Search Documents

By Chi-Mun Song, Seok-Hyun Choi, Seok-In Hong, Han-Kee Jang

Accurate measurement and evaluation of hand-transmitted vibration from a power tool is an important issue for tool manufacturers, because they are obliged to develop low-hazard power tools for workers. The International Standard ISO 5349(1) dictates a systematic procedure for the measurement and evaluation of hand-transmitted vibration. However, the uncertainty in this measurement is too large for manufacturers to apply such data to the design and modification of power tools. There can be several sources of this uncertainty in such measurements; e.g., operator-dependent, power tool-dependent, and operational conditions (see Table 1). For a manufacturer to characterize the exposure of a power tool’s use to a given level of vibration, the relationship between these uncertainty factors and the measured vibration must be elucidated. In this study, we investigated the effect of several factors on the uncertainty in measurements. [ ] Methods In this study, some of the factors in Table 1 were selected for examination, and their effect on the measured variation was quantitatively investigated. Three tools from the same manufacturer were sampled at random in our experiments, and each of five of the same type of insert (disks or tips) was installed into each tool. Although each of the tools and inserts were of the same design and were made by the same production process, they differed from one to another, which can be a source of the variation in the measured vibration. Three human subjects participated in our experiments, which were carried out as stated in ISO 5349. The subjects were asked to maintain their posture, and the applied force was kept as constant as possible. The applied force was monitored using an indirect method, where vibration energy was displayed in real time during the experiment using a three-axis accelerometer attached to the work piece at a specified point. The appropriate range of the applied force was predetermined to cover the range of real work operations. The engineering tolerance between the inner diameter of a grit disk and the outer diameter of the tool shaft leads to an eccentricity of the mass at the center of the disk. The degree of eccentricity varies with installation, and this is another source of uncertainty. In our study, the effect of this eccentricity was investigated by carrying out repeated assembly and disassembly of an insert.

Jan 6, 2006

By Horst Peter Wölfel

The goal of biodynamic models is to simulate the vibration behaviour of the human body. In combination with experimental studies biodynamical models can be a powerful tool for the analysis of the effects of vibration exposure on health [1] and comfort. This paper gives an overview of the state of the art of biodynamic whole-body vibration models of humans, addressing both numerical models and hardware dummies. Method Two approaches are distinguished, the phenomenological and the anatomical, as illustrated in Figure 1. [ ] Phenomenological models aim to reproduce the vibration behaviour of humans with respect to particular physical quantities, chiefly the driving-point impedance at the interface to the seat, and partly with respect to other transfer functions. Discrete systems of masses, springs, and dampers with several degrees of freedom whose topology and parameters are determined by structure- and parameter identification methods are used in the sense that the functions derived from measurements are reproduced as well as possible. This paper provides an evaluation of this methodology and defines its range of application as well as its limits.

Jan 6, 2006

By Jack Wasserman, Don Wasserman, Logan Mullinix, Shekhar Khanal, Kelly Neal

This paper presents current finding on truck driver average exposure to acceleration for several different manufacturer’s cab-over trucks on a variety of roads in different countries. The predominant time, for this aspect of the study has been spent in the area around London, England and Warsaw, Poland. The ECE directive 2002/44/EC has provided specific guidelines for vehicle operators 8 hour average acceleration exposure. The primary considerations have been on truck design including the air-ride driver’s seat. The truck manufacturers have produced truck cabs that have some separate suspension from the truck frame. The truck seat manufacturers have been producing air-ride suspension seats for the cab. Both of these designs have had the objective of meeting the ECE directive and providing the vehicle drivers with some degrees of comfort. This paper will provide some information on the ability of the vehicles to operate on a variety of roads and meet the objectives. Method The primary method for evaluation of the driver’s exposure has been the use of a seat pad attached to the driver’s seat. Although this sensor system provides the critical information for the driver, an understanding of the reasons for the values requires additional measurements. The initial study in England used both driver and passenger seat pads, as shown in Figure 1, as well as triaxial accelerometers mounted on the base of the seat. The latest studies used significantly more transducers to better understand the relative rotations and translations on the truck frame, the cab, and the driver. [ ]

Jan 6, 2006

By Stephen E. Mosher, Suzanne D. Smith

Ground, air, and water vehicles can expose humans to substantial multi-axis vibration. Multiple input/multiple output relationships or models exist for estimating frequency response functions of linear systems1, 2. These relationships have been applied by some investigators to evaluate the effects of occupied seat vibration3, 4. Using a multiple input/single output model, this study investigated the effects of single- and combined-axis vibration in the fore-and-aft (X), lateral (Y), and vertical (Z) directions on vibration transmission to the human chest. Frequency response functions (transmissibilities) were estimated and compared for the back-on and back-off postures. Methods A rigid seat with seat back was mounted onto the Six Degree-of-Freedom Motion Simulator (SIXMODE). A flat acceleration vibration signal was generated between 2 and 40 Hz at 1.0 ms-2 rms in the single and combined X, Y, Z, XY, XZ, YZ, and XYZ axes. The signals were shifted in time so that the combined inputs were not fully correlated. Lightweight triaxial accelerometers were used to measure accelerations at the seat base (input) and at the bony manubrium of the chest (output). The maximum of nine frequency response functions (H(?)) or transmissibilities were estimated from the auto- and cross-spectra. The system transfer matrix for the XYZ inputs and chest Z output is [ ] where PxZ, PyZ, and PzZ are the cross-spectra between the three inputs at the seat base and the Z output at the chest, respectively, and Pxx, Pxy,…zz are the auto- and cross-spectra between the input signals (? not shown in Eq. 1). Equation 1 can be similarly written for the chest X and Y outputs. Matlab® was used to estimate the auto- and cross-spectral densities for calculating the transmissibilities, ordinary coherences (for single inputs), partial coherences, and multiple coherences. Results Figure 1 illustrates the major chest transmissibilities observed for the two postures. Vertical vibration showed a consistent influence on the chest X response (Chest X/Z), most likely causing chest pitch. Some chest Z responses were observed with X-axis inputs, but the results were variable and difficult to interpret. In general, other factors besides the known inputs did not affect the transmissibilities shown in Figure 1 (Repeated Measures ANOVA, P<0.05). This was

