Search Documents

By Donald J. Barnes

Gold was found in samples collected from Pleistocene and Holocene stream and terrace deposits. Approximately 15,000 cu yd (11,400 cu m) of small and discontinuous terrace and stream gravel deposits in the study area are composed of material derived from sedimentary and granitic rocks. The detritus is subangular to subrounded, and poorly sorted, ranging from boulder to sand size. Gold values in samples collected averaged 8.2 cents per cu yd (gold value of $500 per oz). Pan concentrates and rock chip samples collected from reported mineralized zones showed an absence of economic minerals. Stream placer deposits are uneconomic. No potential was observed for metallic or nonmetallic minerals in the La Panza study area. No potential exists for gas, oil, or coal resources.

Jan 1, 1981

By H. D. Hess

This report presents the results of laboratory mineral evaluations conducted by the federal Bureau of Mines under the joint sponsorship of the U.S. Atomic Energy Commission (AEC) and the Bureau a! Ships, U. S. Department of the Navy. The major purpose of this investigation was to examine and evaluate zirconium minerals representing sizeable deposits in an effort to locate com¬mercial sources of high-hafnium ores. Although determination of the hafnium content was the principal objective, each of the zirconium minerals also was analyzed for combined zirconium-hafnium oxide, silica, uranium, thorium, yttrium, and cerium. The general laboratory procedure involved microscopic examination of the test samples, concentration of the hafnium-bearing zirconium mineral by standard laboratory techniques, and analysis of the derived concentrate by quantitative microscopic, chemical, and X-ray spectrographic methods. Of the several hundred samples tested under this program, 147 are discussed in this report, including 94 from domestic occurrences and 53 from widespread foreign sources.

Jan 1, 1962

By A. W. Hall

A neutron meter was developed for monitoring the sulfur content of coal streams. Neutrons from 80 micrograms of californium-252 penetrate the coal, producing thermal neutrons that are captured by atoms of elements present in the coal. The excited atoms emit prompt gamma rays with energies characteristic of the capturing element. These gamma rays are detected with a 6-by 7-inch sodium iodide detector and processed by electronic equipment to produce a gamma ray energy spectrum of the elements. Tests of the meter at a commercial coal preparation plant showed that sulfur in moving coal can be determined to a precision of 0.05 percent sulfur within 2 minutes. Based on this report by the Bureau of Mines, reliability of the coal-handling system proved inadequate for long-term operation, however, and improvements are planned.

Jan 1, 1975

By D. Eugene Rannels, Sarah E. Dunsmore, Cara Martinez-Williams, Yu-Chen Lee

"Dunsmore, Sarah E., Yu-Chen Lee, Cara Martinez Williams, and D. Eugene Rannels. Synthesis of fibronectin and laminin by type II pulmonary epithelial cells. Am. J. Physiol. 270 (Lung Cell. Mol. Physiol. 14): L215-L223, 1996.Previous investigations demonstrated that type II pulmonary epithelial cells regulate extracellular matrix deposition as a function of time in primary culture. In those studies, the matrix fraction was analyzed as a whole. The present work focused on two components of the type II cell matrix, fibronectin and laminin. These glycoproteins have differing effects on differentiation of type II cells in primary culture. Fibronectin synthesis was quantitated between day 1 and day 6 in the cells, matrix, and medium; laminin synthesis was quantitated only in the cells. Although total fibronectin synthesis was regulated as a function of time in culture, reaching its greatest value on day 2, the average proportion of newly synthesized fibronectin in the cells (35%), medium (50%), and matrix (15%) remained constant over a 6-day interval. Between day 2 and day 6, the relative abundance of fibronectin messenger RNA increased 6.5-fold. Rates of cellular laminin synthesis did not vary with time in culture. These results support a role for differential regulation of fibronectin and laminin synthesis to determine the composition of the type II cell extracellular matrix. INTERACTIONS BETWEEN THE pulmonary epithelium and alveolar basement membrane may play a role in the physiology and pathophysiology of the lung. Pulmonary epithelial cells and the alveolar basement membrane form one component of the blood-gas diffusion barrier. Integrity of this barrier is crucial to normal lung function. Specific domains of alveolar basement membrane components have been proposed to determine localization of type I and type II pulmonary epithelial cells during lung growth and development, as well as during repair of the alveolar surface after injury (13). In the injured lung, the extent of damage to the epithelium and the underlying basement membrane is thought to be a key factor to determine subsequent repair or fibrotic scarring (3)."

