non-treated rock dusts to attenuate a propagating coal dust explosion initiated with either strong or weak methane explosions. Experimental results indicate that the treated rock dust performs better than non-treated rock dust in arresting a propagating explosion, especially in the presence of moisture.

Jan 20, 2020

By Yasushi Arai

"Among Tokyo Metro’s approximately 200km of subway lines, the Tozai Line that connects Chiba Prefecture and mid-Tokyo experiences congestion of up to 199% at worst and relief of this has become urgent. Therefore, as it is imperative to increase the number of trains operating in the exceptionally congested area from mid-Tokyo going east, a large-scale renovation work is planned between Iidabashi Station and Kudanshita Station that will facilitate turn-back via 3 tracks. While ensuring the safe and stable operation responsible for about 1.35 million passengers daily, this highly difficult work of inner wall demolition and reinforcement of the side walls and floor slabs will only be implemented for 3 hours during late night. This paper discusses large-scale plans to improve turn-back facilities, and the methods of construction therein as an example of operational improvement of a subway network. 1) INTRODUCTION The Tokyo Metro Tozai Line (“Tozai Line”) opened over the entire 30.8 km distance from Nakano to Nishi-funabashi on March 29, 1969. It has the longest operating length of the nine Tokyo Metro lines, and was the first subway line to extend past the borders of the Tokyo Metropolis. Through train services with two other railway companies are available from the Tozai Line. Tozai Line trains join the Sobu Line of the East Japan Railway Company (“JR East”) and the Toyo Rapid Railway Line of Toyo Rapid Railway (“TR”) from Nishi-funabashi Station, and the JR Chuo Line from Nakano Station. The line is structurally distinctive in that 51% of it was built using the open-cut method, 43% of it is elevated and the remaining 6% was built when we used the shield method for the first time 1)2)3)."

Jan 1, 2016

By Michael Schmalzel

Freeport-McMoRan Copper & Gold, Inc. (FMI) will soon begin copper production from the Dos Pobres and San Juan deposits near Safford, Arizona. Ore reserves total 615 M tons grading 0.36% copper, predominantly as chrysocolla. Copper extraction will be by leaching with sulfuric acid. Fluor Canada Ltd. provided EPCM services to design an ore handling and conventional SWEW facility capable of producing a nominal 240 million pounds per year of cathode copper. The ore handling facility will process 114,000 tons per day of ore through three-stage, open-circuit crushing followed by agglomeration and product placement on the permanent leach pad. Stacking of ore on the leach pad will utilize Terra Nova Technologies&apos; "Super Portable" mobile stacking system. The stacking system fleet consists of 13 self- propelled, crawler-mounted mobile conveyor units, each with 72-inch-wide belting and a capacity of 6,800 tons per hour, including ten 250-foot-long portable conveyors, a horizontal feed conveyor, a 285-foot-long horizontal conveyor and a 220-foot-long radial stacker. PROJECT BACKGROUND Project History The Safford Leach Project is located in the Safford mining district in Graham County, Arizona, approximately eight miles northeast of the town of Safford and 170 miles east of Phoenix. The 3,360-acre property is located in the Gila River Valley, immediately south of the Gila Mountains, at elevations between approximately 3,000 and 5,400 feet above sea level. The Safford Leach Project is comprised of the Dos Pobres and San Juan deposits, two of five known copper ore deposits in the Safford mining district.

Jan 1, 2008

By C. P. Siess, S. L. Paul, E. H. Gaylord

Several types of tunnel supports are being investigated experimentally and analytically at the University of Illinois at Urbana-Champaign under the sponsorship of the Federal Railroad Administration, Department of Transportation. The results of work on two types will be discussed here. These are steel sets and continuous, monolithic steel-fiber-reinforced concrete liners. The latter is a model of a short length of liner that might result from a continuous slip-forming operation in a tunnel excavated with a boring machine. Tests have been performed on both types of support and analyses are being developed which will greatly broaden the scope of the test program. The objective of these studies is to improve the understanding of basic behavior of these supports, and to develop techniques for their analysis. The analyses will then be used to perform parameter studies that will lead to more rational procedures for structural design. The tests provide a check on the accuracy of the analysis and demonstrate the overall behavior and modes of failure. Another part of the project is concerned with the interaction of support and medium, and thus prediction of loads for the supports. These studies are presented in greater detail in a recent report (1). A brief outline of results obtained to date are presented in this paper. STUDIES OF STEEL SETS Description of Set Tests The sets tested were of the horseshoe type with a 5-ft radius arch section and 7-ft straight legs. They had bolted joints at the crown