Jan 6, 2006

By Alice Turcot

Knowledge of risks from exposure to hand-arm vibrations is usually presented by clinicians and researchers from a medical and engineering point of view. There is a strong need to develop innovative health promotion programs for exposed workers. Risk perceptions by vibration exposed workers and HAVS (hand-arm vibration syndrome) affected workers are less well known. In 1983, Brubaker demonstrated that 75% of studied fellers thought that whitening of the fingers was part of the job and/or an unrelated nuisance, while only 25% believed it was a disease. 1Grounds also showed that even though there were a very high number of forestry workers with white fingers, none considered quitting because of their condition. 2 It seems that many workers hesitate to declare the illness or believe they are less affected than they really are, perhaps from fear of losing their jobs and livelihood. 3 Risk awareness, on the part of exposed workers and their employers, as well as knowledge and acceptance of available preventive solutions are necessary steps before installing adequate preventive measures, whether organizational, behavioral or environmental. Workers need to understand fully the hazards and risks in order to be able to make informed decisions under uncertain conditions.4 Prerequisites include the following: workers knowledge about the risk, their attitude towards it, which in turn, can be influenced by values, needs and interests. Also, knowledge and attitudes towards safety behaviour, organizational or environmental barriers must be taken into account. Our research focuses on these key elements, which help bridge the gap between health promotion research and practice. Methods A descriptive exploratory study is in progress with workers exposed to hand-arm vibrations. It uses qualitative methods that include focus group discussions with workers exposed to hand-arm vibrations, as well as individual interviews with other key informants (employers, health care professionals). An open-ended questionnaire was developed to collect qualitative data on perceived risks and solutions to prevent or reduce HAVS. Based on an integrated theoretical framework related to known determinants of behavior change, the analysis will focus on the following5: 1) knowledge of health effects, safety, well-being and/or quality of life 2) related beliefs about individual susceptibility and severity of consequences 3) attitude and values related to hand-arm vibration exposure 4) knowledge and attitudes towards exposure reduction, as well as perceptions of barriers and facilitating factors for these measures, in the workplace environment or otherwise.

Jan 6, 2006

By Pramod C. Thakur

In This Chapter [Origins of coalbed methane Reservoir properties of coal seams Thresholds for coal seam degasification Methane emissions in mines Methane drainage techniques How to transport gas safely in mine pipelines and Economics of coal seam degasification Recommended publications on coal seam degasification are Gas Control in Underground Coal Mining [Creedy et al. 1997], Coalbed Methane Extraction [Davidson et al. 1995], and Methane Control for Underground Coal Mines [Diamond 1994].] ORIGINS OF COALBED METHANE AND RESERVOIR PROPERTIES OF COAL SEAMS Origins of coalbed methane. Coal seams form over millions of years by the biochemical decay and metamorphic transformation of plant materials. This coalification process produces large quantities of byproduct gases, such as methane and carbon dioxide. The amount of these byproducts increases with the rank of coal. It is the highest for anthracite, where for every ton of coal nearly 1,900 lb of water, 2,420 lb (20,000 ft3) of carbon dioxide, and 1,186 lb (27,000 ft3) of methane are produced [Hargraves 1973]. Most of these gases escape to the atmosphere during the coalification process, but a small fraction is retained in the coal. The amount of gas retained in the coal depends on a number of factors, such as the rank of coal, the depth of burial, the type of rock in the immediate roof and floor, local geologic anomalies, and the tectonic pressures and temperatures prevalent at that time. The gases are contained under pressure and mainly adsorbed on the surface of the coal matrix, but a small fraction of gases is also present in the fracture net-work of the coal. Methane is the major component of gases in coal, comprising 80%–90% or more of the total gas volume. The balance is made up of ethane, propane, butane, carbon dioxide, hydrogen, oxygen, and argon.

