Search Documents

By Forrest T. Moyer

Injury experience in the coal-mining industry was worse in 1965 as both the frequency and severity rates of injuries increased 2 and 6 percent, respectively, over comparable data for 1966 (tables 1-8). The retrogression in the safety record during; 1965 resulted frog the less favorable record at bituminous-coal mines, which more than offset the improved injury experience at anthracite mines. The 259 fatal and 11,138 nonfatal injuries occurred at a rate of 45.77 per million man-hours of exposure and resulted in a severity rate of 8,960 days lost per million man-hours. Although the number of fatalities was the second lowest annual total in the recorded history, it was 17 higher than in 1964. At anthracite operations the total of 6 fatalities in 1965 was the lowest annual figure in statistical history. The annual numbers of nonfatal injuries at ill coal mines and the resulting rates of occurrence have varied little in the past 5 years (table 1). The total days lost from all injuries rose from 2.1.3 million in 19b4 to 2.23 million in 1965 (table 5). Fatal and permanent total injuries, with a standard time charge of 6,000 days each, accounted for 1,650,000 days; Permanent partial injuries, 191,932 clays; and temporary total disabilities, 383,911 days. The severity rate for fatal injuries was 6,241, 8 percent higher than in 1964, and the nonfatal severity rate of 2,718 days lost per million man-hours was 2 percent higher than in the preceding year. The average severity of permanent partial injuries ire; 730, or 48 days fewer per injury than in 1964. The average days lost for each temporary total injury was 36 days in each year.

Jan 1, 1968

By E. P. Barret

Differences in the reducibility of iron oxide materials have been recognized for a long time. Limonites are deoxidized more readily than hematites, and unaltered magnetites are the most difficult to deoxidize. Sinters are found between hematites and magnetites and vary considerably in reducibility, depending on the sintering practice followed and on the degree of fusion of the product. The increased activity in the beneficiation of taconite recently has made available a new blast-furnace raw material, namely, iron oxide pellets made from magnetic taconite concentrate. Many of the data in this paper apply to these pellets, or glomerules, as they were called when this method of agglomerating iron ores was first considered. To clarify the terms applied to iron oxide materials in this paper, the following definitions are given. Agglomeration is the general term applied to all methods of compacting or consolidating fine iron oxide materials. Sinter is the product from a Dwight-Lloyd or Greenawalt sintering machine. Pellets are formed by balling fine, moist oxide in a rotating drum at room temperature, followed by heating in a shaft furnace to a temperature below that of incipient fusion to develop a permanent bond. Nodules are formed by heating the iron oxide material to incipient fusion in a rotary kiln. Briquets are formed in a mold under pressure, with or without the addition of a binder, and burned to develop a permanent bond.

Jan 1, 1949

By Michael J. Brnich

On November 20, 1968, a massive explosion rocked the underground workings of Mountaineer Coal Co.?s Farmington No. 9 Mine in West Virginia. Of the 99 miners who were working in the mine at the time of the explosion, only 21 survived and escaped the mine. This group included eight who were rescued from the Mahan?s Run air shaft. Nearly 40 years after the event, researchers from the NIOSH Pittsburgh Research Laboratory conducted oral history interviews with two of the eight survivors rescued from the shaft. The Farmington No. 9 Mine disaster ultimately led to passage of the Federal Coal Mine Health and Safety Act of 1969 (amended in 1977).

May 1, 2009

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

3. Application of Proposed Revised Standards 57.11-50 to Mines Surveyed 3.1 Subparagraph (a) 1 "Each mine shall have at least two separate and properly maintained escapeways from each working place to the surface which are so positioned that physical or environmental damage to one will not lessen the effective¬ness of the other, and which meet the requirements of travelways and man hoisting standards These escape¬ways shall reach to within 1000 feet horizontally or 300 feet vertically of each working place " 3. 1. 1 Discussion This section will deal with the 1000 and 300 feet distance requirements, Section 3. 5 will deal with the "environmental damage" provisions. During the course of the mine surveys, it became obvious that one mine's 1000 foot distance was nowhere near equal to another' s --not in the actual distance but in the time required to traverse that distance. This -Ls true for the 300-foot requirement as well. The most obvious example is that one could traverse down a 300-foot raise much faster than climbing up the same distance. The temptation is strong to recommend that the distance requirement be changed to travel times instead. However, this approach would unfortunately lead to a lot of subjective evaluations. Having a time requirement for an entire mine evacuation (Subparagraph 6) is one thing, time requirements and the requisite inspection proce¬dures for each working place are quite another.