Jan 1, 1998

By James E. Hill

Tremendous improvements in mining technology have been witnessed during the past 100 years. For example, before 1860 all blastholes were drilled manually and blasting was done with low-energy black-powder. During the 1860's both the pneumatic rock drill and high-energy dynamite were introduced, ushering in an era of mining mechanization that has steadily progressed since that time. Today, with the rapid implementation of the latest advances in communication science, mining technology is moving into a new era that goes beyond mechanization as such. Transistors, transducers, scanners, telemetry, and the like, all terms largely derived from the new communication sciences, add up to what is popularly know as automation-the communication of machine with machine. Automation is now playing an important role in selected parts of the mining process, such as hoisting, hydraulic roof supports, and underground surface locomotive haulage and belt conveyor systems. But this year marked the first attempt to auto-mate the total mining process with the commencement of production at the British National Coal Boards Bevercotes mine. If this full-scale experiment proves successful, it could lead towards other fully automated mines in both Britain and other parts of the world. This decade, there-fore, could be considered the one that provided the foundation for the mines of the future.

Jan 1, 1966

By Charles E. Whieldon

The importance of producing more oil from known petroleum reserves has placed increased emphasis on the application of secondary-recovery methods. Recently published reports3 4/ describe the results of waterflooding in Roane and Pleasants Counties, W. Va. (see fig. 1.) This report describes the Barron Kidd Oil Co.?s Santee waterflood project, Maxton sand, Burton field, Church district, Wetzel County, W. Va. (See fig. 2.) The Federal Bureau of Mines hopes that these reports will stimulate interest in improved waterflooding techniques, thereby discouraging premature abandonment of oil leases.

Jan 1, 1961

By Lloyd H. Banning

Crucible-smelting tests at the Northwest. Electrodevelopment Laboratory and a pilot-plant test on electric smelting of western phosphate rock for the Westvaco Chlorine Products by the Tennessee Valley Authority indicated that the small vanadium content of the rock is concentrated in the ferrophosphorus by-product of Phosphorus smelting. This research is concerned' mainly with recovering vanadium and phosphorus froth the ferrophosphorus produced from western phosphate rock. Exploratory tests were made of several methods of treating vanadiferous ferrophosphorus. Attempts to separate vanadium as a carbide dross by saturating molten ferrophosphorus with carbon were unsuccessful. Volatilization of phosphorus from ferrophosphorus was accomplished to some extent, both with and without addition of sulfur in several forms, but elimination of phosphorus was not complete. Brief testing in a small experimental converter on oxidation of vanadium and phosphorus; into a slag by blowing with air showed promise. A method that comprised fusing vanadiferous ferrophosphorus mixed with soda ash under oxidizing conditions gave encouraging results and was tested beyond the preliminary stage. A slag product of the fusion contained most of the phosphorus and vanadium as water-soluble sodium phosphate and. virtually water-insoluble sodium vanadate. After leaching the sodium phosphate froth the slag, the leach residue was reroasted with soda ash and salt. This roasted product was leached again with water to extract the vanadium.

Jan 1, 1951

By M. E. Tyrrell

Research objectives were to determine the reasons for erratic behavior of semisilica horizontal zinc retorts in service; to investigate potential corrective measures including the possible utilization of more refractory materials in the retort body; and to delineate laboratory tests suitable for process control in the manufacture of retorts. Correlation of laboratory test results and data supplied by the cooperating smelters indicated that structural failures due to thermal shock and laminations in the retort body are largely responsible for the erratic behavior of horizontal zinc retorts in service. The most promising modifications made in the retort body and evaluated on a laboratory scale included finer grinding of the plastic clay fraction, substitution of mullite grog for calcined fire clay and grain alumina for silica, plus the use of an organic binder. Lamination-free extrusions having excellent thermal shock resistance were prepared from a mixture composed of 50 percent low-silica Missouri plastic clay through 100 mesh, 25 percent mullite grog through 6 mesh, and 25 percent alumina through 100 mesh. The mix was pugged under 28-inch vacuum with 1 percent ligno sulfonate binder in 12 percent tempering water. Laboratory tests suitable for process control in the manufacture of retorts are described.