Jan 6, 2006

By Douglas D. Reynolds

Intense vibration can be transmitted to the hands and arms of workers who use hand-held percussive or vibrating devices, tools, and work pieces. Continued habitual exposure to vibration directed to the hands can cause patterns of various symptoms associated with hand-arm vibration syndrome (HVAS). The International Organization for Standardization (ISO) first published ISO 5349 in 1986.3 This standard specified methods for measuring and evaluating vibration directed into the hands from hand-held vibrating devices, tools, and work pieces. The American National Standards Institute (ANSI) published ANSI S3.34 the same year.1 This standard was modeled after ISO 5349-1986 and specified methods for assessing exposure to hand-arm vibration. The Parliament of the European Union has issued the European Union Human Vibration Directive-2002/44/EC, which specifies vibration daily exposure action values (DEAV) of 2.5 m/s2 and daily exposure limit values (DELV) of 5.0 m/s2. These values have generally been accepted by medical experts, scientists, and engineers in governmental agencies, research institutions, and industry in the USA and other countries.2 When they are achieved, they will reduce the potential for the development of symptoms related to HAVS among workers exposed to hand-arm vibration. Significant improvements in measurement and analysis instrumentation, miniature and subminiature accelerometers, and medical diagnostic and assessment protocols have being introduced since 1986 when ANSI S3.34 was first published. In response to these improvements and the introduction of the EU Human Vibration Directive, ANSI Working Group S2.39 developed the revision to ANSI S3.34, which has now been published as ANSI S2.70-2006.2 Method ANSI S2.70 specifies the use of the hand-arm vibration measurement procedures outlined in ISO 5349, Parts 1 and 2.2,4,5 It requires the measurement of ISO frequency-weighted acceleration values in three mutually orthogonal axes of vibration. These values are then vectorially added to obtain the vibration total value, ahv: [ ] where ahwx, ahwy, and ahwz are the measured r.m.s. ISO frequency-weighted acceleration values in the x, y, and z directions, respectively. If multiple vibration exposure events are experienced during a work day, the overall vibration total value is obtained from: [ ] where ahvi is the vibration total value of the ith operation, Ti is time duration in hours of the ith operation, n is the total number of operations, and T is total time in hours associated with the n

Jan 6, 2006

By Janine Pierce, Robert Larson, Christine Raasch

The vibration and impact environment for crew members on locomotives has been investigated in a series of studies conducted by Exponent Failure Analysis Associates (Exponent) beginning in 1990. Locomotive cab vibration and impact levels were measured on a variety of locomotive models operating over many different track sections across the Union Pacific, Burlington Northern Santa Fe, CSX, Norfolk Southern, and CONRAIL systems. The comfort and health implications of exposure to the measured locomotive vibration levels were evaluated by comparison with the human vibration exposure boundaries given in the International Standards Organization (ISO) standard 2631-1:1997, the British Standard 6841:1987, European Union (EU) Directive 2002/44/EC, measurements made by Exponent on various commercial and recreational vehicles, and vibration exposure measurement data found in the literature. Methods Initially, vibration levels experienced by locomotive crews were measured and recorded at incremental speeds covering the range of normal train operation. In 2003, a method of measuring the vibration exposure continuously by means of a digital recorder was developed, allowing the vibration level over the entire run or crew shift to be analyzed. For each seating location measured, acceleration was recorded on the seat surface beneath the ischial tuberosities (pelvis) of the seated crew member and on the cab floor directly under the seat. At each of the locations, triaxial accelerometers were used to measure the vibration along the longitudinal, lateral, and vertical axes. Since the vibration environment varies throughout the route, and locomotive vibration levels have been found to be primarily speed dependent, a speed sensor was used to continuously measure the speed of the train. To evaluate the recorded vibrations levels, the data was divided into two-minute segments, which were each processed per the 1997 ISO standard for weighted RMS vibration levels and Vibration Dose Values (VDV). Additionally, PSDs and 1/3 Octave RMS values were calculated to determine the frequency content of the vibration. For each two-minute segment, the average speed of the locomotive was calculated to allow for correlation with the recorded vibration exposure values. The resulting exposure values for the entire run were calculated by combining the data from all of the two-minute segments. Since introducing the continuous method of recording acceleration, 23 seating locations have been recorded on 11 locomotives traveling 11 different routes across various parts of the United States. One of the routes was a shift of ‘yard work’, traveling back and forth in a rail yard coupling train cars together. Results A guide to interpreting weighted acceleration values with respect to health is given in Annex B of the 1997 ISO standard. A health guidance caution zone is defined to indicate the

Jan 6, 2006

By Hideo Ando, Yuka Satou, Tatsuya Ishitake

Whole-body vibration occurs when the body is supported on a surface which is vibrating. Occupational exposures to whole-body vibration mainly occurs in the transportation industry, but also in association with other industrial process. Epidemiological studies have frequently indicated an elevated health risk for the spine in workers exposed to whole-body vibration. With regarding to train or bus operators, a fall of drivers’ wakefulness level because of fatigue is often pointed out. This decrease in wakefulness results in an increase of the occurrence of accidents. However, a study of how whole-body vibration affects people&apos;s level of wakefulness has not been done. To test the hypothesis that exposure to whole-body vibration has a certain effects on level of wakefulness, the change of a subjective wakefulness level and changes of electroencephalogram (EEG) were observed under experimental exposure to short-term whole-body vibration. Methods Subjects are ten healthy male university students, with an average age of 20.7 ± 1.8 years old, and they are all nonsmokers. Using the equipment (CV-300, AKASHI) of whole-body vibration generator, we consider an exposure environment of actual driver work, so that set the frequency and the acceleration level as 10 Hz and 0.6ms-2 r.m.s.. The subjects were exposed to whole-body vibration in the seated position and exposure time was fixed for 12 minutes. Subjective wakefulness level was evaluated using the questionnaire of VASS (Visual Analog Sleepiness Scale) and KSS (The Kwansei Gakuin Sleepiness Scale). For the electroencephalogram (EEG) measurement, it was equipped with the electrodes based on the International ten-twenty electrode system (C3-A2, O1-A2, O2-A1). EEG activity in the alpha frequency band (8 – 12 Hz) is one of the most typical physiological indicator which represent the transition from wakefulness to sleepiness. AAT (Alpha Attenuation Test) which repeats three times each opened and closed eye for 1 minute was performed in a seating position with directions of the researcher in the beginning, in the middle and in the end of exposure to whole-body vibration. For analysis, power spectral analysis was conducted over the last 6 min of EEG, and wakefulness levels were defined as the ratio of mean alpha power during eyes closed versus eyes opened. The laboratory was kept at room temperature (21 ± 1.0 degrees C), humidity was 50 ± 5%, noise level was 63.6 dB (A) eq, and illumination 510 lx. Each experiment was started around 10:00 am to minimize the effect of biorhythm.

