Search Documents

By S. J. Parkin, P. Shead

Extraction of coal at Harworth Colliery is undertaken in the Deep Soft seam at roughly 1000m depth where the strata temperature is 42 "C. Production employs the longwall retreating method using high powered mechanised methods to extract coal at a rate of approximately 40,000 tonnes per week from a single face. This paper describes the climatic conditions encountered on a typical district , 6's district, where the initial ventilation set-up was as a typical U-type district which was antitropally ventilated. Under this initial set-up climatic conditions in the intake typically exceeded 30 "C effective whilst in the face area and in the return airway effective temperatures in excess of 32 "C and 33 "C were common . The paper then proceeds to describe the methods employed to attempt to improve the climatic conditions on the district, especially with regard to the coal face and return airways and describes in detail the effects of reversing the district airflow direction, employing homotropal ventilation, on the climatic conditions. The results of this reversal have been dramatic and have resulted in a substantial improvement in the climatic conditions experienced , however problems have been encountered with the control of methane gas since the changeover. The final part of the paper describes the results of computer simulations to analyse the effect of various ventilation designs on the predicted climate for future production districts in order to de- fine a district layout which will produce acceptable climatic conditions in the working zone without the need to use refrigeration techniques and which will improve methane gas control .

Jan 1, 1997

At present the feasibility of developing underground facilities for the storage of a number of products including toxic waste, oil, nuclear waste and low pressure gas is under investigation in e number of countries. A possible method of storage is in large excavations, Preliminary ventilation design work has identified that the climatic conditions encountered within these large excavations are a limiting ventilation pollutant within the ventilation system. This paper examines the design of a variety of sizes of excavation from a ventilation viewpoint. The main phases of an excavations lifetime can be divided into four main phases, these being construction, civil and mechanical fitting, storage, full and sealed. The paper details ventilation design options for the first two phases of e vaults lifetime, giving climatic simulations to assess the likely climatic conditions within the excavations for e number of facility depths. The options for climatic control are given and analyzed by means of climatic simulations techniques. l. INTRODUCTION The feasibility of developing underground facilities for the storage of a number of products is under investigation at present in a number of countries. This paper details a possible design for such a facility where the product is to be stored in large underground excavations. A facility layout has been designed with the aim of allowing concurrent construction and storage operations. Thus from a ventilation perspective the facility consists of two circuits , a construction ventilation circuit and a product ventilation circuit both of which are served by an intake and a return surface connection The construction and storage circuits are considered as independent of each other , any interaction in the form of leakage must be from the construction to the storage circuit. From the facility design a ventilation network was developed to assess the ventilation requirements of the facility. In analyzing the pollutant loads for the construction circuit two pollutants were recognised to be critical to the ventilation design , these being diesel exhaust fumes and heat end humidity. In this paper ventilation design options for the construction and civil and mechanical fitting phases of the excavations are analyzed by means of climatic simulation and options for climatic control within the vaults are outlined . 2. FACILITY DESIGN A schematic diagram of a facility design is illustrated in Figure 1. There would be two distinct ventilation circuits , one to service the construction operations and the second to serve the storage operations which occur concurrently with construction , the circuits are separated by ventilation bulkheads . Access to the facility for intake air is provided by two drifts, one to serve each circuit. Two shafts act as returns to surface. The facility consists of two distinct zones for the storage of two types of product. One type is to be stored in smell linear excavations. The second zone is for the storage of a second product in larger excavations. The maximum cross-sectional area and perimeter for the smell linear excavations are 456.25 m2 and 83.2 m, while for the larger excavations they are 440.1 m2 and 86.4 m. Excavation construction consists of three phases: 1. Initial pilot tunnel development between main intake and return to provide through flow ventilation. 2. Enlargement to produce the required finished cross-section. 3. Civil and mechanical engineering work to fit out the excavation ready for storage. It is proposed to excavate the excavations using drill and blest methods utilising diesel equipment. Spoil is to be transported to surface by a conveyor belt system. At any one time the maximum number of working places requiring ventilation will consist of ; 3 storage sites, 2 excavations under construction, 2 excavations undergoing civil and mechanical fitting. [ ]

