Search Documents

By Oliver C. Ralston

[This paper is an expanded revision of a report entitled "Froth Flotation and Agglomerate Tabling of Nonmetallic Minerals, " published in Transactions of the Canadian Institute of Mining and Metallurgy (vol. 40, November 1937, pp- 691-726) and prepared a year previously. Revisions embodied herein brine the data up to January 1, 1938. References have also been added to make the earlier paper more complete for the period it covered.]

Jan 1, 1938

By R. W. Van Dolah

An important function of stemming used to confine explosives in shot holes in underground coal mines is to minimize the chance of ignition of firedamp or coal dust by the detonation products. Until 1952, the Bureau of Mines approved only the use of fireclay or similar incombustible material for stemming permissible explosives. At least 2 feet of stemming were required except in holes less than 4 feet deep; in such short holes the stemming was required to be half the depth of the hole. Over the years, several special stemming devices have been proposed in the United States as substitutes for fireclay. Many economic and safety advantages were claimed for these devices, but only one approved device has been marketed in this country. Bureau requirements for stemming explosives in coal mines were modified at that time to permit the approved stemming device to be used as a substitute for the required fireclay.

Jan 1, 1961

By G. L. Oldright

The data presented in this paper were collected at the smelter of the Consolidated Mining & Smelting Co. of Canada, Ltd., Trail (Tadanac), British Columbia. Many thanks are due to S. G. Blaylock, vice president and general manager, James Buchanan, smelter superintendent, and George Murray, assistant smelter superintendent, for their broad general policy in permitting these data to be taken and published. life are also grateful for the help given by the staff members stated in Paper XI, Report of Investigations Acknowledgment is given several excerpts from experiments by F. E. Lee, head of the research staff. INTRODUCTION The past reputation of zinc as an ingredient in lead blast furnace slags has been bad. Zinc is thought of as a cause of accretions in the shaft of the blast furnace, of hot tops, of the formation of "zinc mush" in the crucible and forehearth, of lead-rich slags, of viscous slags, and. of low capacity in smelting.

Jan 1, 1934

By C. L. Klingman

In extracting helium from natural gas at Bureau of Mines helium plants, a continuous analysis of the helium content of inlet and outlet gas streams is required to determine extraction efficiency. An analyzer, using established principles of gas chromatography to effect the analysis, has been developed by the Bureau of Mines to meet this need. It will record the helium content of inlet or discharge gases from helium-extraction plants every five minutes, continuously, without the attendance of an operator. A 25-inch column of activated charcoal is used as a partitioning agent; nitrogen is the carrier gas; and a hot-wire, thermal-conductivity cell is the detector. A 1.0 mv, strip chart indicates the unbalance of the detector cell, Sample size is 0.37 cc, and carrier gas flow rate is 75 cc, per minute. Significant improvements in helium extraction have been demonstrated by using the chromatograph in three helium-extraction plants.

Jan 1, 1961

As a result of early experiments in underground mine illumination, the Bureau of Hines recognized the need for additional experience with the underground lighting of coal mines having low seam thicknesses. There was already experience with tile illumination of coal mines having higher coal seams, and this contract with Ocean Energy Inc. (OEI) was undertaken to contribute to the "low coal" experience. For the purpose of this contract, a "low coal? mine is defined as one having less than 45 inches of overall headroom in the working places. As a practical limit, 26 inches was the minimum coal seam thickness to be encountered in this program. In one instance, the maximum coal seam thickness was eight to ten feet, however, this particular work was at the direction of the Technical Project Officer (TPO) by virtue of the unique type of lighting arrangement that was to be evaluated which would be useful for low coal. At the outset of the contract, three major tasks were established. The first two tasks involved the installation of permissible fluorescent lighting equipment at two low coal mines. The intention was to illuminate mining sections in each case consisting of one or more machines. The third task was to illuminate a variety or mining equipment including a longwall. For the purpose of this report, the fol-owing identifies the particular installations associated with each task.

