Search Documents

By J. B. Stephenson

The Bureau of Mines, under an interagency agreement with the Department of Energy (DOE), investigated the feasibility of hardfacing the critical surfaces of valves and similar devices by chemical vapor deposition. The purpose of this research was to increase the wear resistance of these components for use in the abrasive and erosive environment of coal gasification units. Tungsten and molybdenum coatings were produced on nickel-plated carbon steels and stain-less steels by hydrogen reduction of the metal hexafluoride at 325° to 600° C. Titanium nitride coatings were produced on low-carbon steels by the reaction of titanium tetrachloride, hydrogen, and nitrogen at 1,000° C. Titanium carbonitride coatings were produced on low-carbon steels by the reaction of nitrogen, hydrogen, and methane at 900° C. Tungsten, molybdenum and titanium nitride coatings were formed on 6-, 10-, and l2-inch (0.15-, 0.25-, and 0.30-meter) ball valve seats for evaluation in the low-Btu coal gasification pilot plant at the Morgantown Energy Research Center, Morgantown, W. Va.

Jan 1, 1979

The London Metal Exchange began its first official session of aluminum trading on Monday, October 2, LME prices based on 3-month forward contracts opened Monday at 52.4 cents per pound, fell midway through the week to 52.3 cents and ended Friday at a high of 52.7 cents. For the week, LME metal averaged 52.5 cents. Although Reynolds Metals Co. and Aluminum Co. of American continued in September to value unalloyed 99.5 percent aluminum ingot at 53 cents per pound, other producers were at higher positions of 55-57 cents. Alcan Aluminum Corp. of Alcan Aluminum, Ltd., a Canadian producer, increased prices for its U.S.-marketed ingot by 2 cents to 55 cents per pound, effective September 21. New York merchants increased ingot quotes by approximately 0.5 cents to 52.8-53.5 cents per pound.

Jan 1, 1978

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

1 14 THIS IS A DIGITAL COMPUTER SIMULATION OF THE VENTILATION SYSTEM OF A MINE LOCATED IN WASHINGTON COUNTY, PENNSYLVANIA. THE VENTILATION SURVEY ON WHICH THIS SIMULATION IS BASED WAS RUN FROM OCT. 27-30 AND ON NOV. 2, 1976 IN THE ACTIVE PORTION OF THE MINE INBY COMBS SHAFT AND THE INACTIVE PORTION AFOUND AND INBY DONAHOO SHAFT. FOLLOW-UP SURVEYS WERE THEN RUN ON FEB. 18 AND FROM MARCH 7-11, 1977 TO INCLUDE THE MAIN HAULAGE SYSTEM OUTBY THE ACTIVE AREAS OF THE MINE. ALL SURVEY DATA WAS NORMALIZED TO A STANDARD DENSITY OF 0.075 POUNDS/CU.FT. PRIOR TO THE CALCULATION OF INPUT PARAMETERS FOR THIS SIMULATION. IN THIS RUN, THE ORIGINAL VENTILATION NETWORK HAS BEEN MODIFIED TO INCLUDE NEW INTAKE AND RETURN AIRSHAFTS AT THE WEST MAINS. IN ADDITION A CONNECTION HAS BEEN MADE BETWEEN THE MINE UNDER STUDY AND A SHAFT IN A WORKED OUT MINE IN THE 1 FACE AREA. THIS SHAFT IS CONSIDERED AN INTAKE SHAFT FOR THIS RUN.

Jan 1, 1977

By C. J. Walker

The ever-increasing use off natural underground formations for storing natural gas has focused attention on the behavior of such storage formations under varying operating conditions. The need for a means of evaluating in¬dividual wells and groups of wells has become manifest. It is essential that industry and others be able to determine the rates of flow that can be ex¬pected from a given well or group of wells under different conditions and to ascertain whether certain wells are deteriorating. Such questions need more exact answers now than ever before because of the vital role underground gas storage plays in the industrial and domestic consumption of natural gas. The Bureau of Mines--in cooperation with the American Gas Association--has main¬tained an active interest in gas-well testing because of the implications of such test procedures on the consumption and efficient production of natural gas. A basis for testing gas wells was provided by the back-pressure method of Rawlins and Schellhardt (12).4/ They showed that for normal gas wells there is a consistent relationship between rates of delivery of gas and corresponding pressures when the formation pressures are used as the basis of interpretation, The equation for this relationship is as follows: Q = C (Pf2 - Ps2)n where; Q = rate of flow, generally expressed in cubic feet per 24 hours. C = a coefficient.

