Search Documents

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

B 6 Listing The following is a listing of the Mine Evacuation Simulation Program

Jan 1, 1976

By Robert E. Hershey

1. The investigation shows that the Sewanee coal bed is the most important bed in Grundy County arid is the only bed that has had any sustained production. There is no production, at the present time, from any of the other coal beds in the county. The Richland (Lower Sewanee or Coke Oven) coal bed has been prospected but has never been developed extensively. The Angel coal bed has been worked to a very small extent near Beersheba Springs, Tenn., for local consumption. The Battle Creek coal bed has been worked sporadically near Monteagle, Tenn. 2. Known measured and indicated reserves in the Sewaneee coal bed, based on a minimum thickness of 14 inches and on 1,800 short tons per acre-foot of coal in place, are estimated to be 15 millon short tons as of January 1, 1953. Of this total, 10 million tons represents coal 28 inches and more thick. Areas in the bed were omitted from the estimate where available data relative to the bed characteristics are too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1955

By John W. Kopp

Stemming is used in blasting operations to help contain explosive gases as long as possible. Stemming can reduce airblast, improve fragmentation, and reduce the chances of hot explosive gases igniting methane and dust explosions in underground mines. Stemming is required in underground coal mines but is generally not used in underground metal and nonmetal mines. Some underground metal and nonmetal mines are classified as gassy and can require special blasting procedures such as the use of stemming to minsure the safety of miners. The types and amounts of stemming material that are desirable in underground metal and nonmetal mine blasting to ensure good or improved fragmentation while containing the hot gases are largely unknown. This Bureau of Mines research examined the effectiveness of differing lengths of stemming by measuring stemming ejection times as related to burden movement. With properly stemmed blasts, stemming is contained until some burden movement has occurred. Test blasts at two surface limestone quarries were evaluated using high-speed photography. For the conditions of these tests, a stemming length of at least 26 charge diameters was found to prevent premature stemming ejection. In tests with stemming lengths of 16 charge diameters, the stemming was effective but there was early venting of hot gases through fractures in the rock. Further testing with other rock types, hole diameters, explosive types, and stemming materials as they affect incendivity is recommended.

Jan 1, 1987

Predict the spontaneous combustion potential of a mining operation using an expert system computer program.

Jan 1, 1994

By Laxman S. Sundae

Laboratory tests were conducted at the U.S. Bureau of Mines to determine the effects of roof-bolt drilling parameters on penetration rate in sandstone using tungsten carbide alloy (WC-Co) and polycrystalline diamond compact (PDC) drill bits. During the tests, water pressure of 552 kPa was found to be adequate for removing the cuttings from the tops of drill holes. Test results show that for both types of bits, penetration rate increased when thrust was raised from 227 to 1,588 kg. When water pressure rose from 554± 120 to 1,344±350 kPa, the effect on penetration rate was not significantly different. Conventional WC-Co bits became dull when one or two holes were drilled, after which the penetration rate dropped dramatically. Microscopic examination shows that the cutting edges of PDC bits also become somewhat dull, but at a much lesser rate than WC-Co tips. Microscopic examination also reveals that the wear mechanism of WC-Co and PDC bits is quite different, which may explain the longer life of the PDC bits.

Jan 1, 2010

By M. J. Lempel

A theoretical study of the heat-transfer characteristics of a dilute gas-solids mixture in an externally heated tube is reported. Detailed equations are developed describing the system, and a numerical method is presented to solve the equations using a digital computer. The methods are applied to a system containing fine coal particles entrained in hydrogen, flowing through a hot tube. Heat-transfer coefficients and several other physical constants are evaluated in detail.

Jan 1, 1967

By Peter F. Steidl

As part of the Bureau of Mines methane control program, the Upper Free-port coalbed was studied in Fayette County, Pa., where this coalbed lies about 650 feet below the Pittsburgh coalbed and contains the largest remaining reserves of any coalbed in the county. Coal and overburden isopachs, structure and joint pattern maps, and a fence diagram were prepared using data from gas and oil exploration logs and coal outcrops. These maps will aid in deter-mining the need and/or feasibility of degasifying the Upper Freeport coalbed in the study area. Much of the coalbed in this area is under 600 to 1,400 feet of overburden. By correlation with data from the Pittsburgh coalbed, the gas content at depths of this order is estimated to be between 140 to 300 cf/ ton of coal, for a total of 190 to 400 billion cubic feet of methane in this coalbed in Fayette County.