Jan 1, 1976

By Robert Blickensderfer

Tungsten alloys with high-temperature strength properties, comparable to the best of alloys recently developed by others, were produced by a new process called here the oxyreaction process. The process involved additions of a powder of a reactive metal compound, ZrN, ZrW2, or HfW2, to a base metal powder, tungsten, which contained some oxygen. The powders were blended, compacted, sintered, and extruded. During sintering, diffusion and internal oxidation occurred to produce reactive-metal oxide particles and solid solutions. A dispersion of oxide particles could be precipitated by heat treating. The oxyreaction process circumvents many of the agglomerating and coarsening problems encountered in the current methods for dispersing a stable oxide in a metal. Oxyreaction strengthening results from solid-solution strengthening and from dispersion strengthening produced by the reactive metal and its oxides. At a test temperature of 1,650° C, the alloys prepared from WW, had tensile strengths up to 70,000 psi and stress-rupture lives up to 142 hr at 10,000 psi stress; the alloys prepared from ZrN powders had tensile strengths up to 80,000 psi and stress-rupture lives up to 27 hr at 10,000 psi stress. Tensile strengthening in the alloys was attributed to Zr in solid solution or to Zr-O-W structures too small to be observed in an electron microscope replica. Stress-rupture life was attributed to a dispersion of submicron Zr02 particles which precipitated and grew to 0.05-to 0.2-micron size during the test. Tensile strengthening and stress-rupture life were dependent upon both the zirconium and oxygen contents with the maximum occurring at roughly 0.9 atomic pot Zr and 0.9 atomic pot 0. Studies of the details of the oxyreaction process were made on the W-ZrW2 alloys and three general steps were determined: (1) The reaction of 0 in tungsten powder with ZrW2 to form relatively large Zr02 particles; (2) the dissolution of remaining ZrW2 into the W matrix and partial internal oxidation to form ultrafine but sparse zirconium oxide particles and possibly to establish Zr-O-W structures; (3) the development of ultrafine Zr02 particles during high-temperature aging.

Jan 1, 1971

By Ruth F. Brinkley

This report is the 18th of a series of reports originally issued annually, and more recently bienially, to acquaint the public with the work of the Federal Bureau of Mines in explosives technology. Part I reviews briefly the overall activities during fiscal years 1957 and 1958.4/ Part II presents in abstract form the publications prepared by the Bureau that appeared during the period.5/

Jan 1, 1961

"Qatar, crude petroleum, production, annualdata MY 1949-51Quality mine, Ark., coal, carbonizing properties TP 667washabilty study RI 496N. Dak., lignite, grindabilty as function ofmoisture, tests, results RI 5167"

Jan 1, 1960

By Michael S. Miller

In 1987, 1988 and 1989, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the Sperry Creek Wilderness Study Area (OR-003-035; 5,600 acres) and the Gold Creek Wilderness Study Area (OR-003-033; 13,600 acres), plus an additional area (OR-003-033; 2,180 acres) adjacent to the Gold Creek Wilderness Study Area. The wilderness study areas and the addition are south of the Malheur River and are about 20 miles east of Juntura, Oregon. The wilderness study areas and the addition are underlain by volcanic rocks, predominantly basalt and rhyolite flows, breccias, and welded ash-flow tuffs. Lacustrine deposits containing diatomites occur mainly at the east side of the Gold Creek Wilderness Study Area and addition. Alluvium lies along the Malheur River, in terraces and fans south of the Malheur River, and along the floors of some creeks. Shear zones and faults have offset the rocks and provided channels for eruption of volcanic rocks and epithermal mineralization by hot springs.

Jan 1, 1989

By Merle L. Bowser

An alinement (steering) sensor for continuous mining machines has been developed under a Bureau of Mines contract. A laser source in the entry projects a beam parallel to the centerline of the entry. The beam is optically shaped to a narrow, vertical fan and illuminates an array of optical sensors bunted on the mini machine. These sensors interpret the location of the beam into meter readings of heading (angle) error and lateral displacement errors. The system, which was tested for 5 months in an operating mine, appears to be fundamentally sound, and with some modification, should be applicable to remote or automatic guidance of continuous miners and other machines.

Jan 1, 1976

By Richard A. Dick

In this report commercial blasting compounds are classified according to their nitroglycerin (or equivalent explosive oil) and ammonium nitrate content as dynamites, gelatins, blasting agents, military explosives, and blasting , accessories. The ingredients and more significant properties of each explosive are tabulated and briefly discussed. Data are summarized from various handbooks, textbooks, and manufacturers' technical data sheets, together with the author's personal experience; however, this report is not intended to be a technical handbook, since it does not deal with blasting techniques. Instead, it seeks to acquaint the reader with the great variety of explosives, available, their advantages and disadvantages, and their general areas of application. Properties discussed are weight strength, cartridge strength, detonation velocity, density, detonation pressure, water resistance, and fume class. The weakness of the strength rating system and the importance of detonation pres- , sure, density, and detonation velocity in rating explosives are discussed. The terms "blasting agent" and "slurry," which are often misused, are defined. Trends indicate that blasting agents (that is, blasting mixtures with none of of the ingredients singly classified as an explosive), particularly high-density slurry blasting agents, will dominate the explosives field in the future.