Jan 1, 1960

Acid pollution from abandoned mines causes serious contamination of major streams in coal mining areas. In Pennsylvania alone it is estimated that 3000 miles of streams are devoid of fish and plant life because of coal mine effluent.1 The pollution arises because water and oxygen react with iron sulfide in the mine cavity to produce sulfuric acid and iron sulfate, which later find their way back into surface streams. Two general approaches to the problem are possible: (1) prevent the acid-forming reaction from taking place, (2) treat the acid mine water after it is formed so that it will not be harmful to the ecology when discharged into streams and other surface waters. The work described in this report belongs in the first category - it was based on the assumption that acid formation in the mine cavity can be prevented by keeping water (one of the reactants) out of the mine. This was to be accomplished by-forming a waterproof seal over the mine cavity which would prevent the seepage of surface water into the mine. It was planned to form such a seal at or near the surface of the ground by applying latex to the soil. Ideally a dilute latex would be applied to the soil and would penetrate to a depth of two to three feet below the surface where it would be coagulated by reacting with a constituent of the soil or by other means., A seal below the surface of the soil would have several advantages over a surface seal - it would not be subject to destruction by traffic, frost or vegetation and, more important, it would allow the use of the top soil for many agricultural purposes. A preliminary feasibility experiment was performed prior to application for the present grant. It showed that it was indeed possible to form a sub-surface seal by means of latex. A core of soil was obtained locally (Wayne, N. J.) by driving a 6.5 cm inside diameter steel pipe about 100 cm long into subsoil for a distance of 71 cm. The soil was retained within the pipe for this experiment. A part of the free space above the soil in the pipe was charged with water, and the seepage rate of the soil after it had become saturated was 15 ml/min under a total head (wet soil plus supernatant column of water) of 92 cm. After the supernatant water had drained completely, 100 ml of 5% rubber latex was added and allowed to seep into the soil. This was followed by additional water and the seepage rate was found to be 2 ml/min under the same head. This seepage rate remained unchanged when remeasured on the following day. Since there was no visible evidence of the latex in the collected drain water it is presumed to have been retained by the soil.

Jan 1, 1972

By S. H. Ash

THE information obtained by examining and analyzing the core drillings from 15 diamond-drill holes shows that with the proper equipment little difficulty should be experienced while sinking the shafts at the 15 selected sites. Although a number of holes penetrated formations containing a high percentage of silica,, the health hazard from dust can be removed by using proper dust-control equipment. Methane was detected in small amounts in only one (hole 5) of the boreholes. The methane hazard should present no difficulty if adequate ventilation is employed while sinking the shafts.

Jan 1, 1952

The Bureau of Mines performed cratering experiments in a homogeneous granite to test scaling laws for charge weights of 0.00476, 0.0220, 0.0900, 0.304, and 1.03 lb. Agreement among the data was best when empirical scaling exponents greater than one-third were assumed. Although the analysis showed that the best empirical scaling exponents were 0.37 for crater volume, 0.38 for crater radius, and 0.39 scaling for crater depth, all three crater dimensions could be scaled with a 0.38 scaling exponent.

Jan 1, 1970

By Maria I. De Rosa

The Bureau of Mines performed experiments to determine concentrations of toxic gases and liquids, and smoke-particle diameters and diameter-concentrations evolved during degradation of PVC-derived brattice with and without nylon-woven fabrics, fiberglass, cotton, and jute brattices, and other mine materials. The samples were exposed in a 20-L chamber at temperatures of 1500 to 4500 C, with a chamber airflow of 10 L/min; 27.3 cm3/s of which was directed into a submicrometer-particle detector-analyzer. During the degradation of PVC-derived brattice, large concentrations of hydrogen chloride (TLV, 5 ppm; STEL, 100 ppm) evolved at a temperature as low as 2000 C. The minimum toxic load of 3.1 mg or 40 ppm in 50 L of dilution air, with O.l~g weight loss, may be reached at a mine face with 314,000 L of dilution air, at the 5th min, during which less than 1 kg of brattice undergoes combustion. Fiberglass, cotton, and jute brattices, pine wood dust, and coal dust showed small concentrations of carbon monoxide evolving during early stages of combustion. Hydrogen cyanide gas evolved from the PVC-derived, nylon-reinforced brattice; at a later stage of combustion, large concentrations pf carbon monoxide and dense smoke evolved from all PVC-derived brattices. Experiments to characterize smoke particles showed that marked differences exist in particle diameter-concentrations among the materials.