Jan 1, 1977

By J. G. Croeni

The high thermal-neutron cross section of gadolinium and the good mechanical and corrosion properties of titanium suggest that alloys of these two metals might be useful as control rod material. To aid in establishing the feasibility of this combination, the Federal Bureau of Mines investigated the titanium-gadolinium system. The results indicate that the system is composed of a single eutectic reaction and a peritectoid reaction involving the alpha-beta transformation of titanium. The eutectic isotherm extends from 1 to 99 pct, gadolinium at 1,240° C. The established eutectic composition is about 95 pct, gadolinium. The peritectoid reaction occurs at 885° C. and extends almost over the entire composition range. Hardness increases slightly with additions of gadolinium, and little change is obtained by heat treatment. Alloys containing less than 10 pct. gadolinium are amenable to extensive cold-working, but alloys having higher percentage of gadolinium content are only moderately cold-workable. All alloys can be hot-worked in iron sheathing at 750° C. Observation indicates that all compositions possess good machinability. Corrosion resistance to water at room temperature is apparently poor, especially in the gadolinium-rich alloys. INTRODUCTION A combination of the good mechanical and corrosion properties of titanium and the variety of thermal-neutron cross sections characteristic of the rare-earth metals suggests that alloys of these metals may be used for control rod materials. For this reason the Bureau of Mines proposed a study of the titanium-gadolinium alloy system, and the Atomic Energy Commission sponsored the investigation.

Jan 1, 1961

By W. B. Berwald

[Accurate ~cusirc::ie t of euusu.rface r,resw rus £Uld tee:: ?er:~t:,res in producin+ oil and as wells is one of tine ast iy,ulortant steps ever t,.s:en to place the rprwctice of retroleum ,-iroduction on an exact scientific basis. i'reerures and teial.or-tures in a -petrolcuia r4:, rvoir. have a rn..r..ed influence over the o:wvement of oil and ~c s both within the. reservoir and t~:rou,=Ii the various-size "flow otrin;;u" of proLucin,; wells to tine surface. Knovrled: ?c of theso fc,.ctgrs form a Laois for cny attei:ant to [.,-~ly eciantific j:cthods to the solution or analysio of mc.nj proble;ae encountered in the production of oil and 1c_c, Without a.ccur:tc mcaaurx,ients of reosures r:.nd tcn::paratuxes within the rocervoit and -well 'flo-,r strinL:s" tae aI,licution of w.ny proved enbinecrin and scientific princiy-,loo is on %,]

Jan 1, 1935

By Jr. Gabler

Because of concern over the availability and reliability of an uninterrupted supply of manganese and other materials, the U.S. Congress requested that the U.S. Bureau of Mines (USBM) study the /low of strategic and critical materials in the economy to delineate and quantify the production areas where metal values are lost. As a result, the USBM developed a generic computerized commodity flow model that is readily amenable to updating. The original model developed for cobalt, with slight modifications, was used to track the flow of manganese. This report follows the flow of manganese through its metallurgical and chemical applications and highlights areas where significant losses occur owing to downgrading, export, or disposal. The study indicates that materials containing 695,000 short tons (st) of manganese were consumed domestically in 1990. Scrap recovery specifically for manganese recycling was insignificant. However, considerable manganese was recycled through processing operations as a minor component of ferrous and nonferrous scrap and steel slag. The major loss category is manganese lost in steel processing, 323,156 st or 46 pet of the 1990 apparent consumption. Most of this loss reports to steelmaking slags. Recovery from slags is technically feasible, but is not economically feasible.

Jan 1, 1995

By William C. McBee

Prompted by forecasts of a sulfur oversupply, the Bureau of Mines, U.S. Department of the Interior, is conducting research on potentially large-scale uses of this commodity to extend or replace such construction materials as asphalt, cement, and mineral aggregates. Through these efforts, paving materials have been developed in which sulfur replaces up to 50 pct of the asphalt normally present and which can be prepared and placed with existing mixing and paving equipment. Laboratory properties and design methods for this direct mixing process are described along with properties obtained on small-and large-scale field demonstration projects. These properties are compared with those obtained from control materials prepared without sulfur additions. Monitoring for toxic gases during laboratory and commercial mixing and paving operations is discussed also.

