Search Documents

By Park. D. W., Y. M. Jiang, L. A. Morley, W. Keeton

Underground room-and-pillar mining operations in the Warrior Coal Field in Alabama frequently suffer instability due to soft floors and thinly-laminated immediate roofs. This investigation concerns a mine that was experiencing ground-control problems with weak floor conditions. Several roof falls occurred locally, and as much as 0.6 m (2 ft) of floor heaves have been experienced. The paper presents the results of comprehensive analyses conducted on floor heave, roof sagging, pillar- penetration and floor bearing capacity using instrumentation and numerical modeling.

Jan 1, 1993

By Ronald O. Harma

Iron ore pellets made from concentrates produced from low grade iron ores are the primary iron bearing feedstock for iron making in North American blast furnaces. Steelmakers are demanding increasingly higher quality to provide for improved blast furnace productivity, efficiency, product quality and environmental compliance. Unfortunately, this higher quality iron ore product must be produced from the vast deposits of low grade iron ores that are becoming increasingly poorer in quality with regard to mineral liberation and ease of concentration. Since some of these low grade iron ores require grinding to as fine as 90% -500 mesh (25 microns) for liberation and since more of the silicious gangue and other minor undesirable constituents must be removed to provide the higher quality, we have come to depend on flotation to do the added work. Flotation technology and other preflotation unit operations must improve to meet these increasing demands. In many cases, flotation equipment, reagents and circuit operating performance have improved little during the last two to three decades. Mechanical flotation cells have grown from 14 cubic meters (500 cubic feet) to over 84 cubic meters (3000 cubic feet) to help reduce capital and operating costs; however, flotation metallurgical performance has not improved, Column flotation has only recently shown promise in improving metallurgical performance for iron ore rougher flotation. Previous column flotation success was mainly in scavenger and cleaner flotation steps for treating minerals other than iron ore. Although some new flotation chemicals have been developed for removal of silica and other minor constituents under widely varying mineralogical scenarios, recovery of iron mineral has not improved. The operation and control of flotation circuits have become more challenging because of the increasing workload on flotation. Better sensing, process control and operation of flotation circuits are essential as we go forward. Iron ore upgrading by flotation can be classified into either anionic or cationic methods. Anionic flotation of either iron oxide or silicious gangue is accomplished by collector type, pH control and selective chemical activation . Similarly, cationic flotation of silica or iron oxides is accomplished by collector type, activation and/or pH control. Removal of other minor constituents is achieved by using specialty chemicals under controlled conditions for preflotation, co-flotation or post flotation steps. Generally, anionic flotation is used for floating cleanly liberating crystalline oxidized iron ores such as hematite, specularite and martite. Earthy and hydrated oxides such as hematite and geothite can be upgraded with either anionic or cationic collectors after controlled dispersion of slimes or prior removal of slimes. Anionic flotation of silicious waste can be achieved by calcium activation of silica. For magnetic iron ores small amounts of locked silica particles (middlings) can be removed by cationic silica flotation, which is the only method in commercial use in North America today. Historically the efficiency of these iron ore flotation processes has been restricted by the loss of fine iron particles (minus 500 mesh) to the tailings product. New technology is required to overcome this loss and improve overall flotation performance. Development of technology for more selective separation of silica and other minor undesirable constituents from iron ore will provide both quality and cost benefits to the iron and steel producers. Development of future iron ore production in North America will face stiffer technical challenges. These new and undeveloped iron ore deposits are largely oxidized (non-magnetic) and by nature contain more slimes and other undesirable constituents. Unless other new technology evolves, flotation will be the major treatment process required to upgrade these difficult low grade iron ores.