Jan 6, 2006

By Fred N. Kissell, Andrew B. Cecala

In This Chapter [Where methane is emitted at longwall faces Where methane accumulates at longwall faces Using the modified shearer-clearer to eliminate ventilation eddy zones Using a walkway curtain to reduce methane buildup during the headgate cutout Control of frictional ignitions and The best location for the methane monitor] The methane released along a longwall face represents only 10%–20% of the total methane emitted from the entire longwall panel. Nevertheless, in very gassy coal seams, this methane released at the face can pose a problem because the shearer is a ready ignition source. Preventing methane ignitions at longwall faces requires four actions. The first is to provide better ventilation around the shearer to eliminate the ventilation eddy zones at the drums where methane builds up. These eddy zones are eliminated by mounting additional water sprays on the shearer to direct air into them. The second action to prevent methane ignitions is to install a water spray behind each cutter bit and regularly replace worn bits. Water sprays behind each cutter bit act to quench the hot metal streak that follows a worn bit when it strikes rock. The third is to ensure that no ventilation eddy zones are inadvertently created by poor placement of water sprays. The fourth is to ensure that the methane monitor on the shearer is in the best location to detect methane accumulations. ADDRESSING METHANE ACCUMULATIONS AT LONGWALL FACES3 Cecala et al. [1985a, 1989] and Denk and Wirth [1991] studied methane emission and ventilation patterns at longwall faces to find where methane accumulations are most likely. Although not always the case, the major source of methane at longwall faces is usually the breakage of coal by the shearer. Stress-related fracturing of the coal seam at the face, called bumps or bounces, can cause the release of additional gas (Figure 4–1).

Jan 6, 2006

By Claud Johnson, Kristine M. Krajnak

Vibration transmitted to the upper limb by the chronic use of hand tools can result in cold-induced vasospasms finger blanching and cyanosis, similar to that seen with Raynaud’s phenomenon (4). These vasospasms, commonly referred to as vibration white finger (VWF), are in part the result of an increased sensitivity of peripheral arteries to the vasoconstricting effects of norepinephrine (e.g., (1-3)). However, alterations in vasodilating factors could also contribute to vasospasms. The goal of these studies was to determine if exposure to a single bout of vibration alters concentrations of the vasodilator, nitric oxide (NO), in a rat tail model of vibration. To determine if vibration exposure alters NO, we exposed animals to a single bout of vibration and measured concentrations of the synthetic enzymes, nitric oxide synthetase (NOS)-1 and NOS-3 in the ventral tail artery. We also directly assessed arterial concentrations of NO using a nitrate/nitrite assay. Methods General apparatus. Animals were placed in Broome-style restrainers, and their tail was secured to a vibrating or stable platform. Rats were exposed to a single 4 h bout of tail vibration (125 Hz, acceleration of 49 m/sec2 r.m.s.) or restraint control. Animals were euthanized with an overdose of pentobarbital (100 mg/kg) and the ventral tail artery was dissected and frozen. Experiment 1: Male Sprague Dawley rats (6 weeks old, n = 32) were used for all exposures. All animals were maintained in AAALAC accredited facilities, and all procedures were approved by the NIOSH Animal Care and Use Committee, and were in compliance with the CDC Regulations for the Care and Use of Laboratory Animals. Animals were euthanized 1 or 24 h after the completion of the exposure. Western analyses were performed on total proteins (80 µg/lane) isolated from the C16-18 artery segments. Band densities were detected by chemiluminescence and quantified using Scion Image, and analyzed using 2-way ANOVAs. Experiment 2. Nitrate/nitrite concentrations.. Male Sprague Dawley rats (n = 24, 6 weeks of age) were maintained and exposed as described above. All animals were euthanized 24 h after the exposure and the ventral artery was collected. Nitrate/nitrite concentrations were measured in ventral artery tissue homogenates using the nitrate/nitrite colormetric Assay Kit (Caymen). Results Analyses of band densities revealed that there was an effect of time (F(1, 17) = 6.03, p < 0.03) on NOS-1 protein in arteries exposed to vibration, with NOS levels being lower in arteries collected 24 h after the exposure than arteries collected 1 h after the exposure. Although NOS-1 proteins concentrations were slightly lower in control arteries collected 24 h after an exposure than arteries collected 1 h after exposure, post-hoc contrasts indicated they were not significantly different than 1 h controls. In contrast, NOS-1 band densities from arteries collected 24 h after the exposure were lower than those collected 1 h after the exposure (p < 0.01; Figure 1). NOS-3

