Search Documents

Iron ore pellets with or without additives are commonly used as alternate charge material in both conventional and newer ironmaking processes. The performance characteristics of these pellets are normally assessed on the basis of their reducibility values, reduction strength and resistance to clustering. These properties depend mainly on the type and amount of additives and on the sintering phenomena of the pellets during firing. In the case of composite pellets (ore-coal pellets), reduction and sintering of the iron ore fines occur simultaneously. The thermodynamic and reaction mechanisms of the processes involved in the reduction of iron ore pellets with and without reductants, additives, etc., may not necessarily be identical. The reduction and sintering characteristics of pellets greatly influence the reaction mechanism and the surface morphology of the reduced pellets. The approaches in the literature to the analysis of these reduction and sintering phenomena are broadly categorized as follows: (i) empirical models, (ii) models based on kinetics, and (ill) models based on morphological changes. The relative merits and de-merits of these models are illustrated by their application to the reduction of fluxed ore-coal composite pellets. A critical analysis of the investigations that have been conducted on the reduction and sintering behaviour of such pellets is given. It is shown that, although elegant empirical models and kinetic equations have theoretical significance and can be usefully employed in elucidating the reaction mechanisms of iron ore lumps, they are sometimes not directly applicable to fluxed ore-coal composite pellets. In studies of the latter, the approach should be to correlate the morphological changes with the reduction mechanism. The paper also gives a brief account of an investigation on the reduction and sintering aspects of fluxed composite reduced iron pellets.

Jan 1, 1996

South Africa?s now a member of this body, tailored on the World Bank, and headquartered in Abidjan-Cote d'Ivoire. As a funding agency for capital projects within 59 member countries of the ADB it is to be expected that there are guidelines to the requirements for funding application and for project management and control.

Jan 1, 1996

By I. Bock

This presentation describes a technique under development referred to as Selective Blast Mining. The technique involves millisecond sequential blasting. It applies to mines where the gold bearing conglomerate band is clearly demarcated, and separated from the waste rock in the foot and hanging wall. The width of the conglomerate band should be less than ± 0,7 metres. A research program was initiated in August 1994 by Drs RE. Robinson and I.E. Bock. The objectives were to develop new blasting methods that can reduce: ? the losses of gold in narrow reef stoping. Losses of gold can be as much as 10-15% ? and to introduce selective mining to reduce ore dilution with waste rock.

Jan 1, 1996

By M. Coetzee

The susceptibility of experimental low-nickel Cr-Mn-N stainless steels to hot cracking, sensitization, and pitting corrosion in the as-welded condition was investigated. These steels were developed for deep-drawing applications and are similar in composition to type 201 stainless steel. In order to obtain good formability, the rapid rate of work-hardening (characteristic of the 200-series steels) was decreased by the addition of copper. The behaviour of two sets of alloys during fusion welding was investigated: 17Cr-7Mn-4Ni-o.5Cu steels containing 0.001 to 0.27 per cent nitrogen, and 17Cr-7Mn-2Ni-o.1N steels with copper contents varying between 0.01 and 3.11 per cent. Al the steels in these two sets initially solidify as d-ferrite, which transforms partially to austenite during cooling. As the nitrogen level increases, the microstructure of an autogenous-weld metal ranges from large amounts of d -ferrite, martensite, and Widmanstätten austenite, to austenitic structures with small amounts of vermicular d -ferrite. The formation of d -ferrite during solidification and the presence of ferrite retained in the weld metal indicate that the experimental alloys will not be susceptible to hot cracking during welding. Except for the alloy with 0.27 per cent nitrogen, the resistance to pitting corrosion of the experimental steels in the as-welded condition is inferior to that of type 304 stainless steel. None of the experimental steels is susceptible to intergranular attack in the as welded condition. The alloys with 0.19 and 0.27 per cent nitrogen have properties (corrosion and microstructure) similar to those of type 304 stainless steel in the as-welded condition.

Jan 1, 1996

Council for 1995/96 President D.A. J. Ross-Watt President Elect Dr N.A. Barcza Vice Presidents Senior R.P. Mohring Immediate Past President J.A. Cruise Junior J.R. Dixon Honorary Treasurer J.A. Cruise

Jan 1, 1996

By H. White

The applicability of ground penetrating radar (GPR) in numerous qualitative applications has been demonstrated over the past five years in the South African mining industry. These applications include the delineation of faults and dykes, fracture mapping, delineation of shear zones, mapping of depth of weathering, and the delineation of contact between different rock types. The qualitative nature of the data collected using existing commercial GPR systems, often relying on expert interpretation, has however mitigated against the full scale routine application of GPR in the mining industry. The recent development of the RockRadar system by ISS International has, to a large extent, overcome these problems. The result is that quantitative rock-mass studies can now be performed with the RockRadar system.

