Search Documents

By Donald Leroux, Simon Gariépy, Luc Lachance

"Quantitative information about the quality of metal balance results is often overlooked when making important plant production planning decisions. Not only is this common omission made in a context where many measurements taken in and around mineral processing plants carry significant errors, but it also conflicts with the AMIRA P754 Code of Practice for Metal Accounting. The fact that metal balances are typically published without any indication of data quality may give the wrong impression that the measurements are unquestionably accurate. While it is true that statistical data reconciliation can improve the confidence intervals of redundant variables, there is no data processing technique that brings them down to zero at a finite cost. In this paper, we review the entire data flow, starting from field instruments to metal accounting-based decision-making to show how measurement errors are transmuted into business risks associated with production planning. Necessary conditions for first exposing then quantifying such business risks are stated. Pitfalls to be avoided are also discussed. Finally, a simplified risk assessment and management procedure which considers the quality of metal balance results are applied to a polymetallic mineral processing plant. INTRODUCTION Each and every mineral processing plant has production reporting obligations. In this paper, we are concerned with metal accounting reports (Morrison, 2008) where saleable metal flows and inventories are estimated and published. These metal accounting reports are delivered to a variety of stakeholders who use them for internal management purposes (day-to-day plant production planning, plant operation optimisation, capital spending, etc.) as well as for external management (royalty settlements, tolling agreements, etc.). Hence, there should be no doubt that spotless metal accounting is instrumental to high-quality corporate governance (Gaylard et al., 2014) of mining and metallurgical companies. To this extent, one would have expected industry-endorsed standards to have emerged a long time ago. However, the lack of an accepted set of standard procedures for metallurgical accounting was explicitly recognized as an industry-wide problem only in August 2001 during an SAIMM workshop held in Cape Town, South Africa. Discussions that followed this workshop led to the initiation of the AMIRA Project P754, “Metal Accounting and Reconciliation”, in 2003."

Jan 1, 2015

By A. S. Macfarlane

"SynopsisMetal accounting and reconciliation is an increasingly important governance issue in all mining operations, in that it is required, from a risk management perspective, that the company is in control of its product throughout the whole mining value chain. Reconciliation is a grossly misunderstood term. It means different things to different people, and therefore one of the purposes of this paper is to ensure a holistic and integrated understanding of ‘reconciliation’.Previously, where reconciliation was done, it was often for internal control purposes and loosely applied, sometimes with a low degree of confidence and understanding of the underlying parameters and their natural variability.In most mining operations, issues such as dilution, stope performance, and recovery are critical to profitability and long-term value, and thus understanding and control of these key value drivers is essential, not only from the governance perspective, but also from the perspective of maximizing shareholder returns. In order to implement a system for metal accounting and reconciliation, it is important that the cause and effect of these value drivers is understood, and that a systematic control system be established.While a number of off-the-shelf solutions exist for this work, it is the contention of this paper that a full understanding of the metal flow, its variability, its underlying loss potential, and its control points is necessary before a systematic approach to reconciliation can be undertaken.The paper also advocates that this approach should ensure that the reconciliation system clearly addresses the reconciliation needs, within a consistent framework. Such a framework has been developed by AMIRA, in terms of a metal accounting code. However, up until now, this code has been aimed at plant processes, whereas this paper shows how the concept can be extended to cover the full reconciliation requirements for a base metal mine.IntroductionReconciliation is defined as ‘the process of finding a way to make two different ideas, facts, etc., exist or be true at the same time’. In terms of a mining process, this refers to the comparison of measures and estimates along the value chain, and at different points in time, in order to track and optimize metal recovery. This leads to the notion of having a system in place for accounting for the metal. The University of Cape Town defines metal accounting as ‘… the estimation of (saleable) metal in a mine and subsequent process streams over a defined time period. Comparisons of estimates, from different sources over a specific time period, are called reconciliation.’Traditionally, metal accounting has consisted of geological reconciliations of mineral resource to mineral reserve conversion, mine planning reconciliation related to the reconciliation of long-term plans to short-term plans, grade control reconciliation of head grades to sampled or block grades, and mine survey reconciliation of tonnage discrepancies and mine call factors. In addition, metallurgical reconciliation has tended to be based on metal balancing, followed by some commercial metal accounting that links dispatched product to sales quality, quantities, and revenues. Miners disparagingly refer to this plant process as ‘millmatics’."

