Search Documents

By Levent Ozdemir, Robert J. Evans, Russell J. Miller, William Sharp

This paper describes the specifications and capabilities of a 6 ft (1.83 m) diameter laboratory rotary cutting machine which was designed and fabricated under a Bureau of Mines (USBM) contract awarded to the Colorado School of Mines (CSM). The machine will be used for carrying out research and development programs aimed toward improving the design and operation of mechanical tunnel, raise and shaft boring equipment.

Jan 1, 1983

By Wern-ping Chen

To mitigate and control the combined sewer over-flows from 17 outfalls in Detroit, MI, three outfalls in Dearborn Heights, MI and eight outfalls in Redford Township MI, the Detroit Water and Sewerage Department (DWSD) completed the preliminary design of a storage tunnel in 2005. In 2006, a final design revised the alignments and the inside diameter (ID) of the tunnel. The revised tunnel system includes an 11.28-km (7-mile) 9.14-m (30-ft) ID tunnel, a 24.4-m (80-ft) ID pump station, two work shafts about 15.2-m (50-ft) ID each and 14 drop shafts with various IDs. A small portion of combined sanitary and storm sewers serve the majority of the Rouge Valley water-shed. This includes Detroit, MI and most of the western suburbs. The Northwest Interceptor (NWI), that extends between Eight Mile Road and Ford Road and roughly parallel to the Rouge River, intercepts sanitary sewage and some wet weather flows from trunk sewers in the tributary areas for transport to the wastewater treatment plant (WWTP) for treatment. During extreme storm events, when the capacity of the NWI is exceeded, the excess combined sewer and overflow (CSO) over-flows into the Rouge River through 17 outfalls to local rivers. The purpose of the Upper Rouge Tunnel system (URT) is to capture and significantly reduce the uncontrolled CSO from these 17 outfalls in Detroit, three outfalls in Dearborn Heights and eight outfalls in Redford Township. When implemented, the

Jan 1, 2007

By R. Mathur

Cu isotope fractionation in low-temperature aqueous environments has been well documented. Here Cu fractionation was applied to two distinct, yet related, mining problems. First, an exploration geology application, where copper isotope fractionation was measured in oxidized leach caps, chalcocite enrichment blankets and hypogene mineralization in three porphyry copper deposits located in the southwestern U.S. Cu isotope patterns exist in a vertical distribution within the mines, coupled with distinct relationships with the Cu grade. Second, a hydrometallurgical application, where copper isotope fractionation was measured in leach fluids, feed and residues from a quick leach test (QLT) on Cañariaco, Peru ores. The results indicate the relative proportions of the minerals providing Cu during leaching. Interpretations of the QLT test measurements indicate covellite is the dominant ore mineral providing Cu during leaching. Both applications clearly demonstrate the use of the Cu isotope technique to understand low-temperature aqueous processes involving copper.

