Search Documents

By Richard W. Watson

Card-gap and projectile impact sensitivity data are presented for a wide variety of explosive compositions tested at the Bureau of Mines in more or less standard test geometries. The results of both tests are in good agreement in that they provide the same sensitivity ordering for different subclasses of explosives. Least sensitive were homogeneous liquids that did not exhibit a tendency to undergo low-velocity detonation, ammonium nitrate-fuel oil, and most cast military explosives. Of intermediate sensitivity were pressed and powdered military explosives, cast pentolite, permissible and non- permissible water-based explosives, and one commercial two-component explosive. The most sensitive were permissible and nonpermissible dynamites and explosives susceptible to low-velocity detonation.

Jan 1, 1973

By R. E. Heithecker, Van A. Mills

"Crude oils are capable of dissolving quantities of gas under pressure. This fact has been known for some time, but questions have arisen as to the effects of gas in solution upon the characteristics of the oil. Previous investigations4 show that gas in solution in an oil affects the viscosity and surface tension of the oil, but the effects on the volume and A. P. I. gravity of the oil have not been known. The results given in this report show that there is a decided change both in volume and in the A. P. I. gravity of the oil due to the solution of the gas in the oil under pressure. As gas is dissolved, the volume of the oil and the A. P. I. gravity increase. The converse of this phenomenon is also true: if the gas is released from a saturated oil, there is a shrinkage in volume and a decrease in A.P.I. gravity due to the release of gas from solution. However, various oils show marked tendencies to retain a portion of the dissolved gas upon releasing the pressure to that of the atmosphere. This retained gas has an appreciable effect on the volume and A. P. I. gravity of the oil because the oil does not resume its initial volume or gravity while it retains dissolved gas. In a sense the oil has been ""freshened"" and will not return to its original or weathered volume until it loses some of the lighter fractions. Wiggins5 has shown that a fresh oil decreases both in volume and in gravity because of the weathering of the lighter fractions while the oil is standing in storage tanks.This paper includes data attained during the determination of volume and gravity correction factors to be applied in the oil recovery investigations of the Bureau of Mines. Three oils having a wide range in gravity were used in determining the correction factors. These oils were from the Bartlesville-Dewey field, Oklahoma, the Seminole field, Oklahoma, and the Inglewood field, California. The same gas that was used in the oil recovery experiments was used throughout this investigation. Determinations were made of the volume and A.P.I. gravity increases resulting from the gas going into solution at 200, 400, 600, 800, and 1,000 pounds pressure; also the increases in the volume and gravity of the oil due to retained gas were determined after the dissolved gas was liberated from solution by releasing the pressure to that of the atmosphere.Samples of residual and liberated gas were taken throughout the investigation in order to study the selective absorption and selective retention by the oil of the various constituents of the gas. The analyses of these gas samples showed that there was selective absorption and selective retention of the constituents of the gas. The tests on Inglewood crude gave the most pronounced example of selective absorption and selective retention of the gas.All of the tests were conducted at a constant temperature of 709F."

Oct 1, 1928

By D. Montagna

Large quantities of zinc-base die-cast scrap containing 3 to 4 percent aluminum are presently refined by mixing with other secondary zinc products such as galvanizer dross and distilling in a retort. The Bureau of Mines investigated alternate aluminum removal processes utilizing low-cost fluxes. Basing the investigation on the metallurgical principle that a reactive impurity can be removed from a less reactive matrix metal by melting under a flux consisting of a salt or oxide of a metal less reactive than the impurity, three separate flux mixtures were studied. In the first flux system, [FeCl3] + NaCI (the active component is underlined), part of the aluminum is' eliminated by the formation of volatile aluminum chloride and the rest by the creation of a high melting point iron-aluminum intermetallic compound that can be separated from the remaining molten zinc by filtration. Aluminum removal in the second system, [Fe203] + CaClz + NaCI, is effected by the formation of the iron-aluminum compound and possibly aluminum oxide. The third system, spent sal skimmings--essentially a mixture of [ZnCl2], NH4Cl, and ZnO, depends solely on aluminum chloride formation. Of the three flux systems investigated, the best results obtained were with system 3. Aluminum was reduced in the molten die-cast alloy from 4.10 percent to 0.01 percent when depleted sal skimmings were used.

Jan 1, 1969

By A. Mayton, A. Brien, W. Porter, O&apos

In 2004, management at Unimin's Gleason, TN operation began implementing ergonomic interventions specifically targeted to reduce risk of musculoskeletal injuries (MSIs). Together with corporate and site management, Unimin identified work site hazards and began to modify work practices/equipment. Some interventions were relatively simple and were implemented immediately. Others, like improvements to a mobile shredder, were more complex but were eventually resolved through a participatory approach with employees, management, manufacturers and NIOSH. This paper discusses ergonomic interventions that were successfully implemented using a bottom-up approach to reducing the risk of injury.