Jan 6, 2006

By Michael J. Sapko, Kenneth L. Cashdollar

In This Chapter [Methane ignition as initiation source for much larger secondary coal dust explosions Rock dusting requirements to prevent coal dust explosions Dangers of hybrid mixtures of methane and coal dust] Although methane explosions are dangerous, those that involve coal dust are even more so. If exploding methane disperses and ignites the coal dust that has accumulated on the mine ribs and floor, the burning coal dust immeasurably increases the strength of the explosion. Such methane-dust explosions are prevented by inerting the coal dust in a way that prevents the exploding methane from igniting it. This chapter discusses the dust hazard and how it is pre-vented in U.S. coal mines. METHANE IGNITION AS INITIATION SOURCE FOR MUCH LARGER SECONDARY COAL DUST EXPLOSIONS The typical scenario for coal mine explosions starts with the ignition of a flammable methane-air atmosphere near the face. The turbulent winds from the primary methane explosion then disperse the coal dust. If there is insufficient rock dust (usually limestone), a secondary coal dust explosion then propagates throughout large sections of the mine. These scenarios have been studied extensively at the Bruceton Experimental Mine (BEM) and the Lake Lynn Experimental Mine (LLEM) of the NIOSH Pittsburgh Research Laboratory. The minimum quantity of methane required to initiate a coal dust explosion was studied in 1930 in the BEM [Rice et al. 1933; Nagy 1981] and then later in the LLEM, whose cross-sectional area (130 ft2) is over twice that of the BEM [Sapko et al. 1987a]. Studies conducted in the BEM closely simulated conditions that existed in operating mines in the early 20th century. The later tests in the 20-ft-wide entries of the LLEM simulated the geometries of modern mines with advanced roof support technology. The data from the BEM tests show that 13 ft3 was the minimum quantity of methane at the face that, when ignited, would disperse and ignite coal dust. In the BEM, this amount of methane was mixed with air to form a total flammable volume of about 140 ft3 of a 9% methane-in-air mix-ture. In the wider entries of the LLEM, about 37 ft3 of methane was required to disperse pure coal dust and start a self-sustained coal dust explosion. This amount of methane was mixed with

Jan 6, 2006

By Danny A. Riley, James R. Sanger, Hani S. Matloub, Michael Agresti, David Rowe, Lin-Ling Zhang, Yuhui Yan, Paula Galaviz, Judith Marchant-Hanson, Ji-Geng Yan

Until now there has been controversy about which tests should be performed to diagnose early Hand-Arm Vibration Syndrome (HAVS). Initial screening questions, especially about tingling and numbness, routinely given to patients prior to examinations proved to be a very important tool in the diagnostic process1, 4. However, standardized tests that are simple, quick, valid and reliable are needed to support a diagnosis of HAVS. Purpose: To find the most valid and reliable tests to diagnose HAVS. Material and Methods Five major tests were performed on Group I and Group II. Group I: Control group of 12 volunteers including students, nurses, secretaries and physicians with no history of using vibrating tools (age 20 to 50y, mean age 38.5y; 5male, 5 female.) Group II: 12 workers (age 17 to 65y, mean age 39y; 9 male, 3 female) were sent by a local trade union with a history of using vibrating power tools on their jobs for varying amounts of time (mean 12.2y, from 0.5 to 35y.) Pre-enrollment survey showed that each had more than 4 complaints commonly associated with use of vibrating tools (including numbness, tingling, weakness, pain, finger color or nail changes, temperature change, and difficulty moving.) 1. Sensory nerve conductive tests: Amplitude and nerve conductive velocity (NCV) were evaluated. 2. Cold Stress-Temperature recovery time tests were done on the index finger of the dominant hand following these steps: Confirm water bath is within 4-5º C. Place the finger temperature probe on pad of the index finger of the dominant hand. Record temperature every 15 seconds. Place subject’s hand in the cold- water bath for exactly five minutes. Record temperature every 15 seconds for ten minutes. 3. Blood test: Venous blood was taken by a 21-gauge needle with the yellow collection tube adapter. S-ICAM, Sera Thrombomodulin, Norepinephrine levels were evaluated by Henderson Research Centre, Canada. 4. Finger Sensory Evaluation: Semmes-Weinstein monofilament test and 2-point discrimination tests were performed on bilateral fingers. 5. Digital blood pressure test: blood pressure was measured in bilateral index fingers. Results 1. Median nerve sensory conductive amplitude from palm to wrist : GI: mean 96 ± 31µm; GII: mean 43± 30µm; for dominant hands. GI vs GII: P<0.001

Jan 6, 2006

By Claud Johnson, G. Roger Miller, Kristine M. Krajnak, Stacey Waugh, Oliver Wirth