Jan 1, 1993

By William G. Doepken

After 15 years of production, 91 Mt (100 million st) of ore mined and nearly 227 kt (500 million lb) of molybdenum produced, Climax Molybdenum Co.'s Henderson Mine and Mill are being modernized as a new mining level is brought on line. The $40 million investment in mine development and plant modernization positions the Henderson complex as one of the largest, low-cost primary molybdenum producers for the next 15 years. Henderson history The Henderson Mine and Mill facilities are located on the east and west flanks of the Continental Divide about 80 km (50 miles) west of Denver, CO. The underground mine and surface mill sites are linked by 16 km (10 mile) of railroad tunnel and 8 km (5 mile) of surface trackage. The mine, railroad and mill were built between 1968 and 1976 at a cost of $500 million. Each has operated at various levels of production over the past 15 years. The Henderson Mine was originally developed using a highly mechanized, panel caving mining system. Over the past 10 years, mining methods, equipment and railroad operations have been improved to position Henderson as one of the most productive and lowest cost underground mining operations. At the same time, the mill and concentrator facilities were upgraded to reduce costs and improve product quality. During this time, manpower was reduced from 2000 to 560 employees. These 560 people increased productivity to 54 t (60 st) per total manshift. They reduced operating costs by 50%. And they dramatically improved safety performance. However, as the 1990s approached, the modernization of the Henderson mining and milling complex and the development of the new 7700 mining level became the primary goals to guide Henderson into the 21st century.

Jan 1, 1991

By J. V. Ghelarducci, M. A. Sharpe, D. G. Chedgy

This article presents a novel design, called the Climax, High Capacity Processor (HCP), for pre-combustion cleaning of coal. This design is particularly suitable for the plant capacities of 400 ~ 660 TPH. The HCP is different from the conventional designs with an equivalent throughput in three major aspects: 1) the use of one large capacity HM cyclone to separate coarse and intermediate raw coal in a single circuit; 2) the elimination of the conventional secondary magnetics recovery system by use of the high efficiency Climax, magnetic separators; 3) the use of "single line" piping with a minimum requirement of ancillary devices. In comparison with conventional designs with similar capacity, the HCP plant costs much less in capital investment, operation and maintenance.

Feb 24, 1997

By D. G. Chedgy

This article presents a novel design, called the Climax High Capacity Processor (HCP), for pre-combustion cleaning of coal. This design is particularly suitable for the plant capacities of 400 -660 TPH. The HCP is different from the conventional designs with an equivalent throughput in three major aspects: 1) the use of one large capacity HM cyclone to separate coarse and intermediate raw coal in a single circuit; 2) the elimination of the conventional secondary magnetics recovery system by use of the high efficiency Climax magnetic separators; 3) the use of "single line" piping with a minimum requirement of ancillary devices. In comparison with conventional designs with similar capacity, the HCP plant costs much less in capital investment, operation and maintenance.

Jan 1, 1997

In the grand scheme of things, the 9.5-t (21,000-lb) shipment of molybdenum concentrate that left Freeport-McMoRan?s Climax Mine site on May 10, 2012 was not unlike the thousands of others that have been hauled away from the site during the last century, except for the fact that this shipment marked the official rebirth of one of America?s greatest mines. For nearly two decades, 17 years to be exact, there was no production from the mine that was once the largest underground mine in the world and was so important to the Allies? effort during World War II that it was assigned the highest priority of any mine in the United States by the War Production Board. The economic recession in 1980 put an end to the mine?s success, and the Great Recession of 2008 nearly derailed the mine again. But, like the nearby town of Leadville, CO, the mine survived thanks to an investment of more than $700 million by Climax Molybdenum Co., a Freeport-McMoRan company, to bring the Climax Mine back into production.