Jan 1, 1993

By E. Ozberk, J. B. Hiskey, M. J. Collins, B. J. Scheiner, M. E. Chalkley, I. M. Masters

Conventional zinc concentrates generally contain 5 to 10% Fe, while bulk concentrates can contain up to 20% Fe. As a result, the disposal of iron bearing residues is an integral part of zinc refining operations. The quality of iron residues must comply with ever changing and increasingly stringent environmental legislation. Zinc has been recovered from sulphide concentrates by a hydrometallurgical route for almost one hundred years. The disposal of iron was a major difficulty for the industry for many decades and was directly responsible for low overall zinc recoveries. The introduction of the jarosite process in the mid 1960's allowed for the treatment of neutral leach residues and the precipitation of iron in an easily filterable form. Subsequently, three additional iron precipitation processes have found commercial application in the zinc industry: the goethite process; the paragoethite process; and the hematite process. The Sherritt Zinc Pressure Leach Process has been developed for integration with existing roast leach electrowin zinc plants, or as a stand alone facility for the treatment of a wide variety of zinc bearing feed materials. It is essential that these processes allow for the disposal of iron residues in an environmentally acceptable form. This paper describes the integration of the Sherritt Zinc Pressure Leach Process with commercially proven iron precipitation processes. The results of laboratory testwork and data from operating plants are presented.

Jan 1, 1993

By R. T. Richins

Coeur d'Alene Mines Corporation (CDE) is a precious metals mining company. The company's three mining operations are located In Nevada and Idaho. Collectively, these mines (Rochester in Nevada, and the Galena and Coeur In Idaho) produced about 61,000 ounces of gold and more than 7.5 million ounces of silver in 1991. The company is currently planning the development of two major properties; the Fachinal gold-silver project in Chile and the Kensington gold project near Juneau, Alaska. Fachinal and Kensington hold encouraging potential to significantly expand CDE's gold production during this decade. The permitting process for these two distinctly contrasting environmental settings, project design requirements and regulatory/political circumstances provide the basis for a comparative analysis of licensing and permitting requirements, timeliness of the permitting process and costs in the U.S. and Chile.

Jan 1, 1993

By Henrie Henson, Dan Burroughs, Shyi-Shyong Jiang

Jan 1, 1993

By Kenneth R. Miller

ThunderBasin Coal Co. has two mines located in the southern portion of Wyoming's Powder River Basin - the Black Thunder Mine and the Coal Creek Mine. Both are located 60 to 90 kin (37 to 55 miles) southeast of Gillette. The mines are principally located on federal coal leases acquired in the late-1960s. Development plans for the Black Thunder Mine focused on dragline stripping. Environmental considerations, however, made truck-shovel stripping the method of choice when the mine opened in 1976. In 1981, the Coal Creek Mine opened as the first dragline mine in the Gillette area of the Powder River Basin. The regional terrain is flat-lyimg with occasional clinker-capped hills. The mines are located on the Wasatch and Fort Union Formation contact. The coals are Paleocene in age. The deposits are structurally simple, dipping gently to the west. The seams are thick and are classified as sub-bituminous-C. The Black Thunder Mine, with its 21-m (70-ft) 'hick seam, is strategically located in the center of the highest heat value mining area of the southern Powder River Basin.

Jan 1, 1993

By J. Pang, S. Chander

The results of an investigation to characterize the chalcopyrite/solution interface are presented. Several techniques were used, including galvanostatic and steady-state polarization, cyclic voltammetry and impedance spectroscopy. The results show that the dissolution of chalcopyrite was incongruent. Initially, at low potentials (< 0.12 V), iron species were released that led to the growth of an iron-deficient sulfide (IDS) layer (referred to as the "reacted layer" in this paper). Depending on the solution&apos;s composition, the dissolved iron might reprecipitate as a hydroxide layer. In the potential range of 0.12 V < E < 0.23 V, the IDS layer was passivating. In comparison, development of a passivating IDS layer under galvanostatic conditions led to a jump in potential to 0.48 V. The IDS layer began to dissolve at potentials greater than 0.24 V. The dissolved species precipitated to form a product layer in alkaline solutions. Continued oxidation involved diffusion of species through the reacted and product layers. At higher potentials (> 0.48 V), further oxidation led to the dissolution of the copper and sulfur species, with a resultant breakdown of the IDS layer. The changes in surface-coating properties, resulting from various electrochemical treatments, are discussed.