Workers exposed to vibrating hand tools are at risk of developing symptoms such as cold-induced vasospasms, loss of tactile sensitivity, and loss of grip strength in the fingers and hands. These symptoms are known collectively as vibration white finger (VWF) or hand-arm vibration syndrome (HAVS). Symptoms of VWF or HAVS are in part due to repeated and prolonged peripheral vasoconstriction[1, 2]. The reduction in blood flow that occurs with vasoconstriction can result in oxygen deprivation (hypoxia) in soft tissues, such as nerves and muscle, and lead to functional and structural changes in these tissues. The present study examined muscle tissue to determine if vibration-induced changes in transcript levels and protein concentrations result in enhanced vasoconstriction and hypoxia. Manual dexterity was also assessed intermittently to determine if vibration-induced changes in cellular factors are accompanied by performance deficits. Methods An animal model was developed to study the biological and functional changes that occur in response to repeated segmental vibration exposures. In this model, the right paw of intact rats was exposed to a platform vibrated at a frequency 250 Hz and amplitude of 49 m/s2 to simulate the vibration characteristics of hand-held grinders. Three groups of 8 rats each were studied: a vibration-exposed group, an exposure-control group, and a cage-control group. Exposure sessions, with or without vibration, were conducted 4 hr/day, 5 days/week for 5 weeks. Manual dexterity was assessed intermittently during the 5-week exposure period with the Montoya stair-case test[3], which quantifies the rat’s ability to reach for, grasp, and retrieve small food pellets placed below the rat on different levels or steps. Following the 5-week exposure period, the flexor muscles of the right forelimb were collected for analysis of gene expression, protein concentrations, and immunohistochemistry. Results Vibration-exposure resulted in an approximate 2-fold increase in the expression of a2C and a1D receptor transcripts in flexor muscles (Figure 1). These receptors mediate norepinephrine-induced vasoconstriction in smaller arteries. Vibration-exposure also resulted in an approximate 2-fold increase in hypoxia-induced factor-1a (HIF-1a), a transcription factor that is expressed in response to tissue hypoxia. Western analyses demonstrated that restraint caused a decrease in a1-receptor protein concentrations in the flexor, but vibration-exposure prevented the restraint-induced reduction (Figure 2). Immunohistochemistry performed on flexor muscles (not shown) demonstrated that a1 receptors are primarily located in arteries; maintained levels of these receptors could contribute to prolonged vasoconstriction following repeated vibration exposure. The staircase test showed some performance improvement, or a training effect, in manual dexterity for the control groups but not the vibration-exposed group (Figure 3).

Jan 6, 2006

By Douglas Ketcham, Thomas Jetzer

While the neurological and vascular aspects of Hand-Arm Vibration Syndrome (HAVS) has been generally accepted as a medical condition, the medical criteria and the clinical findings used to establish the diagnosis has been more difficult to bring to consensus. The criteria was first quantified by the Taylor-Palmear scale.1 This criteria was subsequently modified in 1986 at the 1st Stockholm Workshop2,3 to included more acceptance for the neurological effects that characterized the predominate findings in some workers. The relationship between hand-arm vibration and Carpal Tunnel Syndrome was defined in NIOSH 97-1414. While the aforementioned documents have defined the clinical entities associated with hand-arm vibration exposure, agreement on the clinical findings and test to confirm the diagnosis has be been more difficult to bring to consensus. Clinicians assessing HAVS has relied on a number of varied neurological and vascular tests. The neurological testing has focused on assessing damage to the sensory capability of the fingers for the neurological component including tests to measuring ability to sense vibration, cold or other end point finger sensor functions. However, the vascular testing has been traditionally focused on the ability to either measure vascular function or to reproduce the vascular blanching that occurs in HAVS with cold water provocation. Recent assessment of this testing in the United Kingdom Coal Miner’s study has questioned the value of this testing especially in reviews by McGeoch.5 In an attempt to provide some type of definitive testing to substantiate vascular damage from hand-arm vibration exposure, angiography is an alternative or adjunct to cold water provocation testing. The standards that have been established to predict the level, type and incidence of HAVS have been based on clinical studies and reports that have essentially been all male populations. However, the recent entry of women into more vibration intensive jobs has brought about the exposure of some women to high levels of vibration previously only previously experienced by men. However, there have been only few studies that look at HAVS in women6. Although exposed the same vibration levels, it has not been clear that the latency and type of pathology of HAVS in women will be the same as for men. The purpose of this study is to look at recent case studies of men and women exposed to jobs with high levels of hand-arm vibration with extensive clinical testing for both the neurological and vascular components of HAVS as well as other associated upper extremity conditions such as Carpal Tunnel Syndrome.

Jan 6, 2006

By Richard Stayner

Suspended seats perform two functions: Reduce effect of occasional large bumps; Reduce more continuous vibration at a lower level. The former needs high damping. The latter needs low damping. For most mobile work machines the inevitable compromise is generally better than a simple cushion seat, because that amplifies vibration at around 4 Hz which is a sensitive frequency for human vertical WBV. Why have standard tests for seat suspensions? • Seat suspensions are non-linear so any measure of performance depends on operating conditions. For comparison these need to be defined. • Seat manufacturers need benchmarks for product development; • Machine makers choose dynamic characteristics appropriate to their products; • Occupational health specialists wish to control operator exposure to Standard tests should be representative, repeatable and reproducible. These requirements are reviewed in relation to the history of seat test standards and the current position. Current position and history The current position is that we have standard tests for seats for agricultural tractors, earthmoving machinery, industrial (fork-lift) trucks. These tests comprise measurement of vibration transmission and of the rate of damping. Current standards developed as the technology developed, starting around 1960: 1. Test on machine driven over standard surface1. 2. Test on shaker reproducing standard surface. 3. Shaker input replaced by representative spectrum2. 4. Human subject replaced by dynamic dummy. (Not yet settled). Are standard tests representative? The development process has gradually moved seat tests further from reality. 4 hr samples of work exposure suggest that seats do not on average provide large reductions of vertical WBV3. For specific magnitudes of vibration they can work well. For low vibration, performance is reduced by friction and for severe vibration by length of travel. Recent work has led to a new test to quantify how a suspension controls over-travel 9.