Jan 1, 2015

By M. Hermanus, N. Coulson, N. Pillay

"SynopsisThis paper assesses the effectiveness of the Mine Occupational Health and Safety Leading Practice Adoption System (MOSH) and its potential to improve mine health and safety in South African mines. Developed by the Chamber of Mines, which represents the majority of the country's large scale mining employers, MOSH was devised to accelerate progress towards achieving health and safety milestones, which were set by tripartite agreement in 2003. The paper documents and builds on the findings of a study conducted by the Centre for Sustainability in Mining and Industry (CSMI) in 2011 that evaluated MOSH strategy, structures, and process of implementation.The study found that MOSH operated across the mining sector, was directed and dominated by experts and, despite best efforts to include other stakeholders, was led by employers. Statutory worker health and safety representatives and structures were not integrated into the complex change process developed by MOSH. The Mine Health and Safety Inspectorate (MHSI) and organized labour were ambivalent about direct involvement in MOSH and preferred regulatory measures to enforce the participation of mines. MOSH interventions were not targeted at mines with a poor health and safety record, and MOSH lacked a baseline from which to track impacts on sector-wide health and safety performance. The leading practices most widely adopted by mines were designed to improve, rather than fundamentally alter, existing practice. Although the depth of engagement with MOSH among stakeholders and on mine sites varied, mining companies, labour representatives, and the Mine Health and Safety Inspectorate (MHSI) saw the programme as significant.IntroductionIn 2011, the Chamber of Mines commissioned the Centre for Sustainability in Mining and Industry (CSMI) to evaluate the progress and effectiveness of the rollout of the Mine Occupational Health and Safety Leading Practice Adoption System (MOSH). CSMI, based in the School of Mining Engineering at the University of the Witwatersrand, is an independent research centre conducting health and safety research relevant to all major stakeholders in the mining sector. The purpose of the evaluation was to identify the factors that enabled or hampered the adoption of new technologies or practices. The timing of the evaluation, two years before the deadline for the 2013 safety and health milestones, allowed time for adjustments to be made. This paper summarizes the results of the evaluation and includes further analysis and discussion of the nature of the programme and the conditions that act to advance it or it hold back."

Jan 1, 2015

By J. E. Xu, J. Y. Zhang, M. Q. Sheng, K. Wan

"SynopsisThe densities of selected CaO-Al2O3-MgO slag systems were measured at 1823K by the Archimedean method. Thirteen different slag compositions were chosen based on different levels of the MgO content and the mass ratio of CaO/Al2O3. The results indicated that the density of the slag decreases with increasing MgO content (from 0–3.78 mass%), but increases with further increases in MgO content up to 11.33 mass%. At a fixed MgO content of 5.5%, the trend of density change with CaO/Al2O3 in the slag is similar to that for changes in MgO content. On the basis of the regular solution approximation rules of excess molar quantities, an attempt was made to estimate the molar volume of the slags investigated. The application of the molar volume model confirmed that the present expanded approximation rules are applicable to predict the molar volumes of the melts discussed.IntroductionDensity is one of the most important fundamental properties of slags, which influences metallurgicaly phenomena in many ways. Density is sensitive to the nature of the chemical bonds and the species in the melt, and is of great importance not only for theoretical research on the structural properties of molten slags, but also for industrial applications. Density is also required to estimate other key properties used to assess the behaviour of high-temperature molten oxides, e.g. viscosity, surface tension, and thermal conductivity.Liquid calcium aluminate slags that contain magnesia are the basis of most ladle slags for secondary refining processes. The CaO-Al2O3 binary phase diagram (Hallstedt , 1990) shows the eutectic composition (50 wt% CaO and wt% Al2O3) has the lowest melting temperature. The main emphasis of this study is on the 12CaO·7Al2O3 refining slag with MgO additions. The CaO-Al2O3-MgO ternary system is of considerable importance in industrial metallurgical processes, and is fundamental to the understanding of metallurgical slags, ceramic materials, and geological phenomena."