Jan 1, 1978

By W. H. Strickland

Ultrasonic ranging sensors are inexpensive, have no moving parts, have no lenses to clean, are normally small and unobtrusive, and can measure distances through moderate amounts of dust, smoke, and humidity, so they are well suited to underground mines. In the work reported here, conducted by the U.S. Bureau of Mines, researchers tested ultrasonic ranging sensors for their ability to define rib line features for computer-aided navigation of underground mine mobile equipment. The investigation began with laboratory tests of field of view, angle of incidence, intersensor variation, and ranging accuracy of the individual rangers in a ring array produced by Denning Robotics of Wilmington, MA, The results showed that the sensors have good accuracy and low variability. Additional experiments at AMAX'S Henderson Mine showed the sensors could accurately and reliably measure the distance to mine features, including convex and concave corners and rib intersections. The results showed that when used properly, the ranger data are accurate enough for reliable mine vehicle navigation. When used incorrectly, ultrasonic rangers do not provide the anticipated data. Therefore, this report explains the principles of ultrasonic range measurement, describes the ranger's strengths and weaknesses, and explains proper ranger use and data analysis.

Jan 1, 2010

By Lester J. Crow

A preliminary survey was performed to investigate the impregnation of relatively weak, porous volcanic tuff and a relatively strong, dense sandstone with five different monomers. Increases in compressive strengths by factors of 2 to 5, and elastic moduli by factors of 2 to 3.5, are reported for natural rocks (tuff., sandstone, dacite), which were impregnated with five monomers (methyl methacrylate; chlorostyrene; 40 percent TMPTMA-60 percent styrene; 40 percent TMPTMA-60 percent chlorostyrene; 60 percent polyester-40 percent styrene); polymerization took place after monomers were forced into the rock. Impregnation was performed (1) by pressurizing rock specimens from one end, or (2) by a vacuum-soak operation. Polymerization was accomplished by either radiation or chemical initiation techniques. Strength improvement is dependent on (1) the type of monomer used, (2) the amount of polymer incorporated into the rock, and (3) the degree of water saturation of the rock. Water saturation strongly reduced the effectiveness of the method for the polymer systems tested. The more viscous monomers (for example, 60 percent polyester-40 percent styrene) were more effective in displacing the water from the rock, and compressive strengths of wet rock were doubled with these systems. Water saturations ranging from 25 to 100 percent of maximum saturation gave essentially identical results. Further tests on other types of mine rock; including shale and coal, are planned. Water-compatible polymer systems should be developed, or present systems should be suitably modified. For application to tunnel stabilization, design studies evaluating the improvement in rock strength and its influence on the support system are also recommended.

Jan 1, 1971

By W. W. Adams

Lower accident rates were the outstanding feature. of the second annual sand and gravel safety competition conducted in 1930 by the United States Bureau of Mines in cooperation with the National Sand and Gravel Association. Both the frequency and, severity rates for accidents were greatly reduced as compared with those shown by the first year's contest, that for 1929. Three times as many plants were enrolled, and the number of man-hours of work represented wad more than doubled. Seventy-six sand-and-gravel plants, situated in 20 States, participated in the competition, as compared with 26 plants, located in 13 States, in the year before. The number of man-hours of employment, which indicated the amount of exposure to occupational hazards, was 4,915,592 an increase of more than 100 per cent over, the previous year's total of 2.259,572 hours. The frequents of accidents declined from 74.4 per million hours for all plants enrolled in the first year's contest to 42.7 per million man-hours for all plants enrolled in 1930. The accident-severity rate was reduced from 9.7 days of disability per thousand man-hours of exposure in 1929 to 5.9 days of disability per thousand man-hours of exposure in 1930.

Jan 1, 1931

By G. M. Molinda, J. P. Ulery

Since 1970, abnormally high methane emissions have been observed in eastern sections of the Federal No. 2 Mine operating in the Pittsburgh Coalbed in northern West Virginia. The nature and volume of these emissions indicate a source other than the coalbed. An investigation was undertaken to delineate probable methane sources. Gas well information and stratigraphic correlation of corehole data indicates that a sandstone directly above the main coalbed is an additional source of methane emissions. The sandstone body appears to be an ancient stream channel, infilled with fine-grained sand and organic matter. Coalification of the organic matter produced methane as a byproduct. Additional methane presumably migrated into the sandstone unit from the subjacent coalbeds. The methane became trapped in the porous clasticunit by the surrounding impermeable strata. Mine development near this unit creates a significant pressure gradient, triggering abnormal methane emissions into the mine along naturally occurring fractures. Pre-development methane drainage of the sandstone could be accomplished by completing vertical boreholes along its trend.