Jan 1, 2012

By T. McCallum, B. Wellbrook, T. Ratnaweera

"Pressure oxidation (POX) leaching of copper (Cu) concentrates continues to be explored as the next generation of leaching processes to sustain existing Cu Solvent Extraction/Electrowinning (SX/EW) operations as easily leachable ores become scarcer. The leach liquors produced, particularly from total pressure oxidation, contain elevated concentrations of Cu and acid, making solvent extraction processing more challenging. Addressing this challenge will require innovative processing techniques and continuous improvement to be successful in achieving satisfactory physical and metallurgical performance in the SX plant. The ability to efficiently process these feeds via SX plays an important role in the continued success of POX technology. Characteristics of a concentrate leach pregnant leach solution (PLS) are discussed, along with best practices that should be considered for processing by SX. Findings discussed in this paper will shed light on ways to reduce process risk and bring additional improvement to the industry with minimal change to the SX plant. INTRODUCTION Hydrometallurgical processing of copper concentrates continues to gain interest from the industry. Treatment by smelting and electro refining continues to dominate, accounting for ~80% of global copper production, but is faced with its own challenges. The case for increased hydrometallurgical processing has been discussed as high grade ore deposits are diminishing, capital costs for smelting are high, and the environmental aspects present challenges for sustainable practice. The hydromet copper industry is also turning a corner as easily leachable copper oxide deposits are depleting, and excess SX-EW capacity exists in certain regions. The transition to hydrometallurgical processing of copper concentrates will take a bit of effort as leaching of copper sulfides is difficult and byproduct credits must be considered. Various POX leaching processes have been studied and proposed to the industry as viable practices. Of the many processes, commercial use has been practiced with the Mount Gordon Copper Process, total and partial pressure oxidation by Freeport-McMoRan at their Bagdad and Morenci, Arizona complexes, the Sepon Copper Process in Laos, and the bioleach BIOCOP™ process in Chile. The experience related to the current paper centers around Cu concentrate leaching performed by Freeport McMoRan (known as CLP). The patented process was developed as an alternative to smelting and refining in 1998. The technology applies to both molybdenum and copper concentrates. Commercial CLP research and development began with Phelps Dodge in 1999 to 2001. The first commercial plant was commissioned in 2003 at the Bagdad operation. Initial operating conditions of the Bagdad CLP were under high temperature conditions before converting in 2005 to medium temperature conditions. In 2007-2009, the CLP technology was commissioned in Morenci, operating medium temperature and high temperature lite conditions until shutting down due to the economic downturn. The Morenci CLP restarted operation in April 2015 due to acid production benefits for the Morenci leach operations. Renewed solvent extraction test work initiated well before restart and has been an ongoing focus for further SX plant optimization."

Jan 1, 2018

By Richard J. Ebens

The trace element geochemistry of the cherty, clay-rich carbonate residuum. Covering much of southern Missouri and adjacent parts of Arkansas was investigated during the early 1970's as part of a statewide geochemical survey of Missouri-1/2/3 The study was environmentally oriented and focused on the character of the "natural' geochemical environment of the state. A great deal of effort was made to collect samples that would represent the geochemical variability of the near-surface environment in an unbiased way. In general, this was accomplished by use of randomization procedures in both collection and analysis. Most of the sampling sites were selected randomly to prevent personal bias from entering into sample selection. In the laboratory, samples were analyzed in a randomized sequence to circumvent the effects of any systematic bias that may have entered into the laboratory procedures. Several residuum samples contained 1 000 parts per million (ppm) or more of Pb, Zn and Ba. All these samples were collected in Washington County in or near the barite district. The frequency distributions shown in figure 1 indicate just how unusual the residuum in Washington County is with regard to these three metals and copper. The shaded parts of the histograms represent the samples from Washington County. The histograms are based on analyses of 141 samples from 38 localities scattered over the subcrop of the Cambrian and Ordovician Formations of southern Missouri and northern Arkansas. Eight localities were selected randomly from over each of four bedrock units--Bonneterre Dolomite, Potosi and Eminence Dolomites, Roubidoux Formation, and the Jefferson City, Powell and Cotter Dolomites. Six localities were selected randomly from over the Gasconade Dolomite. The geochemical "background" for these elements in residuum is defined by samples from outside of Washington County (unshaded part of the histogram); lognormal distribution curves have been fitted to the corresponding parts of each histogram. Clearly, these lognormal models (curves) describe well the background

Jan 1, 1977

By John P. Cummings

Glass is the most unique substance which man has made. It is understood that Phoenician sailors playing on the beach in Mesopotanmia around 12000 BC, produced glass by the fusion of sand and soda in their campfire. Glass is unique for many reasons. However, let us consider the following. It is made of materials which are opaque and yet glass can be translucent, transparent, or opaque. It can be as soft as cotton or stronger than steel. It transmits light readily and yet is totally impervious to gases and liquids. It is chemically an inert, creates very little pollution in its manufacture. It is made of the most abundant raw materials on earth. It is readily recyclable and has little pollution in its disposal. Glass containers are made principally from sand (that is, silica), soda, which is sodium carbonate, and lime, which is calcium carbonate, plus decolorizers or colorants and cullet. The proportion of cullet, broken glass, in most glass tanks today is roughly 10 to 20% of the glass product. In most cases, the cullet used in the plant is glass from off-ware, or broken ware, which is a waste product within the plant. Cullet has the following advantages. It contains all of the raw materials normally used in a batch. It tends to melt at a lower temperature than batch, thus saving some fuel, and, finally, by forming a crust above the normal melting system, there is a tendency to cut down air pollution.