Jan 1, 2015

By Kathryn C. Sole, Owen Tinkler

"Although the first large-scale application of copper recovery by solvent extraction (SX) took place in Zambia in the early 1970s, it is only in the last decade that this technology has become widely employed in this part of the world and is now a mainstay unit operation in most copper hydrometallurgical flowsheets. The mineralogy of the ores in the African Copper Belt, and hence the characteristics of the African leach liquors, differ significantly from those in Chile and the south-western USA, where copper SX has had a long and successful history. These differences provide operators, metallurgists, reagent vendors and engineers with many challenges: new approaches are needed to adapt this technology for successful implementation in this region. This paper examines typical operating practice in the African Copper Belt, discusses differences compared with other parts of the world and looks at some of the challenges and opportunities presented by these flowsheets. INTRODUCTION Following the success of the Rancher’s Bluebird and Bagdad solvent extraction and electrowinning (SX–EW) operations in Arizona in the late 1960s, the Tailings Leach Plant at Chingola, Zambia became the first large-scale copper SX plant in the world, commissioned in 1974. Despite the equipment design now being outdated, this plant still continues to operate successfully, indicating the versatility and adaptability of this technology. Today, there are some 75 copper SX operations worldwide with cathode production above 10 kt/a. The top ten producers currently account for some 40% of the global 4.3 Mt/a SX–EW copper production. South America (predominantly Chile and Peru) is the largest copper cathode-producing region, with annual production of some 2 Mt. The Central African Copper Belt (Zambia and the Democratic Republic of Congo (DRC)) is second, with cathode production of 1.2 Mt/a and North America (USA and Mexico) third, producing close to 0.8 Mt/a Cu (Cytec data, 2014). The remaining 0.35 Mt/a comes from all other regions combined (referred to as “Rest-of-World”). Current and future operations in Zambia and the DRC are summarised in Figure 1. The industry in this region is characterised by a large number of small (3 to 20 kt/a) plants, mainly Chinese-owned, and a few very large (>200 kt/a) operations, owned by major multinational corporations. This paper examines typical operating practice in the African Copper Belt, discusses the differences compared with other parts of the world and looks at some of the challenges presented by the conditions, as well as innovations in flowsheets, reagents and operating conditions that have been introduced in these circuits."

Jan 1, 2015

By von Wielligh. L., D. G. Hattingh, M. N. James, W. Thomas

"SynopsisThe process of joining materials by friction is based on generating the heat necessary to create a solid-state mechanical bond between two faying surfaces to be joined. In simple terms, the components to be joined are subjected to frictional heating between rubbing surfaces, causing an increase in interface temperature and leading to localized softening of interface material, creating what is described as a ’third body’ plasticized layer. This plasticized zone reduces the energy input rate from frictional heating and hence prevents macroscopic melting. The plasticized layer can no longer transmit sufficient stress as it effectively behaves as a lubricant (Boldyrev and Voinov, 1980; Godet, 1984; Singer, 1998; Suery, Blandin, and Dendievel, 1994). The potential for this solid-state frictional joining process to create high-performance joints between, for example, dissimilar materials with limited detrimental metallurgical impact, and reduced defect population and residual stress level, has had a very significant impact on fabrication and repair in industrial sectors such as transport. This paper presents a brief overview of the advances made within the family of friction processing technologies that could potentially be exploited in the nuclear industry as alternative joining and repair techniques to fusion welding.Modern friction processing technologies can be placed into two main categories: those that make use of a consumable tool to achieve the intended repair or joint (friction stud and friction hydro-pillar processing) and those making use of a non-consumable tool (friction stir welding). The most mature friction joining technology is friction rotary welding, where a joint is formed between original parent materials only. A new addition in this category is linear friction welding, which opens the potential for joining complex near-net-shape geometries by friction heating. The continuous innovation in friction processing over the last 25 years has led to the development of a number of unique processes and applications, highlighting the adaptability of friction processes for specialized applications for high-value engineering components.IntroductionAssessing the potential for using alternative joining and repair techniques for specific applications in a given industrial sector is informed by an appreciation of the current size and potential growth in that sector. Power generation by nuclear fission has been out of favour over the past few years, due to several high-profile nuclear incidents, e.g. the Fukushima Daiichi nuclear disaster, as well as concerns over disposal of nuclear waste and spent fuel rods. However, due to rapid increases in the demand for electricity, coupled with many fossil-fuel fired plants reaching end-of-life, there is renewed interest in installing additional nuclear capacity."

