Search Documents

By T. E. Gray

This report describes the preparation characteristics of the more significant coalbeds in Butler County, Pa. It is one of a series planned to determine which coals are suitable for producing metallurgical coke, either as mined or after beneficiation. More than 2 million tons of coal was produced in Butler County in 1958, of which about 25 percent was cleaned mechanically in four cleaning plants. Updating the 1942 coal-reserve estimates made by Ashley to December 31, 1958, more than 1,266 million tons of recoverable coal reserves remain in the county in beds that arc 24 inches or more thick. The Upper and Lower Freeport, Upper, Middle, and Lower Kittanning, Clarion, and Brookville beds were selected on the basis of production and estimated minable reserves. Sample locations were chosen after a study of the literature, conferences with mining engineers and mining company officials in the field, and examination of the available sites. Four samples each were collected from the Upper Freeport and Middle Kittanning beds, three samples from the Brookville bed, two, samples from the Upper Kittanning bed, and one sample each from the Lower Freeport, Lower Kittanning, and Clarion beds.

Jan 1, 1960

By A. L. Engel

This report describes results of laboratory-scale experimental treatment of nine ores containing gold and silver, including samples of products of previous plant treatment, from ore deposits in California and Nevada. The samples treated were taken by engineers of the Bureau of Mines during investigations of these ore deposits. The information reported is of interest for development of the mining districts represented or in future Investigations of similar ores from other sources. The treatment methods were as simple as possible. More complicated treatments were tried when required, The applicability of the methods and their limitations in treating the ores are shown by the data in this report. The following treatment methods were employed in the experiments described: Screen analyses were made to determine distribution of values in various screened-sized portions of crushed ore, or to determine optimum size to which a particular ore should be crushed or ground to liberate values, and some-times to determine residual values in various-sized portions of treated material.

Jan 1, 1961

By Donald W. Mitchell

Certification tests for urethane-foam systems and techniques for apply-ing foam safely in mines are described. Fire hazard from foam exists if flame propagates beyond the ignition source or penetrates the foam. Foam that passes the certification tests can be applied on stoppings, continuous sections of ribs of relatively wide passageways (with no foam on the roof), short sections of roof such as overcasts, roof cavities, and intersections (with no foam on the ribs), and between buntons on one wall of a shaft. Foam on the ribs and adjoining roof presents a fire hazard. Stoppings covered with foam passing the certification tests are resistant to penetration of heat, flame, and smoke than similar stopping without foam. Flame propagation can be arrested by water sprays. Spontaneous ignition of foam can be prevented.

Jan 1, 1966

By Janet Torma-Krajewski

Research has shown that an ergonomics process that identifies risk factors, devises solutions to reduce musculoskeletal disorders (MSDs), and evaluates the effectiveness of the solutions can lower worker exposure to risk factors and MSDs and improve productivity. A review of the Mine Safety and Health Administration (MSHA) injury/illness database indicated that 46% of illnesses in 2004 were associated with repetitive trauma and 35% of nonfatal lost days involved material handling during 2001? 2004. Even though these statistics show that MSDs significantly contribute to occupational illnesses and injuries in the U.S. mining industry, few mining companies have implemented an ergonomics process. Despite the many unique challenges in the mining environment, three mining companies partnered with the MSD Prevention Team at the National Institute for Occupational Safety and Health?s Pittsburgh Research Laboratory to demonstrate that an ergonomics process could be systematically implemented and effectively integrated with existing safety and health programs. Because these three mining companies were very different in organization, culture, and size, the ergonomics processes had to be modified to meet the needs of each company. A description of how these three companies applied ergonomics and the tools and training used to implement their processes is given. Prior to discussing the case studies, general information on the elements of an ergonomics process is provided.