Jan 1, 1996

By D. R. Hardman

South Africa is the third-largest supplier of coal on the world's export markets after Australia and the USA, and the second-largest supplier of bituminous steam coal following Australia. There are many Similarities between the coal industries of South Africa and those of Australia and the USA, in contrast to the coal industries in Europe. For South Africa to maintain a competitive position on the export markets, it must continue to compete against these two countries. It is therefore important that the performance of the loca1 coal industry should against that of the Australian and US coal industries. Although financial performance is the major criterion, financial information is not easily obtained, and the paper therefore uses employee productivity in the form of tonnes per man year as a means of comparison. The paper reviews recent trends in the level of production and numbers of employees prior to review1ng the productivity. The influence on productivity of some mining methods is highlighted. It is realized that published information (information available within the public domain) can contain anomalies, but every effort is made to compare data of a similar type. Notwithstanding possible inaccuracies, it is shown that South African coal-De productivity lags far behind that of Australia and the USA. The significance of the difference is that the South African coal industry is able to apply overseas practices and procedures that have been shown to give improved performance, and that the increased use of more productive extraction techniques has limited application.

Jan 1, 1996

Despite the media's use of the mining industry as a whipping boy over its perceived attitude towards the environment, the facts remain that the only legislated requirement in the SA Statute Books for any form of environmental impact-assessment prior to development is to be found in the Minerals Act in the form of an EMPR. Not only is our industry complying with this requirement, but moves are afoot to set up environmental management systems for existing operations in preparation for seeking accreditation under ISO 14001 when published towards the end of this year. On how broad a front are we advancing? ? Is the industry equipped to handle these challenges? ? Does it have the determination to overcome its problems? ? Do we realise that failure may mean the loss of markets overseas to competitors who can meet the international standards? ? Where are the shortcomings and when must our efforts be focussed?

Jan 1, 1996

By Jean-Claude Paye

In February 1996 the OECD's Environment Policy Committee will commemorate its 25th anniversary with a fifth meeting at Ministerial level. Environment ministers will be taking stock of the progress made by OECD countries in protecting and managing the environment in that quarter-century, and sharing views on likely challenges and co-operative responses. Ministers can point to many important accomplishments. Scientific understanding and technological tools for establishing and monitoring risks to human health and the environment have improved dramatically since the early 1970s. All OECD countries now have in place comprehensive environmental legislation, supported by specialized institutions for policy design, implementation and enforcement. The results of these efforts are increasingly evident in the form of cleaner air and water, and improved protection of natural areas, notwithstanding the many complex problems that remain.

Jan 1, 1996

To the members of The South African Institute of Mining and Metallurgy We have audited the annual financial statements set out on pages 272 to 277. These financial statements are the responsibility of the Institute's Council. Our responsibility is to report on these financial statements. We have conducted our audit in accordance with generally accepted auditing standards. These standards require that we plan and perform the audit to obtain reasonable assurance that, in all material respects, fair presentation is achieved in the financial statements. The audit included an evaluation of the appropriateness of the accounting policies, an examination, on a test basis, of evidence that supports the amounts and disclosures included in the financial statements, an assessment of the reasonableness of significant estimates, and a consideration of the appropri¬ateness of the overall financial statement presentation. We consider that our auditing procedures were appropriate in the circumstances to enable us to express our opinion presented here. In our opinion these financial statements fairly present the financial position of the Institute at 30th June, 1996, and the results of its operations for the year then ended in conformity with generally accepted accounting practice.

Jan 1, 1996

By M. H. Moys

I had the good fortune to attend the above Conference which was held in Kanpur, India, on 11-15 December, 1995. The Conference was held in honour of Professor P.C. Kapur of the Indian Institute of Technology in Kanpur. Professor Kapur was one of the early students of legendary teacher and researcher of mineral beneficiation, Professor Doug Fuerstenau of the Department of Materials Science and Engineering at the University of California at Berkeley. I have attended my fair share of international conferences and this one certainly rated at the top of the list on several counts. With an open-hearted hospitality which one might almost take for granted once you have spent some time in India, the organizers of the Conference looked after every need of their guests, including breakfast and transport to and from the conference centre, wonderful traditional lunches and dinners and outstanding entertainment in the evenings. The papers were generally of a high standard, and debate flowed enthusiastically and freely. Several international guests delivered seminal papers in their fields as discussed below.

Jan 1, 1996

By M. B. Cortie

The historical development of materials engineering in the mining industry Is briefly reviewed, and some of the factors currently influencing the industry in South Africa are discussed. Material usages in various parts of the mining operation are surveyed. The predominant mechanisms in the degradation of materials in mines are wear, corrosion, and fatigue. The issue of corrosion-abrasion Is considered, but it Is concluded that abrasive wear predominates in most rock-handling and comminution applications and that, in general, little economic benefit Is to be gained in those applications by the use of existing corrosion-resistant alloys. However, alloys with a measure of corrosion resistance find profitable application elsewhere in the mining environment. The use of other engineering materials such as polymers, ceramics, al1l1inium, and various ferrous alloys may be economically viable in a variety of niche situations. Identification of the most cost-effective material in each case calls for a systematic approach and some patience.