Jan 1, 2012

By Stephen M. Voynick

Two hours driving time west of Denver, CO and 21 km (13 miles) north of Leadville, Bartlett Mountain rises 4,065 m (13,337 ft) high in central Colorado's Tenmile Range. Bartlett Mountain is one of Colorado's most recognizable peaks, especially when the late afternoon sun casts a surreal, reddish light across its most prominent feature - the Glory Hole. This is a gaping, half-mile-wide, 245-m- (800-ft-) deep crater. Created by subsidence from 60 years of massive underground mining, the Glory Hole is a monument to the Climax Mine, one of the great achievements in American mining and metallurgy. For most of this century, the name Climax has been synonymous with brilliant mining engineering, innovative metallurgical research and entrepreneurial promotion of a once-obscure metal - molybdenum. Climax overcame an array of economic, technological and social problems to become a model for underground development of massive deposits of low-grade ores. It is one of the few mines in the world where cumulative production is measured in the billions of dollars. The Climax mineralization was emplaced 30 million years ago. Magmatic intrusions formed a large, mineralized stockwork within the granite country rock of Bartlett Mountain. Associated hydrothermal events forced superheated metal- and quartz-rich solutions through fracture zones, silicifying the country rock and depositing huge amounts of molybdenite, or molybdenum disulfide. The mineralized rock, a light gray, finely crystalline, silicified granite, is laced throughout with blue-gray quartz veinlets containing molybdenite. Although the richest ores graded only about 1% molybdenite, the Bartlett Mountain deposit contained more than 2.7 Mt (3 million st) of elemental mo- lybdenum.

Jan 1, 1997

By John C. Gould

GENERAL DESCRIPTION The Climax mine is located 161 km (100 miles) southwest of Denver on Fremont Pass astride the Con¬tinental Divide. Climax employs 2800 people to pro¬duce 42 670 t/d (47,000 stpd) of molybdenum ore. The Storke level, the main underground level, produces 19 970 t/d (22,000 stpd); the 600 level, the lowest ac¬tive underground area, produces 7260 t/d (8000 stpd); and the open pit presently produces 15 430 t/d (17,000 stpd), Fig. 1. A panel caving method is possible because of the favorable geology and geometry of the Climax ore body. Geology The Climax deposit is composed of three separate ore bodies formed in a massive Tertiary stockwork which penetrates Precambrian granites and schists. The ore bodies are elliptical in plan with overall dimensions of 914 x 1219 m (3000 x 4000 ft). In section the ore bodies are arcuate with an overall height of 457 m (1500 ft), although the depth is not firmly ascertained. Ore grade decreases rapidly into a highly siliceous cen¬tral core and more gradually toward the outer bounda¬ries of the deposit. The mineralization is relatively continuous in the ore zone and contains few dilution-causing waste inclusions. Molybdenite is contained in pre-ore fractures which were largely recemented during the three mineralization pulses. Postore fractures, with a spacing of a few inches to several meters (feet), render the deposit amenable to caving when it is undercut. The peripheral rock caves similarly to the ore, but the central core is competent and is difficult to cave. Caving Feasibility Successful caving action requires an undercut area of approximately 122 by 122 m (400 by 400 ft). When the undercut area exceeds this minimum distance, the arching effect is lost, and the ore column collapses. Ore extensions from the main cave area less than 122 m (400 ft) wide usually cannot be caved. Waste or low¬grade areas within the deposit can be left if they are large enough to carry weight around openings passing through them. Experience indicates that these areas should be over 30 m (100 ft) in length and width. Smaller unprofitable units of waste, such as postore dikes, are mined to avoid weight problems and result in ore dilution. Successful caving and ore recovery are dependent upon timely ore removal from the undercut zone because columns of immobile ore inhibit caving and concentrate weight onto the underlying workings. Climax experience indicates that a finger (drawpoint) spacing* averaging 10.4 m (34 ft) yields an excellent caving action and a 92.5% ore recovery at the estimated grade. An additional 15% of the ore is recovered-at a diluted grade (Fig. 2). Mine Layout The slusher drift is the primary production facility (Fig. 3). The ore is undercut and caved into the fingers,

Jan 1, 1982

By R. E. Musgrove

At the present time Climax Uranium Company recovers vanadium oxide from carnotite type uranium ores in the mill at Grand Junction, Colorado, The flowsheet of this mill is shown in Figure I. Vanadium is solubilized by a salt roast of the slime fraction of the ore and dissolution is accomplished by a water leach. The metal is precipitated from the pregnant liquor as sodium polyvanadate by heating to boiling and adjusting the pH to 3 with sulfuric acid. The sodium polyvanadate, commonly called, "red caken, is filtered, melted, and cast into thin flakes. This fused flaked vanadium oxide is the material which is packaged for sale. Fused vanadium oxide, marketed by Climax, contains approximately 87% V205, 7% alkali oxide, 0.08% sulfur, 0.03% phosphorus, and less than 0.5% Insoluble. This material is of a lower grade and has a higher alkali oxide content than other vanadium products offered for sale at this time. A typical analysis of a high grade vanadium oxide currently offered for sale by another company is 98% V205, 1 - 2% alkali oxide, less than 0.05% sulfur and less than 0.2% Insoluble. The only reagent consumed in the precipitation of the sodium polyvanadate is sulphuric acid. The total reagent cost is 0.58 cents per pound of vanadium oxide produced.