Jan 1, 1975

By Len Harris

Webster?s Dictionary describes culture as: ? The totality of socially transmitted behavior patterns, arts, beliefs, institutions and all other products of human work and thought typical of a population or community at a given time. ? A style of social and artistic expression peculiar to a class or society. ? Intellectual and artistic activity. ? The art of developing the social, moral and intellectual facilities through education. The authors have nearly 100 years of combined experience in the mining industry working with and consulting to mining companies and companies engaged in the supply of goods and services to the mining industry worldwide. In this report, they present their experiences and ideas on the importance of cultural aspects in the successful development and implementation of mining ventures. Their suggestions on how to handle culture shock will be of interest to expatriate managers, operators, social workers, and engineering and construction personnel posted to overseas operations, as well as to nationals posted to other parts of their own country.

Jan 1, 2008

By M. Arias

"An attractive foreign investment legislation, an anti-mining framework in the jurisdiction where a head office is located, the geographical location of the mineral resources, a country that offers the technology needed by the industry for its operations -- these are some of the many factors that make mining and mineral exploration a global business. It is precisely in the complexity of this new era of globalization and market environment, that sustainability initiatives are challenged. Responsible management of mineral exploration and mining is no longer defined by the use of efficient technology and resource management. Sustainability is not only a report compliance exercise or a green revolution. Sustainability is like any business, a long term profitable proposition. This new approach encompasses four pillars: social, economic, environment, and culture. This new approach connects humans and corporations; it is the way to engage, respect and improve relations with the people with whom we work and our neighbours."

Jan 1, 2011

By Danforth R. Hale

The pressure of military use of quartz resonators led to efforts to Grow high, grade quartz crystals in Germany and in Great Britain during 19)3-25, and was responsible for a series of U.S.A. Signal Corps contracts beginning in 1946 with the Clevite Corporation (as the former Brush Development Company), Bell Telephone Laboratories, Antich College, and others. The technique of growing crystals from the melt, such as KI, NaBr, was already commercially inuse Quartz could not be so grown, since its utility depends on the form stable below 573°C, and, even if it could be grown from an extraordinarily viscous melt, the higher form passing through this transition becomes twinned. Again, several crystals were being grown commercially from water solutions; quartz, however, is listed in the common literature as being insoluble in water. Fused quartz, or vitreous silica, was chosen as raw mater¬ial by the European experimenters because of its thermodynamically lesser stability than quartz, and various alkaline solutions were tried for the purpose of enhancing the solubility.

Jan 1, 1964

By Steve Kral

In the United States, the U.S. Environmental Protection Agency (EPA) is set to implement its Tier 2 air quality standards governing high-horsepower, off-road diesel engines. The regulations take effect in January2006. In Europe, similar standards, called Stages, are due to take effect about the same time. And other markets, such as Japan and Australia, have their own standards on tap. Tier 2 standards will further reduce the amount of nitrogen oxide (NOX), sulfur dioxide (SO2), diesel particulate matter (DPM), carbon monoxide (CO) and hydrocarbons off-highway diesel engines are allowed to emit. And even more restrictive Tier 4 standards are due in 2011. The upshot is that operators of high-horsepower engines, particularly in mining, will begin using in their new off-road haul trucks, excavators, shovels and other mining machines diesel engines that are designed to meet these more stringent standards.

Jan 1, 2004

By G. B. Misra

Attempts have been made during the last three decades to establish a correlation between respirable dust dosage and the degree of progression of pneumoconiosis or silicosis amongst mine workers. Fair correlation has been possible only after the Johannesburg Pneumoconiosis Conference established mass concentration of dust in the respirable size range as the true measure of the incidence of pneumoconiosis. The author had established a good correlation between cumulative total respirable dust dosage as well as cumulative silica dosage and the category of pneumoconiosis according to ILO classification at Mufulira Copper Mine. Studies at Hutti also show a linear relationship between the average cumulative dust and silica dosage md the category of pneumoconiosis. However the maximum tolerable cumulative dust dosage for - prolonged exposure is 182 mg month/m3 - at Hutti as compared to 275 mg month/m3 at Mufulira. Similarly the maximum tolerable silica dosage for - prolonged exposure is Only 35 mg month/m3 at Hutti as compared to 55 mg month/m3 at Mufulira. The TLV for dust concentration at Hutti works out at 0.6 mg/m3 compared to 1.1 mg/m3 at Mufulira and the TLV of silica concentration at Hutti is 0.117 mg/m3 compared to 0.25 mg/m3 at Mufulira. The Hutti figure is however, closer to the TLV of 0.1 mg/m 3 recommended by ACGIH.