By Walter Kawa

Bureau of Mines research on the hydrogenation of coal has been concerned with developing processes that could be used to supplement the Nation's petroleum and natural gas resources. Motor fuel was produced in a subsidized coal hydrogenation industry in Europe prior to 1945, but the process used is still not economical and other methods of producing liquid and gaseous fuels from coal are being investigated. As an aid to the planning of coal hydrogenation research, a literature survey was made of processes or methods of hydrogenating coal that differ from the subsidized or conventional process. This report contains a bibliography of unconventional methods of hydrogenating coal and a brief discussion of the economics of the conventional method. A general discussion of unconventional methods is included, and the advantages and disadvantages are pointed out where possible. The survey supplements a previous Bureau of Mines survey3 and a comprehensive review published in 1930.4

Jan 1, 1964

By R. D. Rosenkranz

The Bureau of Mines has investigated the availability of copper from 272 deposits in market economy countries. The deposits studied have demonstrated resources totaling 413 million metric tons of contained copper and account for more than 90 pct of the reserve base for market economy countries. Using data gathered as part of its Minerals Availability Program, the Bureau performed geologic, engineering, and economic evaluations in order to determine the copper production potential of each deposit. At the 1981 copper market price of $0.85/lb, the deposits studied could economically produce an estimated 88 million metric tons of copper (allowing for profit computed at a 15-pct rate of return), primarily from mines operating at the time of the study (1981). At this price, producing mines in market economy countries could economically produce only 2.1 million metric tons of refined copper per year. However, actual 1981 production was 6.2 million metric tons, indicating that many mines continued to operate even though they were unable to cover all production costs. For U.S. producing mines, the estimated average cost of production per pound (including profit at a 15-pct rate of return) was $0.15 higher than the average cost in other market economy countries.

Jan 1, 1983

By D. E. Wolfson

As part of its overall program of coal carbonization, the Bureau of Mines is studying the coking properties of coals that may be used for metallurgical purposes. The objectives of this study were given in detail in a previous report.2/ The suitability of coal for metallurgical use depends primarily on (1) chemical composition, (2) preparation characteristics, and (3) carbonization behavior. The first two factors, as well as the available reserves, are considered in selecting coals for carbonization tests. According to the estimate of reserves by Dowd,3/ the recoverable coal in Raleigh County in beds 28 inches or more thick, in thousand tons, is: [ ]

Jan 1, 1957

"Contained in this chapter is a listing of the publications and reference books which have come about as a result of respirable dust research performed by faculty, staff and graduate students in the Generic Mineral Technology Center for Respirable Dust at The Pennsylvania State University, West Virginia University, University of Minnesota, Massachusetts Institute of Technology, and Michigan Technological University. These publications have appeared in scientific journals, proceedings of the national and international symposiums, and professional meetings. Complete citations of the publications can be found in Volumes 3 through 6 and Volume 8 of this series. The agenda of the last annual GMTC seminar, held at West Virginia University on February 1 - 2, 1988, follows. The project presentations are organized under the five research areas. All projects currently active were presented to the Advisory Committee. New project submissions were not. The authors were allotted thirteen (13) minutes for their presentations; the remainder of the twenty (20) minutes allotted for each project was used for introductions, transitions, and questioning by the Advisory Committee. Each author used a standard format for presentation of his/her materials for review; handout materials were distributed to the Advisory Committee for reference. Opening remarks were made by Dr. Richard Bajura of West Virginia University and Dean Robert L. Frantz and Dr. Raja V. Ramani of The Pennsylvania State University.The Generic Mineral Technology Center for Respirable Dust is funded by the U.S. Bureau of Mines through the Mining and Mineral Resources Research Institute Program. The opinions and conclusions expressed in these papers are those of the authors alone and do not represent the opinions of the Generic Mineral Technology"

Aug 31, 1989

By Kenneth M. Smith

The kaolin deposits of Aiken County, South Carolina (fig. 1), have been worked continuously since 1852. It has been long known that the deposits contain a high percentage of' alumina and that large reserves exist. These facts led to the early selection of' this area for examination in the search by the Bureau of Mines for high-alumina clays. An exploratory program was started by the Bureau, and drilling was carried on from. June 27, 1942, to October 31, 1942. The kaolin-bearing district occupies an area approximately 25 miles long and 11 miles wide, running northeast, with its center at Aiken, S. C. (fig. 1). Within this district, a triangular area bounded by Horse Creek, Silver Bluff Road, and Hamburg Road was roughly prospected by boring 43 machine and 12 hand holes. As a result of the data obtained, a final smaller area was chosen for more systematic prospecting. This area is bounded by Pine Log, Tewkesbury, Silver Bluff, and Craig Sawmill Roads and covers about 4,000 acres. Mineral exploration agreements covering 11,272 acres were signed by 35 property owners, and 11,956 feet was drilled in 200 holes on these properties.