Jan 1, 1974

By Min Chen, Qinghua Liang, Weishan Yan, Yuan Feng, Shigang Wang

Various coal mine robots (CMRs) and unmanned aerial vehicles (UAVs) are implemented to explore unknown mines for improving the safety and efficiency of mining. It is challenging for CMRs and UAVs to achieve accurate positioning due to the absence of the Global Positioning System (GPS), poor lighting conditions, and similar geometric features in complex mine scenes. LiDAR-based localization and mapping methods are more accurate than others, while long-time running in large-scale scenarios will introduce nonnegligible cumulative errors. This study presents a semantic-aided Li- DAR simultaneous localization and mapping (SLAM) with loop closure, which leverages the uniqueness of mine intersection structure to establish stable semantic loop closure. Specifically, we propose a semantic intersection descriptor of translation and rotation invariance, which encodes 3D point clouds of the same intersection from different positions and viewpoints into a unified image. By using the semantic descriptor, we can construct a constant loop constraint when the same intersection is revisited from different directions to reduce cumulative drift. We provide experimental validation using large data sets collected in two large underground mines, namely, a simulated Edgar mine deployed in ROS Gazebo and a public underground mine data set provided by ETH. Experimental results show that the proposed method has higher localization accuracy and outperforms the existing LiDAR-based SLAM strategies.

Feb 1, 2024

By K. L. Boyd

"Can the ever-increasing tonnages of ore and waste being mined today be accommodated simply by using bigger and better crushers? This paper reviews the latest primary crushing and large cone crusher designs. It highlights how—in addition to using the larger crushers now available—maximizing the utilization percentages in each of the four stages of the rock size reduction circuit will assist in meeting the larger production requirements of existing and new mining operations. Its goal is to help consultants and operators select the optimal equipment and custom-designed items in the material handling flowsheet from the mine to the mill, maximizing operating hours per year. INTRODUCTION Are larger crushers the answer to meeting the demands of existing or new mining projects for increased tonnage? Boyd (2002) predicted that larger crushers for primary and fine crushing would be beneficial and contribute to the further development of mineral processing. Larger crushers for primary and fine crushing applications are now available. The rock size reduction process from the mine to the selected milling process facility has not changed since man first broke a rock to get at the interesting mineralization within. The rock size reduction process circuit from the mine to the mill can be summarized in four stages: • Stage 1: Mining (rock breakage and fragmentation) • Stage 2: Pre-screening (scalping) • Stage 3: Primary crushing • Stage 4: Fine crushing (secondary, tertiary and quaternary) Plant throughput and ore delivery schedule will form the basis for flowsheet design and equipment selection. Once the project design criteria and the mine plan have been established, the circuit’s utilization percentage (percentage of hours when the circuit is being utilized) can be optimized for each of the four stages. The mining and process departments are the key stakeholders in the selection of the final comminution circuit, and both departments should be familiar with and contribute to the design of the circuit. This paper focuses on the four stages of a rock size reduction circuit from the mine to the mill, equipment selection, various ore and waste handling flowsheets, and improvements in crusher station design, all with the purpose of maximizing availability and plant utilization percentages. What is a large tonnage? From 1907 to 1914, the American Panama Canal excavated 300 million tonnes of material in 7 years (History of the Panama Canal, Wikipedia). Today’s large mining operations can move the same material in 10 months, using large crushers or multiple crushers for ore processing and large crushers and a mixture of truck haulage and conveyors for handling the large waste tonnages. Some examples include:"

Jan 1, 2017

Semiautogenous (SAG) ball mills are being increasingly used today for the coarse grinding of a range of ores, including gold, copper and iron. Larger mines are demanding mills with larger throughputs. This has led to some remarkable developments in mill diameters and installed powers. Conventional design principles - mills with trunnion bearings - have reached their limitations. This article describes one SAG mill with a slide-shoe arrangement and Krupp Polysius&apos; Combiflex twin drive. In August 1997, the world&apos;s largest SAG mill with a slide-shoe arrangement was commissioned in Queensland, Australia, operating as a wet mill. The inside diameter is 10.4 x 5.1 m (34 x 17 ft) effective grinding length. The 1.36-ktlh (1,500-stph) SAG mill is driven by two Combiflex drives (twin drives with 2 x 5,500-MW or 7,375-hp installed motor power) in conjunction with a girth gear (outside diameter 11,890 mm or 468 in.). Commissioning of the SAG mill was completed with no notable technical difficulties. The plant runs continuously except for planned maintenance stoppages and process-specific reasons. As this article is written, the machine has been in operation for about 8,000 hours without major problems.

Jan 1, 1998

By E. Alan Haley

Accurate and economic control of line and grade on long tunnels, large structures, excavations and waterways, has been a problem to surveyors and engineers for decades. The conventional method of surveying, incorporating a level, transit, and a number of surveying technicians, has proven, in the past, to be a very expensive and time-consuming operation. Alignment with a laser has solved most of the problem. Figure 1. With the advent of the Perkin-Elmer Model 5620 Construction Laser, use of laser light is now both dependable and economically feasible for unlimited applications in modern construction and surveying. The laser projects a continuous, narrow red beam of brilliant light, providing a constant alignment reference, and will not interfere with operations.

Jan 1, 1968