Search Documents

By James J. Snodgrass

A new technique was used to obtain detailed sonic logging data in drill holes above the water table at a coal mine site in northeastern New Mexico. The equipment was developed under contract to the Bureau of Mines and the U.S. Department of Energy to indirectly evaluate the in situ structural properties of coal and overburden. The system comprises a hydraulically operated, wall-clamping downhole probe compatible with standard four-conductor logging cable, and a surface control module. Resolution of layering is 0.6 meter (2.0 ft), and a redundancy of data from separate receivers provides accurate timing measurements. Preliminary results in the settled overburden of an excavated long-wall panel indicated a low average velocity zone, extending approximately 18 meters (60 ft) into the immediate roof of the coal seam. Subsequent measurements improved the field and recording procedures to produce high quality waveforms from which both P and S arrivals may be visually interpreted. Over a representative section of interbedded sandstone, siltstone, shale, and coal, Vp and Vs varied considerably even within lithologic units. Compressional wave velocity in the coal seam, Vp = 1,740 m/sec (5,700 ft/sec), was in the range of variability of published data.

Jan 1, 1982

By Verne E. Hooker

The Bureau of Mines conducted a preliminary investigation to determine the state of stress in crystalline rock outcrops near Atlanta, Ga. The secondary principal stresses in a horizontal plane near the surface are compressive and are 500 to 3,000 psi. The maximum compressive stress is northeast-southwest in the Stone Mountain-Lithonia district but changes to northwest-southeast near Douglasville. The elastic constants were determined from data obtained by static and dynamic laboratory methods and in situ velocity measurements. Results show Young's modulus to be dependent upon both stress level and anisotropy in the rock. Average secant moduli obtained from triaxial tests were used to compute the applied stress from borehole deformation measurements.

Jan 1, 1966

By Edward A. Barrett, Roberta A. Calhoun

MORE THAN 30 MILLION EMPLOYEES each year are exposed to hazardous occupational noise, and approximately one-third of them develop permanent hearing loss (NSC, 2000). Possible explanations for the latter statistic include worker regard for noise as a mere nuisance rather than as an occupational safety and health hazard, and consequent neglect of established protective measures (e.g., hearing protection); lack of knowledge concerning noise; improper use of hearing protection; worker indifference; and inadequate training (Bauer & Babich, 2004). Many drill rigs generate high sound levels, which vary according to the type of machine, its location with respect to the physical surroundings, and the location of the sound measured around the rig. A NIOSH study measured noise output from several types of drill rigs during field investigations (Ingram & Matetic, 2003). Two types of data were recorded the actual noise generated by the drill rig at various positions around the rig and the noise to which the drill operator was exposed during the drilling cycle. For the latter, sound level measurements up to 120 dBA were recorded while hammering casing (metal on metal) in drilling a water well (Photo 1). Several types of administrative controls exist to address worker exposure to loud drill rig noise. Rotating duties to decrease exposure time and posting warning signs in high-noise work areas are two such controls. Another is the use of hearing protection. Worker use of hearing protection has been disappointing, however. One study by the University of Michigan found that construction workers used earplugs and earmuffs only between 36% and 61% of the time that they were necessary (Lusk & Kerr, 1998). In a 2001 study, OSHA reported a relatively low rate of 30.4% for use of earplugs among construction workers (Walker, 2001). Why are rates for hearing protection use so low? One explanation may be workers' lack of concern for noise in the workplace. They expect workplace noise to be a loud and in¬ evitable nuisance and, therefore, accept it as part of the job. As a result, they disregard proven measures that can protect their hearing. Other workers may use hearing protection, but do so improperly. They may misguidedly remain in high-noise areas for extended periods thinking they are protected when in fact they are not. Other reasons for low use and/or misuse of hearing protection include poor education, lack of awareness and inadequate training (Nash, 2003). To address the training issue, NIOSH developed two exercises from which drillers can learn about noise, hearing loss and hearing protection. The first is an invisible ink exercise, titled "Drill Rig Incident" (DRI) (Photo 2); the second is a 3-D slide reel training aid, "Wearing Hearing Protection Properly" (WHPP) (Photo 3). DRI is an instructor-