Jan 6, 2006

By Magnus Persson

ISO8662-4, “Hand-held portable power tools - Measurement of vibrations at the handle - Part 4: Grinders” is under revision. The new revision shall harmonize ISO 20643 “Mechanical vibration - Hand-held and hand-guided machinery - Principles for evaluation of vibration emission” which, among others, requires measurements in three directions and declared values related to the upper quartile of real-use vibration. To get the most suitable test method, a round robin test was made for evaluation of the two test methods proposed by the ad-hoc group working with this standard revision. Methods Seven laboratories measured the vibration from four grinders of different sizes, with and without autobalancing units. The laboratories come from universities, health & safety laboratories and grinder manufacturers. Two measurement methods are evaluated with respect to repeatability and reproducibility: 1. Grinding on a well-defined mild steel bar with depressed center wheels according to detailed test instructions. The test sequence starts and ends with 10 seconds of running the grinder in the air, when measuring the unbalance contribution to the vibration coming from the unbalance of the grinding wheel. Between these runs the average vibration during 60 seconds of grinding is measured. Three operators do five grinding tests per grinder. 2. Measurements using an aluminum unbalance disc similar to the one defined in ISO8662-4. Each operator runs the grinder four times, between each run the unbalance is moved 180 degrees to avoid variations caused by the play between the test wheel and the spindle. The averaging time is 10 seconds. Each grinder is tested by three operators. Repeatability is the spread within a lab between operators and over short time period for one machine and reproducibility is the spread between laboratories and over longer time periods for one machine. Instrumentation and transducer location are chosen according to ISO8662-4 and circulated test instructions. Results Both the repeatability and reproducibility is poor for the real grinding test, see figure 1. The coefficient of variation for repeatability is approximately 40% higher for the grinding test and the coefficient of reproducibility is 60% higher for the grinding test than for the unbalance disc test.

Jan 6, 2006

By Stephen L. Tillim

Tubular Handles can negatively affect the contents of the carpal tunnel. Years of injuries from grasping handles for tools and machines can cause carpal tunnel syndrome, tendonitis and wrist joint injuries. The can cause inability to use a hand and resulted in the longer absences from work than injuries from falls, accidents or fires.1 Cylindrical, tubular and rectangular handles are rolled flat structures. They place the hand on a rolled flat surface where the ends of the middle and ring fingers overlap the index and small fingers. They are pulled along a series of lines that contact the end joint of the index finger, the middle bones of the middle and ring fingers and the end bone of the small finger. Cylinders are pulled diagonally in the hand toward the carpal tunnel (CT) area. Gripping in this manner tenses asymmetric muscle groups in the forearm. Handles could work better if they do not place pressure on the CT and conform to the natural function or neutral hand position where the hand rests or dangles at the side of the body, the finger tips form a diagonal, the palm and fingers form a cup, the thumb rests between the index and middle fingers and the wrist is mildly extended. However, handles designed for the neutral position are pulled by diagonally oriented fingers into the valley between the thenar and hypothenar muscles where they can compress the median nerve and tendons exiting the CT. Seven principles for handles that do not place pressure on the carpal tunnel and employ optimal hand position are presented. First, handles should align the ends of the fingers parallel to the horizontal crease and not diagonally. Second, handles should extend from the cupped fingers to meet the muscles at the base of the thumb on the radial side of the hand and extend further on the other or ulnar side to meet a portion of the small muscles. Third, handles should have a recess on the proximal side to prevent contacting or placing pressure on the carpal tunnel. Fourth, handle design should be based on hand measurements in a position of function. Fifth, handles should come in sizes. Sixth, handles should be placed on tools to maintain the wrist and elbow in neutral position. The seventh is handles should support the maximum area of the hand and absorb, but not direct, vibration to the carpal tunnel. These principles led to prototypes and patents for handles for gripping, pinching and squeezing2,3,4 . The poster will illustrate and explain the principles Bonsil handles. Research, with existing tools, is needed to substantiate claims made for the Bonsil handle.