Jan 1, 1993

By F. M. Doyle, P. E. Richardson, E. Peters

A number of studies have attempted to correlate the semiconducting properties of mineral sulfides with their chemical reactivity. Frequently such studies are conducted on polished or abraded electrodes. Defects produced by abrasion may mask the influence of the semiconducting properties of electrodes, e.g., by pinning the Fermi level at the surface or by reducing the lifetimes of photogenerated charge carriers. It is shown that pyrite and galena electrodes have photocurrents that are extremely sensitive to abrasion of the electrodes. On freshly fractured galena surfaces, the space charge layer is readily polarized. Wet-abrasion is shown to produce a relatively thick ptype layer on galena electrodes and this p-type layer has a pronounced effect on the photoresponse. On freshly fractured pyrite surfaces, the Fermi level at the surface is pinned by a surface state. Wet-polishing reduces the magnitude of the photocurrent by over an order of magnitude.

Jan 1, 1993

By J. A. Herbst, K. N. Han, P. B. Queneau, S. W. Asihene

As hydrometallurgy matures as a technology, more of its existing process knowledge will continue to be summarized in the form of detailed mathematical models. This development is happening at a time when major improvements in computer hardware have reduced the cost of computing. The opportunity then exists, through the solution of these process models, to design, control, and optimize hydrometallurgical plants on the basis of the physics and chemistry of its processes and less on empiricism. In this paper, a review of the current capabilities of sensors and phenomenological models for selected hydrometallurgical processes is presented. Future trends, in terms of the control and optimization of hydrometallurgical plants, are then explored. The possibility of simultaneously optimizing plant design and associated process control system performance is discussed.

Jan 1, 1993

By Alex Harrison, Steve Kasper

Various countries around the world have testing and manufacturing standards in place for steel cord belting. These standards are very comprehensive in what they allow the end user to specify, however, their practical significance in terms of belt life is more difficult to quantify. Such testing standards will be briefly reviewed in this paper in relation to the implication for end user expectancy. Since there is no US standard of manufacture, the end user is left with writing their own specifications. In addition, such standards do not address the effect on belt life of manufacturing faults, such as cord plane buckles, or lateral cord movement. Some new technology used to test steel cord belting will be described as an aid to both manufacturer and end user. Specific end user related issues addressed on this paper are: Tracking and belt quality Cord plane irregularities and performance Cord size and belt life Cord fatigue and testing

Jan 1, 1993

By R. D. Schmidt, M. J. Friedel

Unsaturated permeability and flow capacity exist where copper mineralization is disseminated in segmented, very-low-permeability ore blocks. The US Bureau of Mines (USBM) investigated this condition for application to in situ, copper-leach mining at the Cyprus Casa Grande mine site. Moisture retention properties are derived and combined with scanning-electron-microprobe data to characterize the host rock&apos;s mineralogy, texture, pore size, distribution and permeability. Finite element modeling is used to estimate saturated permeability and the ambient degree of saturation and to gain insight into appropriate in situ leach design. Recommended design modifications for optimized solution distribution and maximum recovery from the Casa Grande ore require: • well pressure injection exceeding 1500 psi and recovery wells operating in a suction mode, or • secondary, permeability enhancement by explosive rubblization. In the former, the lack of conditioning and the use of lesser pressures will result in leach solutions confined to the macrofractures. With the latter requirement, pressures can be reduced to 500 psi, with improved recovery and solutions containment.

Jan 1, 1993

The viability of physico-chemical purification methods such as selective flocculation for separation of two components having similar chemical composition and same crystal structure but different surface properties is demonstrated. Loss of selectivity was observed in a dolomite-dolomite mixture with Polyethylene Oxide (5 million molecular weight) as the flocculant. Hetero-flocculation was minimized using a low molecular weight PEO (MW -105) as the site blocking agent (SBA). Near complete separation was achieved at pH 10.5 at 100% recovery level.