Jan 1, 2015

By G. Swan, E. Nordlund, P. Zhang

"SynopsisThe most widely used support design damage criterion for rockburst-prone mines is based upon kinetic energy, which is proportional to the square of the ejection velocity and is commonly expressed in terms of peak particle velocity (PPV). Field monitoring and back-analyses have shown that ejection velocities of the order of 10 m/s and higher can result from seismic events of moderate magnitude. Such velocities are much higher than those predicted using PPV obtained from scaling laws. It has also been found that the peak ground motion (i.e. PPV) on the surface of an excavation is preferentially amplified (by four- to tenfold) compared to the motion in solid rock at a similar distance from the source. However, the wave propagation and interaction processes involved within the fractured rock in generating high ground motion are very complex and are not well understood at this time.In this paper, velocity amplification was investigated by modelling the dynamic interaction between fractured rock and a free surface using a 2D discontinuum-based numerical program, UDEC (Universal Distinct Element Code). A 1D model with a fractured zone was used to represent the fractured rock. Velocity amplification, quantified by PPV, predicted at the free end of the model was 2.0–3.6 times higher than the input velocity. It was found that the wave frequency, fracture stiffness, fracture spacing, and thickness of fractured zone are the main factors that affect the velocity amplification. The results have proved that the interaction of the seismic wave and multiple fractures near the free surface strongly influences the ground motion.IntroductionSince mining-induced seismicity is almost inevitable in deep mines, ground support is generally employed to mitigate the risk of seismically-induced damage. The most widely used support design criterion for seismicallyprone mines is one that seeks to maximize the absorption of the kinetic energy (plus potential energy if a gravity component is considered) of key rock blocks. Based on this criterion, design methods for rock support were first proposed by Wagner (1984) in South Africa and later improved, among others, by Roberts and Brummer (1988) and Kaiser et al. (1996)."

Jan 1, 2015

By T. Celik, B. Genc, C. Musingwini

"This paper discusses a new methodology for defining and measuring mine planning software utilization in the South African gold mining sector within an evolving data-set framework. An initial data-set showing the mine planning software providers, their corresponding software solutions, as well as the software capabilities and information on the number of licences was collected and compiled in 2012 in an online database for software utilized in the South African mining industry. Details of the database development and implementation were published in the Journal of the Southern African Institute of Mining and Metallurgyin 2013. In 2014 the data-set was updated with additional and new information. Using the 2012 and 2014 timestamps, a methodology for estimating the software utilization was developed. In this methodology, the three variables of commodity, functionality, and time factor were used to define and measure the software utilization in order to ultimately inform decision-making strategies for optimal software utilization. Using six different functionalities, namely Geological Data Management, Geological Modelling and Resource Estimation, Design and Layout, Scheduling, Financial Valuation, and Optimization, utilization in the gold sector was measured. This paper presents the methodology employed for measuring the mine planning software utilization. The methodology is useful for stakeholders reviewing existing software combinations or intending to purchase new software in the near future and who want to estimate the comparative attractiveness of a certain software package. These stakeholders include mining companies, consulting companies, educational institutions, and software providers. The work presented in this paper is part of a PhD research study in the School of Mining Engineering at the University of the Witwatersrand."

Jan 1, 2015

By P. Venter, N. Naude

"Coal mining is a thriving industry and 53% of the coal mined in South Africa is used for electricity generation. Mechanization has made coal mining more efficient, but fines generation has subsequently increased. Up to 6% of the run of mine material can report to the -200 µm fraction. Common problems associated with fines handling include dust formation, storage problems, and high moisture levels. A method to turn this material into a saleable product instead of stockpiling it can add value to a company.Briquetting is a pressure agglomeration method where loose material is compacted into a dense mass (FEECO International, 2014). The briquettes must be able to withstand rigorous handling and transport operations without disintegrating. This study aims to investigate the optimum binder and moisture conditions required to produce a mechanically strong briquette using two different binders - a PVA powder (binder A) and a starch powder (binder B).It was found that for binder A the optimum moisture level was 12% to 14%. At this moisture level the greatest compression strength gains were observed, and low amounts of fines produced in impact and abrasion tests. The minimum amount of binder added while still obtaining a strong briquette was 0.5% binder A. For binder B the optimum moisture level was also 12% and the minimum amount of Binder B to be added was found to be 1%. Briquettes that were dried outside reached their peak strength after about four days, whereas the briquettes that dried inside took about 20 days to reach their strength plateau. Hardly any degradation took place on the surface of the binder A film after exposure of 300 hours of artificial weathering. Thermogravimetric analysis confirmed that neither binder A nor binder B will add to the ash content of the coal fines, as both binders totally decompose above 530°C.Binder B yielded stronger briquettes after 15 days and also generated less fines. It is therefore superior to binder A and would be recommended for further use.Paper written on final year project work carried out in partial fulfilment of B.Eng degree in Coal Beneficiation"