Jan 6, 2006

By G. Roger Miller, Kristine M. Krajnak, Stephen S. Leonard, Stacey Waugh

Repeated exposure to hand-arm vibration through the use of vibrating hand tools can result in the development of the disorder known as hand-arm vibration syndrome (HAVS; (1,3)). One of the hallmark symptoms of HAVS is cold-induced peripheral vasospasms that result in finger blanching (4). Although the vascular and neural pathology associated with vasospasms has been described, little is known about cellular mechanisms leading to this damage (4). To understand how vibration may alter vascular and neural physiology and anatomy, rats were exposed to a single bout of tail vibration and the molecular responses of neural and vascular tissues were measured to determine if there are immediate or sustained affects of vibration that may underlie longer term changes in physiology. Methods Experiment 1. Male Sprague Dawley rats (n = 32, 6 weeks of age) were housed in AAALAC accredited facilities. All procedures were approved by the NIOSH Animal Care and Use Committee and were in compliance with the CDC guidelines for care and use of laboratory animals. Vibration exposures were performed by restraining rats in Broome-style restrainers, and securing their tails to a vibration platform using 6 mm wide straps that were placed over the tail every 3 cm. Restraint control rats were treated in the same manner, except that the tail platform was mounted on isolation blocks and not on a shaker. The vibration exposure was 125 Hz, 49 m/s2, for 4 h. Rats were euthanized with an overdose of pentobarbital (100 mg/kg) 1 h or 24 hours after the exposure. RTqPCR was used to measure transcript levels for endothelin 1 (ET-1), the 3 forms of nitric oxide synthetase (NOS) NOS-1, NOS-2, NOS-3 and norepinephrine receptor subtypes 1D, 2A, 2C, in artery tissue, and to measure calcitonin gene-related peptide (CGRP) and nitric oxide synthase-1 (NOS-1) in ventral nerves. Data were analyzed using 2-way ANOVAs. Experiment 2. Male Sprague Dawley rats (n =24, 6 weeks of age) were maintained as described above. Animals were exposed to a single bout of restraint or vibration. Another group of animals served as cage controls. All animals were euthanized 24 h after the exposure, and tail arteries were isolated and frozen. Reactive oxygen species ROS) were measured using electron spin resonance spectroscopy (ESR). Arteries were homogenized over ice in 1 ml of PBS with protease inhibitor cocktail, using a tissue tearer (Biospecs Products Inc. Racine, WI USA). The sample was split into two 0.5 ml samples. One set had PBS and the spin label hydroxyl-TEMPO [0.1 mM] added while the other set had hydroxyl-TEMPO [1.0 mM] plus the specific hydroxyl radical scavenger, dimethylthiourea (DMTU), added to confirm the presence of the hydroxyl radical. Samples were vortexed and then placed in a flat cell for ESR analysis. The ESR spectrometer settings were: receiver gain, 6.32 x 102; time constant, 0.02 s; modulation amplitude, 1.0 G; scan time, 20 sec; magnetic field, 3490 ± 100 G (2). Data were analyzed using 1-way ANOVAs.

Jan 6, 2006

By Michael J. Jorgensen, Anoop Polsani, Khurram S. Khan

Riveting operations in aircraft manufacturing involves the use of power tools for manually drilling holes for the rivets, power drills for the setting of the holes for the rivets, as well as rivet guns to drive and set the rivets. To close the rivet, the rivet is driven against a metallic bar commonly called a “bucking bar”. The bucking bars are typically held firmly to increase the quality of the riveting, as well as keep the bucking bar from “dancing” against the metal piece being riveted. Thus, employees in aircraft manufacturing involved in riveting are exposed to hand-arm vibration from several sources, and epidemiological evidence suggests that vibration-related musculoskeletal disorders are associated with long term exposure to riveting tasks in the aircraft manufacturing of aircraft.1,2 Recently, tungsten technology has been introduced into aircraft manufacturing for bucking bars, which are heavier than traditional steel bucking bars of the same size. Rivet guns with tungsten pistons instead of steel pistons have also recently been introduced with the objective of reducing vibration exposure to the riveter. The objective of this study was to assess vibration characteristics of steel and tungsten bucking bars and rivet guns to identify the combination that simultaneously reduced the combined exposure to both the “riveter” and “bucker”. Methods Vibration (10g tri-axial accelerometer, Biometrics S2-10G-MF Series 2) was measured from eight experienced employees using seven different rivet guns on size 6 rivets, with the same person bucking for all subjects. Vibration was also measured on two different bucking bars for these same eight subjects, with the same person driving the rivets using the various rivet guns. The rivet guns consisted of three E4 steel piston guns with different RPMs (Guns A-E4, B-E4, C-E4), an E4 vibration dampened rivet gun (Gun D-E4D), an E3 steel piston rivet gun (Gun E-E3) and an E3 and E4 tungsten piston rivet guns (Guns F-E3T and G-E4T). The bucking bars were made of 90% tungsten (1694g) and cold-rolled steel (843g), and were the same shape and size. A two-way repeated measures analysis of variance was performed on the vibration (mean frequency weighted resultant acceleration) on both the rivet gun side and the bucking bar side, and mean rankings were used to assess the vibration simultaneously for the rivet gun and bucking bars to investigate which combinations provided the lowest vibration exposure. Results Frequency weighted resultant acceleration was significantly lower on the E3 tungsten (F-E3T) rivet gun than the E4 steel piston (B-E4) and the E4 tungsten piston (G-E4T) rivet guns (Figure 1). When measuring vibration on the bucking bar, the E4 (A-E4) steel piston rivet gun resulted in lower vibration on the bucking bars than the E4 tungsten piston (G-E4T) and E4 vibration dampened (D-E4D) rivet guns (Figure 2). Additionally, use of tungsten bucking bars resulted in a 35% decrease in resultant frequency weighted acceleration than when using steel bucking bars.

Jan 6, 2006