Jan 1, 1993

By K. Fuenkajorn, S. Serata

Discussion by S. Serata and K. Fuenkajorn Background Results of the above study in the August 1991 issue of Mining Engineering offer valuable lessons in the solution of cutter-roof problems. The original study plan was initiated by the discussion authors to solve the problems using the "stress control method" of mining (Serata 1976, 1982; Serata, Carr and Martin, 1984; Serata and Gardner, 1986; Serata, Gardner and Preston, 1986; Serata, Gardnerand Shrinivasan, 1986; Serata and Kikuchi, 1986; Serata, Preston and Galagoda, 1987) However, the plan and the planner were changed to the arrangement reported in the paper. The change was considered reasonable at the time due to the mine engineers&apos; uncertainties about the stress control method. Consequently, the basic principle of the study was shifted from the original stress control method to the method described in the paper, which will be called the "yield pillar method" for the purposes of this discussion. The paper convinces the reader that the yield pillar method fails to solve the cutter-roof problems. This doesn&apos;t mean that the stress control method also fails. Actually the contrary is true, as discussed below. Limitation of the yield pillar method The paper illustrates clearly how poorly the yield pillar method performs in solving the problem. The reason for this failure is the lack of the protective stress envelope needed to stabilize the cutter roof. Unfortunately, the protective envelope cannot be formed properly without utilizing the stress control method of mining. Changing the pillar size does not make much difference in the roof stability. Stress measurement The key issue is how to form the global stress envelope to make the gate entries safe for production. Therefore, measuring the stress condition of the ground around the mine opening is critically important to solving the cutter-roof problem, regardless of the method applied. With regard to the stress measurement, there is a serious question as to the reported stress state of [6 i = -51.7 MPa (-7499 psi), G2 = -44.5 MPa (-6458 psi) and 63 = -30.8 MPa (-4465 psi)]. It is mechanically impossible to have such a stress state at any location in the mine ground since the known initial vertical stress [o,,] is less than or equal to 800 psi. There may be a large stress state in the [61] direction, but that is possible only at the expense of the [63] value. Having the above stress tensors in the mine is simply impossible. The questionable, reported stress values could be attributed to the application of the overcoring method, which tends to produce erroneously large stress values in the extremely nonelastic mine ground. Stress control method The paper should be considered as a major contribution demonstrating the limitation of the yield pillar method. At the same time, the paper does not disprove the stress control method. However, in comparing the paper with stress control studies conducted in other similar failing grounds, the stress control method appears to be able to solve the problem more effectively. Therefore it is advisable that the mine not give up its efforts to solve the problem. [•] References Serata, S., 1976, "Stress control technique - An alternative to roof bolting?," Mining Engineering, May. Serata, S., 1982, "Stress control methods: Quantitative approach to stabilizing mine openings in weak ground," Proceedings, 1st International Conference on Stability in Underground Mining, Vancouver, BC, Aug. 16-18. Serata, S., Carr, F., and Martin, E., 1984, "Stress control method applied to stabilization of underground coal mine openings," Proceedings, 25th US Symposium on Rock Mechanics, Northwestern University, June, pp. 583-590. Serata, S., and Gardner, B.H., 1986, "Benefits of the stress control method," invited paper, American Mining Congress Coal Convention, Pittsburgh, PA, May 7. Serata, S., Gardner, B.H., and Shrinivasan, K., 1986, "Integrated instrumentation method of stress state, material property and deformation measurement for stress control method of mining," invited paper, 5th Conference on Ground Control in Mining, West Virginia University, Morgantown, WV, June 11-13. Serata, S., and Kikuchi, S., 1986, "A diametral deformation method for in situ stress and rock property measurement," International Journal of Mining and Geological Engineering, Vol. 4, pp. 15-38. Serata, S., Preston, M., and Galagoda, H.M., 1987, "Integration of finite element analysis and field instrumentation for application of the stress control method in underground coal mining," Proceedings, 28th US Symposium on Rock Mechanics, Tucson, AZ, pp. 265-272.

Jan 1, 1993

By C. A. Young

In-situ Fourier transform infrared/internal reflection spectroscopy (FT ?IR/IRS) has been extended to study oleate adsorption at a calcite surface. The birefringent and transmission limitations of calcite were overcome by using an appropriately designed optical setup and a near-infrared (NIR) spectrometer. An adsorption isotherm was determined at pH 9.2 and room temperature. Comparison with the fluorite/oleate adsorption isotherm determined by the same technique indicates that oleate abstraction by calcite can be as much as one order of magnitude larger than that by fluorite. Nevertheless, the hydrophobicity of the fluorite/oleate surface is greater for equivalent adsorption densities as indicated by contact angle measurements and flotation results. The monolayer region has been confirmed to be chemisorbed oleate at both calcite and fluorite surfaces. Furthermore, multichannel laser Raman spectroscopy (MLRS) showed that chemisorbed oleate at the fluorite surface undergoes a double-bond reaction with oxygen to form an epoxide/polyether complex. Such a reaction, however, could not be detected at the calcite surface. These phenomena are discussed in terms of the intrinsic surface properties of the mineral systems as well as the adsorption density and the cross-linking/polymerization reaction of the adsorbed oleate film.