Jan 1, 2015

By H. F. Niemand, C. J. Postma, P. L. Crouse

"SynopsisThe separation of zirconium and hafnium is essential in the nuclear industry, since zirconium alloys for this application require hafnium concentrations of less than 100 ppm. The separation is, however, very difficult due to the numerous similarities in the chemical and physical properties of these two elements.Traditional methods for separation of zirconium and hafnium rely predominantly on wet chemical techniques, e.g. solvent extraction. In contrast to the traditional aqueous chloride systems, the AMI zirconium metal process developed by Necsa focuses on dry fluoride-based processes. Dry processes have the advantage of producing much less hazardous chemical waste.In the proposed AMI process, separation is effected by selective sublimation of the two tetrafluorides in an inert atmosphere under controlled conditions, and subsequent selective desublimation. Estimates are made for the sublimation rates of the two tetrafluorides based on the equilibrium vapour pressures. A sublimation model, based on the sublimation rates, was developed to determine if the concept of separation by sublimation and subsequent desublimation is theoretically possible.IntroductionZirconium requires several purification steps to conform to nuclear-grade specifications. Little information is available on the sublimation separation of Zr and Hf compounds, especially in the fluoride form, the majority of which deals with sublimation under vacuum conditions. On the industrial scale, only vacuum sublimation of ZrF4 has been reported. No records were found for the sublimation of ZrF4 in an inert atmosphere. Information on the sublimation rate of ZrF4 or HfF4 in an inert atmosphere is also limited. The rate is assumed to be dependent on several factors, of which temperature, area, and composition are considered the most important."

Jan 1, 2015

By H. M. Stewart, N. F. Dawson, J. P. Beukes, P. G. van Zyl, Q. P. Campbell, A. Jordaan, R. I. Glastonbury, L. N. Sadiki

"SynopsisThe physical properties of oxidative sintered pellets produced from typical South African UG2 ore are compared with the physical properties of pellets produced with conventional South African metallurgical-grade chromite ore (from the Lower Group 6 or the Middle Group 1 and 2 seams). A statistical evaluation of the cured (sintered) compressive strengths proved that pellets prepared from UG2 ore are likely to have the same, or better, compressive strength than pellets prepared from metallurgical-grade chromite ore. The cured abrasion strength of the UG2 pellets was also superior to that of the metallurgical-grade pellets. Scanning electron microscopy (SEM) backscatter, secondary electron, and elemental X-ray mapping were used to determine the reasons for the general superior strength of the UG2 pellets. The case study UG2 ore also required 13 kWh/t less energy for milling to attain the required particle size distribution prior to pelletization, which can lead to substantial cost savings. Results presented in this paper can be utilized by ferrochromium (FeCr) producers to better quantify the advantages and disadvantages associated with the use of UG2 ore for FeCr production.IntroductionChromite, a mineral of the spinel group, is the only commercially viable source of virgin chromium units. Geologically, commercial chromite deposits in the world are found in three forms, i.e. alluvial-, podiform-, and stratiform-type deposits (Murthy et al., 2011; Cramer et al., 2004). Alluvial deposits were formed by weathering of chromite-bearing rock with the subsequent release of chromite and gravity concentration by flowing water. However, these deposits are relatively small and of comparatively minor commercial interest. Podiform-type chromite deposits usually occur as irregularly shaped pods or lenses, and their distribution within a mineralized zone is usually relatively erratic and unpredictable, making the exploration of these deposits difficult and costly (Cramer et al., 2004). Stratiform-type chromite deposits occur as parallel seams in large, layered igneous rock complexes with more regular layering and lateral continuity (Cramer et al., 2004). The largest example of a stratiformtype chromite deposit is the Bushveld Complex (BC) in South Africa, which holds an estimated three-quarters of the world’s viable chromite ore resources (Cramer et al., 2004).Several chromite seams exist in the BC. The seams of economic interest are the Lower Group 6 (LG6), the Middle Group 1 and 2 (MG1 and 2), and the Upper Group 2 (UG2) seams (Cramer et al., 2004). The LG and MG seams are specifically exploited for their chromium content, while the UG2 seam is mined primarily as a source of platinum group minerals (PGMs) (Xiao and Laplante 2004). Extraction of the PGMs from the UG2 ore usually involves the liberation of the sulphide by milling and subsequent recovery of the PGM concentrate through flotation (Xiao and Laplante, 2004). Chromite in the PGM concentrate is undesirable; therefore, PGM recovery circuits are specifically designed to ensure maximum rejection of the chromite to the tailings stream. However, the chromite in the PGM tailings can potentially serve as feedstock for ferrochrome (FeCr) production, after beneficiation to increase the chromium content."