Jan 1, 1958

By Steve Kral

The Clinton administration’s policies toward the environment have the mining industry on the defensive. The president and US Secretary of the Interior Bruce Babbitt continue to bypass Congress in their efforts leave an environmental legacy when they leave office in a year. So the mining industry must take its case to the public. And the public seems willing to listen if the industry is willing to tell its story, according to US Rep. Chris Cannon (R-UT). Cannon was one of the keynote speakers at the105th meeting of the Northwest Mining Association, in Spokane, WA. The conference, held in early December, attracted about 2,400 people and more than 200 exhibitors

Jan 1, 2000

By Z. Rogovin

A Knowledge of the amount of time the material spends in a continuous mill in a closed-grinding-circuit is essential for circuit performance analysis and scale-up design. A convenient method for acquiring this information involves the use of tracers in residence-time-distribution (RTD) experiments. In a typical wet process the RTD measurements are usually done by injecting a pulse tracer into the mill inlet and detecting it in the circuit exit. In this article a simple to use mathematical method for the calculation of the closed circuit material residence time in the mill is developed. Using this method there are no restrictions on the location of the tracer injection or detection points. Any convenient location in the closed circuit can be chosen without affecting the simplicity of the method. This method also enables the calculation of the degree of mixing in the mill. The use of this method for the analysis of impulse response data obtained from several commercial grinding circuits is presented.

Jan 1, 1986

By J. A. Herbst, Z. Rogovin, Lo. Y. C., K. Rajamani

Knowledge of the amount of time material spends in a continuous mill in a closed grinding circuit is essential for circuit performance analysis and scale-up design. A convenient method for acquiring this information involves the use of pulse tracers in residence time distribution (RTD) experiments. In typical grinding circuit experiments, RTD measurements are done by injecting a pulse tracer into the mill inlet and detecting it in the circuit exit. In this article, an easy mathematical method for calculating mean residence time and the degree of mixing of material in a mill present in a closed grinding circuit is developed. There are no restrictions on the location of the tracer injection or detection points with this method. Any convenient location in the circuit can be chosen without affecting the residence time distribution measured. The analysis of impulse response data obtained from several commercial grinding circuits using this method is presented.

Jan 1, 1988

By Joseph L. Petrillo

In July 1997, Kvaerner Environmental signed a unique contract with Echo Bay Alaska called the Transfer Risk and Accelerate Closure (TRAC). The contract called for Kvaerner to assume the responsibilities and obligations associated with closeout of the Alaska-Juneau (A-J) Mine. Kvaerner is an international engineering and construction company with global interdisciplinary experience in the mining industry and environmental remediation. Echo Bay’s requirements called for Kvaerner to: •Provide a fixed price for closure with no change orders. •Negotiate, prepare and implement a final closeout plan as outlined by Echo Bay. •Complete a closure program that exceeded current regulatory requirements. •Improve, expand and maintain a proactive public and community relations program. •Hire Echo Bay employees where possible. •Provide adequate performance guarantees and judicial relief of environmental claims.

Jan 1, 1999

By T. Braun, J. Parker

On June 25, 1999, BHP Billiton (BHPB) announced the suspension of operations at the BHP Copper Inc.(BHP) San Manuel copper mine in Pinal County, Arizona. Subsequent to this announcement, BHPB aggressively pursued a number of alternatives for the underground mine and open pit facilities, including continued curtailed operations, sale to a qualified mining operator and closure of the property. After consideration of these various alternatives over a 2.5-year period, BHPB announced final closure of the mine site on January 15, 2002.This paper describes how the BHPB charter and HSEC policy apply during the closure process.