Jan 1, 1987

When multiple mines operate in an area there are social, economic and environmental impacts which cumulate over space and time. These impacts require special attention. A collective approach is required to identify, assess and manage them. No assessment of sustainability of mining can be considered complete without accounting for cumulative impacts. This paper proposes a framework and typology to deal with cumulative impacts and tests this in a coal mining area in NSW Australia.

Jan 1, 2007

By Marshall A. Koval

The future of mining in the United States is in question. The cumulative effects of federal, state and local environmental legislation threaten its survival as the cost of compliance skyrockets. Legislation has created pol ari zat ion between government and industry followed by court action, further increasing costs and delays on permitting and remediations. Regulations often call for excessive and rigid requirements that result in unrealistic compliance goals costing tens of millions of dollars. The costs often exceed the value of the remedy. A growing concern is that proper scientific methodologies and engineering practices are being sacrificed because of political and public pressures.

Jan 1, 1991

By Enrique Hermana, Raymond F. Dalton, Raymond Price, Barry Hoffman

Introduction Chloride leaching of sulfidic ores has been known about for 100 years. It is recognized as a highly efficient process to produce concentrated leach solutions. Despite this, chloride leaching found little practical application until recently because of the highly corrosive nature of concentrated chloride solutions. This situation changed with the advent of modern construction materials such as GRP, polypropylene, butyl rubber, etc. And in the past 20 years, research has burgeoned in the area of chloride hydrometallurgy. The research impetus stemmed from the belief that chloride leaching can provide an alternative to smelters for treating conventional copper concentrates. In addition, chloride leaching was thought to be suitable for on-site refining of copper at small tonnage operations located in remote areas. And chloride leaching was seen as a logical choice for treating unusual or complex concentrates that smelters could not handle. Underpinning these beliefs is the attraction of chloride-based hydrometallurgical processes for sulfidic ores. Sulfur is liberated in the environmentally acceptable elemental form rather than as sulfur dioxide. Consequently, sulfidic copper ores have received much attention. A review of Edmiston in 1984 describes 12 chloride-based processes. All managed to progress past the "laboratory beaker" stage of evaluation. In nine of these processes, copper is recovered electrolytically. Key features of these processes are summarized in Table 1. Table 1 shows that the processes must include a copper solvent-extraction step. Only these processes produce a clean copper electrolyte capable, with no further refining, of directly producing high quality cathode copper. The ICI/Elkem process is the exception here. The rest of these processes use o-hydroxyaryloxime reagents for the solvent extraction of copper and are constrained by the performance of these reagents. This is governed by hydrogen ion concentration (Equation 1). The practical result is that only relatively dilute copper solutions can be treated (Canmet, Phelps Dodge), or careful pH control or adjustment is necessary (Minimet Recherche, B.H.A.S.). This negates one of the attractive features of chloride leaching - its ability to produce very concentrated copper solutions, up to 40-45 gl-1. [ ] In all four processes using o¬hydroxyaryloxime extractants, solvent extraction transfers the copper from the chloride to the sulfate medium. To minimize cross-contamination of the two anions, the loaded organic solvent has to be scrubbed to remove the chloride ion. This represents an additional complication in the solvent extraction circuit. And it