Jan 1, 1986

While coal occurs beneath about 18 percent of Utah, only 4 percent of the state has minable reserves. Utah's coal fields are mostly bituminous. Current coal production in Utah is largely by underground mining, making Utah unique among the coal-producing states. Most coal seams are more than 8 feet thick. Utah's coal resources are about 6.3 billion tons, 1.3 percent of the national reserve. Most of Utah's coal resources are held by the Federal Government and Indian tribes and are mined under lease. The climate of the Utah coal region is characterized by hot, dry summers and cold, relatively moist winters. Normal precipition varies from 6 inches in the lower valleys to more than 40 inches on some high plateaus. The growing season ranges from 5 months in some valleys to less than 3 months in mountainous regions. These extreme climatic conditions make reclamation difficult. Utah gained primacy when its regulatory program was conditionally approved January 21, 1981. Full program approval was obtained March 7, 1983. The Abandoned Mine Land Program was approved June 3,1983. A Federal Lands Cooperative Agreement was signed in March 1987; Utah performs all enforcement activities and some permitting activities on federal lands.

Jan 1, 1992

By F. D. DeVaney

Manganese-bearing deposits of the Leadville, Colo. district are of two distinct types. Mangano siderite, a combined or intimately mixed ferrous and manganous carbonate, occurs in unaltered zones as the predominant mineral. From 50 feet below the surface to as deep as 800 feet, psilomelane and wad, both black manganese oxide minerals, are found in intimate contact with hematite and limonite. A typical analysis of the black oxide ore shows 20.08 percent Fe, 19.64 percent Mn, 15.91 percent insoluble, 14.91 percent moisture, 0.94 percent Zn, and 2.13 percent Pb. A considerable tonnage of the oxide ore has been mined for production of spiegeleisen and for other purposes.

Jan 1, 1940

By A. E. Raddatz

The Federal Bureau of Mines, as part of its goal to minimize undesirable environmental impacts associated with mineral processing, has investigated a soda-smelting technique for processing ilmenite into pig iron and a titanium slag that is suitable for a feed to a sulfate-process titania pigment plant. By this procedure, the generation of ferrous sulfate waste and its associated disposal problem is obviated. Molten titania slag was quenched, water leached, and filtered to yield a sodium titanate intermediate product containing about 70 wt-pct Ti02, 1 wt-pct Fe, and 20 wt-pct Na20. This intermediate product, high-soda titanate (HST), was mixed with H2S04, calcined, quenched, and water leached to produce a low-soda titanate (LST) product that contained only 2 wt-pct Na20. Both the HST and LST were evaluated as feed materials for preparing titania by the sulfate process. About 95 pct of the Ti02 was extracted from HST and LST by digestion in concentrated or 50-wt-pct-H2S204 solutions. About 95 pct of the solubilized Ti02 was subsequently recovered from the titanyl sulfate solutions by hydrolysis. Barren solutions from hydrolysis, containing about 26-wt-pct H2S04, were upgraded by vacuum-thermal evaporation or electrodialysis. The regenerated acid solutions were used to digest additional HST and LST.

Jan 1, 1979

By M. J. Ferrante

Low-temperature heat capacities and high-temperature enthalpies were determined calorimetrically for Na2Cr04, A reversible transition was found at 700° K with an isothermal heat of transition of 2,263 cal/mole. High-temperature X-ray diffraction analysis showed that the transition was a crystal change from the low-temperature orthorhombic form to the high-temperature hexagonal form. At 795° K the hexagonal form had the parameters a, = 5.691 and co = 7.478 A. Powder diffraction data for the high-temperature form are given and possible structures discussed. The melting point was determined to be 1,065° K with a heat of fusion of 5,810 cal/mole. Enthalpy and entropy increments from this investigation were combined with other data from the literature to calculate enthalpies of formation, free energies of formation, and equilibrium constants of formation from 298° to 1,400° K. Equations that represent enthalpies above 298° K are given.