Jan 1, 1976

By H. M. Thorne

The Petroleum Experiment Station of the Bureau of Mines at Laramie, Wyo., in cooperation with the University of Wyoming, has in progress chemical and refining studies of Wyoming black oils. In general, these crude oils are characterized by their high sulphur, high asphalt, and low gasoline content and are called black oils because of these properties and their color. Characteristics of the various Wyoming black crude oils, as determined by the Bureau of Mines Hempel method of analysis, have been pubished.4/

Jan 1, 1938

By Vernon C. Allison

The explosibility of coal dust has long been recognized by competent investigators as constituting one of the dangers of mining coal and in the use of pulverized coal as a fuel in industrial plants. The Bureau of Mines has carried on extensive series of experiments dealing with this subject, and has not only developed methods for the practical prevention of this danger, but in the, course of these experiments has developed a standard method of determining the relative explosibility of coal dusts and other organic dusts.3 Oil shale contains compounds 'of carbon and hydrogen that are either of a petroleum nature and are strongly ,adsorbed upon the incombustible part of the shale, or else are present in the shale as a compound ("kerogen") which has the property of changing into petroleum-like products when acted upon by heat. The oil shales may contain varying amounts of the organic matter, ranging from a trace to more than 66 per cent, depending upon their richness; therefore, it is important to know whether the dusts formed in mining and handling these oil shales are explosive when mixed with air and if so, to indicate remedial measures. This paper gives the results of explosibility tests of several pulverized oil shale's, selected as being typical of those which in the future may be used in commercial shale-oil production test on a sample of typical Colorado oil shale has been., published in an earlier paper.4

Jan 1, 1926

By P. Coleman, J. C. Kerkering, S. Iverson

Fault tree analysis is a systematic safety analysis tool that proceeds deductively from the occurrence of an undesired event (accident) to the identification of the root causes of that event. One recurring mine safety problem—a dozer falling into a void over a drawpoint on a coal surge pile—was analyzed using available, inexpensive fault tree programs on a personal computer. The analysis identified basic and intermediate events that led to the burial of the dozer and graphically depicted the interrelationship between these various subordinate events as well as the various chain of events leading up to the primary event. A sensitivity analysis on these probabilities showed which events had the greatest influence on dozer burial in a coal surge pile.

By Martin Harper

This paper concludes a five year program on research into the use of a portable X ray fluorescence (XRF) analyzer for analyzing lead in air sampling filters from different industrial environments, including mining, manufacturing and recycling. The results from four of these environments have already been reported. The results from two additional metal processes are presented here. At both of these sites, lead was a minor component of the total airborne metals and interferences from other elements were minimal. Nevertheless, only results from the three sites where lead was the most abundant metal were used in the overall calculation of method accuracy. The XRF analyzer was used to interrogate the filters, which were then subjected to acid digestion and analysis by inductively coupled plasma optical emission spectroscopy (ICP OES). The filter samples were collected using different filter holders or "samplers" where the size (diameter), depth and homogeneity of aerosol deposit varied from sampler to sampler. The aerosol collection efficiencies of the samplers were expected to differ, especially for larger particles. The distribution of particles once having entered the sampler was also expected to differ between samplers. Samplers were paired to allow the between sampler variability to be addressed, and, in some cases, internal sampler wall deposits were evaluated and compared to the filter catch. It was found, rather surprisingly, that analysis of the filter deposits (by ICP OES) of all the samplers gave equivalent results. It was also found that deposits on some of the sampler walls, which in some protocols are considered part of the sample, could be significant in comparison to the filter deposit. If it is concluded that wall deposits should be analyzed, then XRF analysis of the filter can only give a minimum estimate of the concentration. Techniques for the statistical analysis of field data were also developed as part of this program and have been reported elsewhere. The results, based on data from the three workplaces where lead was the major element present in the samples, are summarized here. A limit of detection and a limit of quantitation are provided. Analysis of some samples using a second analyzer with a different X ray source technology indicated reasonable agreement for some metals (but this was not evaluated for lead). Provided it is only necessary to analyze the filters, most personal samplers will provide acceptable results when used with portable XRF analysis for lead around applicable limit values.

Jan 1, 2007

By H. M. Harris

The Bureau of Mines investigated chlorination of domestic ilmenites in a fluidized coke bed at temperatures of 950° to 1,150° C. Objectives were to develop an effective process for producing TiC14 suitable for TiO2 pigment and to reduce pollution by collecting and treating waste byproduct chlorides. The reactor for these tests was a 10.2-cm-diam quartz tube heated externally by electrical resistance heaters. It contained coke beds of from 35.6 to 82.5 cm in depth that were fluidized by 13 to 25 l/min of chlorine. Ilmenite concentrate powders were introduced at the bottom of the fluid-bed reactor, using the chlorine gas stream as a carrier. Test results showed that greater than 90 pct of the ilmenite reacted at optimum conditions and recovery of TiC14 ranged from 95 to 99 pct of stoichiometric. A temperature-controlled cyclone was used to remove high-boiling-point chlorides such as MnCl2, MgCl2, and FeCl2, and also collected fine unreacted ilmenite and coke dust. Impure TiC14 and FeC13 were separated by collecting the, iron chloride in a condenser con-trolled at 200° C. Titanium tetrachloride vapor was cleaned by passage-through a salt-column filter followed by condensation in water-cooled and refrigerated condensers. Liquid TiC14 was purified further by well-known industrial methods to meet specifications for pigment-grade chloride. Integrated tests were conducted in which chlorine, produced by dechlorination of FeC13 with oxygen, was recycled and used directly in a fluidized-bed chlorinator.