Jan 1, 2004

By Alan Dahlstrand

The Jamestown Mine is a 6.3-kt/d (7000-stpd) open-pit gold mining operation located in the central portion of California's historic Mother Lode district. Most early production from the Jamestown area occurred in underground operations from 1906 through 1916. Pit production began at Jamestown in early 1987 and continued until July 1994. Although additional mineral resources existed, they were deemed to be uneconomic. About 23.3 t (750,000 oz) of gold were produced from pit operations, compared to 31 t (100,000 oz) from early underground mining. Recent operations at Jamestown included two open pits, a flotation mill and a flotation tailings facility. Flotation concentrates were produced in Jamestown and shipped to Yerington, NV for cyanide leaching in a carbon-in-pulp (CIP) circuit.

Jan 1, 1995

By J. J. Antony

As the first wave of precious metal heap leach closures and reclamation projects occur, a number of companies are being hit with costly surprises. While this paper refers specifically to U.S precious metal projects, it could be conceptually directed at copper leach operations and acid rock drainage (ARD) problems on an international basis. ARD is Mother Nature's version of heap leaching, only with different products and timing. Although many precious metal deposits tend to be small in comparison with some base metals systems (porphyry copper deposits), adjacent or nearby discoveries have extended the operating lives of numerous precious metal mines. Now, depleted reserves, several years of relatively depressed precious metals prices and some properties with technical difficulties have resulted in numerous mine closures. As a result, our industry is getting a diverse and comprehensive initial look at mine closure and final reclamation. The situation has been further complicated by the evolutionary trend in regulations and their enforcement and increasing public and political awareness of all environmental issues. Concurrent (proactive) vs. deferred (reactive) reclamation and a realistic early appraisal of ultimate reclamation and closure requirements, not just regulatory compliance, need to be a part of project design. The U.S. and Canada are the current fertile testing grounds and have set the design, regulation and closure standards for the next wave of operations in Latin America, the CIS (?), etc.

Jan 1, 1994

By R. C. Ford

The advent of solvent extraction-electrowinning (SX-EW) technology for recovery of copper from low grade oxide ores has extended the operational lives of many historic mines in the western United States, and made many other orebodies economically viable worldwide. Many of these operations are mature and face closure within the next decade, depending on market conditions. Closure of a large copper heap leach operation has not been undertaken, and differs in some important chemical respects from closure of gold leach pads. Challenges for closure include prediction of solution chemistry and draindown characteristics, determining the benefit of cover placement in semi-arid climates and evaluation of solution management strategies once the economics of copper recovery are no longer favorable. This paper discusses issues pertinent to copper heap closure in semi-arid and arid climates, and strategies for their management.

Jan 1, 2000

By M. H. Rauschkolb, J. A. Cremeens

Geotechnical solutions were developed for closure of two historic, remote underground mines in the deserts of southern California. Closure criteria included access closure, minimal site impact, and optimum use of native materials. The closure designs and construction activities incorporated techniques for protecting sensitive biota, particularly bats and desert tortoise. The types of mine openings that were closed include adits, declines, shafts, daylighted stopes, and dugout dwellings. The desert locations permitted implementation of cost-effective closure techniques that relied upon the use of native materials. The strategies and techniques developed for these desert closures are adaptable to other climates.

Jan 1, 2002

By K. Adam

Uncontrolled disposal of pyrite wastes and concentrates comprise a major source of acid drainage in active and abandoned sulphide mines. In this paper, the state?of-the-art mitigation measures implemented for the final reclamation and closure of a pyrite concentrate stockpile at Platia Karra, Stratoni mines, Greece, are presented.

Jan 1, 2002

By D. H. Garcia

The mining industry responded to public concerns about use of cyanide by developing a voluntary certification to allow companies to demonstrate their commitment. The International Cyanide Code (Code) establishes standards for the manufacture, transportation and use of cyanide. Key concepts in closure planning to comply with the Code are to decommission all facilities related to cyanide operations and to provide a financial assurance mechanism for those activities. Code requirements may differ from state-specific regulations, but requirements are based on closure goals for protection of the human health and the environment. Only issues related to cyanide operations are required to be included in decommissioning demonstrations. For example, the disposal method of cyanide solution holding tanks and the cost must be included in the closure plan, but information regarding closure of roads is not required. Closure costs must be based on a third-party contractor as opposed to internal budgets. Compliance with the closure requirements of the Code allows companies to show their stockholders, lending institutions, and the public that their operations are environmentally responsible.

Jan 1, 2010