Feb 1, 2009

By W. P. Diamond, B. M. Bench, C. M. McCulloch

Coalbeds exhibit a directional permeability, with the maximum permeability oriented parallel to the face cleat. Thus, the most efficient pattern of vertical degasification holes for a coalbed is dependent upon cleat orientation. Surface joints, infrared photolinears, and Ronchi grating photolinears were investigated as potential estimators of subsurface cleat orientation. Cleat orientations were masured in 18 mines, in the Pittsburgh coalbed in southwestern Pennsylvania and northern West Virginia to be used as a standard against which prediction techniques would be evaluated. Two cleat systems with a strong geographic segregation were measured in the study area: N 67° W - N 28° E (95° separation) for the north, and N 76° W - N 17° E (93° separation) for the south. Directional data obtained from the three techniques investigated yielded satisfactory regional predictions of cleat orientation. Analysis of surface joints was the only technique considered sufficiently reliable on a local basis. Prediction of cleat orientation is based on the pairing of the principal directional sets into all reasonable combinations of fundamental systems. The system or systems composed of the most dominant sets nearest to 90° separation are likely to be a reliable prediction of cleat orientation. The most dominant set of the system selected is likely to be the face cleat.

Jan 1, 1976

By R. R. Wells

This report summarizes the results of preliminary mineral-dressing studies by the Bureau of Mines on five samples of copper-bearing ore from various Alaska de-posits. The work on each sample was not extensive enough to warrant individual publication. The results, however, indicate the possibilities and limitations of concentration of the respective ores. The information therefore may be helpful in future development of these ore bodies. Four of the five samples tested were submitted to the laboratory by engineers of the Bureau of Mines as part of the examinations and survey investigations of strategic-mineral deposits in Alaska. This program is conducted to assist development of mineral resources in the Territory and particularly to aid economic exploitation of marginal or complex ores. The fifth sample was submitted by engineers of the Defense Minerals Exploration Administration.

Jan 1, 1956

By D. J. Parker

Because of its convenience and availability, natural gas (and to a much less extent manufactured gas) in being used more generally throughout the country for domestic and industrial purposes. With this use, specific and little-recognized hazards have arisen owing principally to the fact that the public and the consumer lack knowledge of the explosive property of this fuel. During the past 8 years gas explosions hove occurred in public and private buildings with loss of more than 300 lives and injury to many others. Such appalling catastrophes can and will be prevented if and when the necessary precautions are taken in the construction of buildings and the installation and maintenance of gas lines and gas appliances, plus adequate supervisions inspection, and education.

Jan 1, 1941

By G. H. Keith

A vanadium-base alloy consisting of the following elements in weight-percent--molybdenum, 20; titanium, 10; carbon, 0.1; silicon, 0.5; and yttrium, 0.5--had exceptionally high strength at temperatures up to 1,200° C. This alloy was capable of fabrication to sheet of ~ 1 mm thickness by a combination of hot swaging and hot and warm rolling. In the warm-rolled condition at ambient temperature, its ultimate tensile strength was 1,205 MN/m2. The strength at 1,200° C was 150 MN/m2. Within the temperature range of 25° to 1,200° C, the ductility of the alloy as measured by elongation increased from 4 to >90 percent. Strengthening was achieved by both solid-solution and dispersed-phase mechanisms. Alloys of 20 percent molybdenum and 10 percent titanium were stronger than the other molybdenum-titanium alloy compositions tested. Strength was increased 15 percent in the temperature range of 25° to 800° C, with no accompanying loss in ductility, by the addition of 0.5 percent silicon. Workability was improved by additions of 0.25 and 0.5 percent yttrium.

Jan 1, 1970

By William H. Pomroy

This report describes Bureau of Mines research that led to the design, prototype fabrication, and successful proof-of-concept testing of an improved stench fire-warning system for underground noncoal mines. Stench systems are the most widely used means of warning driers in underground noncoal mines of fires or other emergencies. A stench system alerts miners that an emergency condition exists by injecting an odorant into the mine air. Although stench warning systems have been used successfully for over 60 yr, present systems suffer several serious shortcomings, including odorant toxicity, unreliability of warnings, widely varying stench concentrations, and others. In 1980, the Bureau began a research program to upgrade the stench warning system. The resultant system overcomes the deficiencies of existing systems by substituting tetrahydrothiophene for the commonly used ethyl mercaptan stench odorant, and through the use of a specially designed stench injector. The improved injector reliably meters stench fluid into either ventilation-air or compressed-air streams at a precisely controlled rate. Prototype hardware has been fabricated and proof-of-concept tested under bath laboratory and in-mine conditions.