Jan 1, 1969

By H. R. Babitzke

The purpose of this investigation was to develop an alloy of columbium for use at high temperatures and for nuclear applications. The properties of possible alloys were determined, and the more promising ones were selected for further improvement. Criteria for selection were machinability, hardness, workability, tensile strength, and oxidation resistance. Thirteen 100-gram ingots, ranging from 100 percent columbium to 100 percent vanadium, were prepared and subjected to various tests. Also included for comparison were zirconium and the zirconium alloy, zircaloy-2. Test results showed that a columbium alloy, containing 10 atomic percent vanadium merits further development. Besides being workable at room temperature, the columbium-10 atomic percent vanadium alloy has oxidation resistance superior to the other alloys of the series and is also superior to zirconium or zircaloy-2. The latter two materials have comparable neutron-absorption cross sections. The strength and hardness values of the alloys tested were found to increase with increasing vanadium content, reaching a maximum at 50 atomic percent vanadium and decreasing with further increase in vanadium. This behavior is typical of binary alloys wherein each element will retain any proportion of the other in solid solution. INTRODUCTION There is an increasing need for alloys for service at high temperatures. Since current world reserves of columbium metal approximate 1,500,000 tons (1),4 this metal is now readily available. Columbium can ties; be considered a practical base material for high-temperature alloys required in nuclear reactors and in aircraft and space vehicles. General requirements chosen are: (1) Workability, (2) satisfactory mechanical properties at temperatures approaching 1,000° C., and (3) resistance to oxidation at such temperatures.

Jan 1, 1962

By Jr. Sillers

This is the sixth report of investigations in cooperation with the steel industry to establish the technological acceptability of electrolytic manganese in steelmaking processes. The bulk of the .electrolytic manganese used in these tests was produced by the Bureau Of Mines from domestic ores at its Boulder City, Nev., pilot plant by the process developed by the Bureau. Electrolytic manganese for the first series of tests made in 1940 was supplied by the Electro manganese Corp., Knoxville, Tenn. The first report dealt with the application of electrolytic manganese to the manufacture of stainless.steel;9 the second with tests in acid electric and acid open-hearth low and medium carbon-steel castings; the third with its use in rimmed and? killed low-carbon steels; the fourth with its application to the manufacture of stainless steel as well as the Timken 16-25-6 alloy for gas turbines; and the fifth with tests in acid and basic electric steel foundry practice and basic steel ingot production.

Jan 1, 1948

By F. S. Crawford

Untreated timber in a mine or elsewhere may fail prematurely because it may "rot out before it wears out." If such timber is treated with a satisfactory preservative, decay will be retarded for many years, and it's serviceable life will beg prolonged to several times that usually obtained from untreated timber.4/ Treated timber has many advantages, and although it has been used extensively by railroads and other large consumers of structural timber, the relatively small use in mines seems strange indeed. Timber does not decay if it is kept dry, cool, and well-ventilated or if it is kept constantly wet or sumberged in water. At a mine in Canada the temperature in the upper levels was only 44° F., and the timber did not decay. As operations deepened, however, warmer ground was opened, and, with high humidity, conditions favored timber decay. The life of untreated timber may be only 2 to 3 years under such conditions.

Jan 1, 1951

By H. H. Schrenk

The purpose of respiratory protective equipment is to prevent the inhalation of harmful or objectionable atmospheres. Although constituents or contaminants that may render an atmosphere irrespirable or objectionable are numerous, they may be classified broadly as follows: I. Gaseous substance: n. A. Toxic. B. Inert (oxygen deficiency). II. Particulate matter (dispersoids). A. Solid. a. Dust (formed by disintegration). b. Pure (formed by condensation). B. Liquid. a. Mist (formed by disintegration). b. Fog (former by condensation).

Jan 1, 1940

By L. L. Hirst

Liquid fuel oils possess certain advantages over solid fuels. Ease in handling, precision temperature control, and almost complete freedom from ash are among those considered when a liquid fuel is selected for use in industrial processing. In some instances these fuels are desirable because more heating units can e packed in a Given space where space is limited, as on snips. In other cases the' are chosen because of lower actual cost per British thermal unit absorbed, or for control of the flame to increase the capacity of furnaces, as in steel and refining.

Jan 1, 1948

By L. G. Marshall

The geology, mining, beneficiating, types of products, and costs in terms of percent of total costs and of labor, power, and supplies of two crushed- limestone operations in Madison County, Iowa, are described in this paper. The operations are basically similar, differing in refinements in mining, product types, and markets. The operations are comparable as to personnel and as to weighted costs in terms of percent of total costs and in terms of man-hours, power, and supplies. The waste-to-stone stripping ratio is 1 to 0.8 at both operations, the powder factor is 0.29 pound of explosives per ton of stone, and daily production is 95 tons per man-shift. Both companies use crawler-mounted diesel shovels for loading, truck transportation, wagon drills, and dry screening.