Jan 1, 1984

By E. Morrice

As part of its efforts to maximize process efficiency and decrease energy requirements in mineral processes, the Federal Bureau of Mines has investigated methods for beneficiating bastnäsite ores from Mountain Pass, Calif. The results of a bench-scale study on the flotation of bastnäsite ore are presented. Flotation at a pulp temperature of 40° to 45°C yielded a cleaner concentrate containing 58.7 pct RE203 at a rare-earth recovery of 67 pct. These results are comparable to those reported for the commercial beneficiation method in which the pulp is heated to boiling before flotation. An attempt was also made to recover a barite flotation concentrate from the bastnäsite rougher tailing. Concentrates containing only 70 pct barite were obtained.

Jan 1, 1982

By Ned Baker

Details are given of a fuel-induction system for a hydrogen, fueled engine. The induction system was designed to preclude backfire otherwise common in hydrogen fueled engines. System features and test data are presented and discussed in the context of the requirements peculiar to use in an underground mine environment. The fuel induction-system when tested in conjunction with a modified Caterpillar 3304 engine provided backfire free engine operation and satisfactory engine performance.

Jan 1, 1982

By A. Y. Lee

Prior work at the Bureau of Mines resulted in the successful development of a bench-scale, combination electrorefining-electrowinning method for recycling the lead from scrap batteries using waste fluosilicic acid (H2SiF6) as electrolyte. This paper describes larger scale experiments. Anodes cast from scrap battery lead were electrorefined in a 20-L multielectrode cell for 3 to 7 days. The anodes, containing 2 to 2.5 pct antimony, were ideal for obtaining firm and adherent slime blankets. Cathode deposits, assaying 99.99 pct Pb, were obtained, with current efficiencies near 99 pct. Sludge leaching was done in 100-L tanks followed by filtering in 61 cm square vacuum pan filtersu Lead of greater than 99.99-pct purity was recovered from the filtrate by electrowinning in a 20-L multielectrode cell using insoluble Pb02-Ti (lead dioxide-coated titanium) anodes and pure lead cathodes. The fluo-silicic acid electrolyte depleted in lead was repeatedly recycled to leach more sludge, and there was no problem with impurity buildup. The amount of Pb02 formed on the anodes during electrowinning was less than 1 pct of the total lead deposited on the cathodes, as long as the phosphorus concentration in the electrolyte was greater than 1.3 giL. Emissions of lead in air were less than 10 ~g/m3, well below the proposed OSHA limit of 50 ~g/m3.

Jan 1, 1984

By William R. Wayment

The objective of this investigation was to obtain data on friction-head losses of sand slurries during their transport in pipelines. The data ultimately will be used in designing hydraulic transport systems. Information that was incidental to the primary objective was gathered on degradation, changed percolation characteristics, and critical velocities of the slurries~ Tests were made in a closed-circuit pilot plant, with one type of tailing, through horizontal 2-, 3-, and 4-inch-pipe test sections at various pulp densities and flow velocities. Tests were made in a closed-circuit pilot plant, with one type of tailing, through horizontal 2-, 3-, and 4-inch-pipe test sections at various pulp densities and flow velocities. Approximately 2,000 tests were run in the pilot plant. The ranges of flow velocities used in the experiment were 2.8 to 19 f.p.s. in the 2-inch line, 4 to 14.5 f.p.s. in the 3-inch line, and 4 to 11 f.p.s. in the 4-inch line. Velocities were varied in increments of 0.5 f.p.s. through the entire velocity range in each pipe size. Densities were varied in 3-percent increments from 40 to 70 percent solids by weight except for one series of tests in the 2-inch line; in this series, densities were varied in 5-percent increments from 5 to 65 percent solids by weight.

Jan 1, 1962

By L. A. Haas

In this Bureau of Mines investigation, conditions were determined to form an iron sulfide adherent coating with a metallic golden luster on steel upon anaerobic heat treatment with sulfur. The sulfide formation rate was determined in the temperature range of 105° to 500° C with reaction times up to 68 hours. The optimum temperature and time to form an adhering decorative coating on mild steel was in the range of 105° C for about 70 hours to 285° C for 1 hour. The golden coating consisted of an inner layer of pyrrhotite and an outer layer of pyrite. At temperatures higher than about 300° C, the outer layer thickness decreased owing to the decomposition of pyrite to pyrrhotite.. Small quantities (<0.5 wt-pct) of petroleum oil accelerated the sulfide growth rate. The sulfide coating decreased the corrosion rate of steel in a neutral aqueous medium by a factor of two. The dissolution of pyrite in water was dependent on particle size and surface area with the flat pyrite coatings exhibiting the lowest dissolution rate.

Jan 1, 1974