Jan 1, 1993

By P. Bevilacqua, M. C. Williams, T. P. Meloy

We will bet you that, without prior programming within 10 minutes, we can design and simulate a 10,000 unit operation separation circuit. We will even do it at your place. We do it all the time. [ ] There are no tricks; we do it in a spreadsheet. We do it in those user friendly spreadsheet such as Quattro Pro. Spreadsheets must be user friendly. Accountants use them as do managers, business men, lawyers, doctors and salesmen. What these users seldom realize, is how powerful a mathematical tool a spreadsheet is. Among their other capabilities, spreadsheets can do a finite element analysis. That is why they are useful for accounting. That is also why they are more useful to engineers in the mineral industry. Spreadsheets are ideally suited for the engineering problems in the mineral industry. We have used then for solving problems in: a) mine ventilation; b) circuit design and optimization of dense media, flotation and sizing; c) comminution circuit design; d) shaking tables; e) Humphrey spirals; f) sluice ways and channel flow; g) lock particle and liberation problems; h) tunnel and shaft stress problems; i) cascadograph simulation; j) complex heat transfer problems; k) flow in porous media; and sheet flotation (Figure 1). Mineral industry problems presented on or with a spreadsheet are an excellent teaching instrument, problem statement and solution tools and sales devices. Spreadsheets answer easily, quickly and reliably many mineral industry engineering problems. What makes spreadsheets so useful to the mineral industry. The short answer is: they are easy to use; mineral industry problems fit the spreadsheet format. Those reasons are part of the answer. The real answer lies with the structure of the spreadsheet itself. Essentially, a spreadsheet is a "finite element analysis" form of computer software. Many mineral industry problems are readily solved by finite element analysis techniques. While some in the mineral industry may think they have never heard of finite element analysis, most use it weekly if not daily. Any profit and loss statement is essentially a finite element instrument. In fact, any array of numbers where one number is related to another may be construed as a finite element analysis product. Finite element analysis is a common daily activity. To get an appreciation of a finite element analysis, think of a monthly sales forecast for the next year. For each product and for each month, there exists a dollar figure for the forecasted amount of sales. In the forecast statement, for a given product in a given month, there is a "box" where the forecasted figure is presented. The forecast figure in that box was arrived at through some type of formula. The formula probably required some information from other neighboring boxes in the master forecast statement. Voila, one has a finite element analysis. Today the analysis would be done in a spreadsheet. A typical mineral industry problem is ventilation in an underground mine. Think of a rectangular room and pillar mining operation. Each room has air entering at a given pressure and velocity and air leaving at another pressure and velocity. During steady state, the air entering and leaving the room is determined by conditions in the adjacent rooms. One can readily model the room and pillar mine layout in a spreadsheet, and then find the flow in and out of each room at steady state. Change the flow by moving a brattice cloth or blocking off a path way and one gets a new air flow profile. Change the numbers on the spreadsheet that reflect