Jan 1, 2015

By M. Yavuz

One of the challenging problems for optimization in mining operations is to choose the best equipment among the alternatives. Equipment selection is an important task for mine management due to its operational cost, and is also an integral part of mine planning and design. Equipment selection is not a well-defined process because it involves the interaction of several subjective factors or criteria. Besides, decisions are often complicated and may even embody contradictions. Therefore, equipment selection is considered as a multi-criteria decision-making process, and suitable decision-making methods should be employed in this process. In this study, the loader selection for Aegean Lignite Colliery was made by using both the analytic hierarchy process and Yager’s method. Owing to the misusage of Yager’s method in the past, a new procedure is proposed in this paper for making proper decisions. It is highly recommended in this purposed method that criteria or alternatives should be grouped so as not to exceed the limitations of human performance (nine criteria/alternatives). The most appropriate solution for the loader selection was investigated by obeying this limitation for each method, and the results were compared. At the end of the decision-making process, a sensitivity analysis was applied for each method in order to see how a criterion affects the final decision. The advantages and disadvantages encountered during the application of each decision-making method are presented.

Jan 1, 2015

By S. Mohanta, B. C. Melkap

"SynopsisDry beneficiation of coal by air dense medium fluidized bed is an emerging trend. It is widely believed that the particle size of the medium has a significant effect on the separation efficiency. This investigation demonstrates that medium particle size has a major effect on separation efficiency. Experimental results show that different size fractions of the same feed respond differently to the same size fraction of medium solids. Furthermore, a particular size fraction of feed coal responds differently with different size fractions of medium solids. The Ep values and overall metallurgical performance parameters, obtained from experimental results, clearly indicate the superior performance of an air dense medium fluidized bed separator when using –150+106 µm magnetite powder as the fluidizing medium. These observations reinforce the importance of sizing the medium particle size for the air dense medium fluidized bed.IntroductionIn an air dense medium fluidized bed (ADMFB), a fluidizing bed of a particular density is created by suspending solid particles in an upward air flow. A feed containing coal particles of different densities is introduced into this fluidizing bed. The particles with relative density less than the bed density float on the top of the bed, while particles denser than the bed density sink through it. Since there is a general correlation between ash content and density of coal particles, it is possible to remove ash-forming impurities from a raw coal to the required level by regulating the density of the fluidizing bed. Recently, the ADMFB process has received significant attention world-wide for its specific advantages of low operating cost and less restrictive for small capacities (Luo and Chen, 2001; Houwelingen and de Jong, 2004; Dwari and Hanumantha Rao, 2007; Sahu et al., 2009; Mohanta et al., 2012). This process is not recognized as a well-established industrial practice because of the availability of efficient wet processing technology. However, with the revival of interest in dry beneficiation of coal in general, and ADMFB in particular, there is a concerted effort to improve the efficiency of the ADMFB process, and successive improvements have made the process a competitive and viable option for beneficiating coal."

Jan 1, 2015

By E. Pardo-Igúzquiza, R. A. Olea

The bootstrap is a computer-intensive resampling method for estimating the uncertainty of complex statistical models. We expand on an application of the bootstrap for inferring semivariogram parameters and their uncertainty. The model fitted to the median of the bootstrap distribution of the experimental semivariogram is proposed as an estimator of the semivariogram. The proposed application is not restricted to normal data and the estimator is resistant to outliers. Improvements are more significant for data-sets with less than 100 observations, which are those for which semivariogram model inference is the most difficult. The application is illustrated by using it to characterize a synthetic random field for which the true semivariogram type and parameters are known.