Jan 1, 1963

By E. A. Clarke

The vapor-phase section of the Coal Hydrogenation Demonstration Plant at Louisiana, Mo., was operated for the first time in April 1949. The run lasted only 10 days because of time limitation (pending plant dedication in May) and the small amount of charging stock available. The primary purpose of the operation was to break in and determine the operability of the equipment and to supplement the operators' classroom training with actual practice by operating the plant under mild conditions. A secondary aim was to obtain data on the hydrogenation of petroleum oil and lignite tar distillate at approximately 10,000 p.s.i. while making gasoline and Diesel fuel oil. Although the operations were carried out under conditions considerably below those used in the plant design, a great deal of experience and data was obtained. As it is not feasible at this time to conduct further vapor-phase operations on similar stocks, this report has been prepared to present and summarize the data obtained through this operation.

Jan 1, 1950

By Melvin P. Silverman

The literature on methane-oxidizing bacteria is reviewed in regard to (1) the growth and isolation of cultures by special techniques; (2) the distribution of these organisms in nature and descriptions of individual species; (3) the physiology of methane-oxidizing bacteria as influenced by temperature, light, pH, aerobiosis versus anaerobiosis, and carbon and nitrogen sources; and (4) the biochemistry of methane oxidation revealed by studies with intact cells and subcellular systems. Present practical applications of methane-oxidizing bacteria are limited to prospecting for natural gas and petroleum deposits. Desirable areas for future research are discussed as well as some possible applications such as (1) the removal and/or early detection of methane gas in coal mines by intact cells or enzyme preparations; (2) the generation of electrical energy by microbial fuel cells using methane as fuel; (3) the growth of methane-oxidizing bacteria on methane for their food value; (4) the purification of hydrocarbon gas mixtures using methane-oxidizing or other alkane-oxidizing bacteria; and (5) the synthesis of methane from mixtures of H2 and CO or H2 and CO2 by me thane-forming bacteria.

Jan 1, 1964

By F. W. Brown

In 1942 the Explosives Division investigated electrostatic hazards associated with the manufacture, storage, and use of explosives. A report was issued in 19454/ presenting the data on the spark sensitivities of explosives. In 1948, the apparatus was redesigned and rebuilt to make the routine testing of explosives safer and more convenient. The rebuilt apparatus is described in this re-issue of the former report. Included are details of construction and a list of parts. PRINCIPLES OF METHOD In normal procedures without special precautions, it is possible for static charges to be accumulated on individuals or on ungrounded equipment or structures.5/ Static charges may be produced in many ways, but they are most commonly produced by rubbing or successive contact and separation of unlike surfaces, at least one of which is usually an insulator.

Jan 1, 1953

By John C. Gagliardi, Walter K. Utt

The U.S. Bureau of Mines, in cooperation with Carter Mining Co., conducted vibration tests of four off-road vehicle seats. The purpose of the tests was to determine which seat provided the best vibration attenuation under laboratory conditions. Laboratory tests were constructed to simulate the mining vibration environment within the limitations of the test equipment. The acceleration test levels and corresponding response of the seats were low compared to IS0 2631's fatigue-decreased-proficiency time limits. Two of the seats employed mechanical suspensions and two seats employed air suspensions. The seats were tested using a 22,241-N (5,000-lbf) electrodynamic shaker. Mechanical suspension seats were tested with various preload-to-mass ratios (PMR's) and cushion densities. Air suspension seats were tested with various air pressure levels and seat cushion densities. Air suspension seats provided good vibration attenuation if pressurized greater than 552 kPa (80 psi). Mechanical suspension seats' attenuation performance decreased if the PMR exceeded 9.8. Seat cushions of lower density provided less vibration damping.

Jan 1, 1993

By John C. Hartley

Three systems that monitor ventilating fans are described. These electronic monitoring systems automatically perform most of the operations required to conform with the provisions of the Federal Mine Safety Code in the event of fan failure or slowdown.

Jan 1, 1964

By A. B. Coates

During the last three years the use of ethylene glycol dinitrate4 (E.G.D.) as at low-freeze (L.F.) agent in place of nitropolyglycerin has become common in the manufacture of explosives of the dynamite type. The usual proportion of D. G. D. in the explosive "oil" is 25 per cent; the remainder, 75 per cant, is regular nitroglycerin. These proportions were probably selected as a continuation of the practice of 25 per cent nitropolyglycerin and 75 per cent regular nitroglycerin.

Jan 1, 1929