By Robert M. Doerr

The oxidation kinetics of Ni-Y alloys in the range 0.04 to 8 weight-percent Y, and of high-purity Ni, were compared by the use of a sensitive volumetric apparatus. The reactions followed approximately the parabolic rate law; for oxidations in 02 at 0.5 atm and 1,200° C, the parabolic rate constant was about 0.37 + (0.064) (Y-2.11) mg cm-2 min-1/2, where Y represents the weight-percent Y in the alloy. Internal oxidation of Y occurred in the alloy specimens and the resultant Y203 particles, which were in patterns related to the eutectic structure of the alloys, served as markers showing that the subsequent oxidation of the surrounding Ni was by inward diffusion of O. The scale consisted in each case of NiO, but the inner parts of the scale on the alloy specimens included the patterned Y203 particles. The thicknesses of the inner parts of the scale depended directly on the Y concentration, and the thicknesses of the Y2O3-free outer parts of the scale were inversely related to the Y content of the alloys. There is thus a relationship between the thickness of the outer part of the scale and the protectivity of the scale. Outward diffusion of Ni and inward movement of 0, from the inner boundary of the Y2O3-free part of the scale, is proposed as a mechanism for these results.

Jan 1, 1966

By N. O. Johnson

This is one of a series of-Information Circulars dealing with mining and milling methods and costs at mines in various districts in the United States. The Hog Mountain gold mining district is of the northern edge of Tallapoosa County, in the east central part of the State of Alabama. The district is equally close to Goodwater and to Alexander City, both stations on the main line of the Central of Georgia Railroad. From Alexander City the mine is reached by 13 miles of graded road, traveling in a northeast direction. In dry seasons the road is good; in wet weather it is bad but passable. Improvements are being made constantly on the road, so that in the near future the gravel road should be good under all weathered conditions.

Jan 1, 1936

By George A. Morgan

There was little change in the mineral industry of Benin in 1986, as the economy remained in the grip of a regional recession exacerbated by failing oil prices, which nullified much of the income from Benin's oil production. Benin's industrial sector accounted for less than 10% of the gross domestic product (GDP), with the mineral industry providing about one-half of that total. Several major projects initiated over the last several years continued to perform and/or progress below Government expectations. These included the Save sugar refinery, the Dassa-Parakou section of the Dassa-Cotonou highway, the Benin-Togo Nangbeto hydroelectric plant, the Onigbolo cement plant, and the Semé Oilfield. Funding for these projects is the major source of the Beninese external debt, which was estimated to be over $800 million.2

Jan 1, 1988

By George S. Rice

"The successful use of the gas mask by the American Army it France in combatting the poisonous gases of German .shells caused many Army men to feel that the as masks were proof against any kind of gas which might be encountered. The result has been that from time to time there have been reported in the press, deaths of former army men through using their masks to enter various kinds of gases such as illuminating gas, gasoline vapor, and the gaseous atmospheres produced by mine fire. Such a case has just been reported from a mine, in Copperopolis, California, where a former Army man lost his life in descending a mine shaft filled with the fumes of a mine fire. Another man who, in attempting to rescue him, merely used a dust respirator, lost his life also.While the American type of the Army gas mask was developed by the Bureau of Mines for the War Department, and since the war a section of the Bureau's in¬vestigative force has been developing industrial gas masks for certain specificgases, the Bureau has repeatedly called to the attention of the public the fact that such masks have serious limitations and in no case should a gas mask be used in underground workings for the reason that there may be an insufficient amount of oxygen to breathe, (and the gas mask does not supply oxygen) or there may be present carbon monoxide, which the Army mask will not remove, and there always is some carbon monoxide produced by a mine fire or by a coal-mine explosion, or by a blast of dynamite or other explosive.It is true that the Bureau has been developing a mask which may take care of a small percentage of carbon monoxide, that is, one per cent and under, but in mine fires and after explosions, there may be, and frequently is, a much larger percentage of carbon monoxide in the mine atmosphere. Masks such as these, for small percentages of carbon monoxide and associated gases are for use in connection with industrial surface plants, as for example, on the top of a blast furnace or around gas producers in the open air."