Jan 1, 1976

By G. S. Rice

The recommendations of the Bureau of Mines on rock dusting practices are embodied, except in a few details, in the Recommended American Practice for Rock-Dusting Coal Mines to Prevent Coal-Dust Explosions, approved by the American Engineering Standards Committee. December 30, 1925. It is specified that the dust to be used is of a elm that all will pass through a sieve having 20 meshes per linear inch and that 50 per cent or more will pass through a sieve having 200 meshes per linear inch. Thus the coarsest size of dust and the minimum proportion of fine dust are specified, but the specification does not indicate whether a larger proportion of fine dust would be desirable. There have been advocates of the use of that size of rock dust of which the particles would all approach 200-mesh in fineness. Explosion tests were made in the Experimental mine in the earlier period of testing which indicated that the finer rock dust is somewhat more effective under test conditions, but not sufficiently so to Justify the cost of finer grinding of the dust; also there are some disadvantages of finer dust described hereafter.

Jan 1, 1930

By P. C. McWilliams

The Bureau of Mines investigated ground support problems in four major block-cave mines to assess the current "state-of-the-art" and to delineate areas for future research. The most significant problem is the inability of present support systems to hold moving ground. Further, as mining progresses to greater depth, this problem becomes more serious. Providing adequate temporary support capable of withstanding primary and secondary blasting is the next most significant problem. A detailed analysis of the effect of mining methods on support problems is also recommended for future research.

Jan 1, 1975

By B. W. Gandrud

In 1927 Coghill showed that there is considerable liberation of the iron oxide mineral from gangue when the Alabama red iron ores are ground to a size suitable for classification and tabling but that there is not sufficient to make possible a high extraction and a high grade of concentrate. Coghill states: High extraction and 'high grade of concentrate cannot be obtained without grinding to a size comparable with flotation or cyanide practice. If grade of concentrate be sacrificed the grinding need not be so severe. These ores slime readily during grinding, and in most instances the slimes are only slightly higher grade than the original ore. Not only do they carry a considerable percentage of the total iron in the ore, so that to reject them as tailings would result in prohibitively low extraction, but they are too fine to be amenable to ordinary methods of gravity concentration. In 1929 the Bureau of Mines published results showing that certain Alabama oolitic iron ores could be concentrated by classification and tabling after grinding, with rubber-covered rods. This selective grinding produced slimes of much higher grade than the original ore, and they were considered part of the final concentrate.

Jan 1, 1934

By R. P. Vinson, Abdurrahman Cetinbas, Joseph Cervik, M. G. Zabetakis

The effect of water infusion on the flow of methane and on the production of dust was investigated at an active face in the Pittsburgh coalbed. The average total flow of methane at the face decreased by approximately 79 percent, whereas the flow from the ribs increased about 24 percent after infusion. On the day after infusion, dust concentrations appear to have been reduced; however, the presence of large quantities of rock dust obscured the results on the following days.

Jan 1, 1972

By S. H. Lorain

"INTRODUCTION The veins of the Clark Fork district have been mined on a small scale since 1913. In May 1943, the district was examined by an engineer 3/ of the Bureau of Mines with a view to possible exploration for larger ore deposits that might be of value to the war effort. The area adjacent to the Hope, Whitedelf, and Lawrence mines was re-examined 4/ December 27, 1943. As a result, the Bureau of Mines started exploratory operations in the district during the summer of 1944 which was continued until the late spring of 1946. This report presents the data obtained from the investigation.ACKNOWLEDGEMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project' as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts the preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests."

Aug 1, 1946

By Steven J. Page

The Bureau of Mines used fiber-laden air to test two identical fibrous aerosol monitors (FAM) in order to establish the FAM-optical count correlation. The FAM is a unique instrument developed by GCA Corp. (GCA) to measure real-time fibrous aerosol concentrations. It will also respond to particulates that have sufficient shape irregularities to possess fiber characteristics such as the 3:1 length: diameter (L:D) aspect ratio. Results of the Bureau's laboratory tests showed that the FAM response is linearly correlated to concentration data obtained using the optical membrane filter count technique approved by the National Institute for Occupational Safety and Health (NIOSH), U.S. Department of Health, Education, and Welfare. A plot of the FAM-optical count correlation showed that FAM concentration readings are generally well within ±25 pct of the optical membrane filter count. Initial tests to estimate the best ratio control setting of the FAM for 5-µm fiber-length discrimination were performed using one instrument only (the ratio control setting determines the minimum threshold fiber length that will be detected by the FAM). The estimated setting was then used to correlate both FAM units. The result was a 65 pct difference in correlation between the two units. It appears that the major factor responsible for this difference was the internal adjustment of the photomultiplier detector sensitivity for each of the two FAM units.