Jan 1, 1949

By G. Molinda, D. Dolinar

Each year, about 2,000 falls of supported roof occur in the more than 800 underground U.S. coal mines. Therefore to help improve the design of primary support systems, the National Institute for Occupational Safety and Health (NIOSH) conducted a nationwide study of roof falls in over 2,500 km of roadways at 37 coal mines. Information on the roof falls as well as other geotechnical, mining, geologic and roof bolting factors were collected and quantified Then a multi variate statistical analysis was conducted on the data with the roof fall rate being the outcome variable The results were used to derive preliminary design guidelines for predicting the roof bolt length, capacity, and pattern required to effectively reduce the roof fall rate. The equations are fairly limited by a relatively high statistical variance in the data. Also reported is a recent survey of U.S roof bolt manufacturers that shows a significant change in bolt types used over the last ten years.

By Jack E. Fraley

Because of their noncombustibility, silicate and magnesium oxycements are desirable for sealing shale in underground coal mines. In this Bureau of Mines investigation, cement samples were cured and tested (nonstandard tests) for submersion to note resistance to dissolution (breaking into parts), which is an important property for a coating. Nonappreciable dissolution during 1 week of submersion was set for passing the test. Over half of the coatings passed the test.

Jan 1, 1977

By R. E. Kennedy

"INTRODUCTION In a previous publication4 results were given of numerous experiments made on the in-flammability of gas mixtures consisting of methane, hydro a. carbon monoxide, nitrogen, and carbon dioxide. Data were obtained and tables prepared giving the inflammable limits of each of these combustibles when mixed with various proportions of carbon dioxide and nitrogen. By the use of these data and the application of Le Chatelier's law, it was found possible to calculate the limits of inflammability of any gas mixture containing any or all of the above gases.Various mixtures of the five gases given above were prepared and their limits determined experimentally and then calculated. Good agreement was found between the determined and calculated results when complex gases encountered in mine safety work were tested. Of special significance was the accurate calculation of the limits of inflammability of gases from mine fires, gases from mine explosions, detonation products of explosives, blast—furnace gases, automobile exhaust gas, and other gases of a similar character.Using the method given in the above report, Yeaw5 investigated a number of industrial gases including oven, coal, producer, blue, carbureted blue, and dry quencher gases, and found the determined and calculated results to agree remarkably well, thus giving further proof of the value of such a means of determining dangerous conditions when combustible gases are encountered in practice.GASES FROM A POTASH MINEGases were recently encountered in a potash nine in New Mexico, containing the com-bustibles, methane, hydrogen, and ethane. In one special case a mild explosion occurred when these gases were mixed with the right proportions of air and ignited it therefore became necessary to know the inflammability of these mixtures in order that the proper precautions could be taken to prevent explosions."

May 1, 1932

By Charles M. Mason

The Bureau of Mines evaluated equipment and procedures for drop-weight testing of explosive liquids as prescribed by Test 4) a widely used method. It was demonstrated that partial ignitions, originally designated as negative results, should be designated positives; it was also shown that wear or erosion of the sample cups and the type of mount used for the apparatus had important effects on the results. Relative sensitivity as measured by Test 4 was found to vary slightly with temperature. The Bureau also designed a fixed 2-kg weight and associated electromagnetic release, which subsequently were incorporated as standard in a revision of Test 4. The original concept that the test involves only adiabatic compression was found to be an oversimplification; an alternate mechanism for the initiation process is proposed in which due consideration is given to the effects of cavitation and microjets.

Jan 1, 1966

By J. E. Meacham

The U.S. Bureau of Mines investigated recovery of manganese from basic oxygen furnace (BOF) steelmaking slags because the slags represent a large potential resource of a metal for which there is no domestic production. BOF slags were leached using fluosilicic acid, a byproduct of the fertilizer industry. Manganese and iron were extracted as soluble manganous and ferrous fluosilicates while the calcium and magnesium remained in the tailings as insoluble fluorides. Treating the pregnant liquor with sodium chloride, precipitated sodium fluosilicate (Na2Sif6) which was recovered as a byproduct. Manganese and iron were precipitated as hydroxide-carbonate salts with the addition of sodium carbonate to the treated liquor. Recoveries for manganese and iron were 73 to 83 and 67 to 70 pet, respectively.