Jan 1, 2015

By J. W. van der Merwe, A. Palazzo

"Owing to the corrosiveness of the untreated brackish cooling water typically used for steel mills (and other environments), it is important to treat the water and monitor corrosion in such systems. Generally, corrosion rates are monitored with corrosion probes inserted into a pipeline or vessel. This has been standard practice for many years, and is widely accepted in industry. Typically, two kinds of probes are used - electrical resistance and linear polarization resistance (LPR) probes.In this study, the effectiveness and accuracy of the LPR technique was evaluated by comparing the electrochemical measurements with the results of mass loss tests using corrosion coupons. The corrosivity of the environment, a synthetic brackish water, was varied by varying the calcium hardness and alkalinity, and to simulate actual plant conditions temperatures of 35°C and 45°C were used. In addition to the corrosion rate measurements, the iron concentration was measured, as well as the imbalance from the probe.The corrosion rates obtained by LPR were from 57% lower to 385%higher than those from the immersion tests. Most probe measurements were higher than the immersion results, and 50% of the probe results were50% or more higher than the immersion results. The best correspondence between the two methods was obtained at low calcium levels, except for one measurement that was 93% higher than the coupon results. There was no clear correlation between parameters such as temperature and total alkalinity and the difference between the results. It would therefore appear that LPR measurements can differ significantly from immersion results, and LPR results should therefore be used with caution in industrial applications."

Jan 1, 2015

By M. Q. W. Jones

This paper presents a compilation of physical properties of rocks from the Bushveld Complex. The database consists of more than 900 measurements each of thermal conductivity and density. The data are well distributed from localities around the Complex and most rock types are well represented. Thermal conductivity and density are shown to vary widely in the ranges 1.8-4.2 W m-1K-1and 2600-4200 kg m-3respectively. Although only 190 heat capacity measurements are available, this parameter is quite uniform for most rock types present, 800-900 J kg-1K-1, except for chromitite, which has a lower average, 750 J kg-1K-1. Rocks encountered in deep platinum mines are particularly well characterized and this has important implications for prediction of mine refrigeration requirements. The heat flux into a semi-infinite region with properties typical of the Bushveld Complex as a function of time is substantially lower than an equivalent model for the Witwatersrand Basin.

Jan 1, 2015

By L. K. Witika, J. H. Masinja

"Investigations of flotation characteristics of Lumwana and Kansanshi ores using formulated frothers were carried out. Of the six frothers tested, two came from the alcohol family, two from the glycol family and last two were formulated products. The initial work involved determining the optimum mesh of grind and frother dosage for Lumwana and Kansanshi ores. Further work involved carrying out surface tension, bubble size and froth stability measurements. Finally, water recovery tests were conducted at Lumwana and Kansanshi mine sites. For froth stability tests, six frothers were tested on a two-phase (water–air) system using the Bikerman column flotation cell, while water recovery tests were conducted using a total of seven frothers, including the standards for each plant. The results of the testwork showed that (i) although a stable froth is essential for optimum recovery of valuable minerals, a higher molecular weight frother, like Dowfroth 250, caused poor selectivity when used on fine ores and (ii) a lower molecular weight frother was suited for Lumwana ore, while a mid to higher molecular weight formulated product was suitable for Kansanshi sulphide ore. INTRODUCTION Investigations of flotation characteristics of Lumwana and Kansanshi ores using formulated frothers were carried out. The initial work of this project involved determining the optimum mesh of grind and frother dosage for Lumwana and Kansanshi ores. Further work involved carrying out surface tension, bubble size and froth stability measurements. Finally, water recovery tests were conducted at Lumwana and Kansanshi mine sites. In order to investigate the gangue entrainment levels in the Lumwana and Kansanshi sulphide ores, two well-known methods (froth stability and water recovery) were used. Firstly, froth stability tests were conducted using six frothers, two from the glycol family (Dowfroth 200 and Dowfroth 250), two from alcohol family (MIBC and pine oil) and other two from the formulated family (Betafroth 20 and Betafroth 245), at the University of Cape Town’s Centre for Mineral Research (CMR) laboratories. Froth formation and stability measurements were conducted using the Bikerman column flotation cell."