Jan 1, 1993

By P. G. Corser

A gold and silver open-pit mine located in northwestern Chile contracted ACZ in 1991-92 to assess the stability of their spent ore pile and to determine the cause and magnitude of cyanide contamination associated with leaching operations. The mine is a conventional open-pit located at an elevation of approximately 4,800 meters (m.) (15,744 feet). A spent ore pile is located approximately 2,000 m. southwest of the mine and approximately 1,000 m. northeast of the active pad and plant facilities. The pile was constructed on a gentle northwest slope dipping 12 to 13 degrees. The pile is bordered by a small river to the northwest and by a larger river to the northeast. Both rivers eventually flow into Bolivia. Heap leaching and processing commenced at the mine in 1988. Since 1988, nearly 6.0 million tons of ore at an average grade of 1.96 grams/ton (0.07 ounces/ton) of gold and 52 grams/ton (1.83 ounces/ton) of silver have been treated by cyanide heap leach methods with zinc (Merrill Crowe) precipitation. In approximately three years of operation, the mine has yielded more than 225,000 ounces of gold and over 1.5 million ounces of silver. Currently ore is agglomerated and hauled to the leach pad by truck and is top loaded to produce a 5-meter lift height. Four contiguous reusable (on/off) leaching pads were constructed with an asphalt layer above a carefully compacted sub-base of High Density Polyethylene (HDPE) liner and screened fines. Leach solution of pH 10-11 containing 1.2 to 1.5 gram/liter of cyanide is applied to the heap at a rate of 10 liter/hour/square meter for a total active application period of 30 days. Leached (spent) ore is transferred to the spent ore pile located approximately 1,000 meters to the northeast. The pile currently contains approximately 6 million tons of spent ore. The pile liner, which has been constructed over a prepared sub-grade consists of three geosynthetic layers (geotextile/flexible membrane liner/geotextile). Long term objectives include washing the pile to recover an additional 3 to 4 percent gold and silver.

Jan 1, 1993

By J. O. Marsden

This paper presents an overview of the innovative methods for gold and silver extraction that have been put into actual practice in North America since 1987. It is an update of a paper of the same title which was presented by Sass and Mansanti at the AMC conference in San Francisco in 1987. New practices, new equipment and variations of older practices that have been introduced in the last five years are discussed in each of the following categories: process selection trends, comminution, gravity concentration, flotation, oxidation, agitated and vat leaching, heap leaching, solution concentration and purification, zinc precipitation, electrowinning, tailings disposal detoxification, and reclamation.

Jan 1, 1993

By Erich U. Petersen

Discussion by Erich U. Petersen Harbuck et al. (1990) present results of research on sulfuric acid leaching of a germanium-gallium ore and shed considerable insight on possible extraction methods for gallium and germanium. However, the presentation does not give sufficient details to evaluate the research, so some of the conclusions may not be as applicable as stated. The objective of this communication is to indicate that relevant and easily obtainable geological and technical information was omitted. Consequently, on this basis, alternative explanations for some of the data are possible. Discussed below are the omission of: • pertinent geological, mineralogical and geochemical literature; • details regarding the determination of germanium concentration in quartz by electron microprobe; and • details on the calculation of the amount of germanium locked in quartz. "These topics are important since the determination of the amount and locus of "unrecoverable, locked germanium" may have an important impact on the economics and methods of germanium extraction and the directions of future research. Harbuck et al. state that "A key to increasing germanium extraction is understanding the mineralogy of the ore." However, only two studies are cited that in some manner describe the mineralogy of the ores. In addition, both of these studies were very preliminary, of limited scope and examined very few

Jan 1, 1993

By M. L. Gupta, S. P. Banerjee, D. C. Panigrahi

The paper describes the computer simulation of climatic conditions in the longwall workings in India. For this simulation work the longwall panels have been divided into two segments, viz; the intake gate segment and face segment. Two computer models, one based upon transient heat and moisture transfer algorithm of McPherson (1986) and the other on quasi-steady algorithm of Starfield and Bleloch (1983), have been developed for intake gate segments. Similarly two computer models, one based upon the transient heat flow in cylindrical tunnel with certain modifications of McPherson algorithm (1986) and the other on linear heat flow concept, have been developed for face segment. The models incorporate the necessary running and spot heat sources present in their respective segments. In addition to this the goaf heat flow parameters have been incorporated in the models for the face segments. Continuous recording of important thermal parameters have been carried out in several longwall faces in India to validate these models and the results have been presented.

Jan 1, 1993

By R. J. Roman

The results of column leaching tests on 3 different mixed oxide/sulfide ores from a Chilean deposit are presented. The 3 samples contained different ratios of oxide copper minerals to chalcocite and chalcopyrite. The results of the column leach tests are interpreted in light of the shrinking core model for coarse particle leaching. The copper recovery from the oxide minerals and the sulfide minerals each conforms to the shrinking core model with the total recovery equal to the weighted average of the individual minerals. The use of column test results to predict field heap leaching results using the multi-mineral shrinking core model is discussed.

Jan 1, 1993