Jan 1, 1968

By C. P. Fang

"For lower stages of multinozzle micro-orifice impactors, as many as two thousand nozzles are uniformly arranged within a cluster diameter of 1.06 inches. In the impaction region the mass flowrate of the spent air increases along the radius and reaches a maximum at the periphery. This crossflow can significantly deflect the air jets of the outer nozzles, hence the characteristics of impaction changes.Investigators in heat transfer and fluid mechanics have studied the influence of crossflow on jet deflection and found the dimensionless deflection of the jet centerline X/Dn is a function of (S/Dn)(l/m) . only, here X is downstream coordinate measured from the center of the jet orifice, Sis the jet-to-plate distance, Dn is the orifice diameter and m is the jet/crossflow mass flux ratio defined as:"

Jan 1, 1989

By Ted C. Briggs

The Bureau of Mines is evaluating the thermodynamic properties of helium and helium-containing mixtures. Twenty-two compressibility runs were made with helium at 0° C and pressures to 800 atmospheres using a Burnett-type apparatus. Data from the 22 runs were treated simultaneously and as separate runs while different functional forms and weighting factors were used. A fourth-degree-polynomial equation in the pressure gives a statistically satisfactory representation of the compressibility factor when the data are treated simultaneously and a weighting factor of Pr-3/4 is used. The second virial coefficient of helium at 0° C from this investigation is 11.997±0.015 cm3 mole-1. The stated uncertainty is the random error standard deviation. Compressibility factors determined by this investigation are precise to better than 0.01 percent and are believed to be accurate to better than 0.02 percent.

Jan 1, 1969

By Foster Fraas

The dielectric constant .has been frequently referred to as an important property in electrostatic separation whore the particles are in an air ambient. Hatfield (1) has studied the problem on the basis of fundamental theory, with the conclusion that separations in air dependent on the differences in dielectric constant, in conjunction with a nonhomogeneous field, are not feasible, because of the low dielectric strength of the air. Although Hatfield has made the statement without showing the calculation or data, calculated values substantiating this under certain conditions of the problem will be given in the following text. However, under other Conditions, these conclusions do not hold, and it is probable that the dielectric constant is indirectly influential.

Jan 1, 1948

By Raymond L. Lowrie

Coal deposits in the Boulder-Weld County coalfield in Colorado are analyzed in relation to economic factors governing the growth, stability, and competitive potential of the coal industry. Recoverable reserves, estimated to be 571 million tons, are discussed in detail, particularly those in the Erie and Frederick Quadrangles. Geology of the coal measures, quantity and quality of water resources, and chemical and physical properties of the coal are described. Coal production factors, including mining techniques and equipment, labor requirements, transportation facilities and rates, and markets, are considered for coal's position in competition with alternate fuels. Growth of the fuels market, through increasing thermal-electric power generation in the Denver Metropolitan Area, will stimulate coal production in Colorado. Reserves of the contiguous Boulder-Weld coalfield, if mined in a sustained, year-round, high-tonnage operation, could be used to supply much of that fuel demand.

Jan 1, 1966

By Joe H. Skidmore

This paper, describing mining and milling methods and costs at the Gold Hill mine, is one of a series being published by the Bureau of Mines. Boise Basin, in which the geld Hill mine is located, is in the central part of Boise County, Idaho, about 30 miles by air line northeast of Boise. The mine, owned and operated by Talache Mines, Inc., is at the southern end of the town of Quartzburg. About 115 to 125 tons daily is mind by square-setting and is treated in an amalgamation plant.