Oct 1, 1920

Unfortunate occurrences resulting in injuries, loss of life, and destruction of property by explosion, fire, and other mishaps during shaft sinking focused the attention of the Bureau of Mines on the need for safety standards For such operations. Information Circular 7810 was published to meet that need. The current revision updates and replaces IC 7810. Several States have some rules and regulations applicable to local conditions, and several Bureau publications (including some now out of print) cover the hazards that may be encountered in shaft sinking. Certain requirements of the Federal Mine Safety Code and Federal Coal Mine Safety Act may be applied, but there are no definite, uniform standards that will guide those desiring to sink a shaft safely and bring about uniform safety inspections.

Jan 1, 1968

Develop a user-friendly, personal computer-based numerical modeling program that performs structural analyses of underground tabular deposits, making these readily available to the mining industry. Background When ore is extracted from an underground mine, the overburden weight is redistributed to unmined areas, recompacted gob zones, and artificial structures such as packwalls and/or cribs. This redistribution of stresses continually changes throughout the mining cycle and can be especially complicated when multiple-seam mining is involved. Numerical mine structural analysis methods provide a way of calculating the redistribution of overburden stresses and the resulting loading for any given area of an underground mine, thus enabling engineers to design safer and more productive mines. In 1973 Crouch and Fairhurst developed a mine structural analysis computer program called MINSIM. This computer program was based on the three-dimensional displacement-discontinuity approach, a subvariation of the boundary-element method. In 1979 Sinha expanded MINSIM's capability to provide an analysis of parallel multiple seams. Sinha called his program MULSIM. During 1984 and 1985, the Bureau of Mines upgraded and completely restructured MULSIM into what is now called MULSIM/BM.

Jan 1, 1990

By C. R. McCann

The Bureau of Mines conducted an experimental study of conditions needed to produce flames of pulverized coal when the heat needed for ignition is sup-plied only from the flame and hot furnace refractory. An electrically heated furnace which burned about 1 pound of coal per hour was designed and fabricated. A sheath of air, surrounding the primary coal and air stream, was used to prevent entry of hot gases from recirculating combustion products. Furnace temperatures needed for ignition ranged from about 1,8300 F for an Illinois coal to 2,250° F for a Beckley seam coal. Apparent flame velocities were about 2 to 5 feet per second, increasing with volatile content of the coal and with distance from the burner mouth to the flame. The time required for ignition, approximately 0.02 to 0.07 sec, was a better measure of flame behavior than was velocity.

Jan 1, 1969

By R. F. Zaffarano

Data presented on the physical characteristics of the reservoir oil, Aneth field, represent the initial phase of a study of Paradox basin reservoir oils being made by petroleum engineers of the Federal Bureau of Mines, Petroleum Research Center, Laramie, Wyo. The purpose of the study is to determine the original reservoir-oil characteristics in several important new discoveries in the Paradox Basin and to investigate correlations between the properties of these reservoir oils and structural or areal position within the basin, If migration is limited and oil accumulates near its source, then it seems probable that few differences should be found in the composition and characteristics of reservoir oils occurring in given age rocks and within the confines of a geological basin. Within these limits, conditions that effected the formation of oil and its transfer from parent to storage rocks probably were rather uniform in an area the size of most of our geological basins. However, if oils should migrate considerable distances, it seems logical to expect that the relative quantities of gas and liquid components may differ in traps occurring along the direction of migration, corresponding with the theory of differential entrapment (5).4/

Jan 1, 1959

By J. H. Rose

This paper describing the milling practice at the Magma Copper Co., Superior, Ariz., is one of a series being prepared by the Bureau of Mines on milling methods and costs in the various mining districts throughout the United States. ACKNOWLEDGMENT The authors wish to acknowledge their indebtedness to William Koerner, general manager of the Magma Copper Co., for permission to prepare this article; to J. S. Garrott, former mill superintendent, for the historical facts; and to Walter Cooksley, general foreman, for his assistance in obtaining the data.