Jan 1, 1991

Safe operation and system integrity are two important properties of a mine hoist electrical system. Previous methods used to assess these systems, though rare, have involved extensive downtime and required skilled personnel. The recommended design considerations presented in this report are for a proposed automated system that will perform real time measurements, calculations, and recordings of pertinent performance data. Included are equipment installation and test procedures to be used with the system. The report also contains descriptions of the hoist performance criteria, and how they are to be collected.

Jan 1, 1985

By L. B. Pankratz

Low-temperature heat capacities, high-temperature enthalpy increments, and the enthalpy of formation at 298° K were determined calorimetrically for vanadium subnitride (VN0.465). The low-temperature investigation gave S°298.15 = 6.379 ±0.005 cal/deg mole, and a combustion calorimeter investiga¬tion provided ?Hf°298.15 = -31.80 ±0.60 kcal/mole. The two quantities were combined with the high-temperature data to give standard values of enthalpies of formation and free energies of formation above 298° K. These and related thermodynamic functions were tabulated to 1,800° K. Similar data are included in the range of 298° to 1,600° K for the mononitride, VN.

Jan 1, 1971

By R. R. May

A preliminary examination of the Houston strip-coal mine, situated on the Alaska Railroad at milepost 175 (61 rail miles north of Anchorage, Alaska) and a review of all available information resulting from early coal exploration activities in the area resulted in plans to investigate the coal-bearing formations at depth by means of diamond core drilling to indicate the existence of additional reserves of coal in close proximity to railroad transportation, where it would be quickly available to meet rapidly expanding military and civilian fuel requirements. From the date of mobilization of equipment, August 28, 1951, until date of suspension, August 18, 1952, 2,010 feet of diamond drilling was completed. Ten definable coal beds were cut, of which 2 appear to be persistent and minable over an area of approximately 1/2 square mile. Within this area the 2 minable beds contain approximately 5,000,000 tons of coal in place. Of the remaining beds, at least two others may be minable to the eastward near their projected outcrops; however, these and deeper beds (at least in the vicinity of the drill holes) lie beneath a zone of pressurized gas and brackish water. From a practical standpoint, continued development and utilization of the coal in this vicinity will depend on the operators' ingenuity in developing cheap mining methods and on diligent prospecting for strippable coal under the comparatively light glacial cover.

Jan 1, 1957

By M. R. Geer

Full-seam mining with continuous mining machines in dirty coal beds may increase loss of coal in the washery refuse. At one mine mentioned in this report the loss of salable coal was increased sixfold. Cleaning trials were made on three samples of jig refuse in a dense-medium pilot plant to demonstrate the application of this process to the recovery of coal from waste. These tests demonstrated that coal could be separated from impurity with the same degree of sharpness obtained in treating raw coal by dense medium. However, the recovery efficiency achieved in treating refuse averaged distinctly lower than that possible with raw coal because of the greater proportion of intermediate-density material in the feed and the lower yield of clean coal.

Jan 1, 1955

To rapidly limit and interrupt high dc fault currents with minimal arcing in the mine atmosphere. Approach Design a dc switching sys-tem which uses a pressurized, liquid metal-filled, change-of-state device combined with a conventional interrupter and commutating switch. Direct Current Interruption Switching and interruption of large direct currents imposes severe loads on fuses, contactors, and circuit breakers in mine power systems. This problem is much more pronounced with de than with ac because of the lack of a natural current zero in dc. Dc interruption is characterized by persistent arcing that can foul contact tips and con-tribute to interrupter failures. To reduce maintenance and prolong the service life of these units, a commercially viable dc switching system has been developed by the Bureau of Mines through a research contract with the University of Pittsburgh. This system rapidly limits and interrupts high fault currents when used in combination with conventional interrupters.

Jan 1, 1983

By John W. Buch

This is the first progress report to be released on the anthracite, mechanical mining research and engineering development program of the Bureau of Mines. This phase of Bureau work, which was initiated as an aid to stimulating wartime production of anthracite, has been continued after the war to assist primarily in improving the general economic position of the anthracite industry. Field work was started in. the 1945 fiscal year with the cooperation of an advisory committee representing management, labor, and the Commonwealth of Pennsylvania. For a beginning, several matters were suggested by members of this advisory committee as being worthy of investigation, and sections of underground mines yore offered for test purposes. Among the suggestions accepted for investigation was the problem of increasing the rate of advance for driving gangways in thin, steeply pitching anthracite beds 4 to 6 feet thick and pitching 60 degrees or more. The problem was undertaken as a field study, and this report relates to accomplishments on this project to June 30, 1947.

Jan 1, 1949