Jan 1, 1985

By John Nagy

The Bureau of Mines adapted thermal theories explaining combustion of gases to correlate parameters affecting ignition of dust dispersions. The dust dispersions were ignited in a Godbert-Greenwald furnace at atmospheric pressure. Ignition temperature and the concentrations of fuel, admixed inert powder, and atmospheric oxygen were related mathematically. Values for these parameters obtained in laboratory experiments for cornstarch agreed with theory. The developed equation permits extrapolation; the predicted upper igni-tion limits correspond with limited experimental data from laboratory and large-scale tests. Explanation of the effect of fineness of dust on ignition parameters is attempted by introducing a surface-area constant to modify the activation energy. Arguments are presented to show that the ignition process is a solid-gas phase reaction rather than an ignition of prevolatilized gases.

Jan 1, 1966

By Allen S. Smith

Analysis of the helium content of a natural gas presents more than the usual difficulties encountered in applying the thermal-conductivity method because of the relatively small amounts of this inert as present and the wide variation in the other constituents. However, the numerous advantages of this method and its adaptability to Continuously recording and control instruments make it worthy of consideration. A specific application of the method described yields quantitative results only when used with gas mixtures of known qualitative compositions which Vary within predetermined limits. Periodic analyses for the helium content of a producing gas well may be conveniently made by an absorption method, and a continuums analytical method is not necessary for this purpose. Natural gas containing 1.75 to 1.90 percent of helium produced from Government-owned wells is processed in the Amarillo (Texas) Helium Plant of the Bureau of lanes. The helium extracted in the plant is supplied to the Army and Navy, and the processed natural gas is sold to a commercial gas company. As complete recovery of the helium in the raw material is not economically practicable, the processed gas contains 0.1 to 0.3 percent of helium, depending upon conditions of operation. Production is checked against the helium removed from the gas, which before the installation of the thermal-conductivity apparatus was calculated from the analysis of a cumulative sample of the processed gas. As conditions of operation affect the residual helium content to a large extent, a composite sample was an uncertain index of the efficiency of the process.

Jan 1, 1934

By Ronald T. Mayerle

In-1992, the U.S. Bureau of Mines conducted a mineral investigation of the Anderson Mountain study area, including RARE II area 4-942, in Lemhi County, Idaho. The 7,340-ha study area lies within the Salmon National Forest about one kilometer north of the old mining town of Gibbonsville (pop.: 100). The eastern boundary of the study area is formed by the crest of the Bitterroot Range. The crest also serves as the continental Divide, and as the border between Idaho and Montana. The study area lies within the Gibbonsville Mining District, an important past producer of gold from lode and placer deposits. Since the 1870's, several hundred claims for both types have been located in the study area. Thirty-six current (1992) lode claims and two patented claim groups (one lode and one placer) are wholly or partially in the study area. No placer claims are current. In all, twenty-seven lode and five placer properties in and adjacent to the study area were investigated. Workings on the properties included 2 caved shafts; 36 caved adits; 8 open adits; 120 small pits, cuts, and trenches; and 4 large dozed cuts.

Jan 1, 1993

By Alla D. Mah

Heat content and entropy data at high temperatures were obtained for cuprous oxide (Cu2O) and cupric oxide (CuO). Experimental results and smooth values are reported. Equations are given for heat content increments and heat capacities above 2980 K. Low-temperature heat capacity data were obtained for cuprous oxide. Evaluation of the 2980 K entropy gave, S°298.15(Cu2O) = 22.08 ± 0.10 cal/deg mole. Heat of formation values were determined for cuprous and cupric oxides. The values are: AH°298.15(Cu2O) = -40,830 ± 300 cal/mole, and AH°298.15(CuO) = -37,230 ± 150 cal/mole.