Jan 1, 1972

By Lee J. Raabe

A specialized loading system for tensile and fatigue testing of wire rope was constructed and installed in the U.S. Bureau of Mine Wire Rope Test Facility in Bruceton, Pennsylvania. The computer-controlled closed-loop servo-hydraulic test system which can apply up to 800,000 pounds of force on the rope while stretching it up to 30 inches will be used in the development and verification of hoist rope retirement criteria for ropes in the 1 to 2 ½ in. diameter range. Characteristics and capabilities of the system are discussed.

Jan 1, 1984

By Raymond B. Ladoo

"The name bentonite has been applied to a group or series of clay-like materials characterized by an alkaline oxide and alkaline earth content of 5 to 10 per cent, fine grain Giza, high absorptive powers, and usually very strong colloidal properties.Bentonite probably represents no mineral of fixed composition, and its physical properties vary considerably. The type material from Wyoming is light yellow or greenish yellow in color, but from other localities it may be cream colored, white, gray, pink, dark brown or even black. It is exceedingly fine grained, very plastic and highly absorbent. The appearance may be dull or powdeay, but a freshly cut surface usually has a waxy luster. Some varieties have the appearance of wax and may be cut into very thin, translucent shavings. The fracture of the type material is roughly conchoidal, that of other varieties is platey and shale-like, while still others have no typical fracture. Bentonite is highly absorbent; .hen wetted it will absorb more than three times its weight or seven times its volume of water. Some varieties when wetted with water expand to more than six times (some experimenters report eight times) their original volume. The wetted material is exceedingly smooth and soft and feels like soft soap. Unlike most clays, bentonite is easily fusible at a comparatively low temperature.Under a high-power microscope bentonite seems to consist of extremely small, more or less rounded, grains of uniform size, but the texture of most varieties is so fine that individual grains can not be distinguished.Some varieties when finely ground and thoroughly agitated with water will stay in suspension indefinitely, forming a translucent gelatinous mass. The addition of small amounts of acids or sodium chloride seems to have little or no tendency to raid coagulation or settling. Other varieties of similar analysis and appearance go into suspension more easily, but settle out again in a comparatively short time. It has been suggested that the material which stays in suspension indefinitely is a true colloid of the emulsion or lyophilic type."

Oct 1, 1921

By R. L. Grant

Study of the ignition of firedamp by explosives and the phenomena that underlie it is one of the long-term investigations of the Bureau of Mines. This report is the third in e series by the Explosives Branch summarizing the progress made at Bruceton in this study. The first paper described preliminary work on small, carefully controlled cannon shots the second discussed the results of suspended shots.5/ In this paper, experiments are described and interpreted that extend and support the concept of ignition presented previously. ACKNOWLEDGMENT The authors wish to thank Bernard Lewis, former chief, Explosives and Physical Sciences Division, and Guenther von Elbe, former chief, Physical Sciences Branch, Explosives and Physical Sciences Division, for their guidance and constructive interest.

Jan 1, 1954

By Nadia C. Miller

In situ metals research to characterize the hydrology of a fractured crystalline rock mass in under-ground mine stopes is discussed. The objective of this study was to find the potential direction, velocity, and concentrations of a lixiviant plume, should leaching solvents (lixiviants) escape from a test stope. The study was conducted by the U.S. Bureau of Mines at the Colorado School of Mines Experimental Mine in Idaho Springs, CO. Since this was a method evaluation site, the lixiviant was simulated using water and acceptable tracers. The site is located in moderately fractured Precambrian migmatite-biotite gneisses of the Idaho Springs Formation. The data required for the characterization were obtained from geologic maps and reports, core logs, and air and water permeability tests. The acquired data were analyzed and applied to a computer model that calculated' the characteristics of a lixiviant plume originating at the stope. A sensitivity analysis showed that dispersivity, ground water velocity, fracture porosity, and fracture spacing had notable effects on the concentration of the plume. Assuming a saturated rock mass, the lixiviant plume would disperse to undetectable levels in a very short time because of a high fracture density at the mine site.

Jan 1, 2010

By P. W. Jeran, S. J. Pepperney, M. C. Irani, F. F. Kopsch

The Bureau of Mines has designed and put into operation a fail-safe control system for use in underground coal mines equipped with methane drainage pipelines. This control system can detect certain unsafe conditions and respond by automatically shutting off the flow of methane from the degasification borehole to the drainage pipeline. Methane flow is shut off when the methane content in the return airways reaches a predetermined level (typically 1.5 pct), when the methane drainage pipeline is ruptured by roof fall, or when there is an electric power failure. The fail-safe control system was designed using commercially available components and a methane analyzer system previously developed by the Bureau. The fail-safe system consists of a unit that combines a shutoff valve and pneumatic valve actuator, and electronic and mechanical equipment designed to detect hazards and effect shutdown. The fail-safe control system was designed to meet regulatory requirements issued by the Mine Safety and Health Administration (MSHA), U.S. Department of Labor, and State regulatory bodies for the safe operation of underground methane pipelines used for mine degasification. MSHA has inspected and tested this system and permitted its use in two mines. The Bureau installed the fail-safe system in two working coal mines, where successful performance has been demonstrated.