Jan 1, 1996

The possibility that type 430 stainless steel can become sensitized during annealing after hot-rolling was studied by simulated cycles of continuous-annealing heat treatments, and by calculation of the carbon solubility. It was found that the lower-carbon steel could be sensitized at lower annealing temperatures than the higher-carbon steel, which is in line with plant experience. The difference in sensitization behaviour is ascribed to the lower rate of recovery of the lower-carbon steel during cooling, since recovery is sensitive to the grain size. At practical heat-treatment temperatures, austenite formation does not play a role.

Jan 1, 1996

The 99th Annual General Meeting of The South African Institute of Mining and Metallurgy was held in the Gold Room, Transvaal Automobile Club, 60 5th Street, Lower Houghton, Johannesburg on Wednesday, 14th August, 1996. Obituaries The President announced the death, during the year, of the following members: Life Fellows H.L. Munro, H.S. Simpson, P.L. Ward Fellows I.M. Hossy, A.E. O'Meara Retired Fellows E.A. Arvidson, R.F. Bourne, F. Hawke, W. Lloyd, J.M. Meyer Members J. Allen, P.A. Boardman, L.M. Jacobs, G.F. Marx, G.D. Perry, R.W. Spraggs Retired Member M. Milner Associate I. Pieterse. In memory of the deceased and in sympathy with the bereaved, all rose and observed a moment of silence.

Jan 1, 1996

By N. A. Barcza

Pointing out that South Africa needs to utilize its wealth-creating activities, together with local and international investment, to further develop its industries, the address asserts that the mining and minerals industries, especially in the manufacture of beneficiated products, offer the greatest potential for South Africa to achieve its goal. As many mineral-beneficiation processes are based on pyrometallurgical routes, the address goes on to describe some historical - pyrometallurgical operations and to indicate probable developments in the future. These include growth in the fields of both precious and base metals. After discussing environmental and recycling matters, together with manpower requirements, the address concludes that the major growth in the mining and minerals industries will occur in the manufacture of steel, stainless steel, ferro-alloys (particularly ferrochromium), aluminium, and titania slag.

Jan 1, 1996

Today's conservation thinking is becoming increasingly polarised-a widening gap that could eventually be to the overall detriment of mankind, one way or the other. In one corner, stand the disciples of the untainted wilderness, moral protectors of the natural world who subscribe to the doctrine that the fragile balance of nature is threatened by man's very existence. On the opposite side of the ring, stands the relentless developer, with the megalomaniac notion that nature is purely there to serve humanity and civilisation, under the auspices of 'progress',

Jan 1, 1996

Contribution by W. Assibey-Bonsu I congratulate Mr N.O. Lotter on his paper. There are two main aspects of the paper on which I would like to comment. One aspect is his review of P. Gy's sampling theory under the heading 'Sampling the mill feed' (p. 153). The other aspect relates to his reference to one of our papers1 that was published in the Journal (p. 152). My comments on the former will be given elsewhere'. Authors' reply: Dr Assibey-Bonsu's contribution to the subject is appreciated.

Jan 1, 1996

By C. R. Speers

The induced elastic stresses in the sidewalls of gold-mining tunnels at a depth of 4000 m in the Witwatersrand exceed the peak compressive strength of even the best-quality quartzite rocks. Laboratory tests measuring post-yield stress versus strain response show that brittle fracture occurs, followed by a loss in strength associated with strain-softening behaviour. Numerical modeling based on an assumed Mohr-Coulomb criterion fitted to the test results shows that large ongoing deformations of the sidewall occur, leading to total tunnel failure without adequate support. A methodology is presented to enable a quick assessment to be made of support requirements in terms of ground characteristic curves for numerically derived pressure versus displacement. From these curves, estimates can be made of the force levels for cable bolting and of the thickness and strength requirements for shotcrete linings. As an example of its application, the methodology is used in a comparison of the relative stability efficiencies of a square-shaped tunnel and a horizontal ellipse-shaped tunnel.

Jan 1, 1996

The Proceedings of the above Symposium have been edited and published by the Symposium Committee. The Symposium was sponsored by the Australian Coal Association, the Joint Coal Board, and the United Nations Economic Commission for Europe. The Symposium was very well attended, with presentations from fourteen countries, including all the major coal-producing countries of the world. The Proceedings are presented in two parts: the Symposium Part and the Workshop Part. The Symposium Part deals basically with the theoretical aspects of outbursts and high-gas emissions in mines, while the Workshop Part is more practically oriented and describes case studies, and the management systems, and drilling technologies used in underground mines.

Jan 1, 1996

By J. Markgraaff

Because composites offer new solutions to materials problems, they are currently the focus of intense research and development worldwide. However, the natural tendency of users is to remain with tried materials in every situation of material selection. This approach ignores the tremendous advances that have been made in composite materials and their application. These advances enable engineers to tailor composites to suit specific applications such as the demanding needs of mining and industry in South Africa. However, the application of composites, where new and improved components and products are needed or are being developed is often hampered by the limited knowledge and experience of the engineers concerned. This paper presents some of the basic information needed for an appreciation of the terminology, definitions, and properties of various types of composites. It also reviews recent developments in manufacturing technology and product development that may find application in local industries and mining.

Jan 1, 1996