Jan 1, 1967

By W. H. Oppelt

To provide a relatively structurally stable form of dried lump lignite, two North Dakota lignites from Mercer County were dried by the Fleissner process in an atmosphere of saturated steam at 200, 300, and 370 p.s.i.a. pressure, corresponding to steam temperatures of 382°, 417°, and 437° F., respectively. Two series of experiments were made at each test pressure with the individual lignites. In one series, the autoclave was preheated to the processing temperature before charging the lignite; in the other the lignite was charged into the autoclave at room temperature. In each case, heat losses were determined by blank tests of steam consumption over a similar operating cycle with the empty autoclave. The degree of moisture removal and net steam consumption were calculated from material balances. The amount of water removed as a liquid from the two North Dakota lignites during the heating and steaming periods was compared with results calculated from previously published data on drying Austrian lignite and Australian brown coal. These lignites, covering a wide geographical area, had original moisture contents ranging from 35 to 49 percent. The Austrian lignite and Australian brown coal are considered to be of Miocene Age, and the Dakota lignites belong to the Paleocene.

Jan 1, 1955

By M. M. Tilman

The Bureau of Mines conducted research to evaluate superplastic behavior in commercial magnesium-base alloys AZ6IA, ZK60A, ZW3, AZ3IB, ZWI, and an experimental Mg-12 pct Al alloy. Strain-rate sensitivity indices (m-values), maximum elongations, and effects of superplastic elongation on tensile properties were determined on fine-grained sheet. Inert-gas-pressure hemisphere-forming tests were conducted on selected sheet stock of the five alloys. Formability trials on AZ31B alloy sheet were conducted on industrial equipment for comparison with commercial superplastic forming of Zn-AI alloy. Closed-die-forming tests were performed on extruded ZK60A rod. All alloys exhibited well over 100-pct elongation, indicating superplasticity, at temperatures and strain rates near the maximum m-values. Tensile properties were generally reduced following 100-pct superplastic elongation, but not to an extent that would preclude use of the commercial alloys in the superplastically deformed condition. The potential for industrial superplastic forming of AZ31B sheet was indicated by hemisphere forming in the laboratory and substantiated in industrial forming trials.

Jan 1, 1982

By P. L. Loyselle, B. D. Comilsen, D. H. Carlson, J. H. Johnson

"In-mine airborne particulate samples have been successfully collected and the relative amounts of diesel and coal determined using the Laser Raman Quantitative Analysis (LRQA) method. This method allows analysis of filters which have been collected by a method similar to that used to determine the airborne respirable dust concentration in us underground coal mines. Samples were taken near the feeder-breaker, on haulage vehicles, and in the returns. Sampling methodologies were developed for coal-only and diesel-only particulate reference samples with sufficient filter loading for the LRQA method. A statistical analysis of reproducibility has been carried out. Samples have been collected simultaneously at two locations using the LRQA and the size-selective sampling methods. Good agreement between the two methods has been found.INTRODUCTIONThe goal of this research has been to develop the Laser Raman Quantitative Analysis (LRQA) method to measure the composition of respirable particulate, i.e. the fractions of coal and of diesel particulate, in the mine ambient air. In earlier Bureau of Mines sponsored research, we successfully demonstrated that the LRQA method could be used to measure the fraction of Diesel Particulate Matter (DPM) in coal/diesel particulate mixtures which were prepared in the laboratory.(I) 'The immediate objective was to test and refine this LRQA method on samples collected in a diesel underground coal mine.Specific objectives required to meet this goal include:I) Develop in-mine sample collection methods which will insure sufficient particulate loading on filters for LRQA. ,2) Develop methodology for in-mine collection of reference samples (""coal-only"" and ""diesel-only"" filters) which arc required for quantitative LRQA. 3) Analyze precision and accuracy of the LRQA method. 4) Compare composition measurements with another analytical method, i.e. the University of Minnesota/Bureau of Mines size selective sampling Micro-Orifice Uniform Deposit Impactor (MOUDI) method.An advantage of the LRQA method is that it allows analysis of filters which have been collected by a method similar to that used to determine the respirable dust concentration in US underground coal mines. No new sampling instruments and techniques are required. Transfer of sample from collection substrate to analysis substrate is not necessary. Furthermore, other analyses can be made on the same sample since the technique is nondestructive."