Jan 1, 2015

By D. Toporov, R. Abraham

"Gasification is a process of thermal conversion of solid carbonaceous materials into a gaseous fuel called syngas. Coal gasification is an efficient technology for a range of systems for producing low-emission electricity and other high-value products such as chemicals, synthetic fuels, etc.The paper presents the High-Temperature Winkler (HTW) gasification process, which is designed to utilize low-rank feedstock such as coals with high ash content, lignite, biomass etc. The process is characterized by a bubbling fluidized bed, where coal devolatilization and partial oxidation and gasification of coal char and volatiles take place, and by a freeboard where partial combustion and gasification of coal char take place.The recent development of the high-pressure HTW process is reviewed. Gasification of low-rank, high-ash coals with respect to gasification temperatures, conversion rates, and syngas quality is also discussed. The main HTW design steps required for an industrial-scale design are presented. Special attention is given to the process modelling, including global thermodynamic calculation as well as detailed CFD-based simulation of a reacting fluidized bed. Three-dimensional numerical results of the HTW process are also provided and discussed."

Jan 1, 2015

By M. M. Bwalya, F. K. Mulenga

"SynopsisThe application of the attainable region (AR) technique to the analysis of ball milling is currently limited to batch data. This paper introduces the use of the technique to continuous milling.To this end, an industrial open milling circuit processing a platinum ore was surveyed. Samples were collected and later characterized by means of laboratory batch testing. On site, several milling parameters were varied systematically so as to collect data for modelling purposes. These paramters included ball filling, slurry concentration, and feed flow rate. After data analysis, a simulation model of the open milling circuit was developed under MODSIM®, a modular simulator for mineral processing operations. The mill was then simulated and the data generated was analysed within the AR framework.Initial findings reveal an opportunity to gain valuable insight by studying milling using the AR technique. From an exploratory perspective and inasmuch as this study is concerned, feed flow rate, ball size, and ball filling were identified as being pivotal for the optimization of open ballmilling circuits. Mill speed, on the other hand, had only a limited effect on the production of particles in the size range -75 +10 µm.IntroductionGlasser and Hildebrandt (1997) propounded the attainable region (AR) as a technique for the analysis of chemical engineering reactor systems. Results have since been produced and tested on both the laboratory and pilot scales. The method results in a graphical description of chemical reactions by considering the fundamental processes taking place in the system, rather than the equipment. From the plotted graphs, the process and the reactors can be synthesized optimally into a flow sheet.The use of the AR method still has a long way to go as far as mineral processing is concerned. For instance, several articles have reported the application of the AR technique to ball milling: Khumalo et al. (2006, 2007, 2008); Khumalo (2007); Metzger et al. (2009, 2012); Metzger (2011); Katubilwa et al. (2011); Hlabangana et al. (2012). Their main shortcoming has been the exclusive use of laboratory batch grinding data.To address this deficiency, Mulenga and Chimwani (2013) proposed a way by which the technique could be extended to continuous milling. In effect, the batch milling characteristics of a platinum-bearing ore (Chimwani et al., 2013) were used and scaled up to an open milling circuit. Then, with simplifying assumptions, an attempt was made to optimize the residence time of particles inside the mill. Later, Chimwani et al. (2014a) presented some optimization examples involving various milling parameters. The sequence of published articles then paved the way for the study of industrial milling systems with the AR methodology."

Jan 1, 2015

By S. Ndlovu, M. Malatse

"The Witwatersrand Basin is the heart of South Africa’a gold mining industry. The cluster of gold mines located in the Witwatersrand Basin generates a significant amount of mine tailings, which have adverse effects on the environment and ecological systems. In addition, disposal costs are very high. The exponential population growth in the Witwatersrand area has resulted in pressure on the reserves of traditional building materials. Quarrying for natural construction material is very expensive and damages the landscape. This work therefore examines the use of gold mine tailings in the production of bricks.Different mixing ratios of gold tailings, cement, and water were used. The resulting bricks were then cured in three different environments - sun dried, oven dried at 360°C, and cured in water for 24 hours. The bricks were then tested for unconfined compressive strength, water absorption, and weight loss. The results showed that the mixture with more cement than tailings had a compressive strength of approximately 530 kN/m2. It was also found that the best brick curing system was in a water environment. Bricks made from tailings cost more than conventional bricks because of the higher quantity of cement used, but the manufacturing process consumes less water. Overall, the results indicated that gold mine tailings have a high potential to substitute for the natural materials currently used in brickmaking.Paper written on project work carried out in partial fulfilment of BSc. Eng. (Metallurgyand Materials Sciences)"

Jan 1, 2015