Jan 1, 1980

By A. F. Colombo

The differences in starch demands that occur between ore types subjected to the anionic flotation of calcium-activated gangue and the range of residual starch contents expected to give the best metallurgical response were evaluated on a batch and pilot plant basis. A phenol-sulfuric acid procedure was used to determine the residual starch contents in the iron ore slurries. Three pilot plant campaigns on samples from a group of orebodies located on the Marquette Range, Michigan, showed that in the rougher flotation pulp, a residual carbohydrate range of 25 to 100 ppm, which is equivalent to a 0.5 lb/short ton spread, yielded optimum results. Concentrates assaying at least 65 percent Fe and less than 6.0 percent Si02 and containing more than 80 per-cent of the recoverable iron were obtained. Both batch and continuous research indicated that starch adsorption is calcium modulated and relatively unaffected by the fatty acid additions employed. Residual starch level is not a critical control factor, but the addition must be adjusted to about 25 to 50 ppm residual starch and kept in this range for most effective utilization of the added tapioca flour.

Jan 1, 1972

By Richard O. Kneisley

An empirical method, based on U. S. Bureau of Mines field studies in several Western U.S. coal mines, is presented for sizing gate road yield pillars. Discriminant analysis was used to generate functions separating successful from unsuccessful case studies. These functions relate the pillar width-height and extraction ratios and a pillar development factor to the Coal Mine Roof Rating System (CMRR), and are assumed to establish three criteria that other entry systems, under similar conditions, must satisfy. A program, Pillar Sizer, from user-provided inputs, generates a range of pillar sizes that meets the proposed criteria. Although the analysis is based on a sample consisting primarily of two-entry systems, the derived expressions generate pillar sizes closely agreeing with observed, two-entry and three-entry in situ pillars. It is concluded that the proposed approach should assist mine operators estimate entry system yield pillar dimensions.

Jan 1, 2010

By John R. Bradley

The available supply of fuel and power is a subject of importance at all times and particularly at this time. The following brief survey of fuel and power in the United States appraises the extent of the several primary sources of energy the approximate monthly demand, 1929-40; the chief centers of production and consumption; and shifts in the principal uses from 1929 to recent years. The period covers the boom year 1929, the years of the great depression, the more normal year 1937, the recession in 1938, the year 1939, and 1940 (which was affected by armament programs). In some instances, the data for 1939 and 1940 are preliminary. The four primary sources of fuel and power are coal, petroleum, natural gas, and water power. Wood fuel, important in some regions, and foreign trade in natural gas and hydroelectricity represent a relatively small part of the energy supply and are not considered in this study. The tonnages shown are in terms of coal, based upon the calorific or B. t. u. equivalents of the several sources of power. In practice, the usable heat or energy varies according to the type of equipment available for its use. For example, the efficiency of turbine water wheels and internal-combustion engines is much higher than that of steam plants and household-heating devices.

Jan 1, 1941

By J. D. Noll, S. E. Mischler

Measurement and sampling of diesel particulate matter in mine air presents a challenge due to the complexity of the diesel aerosol. The results of a series of tests carried out by the National Institute for Occupation Safety and Health, Pittsburgh Research Laboratory, in an underground mine were used to evaluate several measurement methods that are currently used to characterize particulate matter emitted by diesel-powered equipment. This paper presents an overview of these techniques and examples of the results along with a discussion of the advantages and information gained by each technique. The measurement methods discussed include particle size measurements using a scanning mobility particle sizer, total particulate matter measurements using a tapered elemental oscillating microbalance, a size selective sampling method for workplace and personal exposure assessment and a size-selective high volume sampling method for carbon analysis.

By D. E. Hirsch

The Bureau of Mines has developed a systematic procedure for separation, characterization, and semiquantitative analysis of high-boiling (350° to 550° C) distillates of crude oils. Isothermal and molecular distillation were used to prepare the 370° to 530° C distillate of Recluse, Wyo., crude oil. The distillate was separated into fractions by chemical treatment, silica-alumina gel adsorption, and gel permeation chromatography (GPC). The fractions were analyzed by use of GPC correlations and mass and nuclear magnetic resonance (NMR) spectrometry. The increased knowledge of petroleum composition obtained from the data will contribute to improved petroleum processing and utilization and energy conservation.

Jan 1, 1974