Jan 1, 1988

This report has been prepared in response to a request by the Bureau of Land Management (BLM) Fairbanks Alaska District Office that the Bureau of Mines quantitatively assess the potential supply of minerals from undiscovered deposits in the White Mountains National Recreation Area (WMNRA) and the western part of the North Steese National Conservation Area (SNCA) in Alaska. The assessment will be used to assist in future land-use decision-making. Resource Management Plans (RMPs) for the WMNRA and the SNCA were approved by the BLM in 1986. These plans imposed significant restrictions on new mineral development in the two areas. The level of public concern regarding these actions, especially on the part of the mining industry, has spurred BLM to seek additional information about the potential supply of minerals from the two areas with assistance from the Bureau of Mines. The assessment focuses on an area within the WMNRA and the SNCA which has been administratively closed to mineral entry. The study area encompassed approximately 1.24 million acres and included all of the WMNRA and the western portion of the North SNCA (fig. ES-1). Three quantitative estimates of the potential supply of minerals from the study area were developed: 1) For all lands in the study area, assuming that they are open to mineral entry-the baseline analysis; 2) For those lands which have been closed to mineral entry; and 3) For eleven prospective mineral activity areas, assuming that all are open to mineral entry.

Jan 1, 1989

By J. N. Greaves

Investigations were conducted by the U.S. Bureau of Mines to develop flowsheets for the recovery of tungsten and gold from four Alaskan scheelite-bearing ores. Basic gravity concentration and cyanide leach tests were performed on all samples. About 46 pct of the tungsten and 30 pct of the gold from one sample were recovered in a gravity concentrate containing 24 pet W03 (tungstic oxide) and 119 troy ounces per short ton (tr oz/st) Au. Froth flotation of the gravity concentrate resulted in separate tungsten and gold products with grades of 38 pct W03 and 2,720 tr oz/st Au and recoveries of 60 and 97 pet, respectively. Additional gold was recovered from the gravity and flotation tailings by cyanidation. Overall recoveries of tungsten and gold from this sample were 28 and 94 pet, respeetively. A flowsheet with mill design parameters was developed that consisted of (1) free gold and scheelite recovery by gravity methods and froth flotation and (2) fme-grained gold recovery by cyanide leaching of reground gravity and flotation tailings, followed by a carbon-in-pulp (CIP) circuit. Data were developed from the Bond mill work index, gold and tungsten flotation, conventional and high-rate thickening, cyanide leaching, and CIP adsorption tests.

Jan 1, 1989

By C. H. Elder

An analysis of the geologic structure of an area of Buchanan County, Va., was made by the Bureau of Mines using imagery from an airborne AN/APQ-97 side-looking radar system to evaluate that mapping technique for delineating structural features that may cause mining problems. Side-looking airborne radar (SLAR) was found to be a useful remote sensing tool for geologic structural analysis, Fault and joint systems identified by lineaments and linear patterns in the imagery were verified by surface and in-mine observations. Little Paw Paw fault was extended 10 miles by SLAR lineament analysis. A 22-mile fault, here named the Bishop-Bradshaw Creek fault, was mapped by lineament analysis and verified by observation of the fault on the Bishop Coal Co. mine map and on offset patterns of commercial gas production along the fault and surface observation of lineament along the fault. Three major super-imposed joint sets and several fault or fractured zones were identified by SLAR lineament analysis, showing more complex structure than earlier mapping indicated. SLAR imagery accurately delineated structural features that are known to affect gas migration and accumulation and that weaken the rock forming the immediate roof to mine workings, causing mining problems and potentially hazardous environment in the mines.

Jan 1, 1974

By Stephen D. Cramer

The objective of the present studies was to develop thick adherent and coherent coatings of platinum and palladium on refractory metals and other substrates of industrial and engineering importance. Existing platinum and palladium electrolytes were modified to make them suitable for the electrodeposition of thick deposits. The optimum operating conditions for these electrolytes were established. Pretreatment procedures for columbium, copper, graphite, molybdenum, nickel, stainless steel, tantalum, titanium, tungsten, vanadium, and zirconium substrates were studied. New pretreatment procedures for columbium, molybdenum, stainless steel, tantalum, tungsten, and nickel were developed. The internal stress and hardness of selected electrodeposits were measured. The effects of heat treatment upon the properties of electrodeposits were studied.

Jan 1, 1967