Jan 1, 1930

By James Paone

The Bureau of Mines made drillability studies with impregnated diamond bits in the laboratory on 7 rock types and in the field on 21 different rock types. Results indicate that drill parameters of rotational speed, thrust, and torque must produce sufficient applied forces to induce stress levels that cause continuous failure in rock to achieve efficient penetration rates. Higher rotational speeds appear to be more effective in drilling relatively harder rocks, although the increased speed causes more bit wear; increases in thrust result in higher drilling rates but not linearly; and up to a critical value a linear relation exists between torque and penetration rate for a specific rock type. Penetration rates with impregnated bits show a trend similar to that obtained with surface-set bits for rock under 25,000 psi compressive strength.

Jan 1, 1966

By Frank B. Fulkerson

A study was made of scrap iron and steel in the South Central States in order to determine trends in processing, shipment, and consumption of this important commodity. These data were derived in part from statistical sources and in part by visits to scrap yards and steel mills. Trends in the industry were reviewed. Dealers in 1963 supplied 1.8 million tons of iron and steel scrap to steel mills and foundries in the south-central area, compared with 2.1 million tons in 1955. Most of the scrap was processed and shipped within 200 to 300 miles of consuming centers. Exports provide a principal outlet for dealers along the gulf coast. Most of the scrap that fills these orders is loaded onto freight cars at yards in Texas and Louisiana and -is shipped to ports for direct transfer from railroad car to ship. The tonnage exported varies greatly from year to year. The largest scrap operations are in or near large cities which are heavy scrap generating areas, steel mill sites, or port cities for export of scrap. A tentative analysis indicates that the short-run supply of prepared scrap is inelastic to price changes; therefore, buyers probably arc in a strong bargaining position at times of declining demand. One technological development in the iron and steel scrap industry is the use of large presses which can take complete automobiles with frames, wheels, springs, and other heavy parts still intact and reduce them to bundles. At Houston, Tex., and Kansas City, Mo., shredding plants are in operation that reduce car bodies and other light scrap into flat pieces 4 to 6 inches in size.

Jan 1, 1966

By Launa Mallett

This training material focuses on the content of emergency warning messages. Research has shown that when an emergency occurs, people often do not get the information they need for the purpose of taking appropriate action. This safety talk presents a procedure, using mental cues that can be used by senders and receivers of emergency warnings.

Jan 1, 1999

By Kermit G. Davis, Sean Gallagher, William S. Marras, Kimberly Kovacs

This study evaluated spinal loads associated with lifting and hanging heavy mining cable in a variety of postures. This electrical cable can weigh up to 10 kg per metre and is often lifted in restricted spaces in underground coal mines. Seven male subjects performed eight cable lifting and hanging tasks, while trunk kinematic data and trunk muscle electromyograms (EMGs) were obtained. The eight tasks were combinations of four postures (standing, stooping kneeling on one knee, or kneeling on both knees) and two levels of cable load (0 N or 100 N load added to the existing cable weight). An EMG-assisted model was used to calculate forces and moments acting on the lumbar spine. A two-way split-plot ANOVA showed that increased load (p<0.05) and changes in lifting posture (p<0.05) independently affected trunk muscle recruitment and spinal loading. The increase in cable load resulted in higher EMG activity of all trunk muscles and increased axial and lateral bending moments on the spine (p < 0.05). Changes in posture caused more selective adjustments in muscle recruitment and affected the sagittal plane moment (p < 0.05). Despite the more selective nature of trunk EMG changes due to posture, the magnitude of changes in spinal loading was often quite dramatic. However, average compression values exceeded 3400 N for all cable lifting tasks.

By C. I. Pierce

The Bureau of Mines conducted laboratory tests to determine if ultrasonic energy could reduce either the residual water or oil content of petroleum reservoir-rock samples from Appalachian area oilfields. Brine-saturated core samples were flooded with oil to residual brine saturation and subjected to 20 kilocycles per second ultrasonic energy. Then they were flooded with brine to residual oil saturation and again subjected to ultrasonic energy. Additional water displaced as a result of the application of ultrasonic energy to the flow system ranged from 0 to 4.3 percent of the original brine and averaged 1.9 percent. The increase in oil recovery as a result of the ultrasonic energy ranged from 0 to 9.0 percent of the original oil and averaged 3.1 percent. On the basis of the tests, it appears that 20-kcps acoustic waves would not have field application for oil recovery.