Jan 1, 1980

In the last few decades, a considerable amount of effort was directed at accurately determining the coal pillar strength to use for safely designing coal mines. The outcome of this early work was the well known Obert-Duvall, Holland-Gaddy, Bieniawski, and Salamon-Munro equations for coal pillar strength. All of these equations were developed for, and were calibrated with, pillars in a large room-and-pillar area such that the loading could be determined using the "tributary-area" theory. In order to account for the abutment loads associated with full-extraction mining, the empirical methods have typically adopted a simple conceptualization of the abutment load through use of an "abutment angle." Short of a complete numerical or analytical analysis of the coal seam and surrounding strata, very little work has been Fretted toward refining the empirical analysis of pillar loading. It appears that the vast majority of the research has been directed at determining the pillar strength, the numerator of the safety factor equation, when the denominator of the safety factor equation, the pillar loading, plays an equally important role in pillar design. This paper will address the deficit of pillar loading research by exploring the accuracy of the empirical abutment load calculations using insight provided by an elastic overburden model, a laminated overburden model and field observations. Ultimately, it is determined that a constant abutment angle probably over-predicts the abutment load as the mining depth increases.

By G. Richards Gwinn

In modern warfare, mica is truly indispensable. Coordination of combatant units necessitates maintenance of intricate communications equipment, in the construction of which high-grade sheet mica is essential. Scrap, ground, and the poorer qualities of block mica, which are less essential to the military program, are not considered in this paper. Furthermore, as the paper is designed primarily to assist mica miners, mica derivatives, Such as splittings and films, also are excluded from discussion. The paper therefore relates solely to block mica of strategic quality. Understanding of t e many factor involved in marketing mica is definitely advantageous to mica, miners. The nature and detrimental effects

Jan 1, 1943

By Hugo E. Camargo

In an effort to reduce Noise Induced Hearing Loss (NIHL) in the mining industry, the National Institute for Occupational Safety and Health (NIOSH) is conducting research to develop noise controls for mining equipment whose operators exceed the Permissible Exposure Level (PEL). The process involves three steps: 1) Noise source identification (NSI), 2) development of noise controls, and 3) evaluation of the developed noise controls. For the first and third steps, microphone phased array measurements are typically conducted and data are processed using the conventional beamforming (CB) algorithm. However, due to the size and complexity of the machines, this task is not straight forward. Furthermore, because of the low frequency range of interest, i.e., 200 Hz to 1000 Hz, results obtained using CB may show poor resolution issues which result in inaccuracy in the noise source location. To overcome this resolution issue, two alternative approaches are explored in this paper, namely the CLEAN-SC algorithm and a variarion of an adaptive beamforming algorithm known as Robust Capon Beamformer (RCB). These algorithms were used along with the CB algorithm to process data collected from a horizontal Vibrating Screen (VS) machine used in coal preparation plants. Results with the array in the overhead position showed that despite the use of a large array, i.e., 3.5-meter diameter, the acoustic maps obtained using CB showed "hot spots" that covered various components, i.e., the screen deck, the side walls, the I-beam, the eccentric mechanisms, and the electric motor. Thus, it was not possible to identify which component was the dominant contributor to the sound radiated by the machine. The acoustic maps obtained using the RCB algorithm showed smaller "hot" spots that in general covered only one or two components. Nevertheless, the most dramatic reduction in "hot" spot size was obtained using the CLEAN-SC algorithm. This algorithm yielded acoustic maps with small and well localized "hot" spots that pinpointed dominant noise sources. However, because the CLEAN-SC algorithm yields small and localized "hot" spots, extra care needs to be used when aligning the acoustic maps with the actual pictures of the machine. In conclusion, use of the RCB and the CLEAN-SC algorithms in the low frequency range of interest helped pinpoint dominant noise sources which otherwise would be very hard to identify.

Jan 1, 2009