Jan 1, 1988

By I. Iwasaki, T. Fujuita

The removal of phosphorus from steelmaking slags is essential for recycling such slags to blast furnaces for recovery of their manganese, iron, and lime contents. Phosphorus is mainly concentrated in the dicalcium silicate phase of the slags (Fujita and Iwasaki, 1988, 1989; Suito, et al., 1977). Slow-cooling of steelmaking slags in an air atmosphere increased the grain sizes of constituent minerals; however satisfactory magnetic separation results could not be attained because of the close association of a strongly magnetic ferrite phase with dicalcium silicate (Fujita and Iwasaki, 1988). Curie point of the strongly magnetic ferrite phase in the slow- cooled steelmaking slags was investigated and an attempt was made to separate the phosphorus-bearing dicalcium silicate phase in ground slag pulps heated to a temperature exceeding the Curie point. Materials and methods Slag samples, heated to its fusion temperature of 1370°C and slow-cooled in an air atmosphere, were ground dry to -90 µm (about 170mesh) in a ring grinder. The ground sample was pulped to 1% solids in distilled water using 1 kg/t sodium hexametaphosphate as a dispersant and separated in a Sala high gradient magnetic separator, Laboratory Model 10-15- 20B, using a 100-mesh expanded metal matrix and 300 m/h flow rate.

Jan 1, 1990

By Thomas B. Dellinger

Since 1950, rotary-drilled, large-diameter holes, "big holes", with depths to over 300 feet and diameters of over 30 inches have become numerous and widespread. Fifty such holes have been drilled for access shafts to LPG mined caverns, Over 70 holes have been drilled for various other commercial activities. Over 150 holes have been drilled by the AEC for atomic testing purposes. These holes have ranged up to 300-inch diameters with 1600-foot depths, 120-inch diameters with 570-foot depths, and 72-inch diameters with 4800-foot depths. Equipment is now available to drill a wide range of ?big holes? for varied requirements. At least a dozen drilling contractors are participating or have participated in the drilling of "big holes". The accompanying tables show pertinent historical, technical and economic data on over 250 holes. The illustrations to be presented concurrently with this paper show the various equipment and accessories now in use. (See Appendix I for captions of illustrations.)

Jan 1, 1966

By Wesley W. Eckles

Microcomputer technology has begun to revolutionize petroleum engineering. Petroleum engineers' use of relatively inexpensive personal computers (PC's) is likely to continue expanding rapidly. Since 1982 SPE's Microcomputer Applications Committee has developed a Society-wide users group, a bi-monthly newsletter (MICROCOMP NEWS), an SPE Short Course, a hardware and software distribution program, and a world wide electronic network (SPE NET). The purpose of this paper is to share SPE's experience in creating a dynamic program for meeting the individual member's need in the application of microcomputers to petroleum engineering. My hope is that this will encourage other engineering and scientific organizations to provide similar programs for their members.

Jan 1, 1985

By P. J. Bethell

This paper reviews current fine coal cleaning circuitry, including water washing cyclones, tabling and froth flotation. It goes on to examine possible future beneficiation based on emerging technologies. Circuits considered include those incorporating spirals, fine heavy medium cycloning, hydrosizers and column flotation.

Jan 1, 1988

By Ian McFeat-Smith

Despite a present, short-term economic recession, a remarkable enthusiasm exists in Hong Kong for building infrastructure including major tunnel projects. This paper provides details of current and recent bored tunnel works together with an insight into the impressive list of future underground projects planned by the MTRC,KCRC, Highways Department and Drainage Services Department for the next decade. Risks for each of these works including pipejacking, mixed face and rock tunnelling generally in Hong Kong are also identified. From this is evident that the scale and difficulty of such works continues to increase, requiring the use of more sophisticated methods of construction, the need for better methods of assessing and managing risks and for Government to utilize improved, more equitable Conditions of Contract for such major tunnelling projects.

Jan 1, 2001

By Neal Cochran

I consider it a distinct privilege to be afforded the opportunity of discussing the program of the Office of Coal Research. The principal activities I will be discussing are concerned with projects that fall in the utilization area. I will, to be sure, touch on other activities of the Office of Coal Research but am not equipped to discuss these activities in great detail. Research activities of the Office of Coal Research are conducted on a contract basis with commercial, academic, and non-profit institutions. We do not operate any laboratories of our own but we do maintain a very small staff for technical and administrative supervision of our contractors. We have consistently attempted to interest outstanding, creative, and practical research organizations in our program. We are constantly seeking the imaginative new idea that will materially reduce the cost of mining coal, transporting it, or will process it into a more convenient and useable form. In assessing proposals and in developing our program, we search for the improvements that will develop large-scale new uses for coal or coal products or those that support these new uses.

Jan 1, 1963