Jan 1, 1968

By D. A. Buckingham

The Bureau of Mines evaluated potential availability of domestic nickel from 23 deposits, Evaluations included an estimation of in situ and recoverable resources, applicable mining and processing technologies, and capital and operating costs. Discounted cash flow analysis with a 15-pct rate of return was used to determine the average total cost of production of each operation, Identified in situ resources contain 9.0 million metric tons (t) of nickel; 5.5 million t is recoverable as nickel metal or ferronickel. Demonstrated in situ resources contain 8.2 million t of nickel; 4.8 million t is recoverable as nickel metal or ferronickel. No nickel is available at a total cost of production equal to the January 1983 market price of $3.24 per pound. Analyses indicate that potential annual production can only meet current consumption levels at a total cost of production of $7.60 per pound of nickel, Nickel&apos;s availability is contingent on (1) successful adaptability of nickel processing methods to domestic resources, (2) location of a smelting facility, and (3) marketability of byproducts and coproducts. Analyses were performed on the effects of byproduct and coproduct revenues, energy, labor, and transportation costs, and metallurgical recoveries on nickel&apos;s availability.

Jan 1, 1984

By P. H. Floyd

This report presents the results of laboratory beneficiation tests on a sample of scheelite ore and a sample of low-grade scheelite flotation concentrate from the Sangdong mine, Korea. Sangdong was the foremost producer of tungsten concentrates on two occasions - during part of World War II and in 1953. It was also a significant producer of bismuth concentrates. Resources are very extensive and could support a 5,000-ton annual output of tungsten concentrates for many years. Located in the eastern part of South Korea near the 37° latitude, Sangdong has been a vital source of dollar income for the Republic of Korea in recent years. Its shutdown in March 1954 came about as a result of the great decline of tungsten prices and the fact that a sales contract with the United States Government had been terminated, In addition to establishing new markets, the problem of reopening Sangdong will be related to cost reductions and improving mill recoveries. Large quantities of offgrade scheelite concentrates were produced in the past and shipped to the United States for further beneficiation. Other low-grade concentrates and middlings have been stockpiled or discarded at the mine plant.

Jan 1, 1954

By H. H. Schrenk, L. B. Berger, W. P. Yant, F. A. Patty

"The use of small such as canaries and white mice, for detecting carbon monoxide depends primarily on the fact that the volume of respiration of these animals in proportion to their volume of blood is much higher than for man. Accordingly, when animals and men are simultaneously exposed to a given concentration of carbon monoxide the animals will absorb it more rapidly and attain serious poisoning in less time than men. Prom a practical viewpoint the use of the animals depends on the margin of time between observable symptoms in them and serious poisoning in man, during which man can return to fresh air or use respiratory protection. It should be remembered, however, that during the time the animal is incurring a detectable degree of poisoning, man is also absorbing some carbon monoxide, and the margin of time is not very wide. Experience with canaries has shown that an occasional specimen may have a tolerance above the average of the species and fail to exhibit symptoms before man incurs a very discomforting and possibly a serious degree of poisoning.It is also well known that physical activity increases the demand for oxygen by the body, and the respiratory exchange and circulation of the blood are increased to meet the demand. This sets up a vicious condition if carbon monoxide is present in the air because the rate of absorption of carbon monoxide is not only increased by the increase in respiration and circulation, but the absorption of carbon monoxide decreases the capacity of the blood for carrying oxygen at a time when the demand is high. These facts, together with the increase in respiration and circulation which attend excitement, underlie the caution to be calm and to walk slowly and to reduce physical exertion to a minimum when exposed to carbon monoxide. For these same reasons, when using animals for detecting carbon monoxide it is endeavored to keep them active, thereby tending to increase the response of the birds and widen the time between observable effects in the birds and effects in the man. As rule canaries are kept fairly active through fright at the unnatural surroundings and in their endeavor to remain on the perch of the cage when carried into the atmosphere to be examined. They also experience an excitement stage with oncoming carbon monoxide poisoning. Sometimes, however, especially if the air is cold, they tend to be inactive and quiet. Ordinary mice and white mice become inactive with use and also with oncoming poisoning. They huddle in the corner or the cage, and thereby not only reduce their sensitivity but make it difficult to observe signs of poisoning."

Oct 1, 1930