Jan 1, 1938

Volumetric measures [ ]

Jan 1, 1958

By Robert F. Chaiken, Thomas H. Dubaniewicz, Gregory M. Green, Kenneth L. Cashdollar

Optical technologies have progressed rapidly in the past 15 years. One application of laser technology in underground coal mines currently under evaluation is the remote measurement of explosive methane gas. Federal regulations require that atmospheric monitoring systems used in gassy underground mines where permissible equipment is required shall be intrinsically safe. Mine Safety and Health Administration criteria for the evaluation and testing of intrinsically safe apparatus and associated apparatus contain no specific guidance for optoelectronic components such as diode lasers. The National Institute for Occupational Safety and Health is conducting a study to help provide a scientific basis for developing appropriate safety guidelines for optical equipment in under- ground coal mines. Results of experiments involving ignition of methane-air mixtures by collections of small heated particles of Pittsburgh seam coal and black iron oxide are reported. The inert but more strongly absorbing iron oxide targets consistently ignited methane-air mixtures at lower powers than the coal targets. Minimum observed igniting powers for laser energy delivered by 200, 400 and 800 pm core fiber optic cables and directed onto iron oxide targets in methane-air atmospheres were 0.6, 1.1, and 2.2 W, respectively. Comparisons with the results of other researchers are made. A thermal layer theoretical approach to describing the process is included as an appendix.

By Rov G. Stott

In recent years there has been no loss of life from fires in the underground mines of the Lake Superior district, but numerous minor fires and several serious ones involving loss of property and production have occurred. The iron-ore-producing companies recognize that well-equipped mine rescue stations are a valuable asset against the ever-present ranger of mine fires or the possibility of hazardous atmospheric conditions underground. Prompt action by trained and properly equipped rescue teams is recognized as the prime essential in saving lives, property, and production when fires occur. To achieve this purpose, the mining companies have provided themselves with mine rescue equipment and maintain trained mine rescue crews. This circular describes how one progressive company has provided, maintained, and improved upon such protection for its underground iron-ore mines on the Marquette and Menominee iron ranges of Michigan's upper peninsula. SUMMARY The central mine rescue station of The Cleveland-Cliffs Iron Co. at Negaunee, Mich., has provided the company's mines with competent and well-equipped mine rescue teams. The new central mine rescue station at the Mather mine "B" shaft has the distinction of having underground training facilities provided as a part of the station. The company maintains the largest trained force in mine rescue in the Lake Superior district, and mine rescue training is employed as a part of the accident-and fire-prevention program. One of the most important results has been the promotion of closer cooperation and understanding between the management and the workmen. In addition to the service rendered to company mines, the station and its personnel have given assistance to others. The station and its equipment have also been used for training several nearby community volunteer fire departments. This mine rescue station and its personnel have been a dependable and valuable asset to the community in which it is located.

Jan 1, 1954

By Z. T. Bieniawski, R. K. Zipf

"Zipf Jr., R.K. and Bieniawski; Z.T., 1989. A fundamental study of respirable dust generation in coal. Min. Sci. Technol., 9: 87-99Black lung disease in coal miners induced by the formation of fine fragments of coal imposes very high human and direct costs. A fundamental understanding of the fracture processes leading to fine-fragment formation in coal by applying principles of fracture mechanics is presented. A four-step hypothesis is proposed which sequentially describes the mechanics of fine-fragment formation during a generic coal material—coal cutting tool interaction. These steps include: (1) development of a crush zone under the tool tip, (2) macrocrack propagation. (3) shear movement along macrocracks, and (4) additional fragmentation from shear. This model contains two sources of fine fragments, namely crushing under the tool tip and shearing along the macrocrack surfaces. Three critical assumptions are made that require experimentation. First, the coal material must contain flaws of sufficient density and sufficiently small size to liberate fine fragments by crushing. The following conceptual relationships are proposed between flaw size, spacing and fragmentation: first, the active flaw size must be less than the desired particle size and second, the spacing (or density) must be in the order of the particle size. The second major assumption is that a mixed mode fracture theory will describe the initiation and crack growth direction for the microscopic inherent flaws. The third assumption is that some degree of roughness damage, and interlocking exist along the newly formed macrocrack surfaces such that a small amount of shear movement along that surface leads to additional particle formation at a microscopic scale. Preliminary analysis of the mechanical regime under a cutting tool tip places order of magnitude bounds on the stresses strains, cycle time, stress rates and strain rates. Even though the tool moves and loads the coal material with considerable speed, a quasi-static stress analysis is applicable in this region.Introduction.The generation of fine fragments (respirable dust) during various coal mining processes may lead to the incidence of coal workers pneumoconiosis (black lung disease). The human and direct cost of dust-induced illnesses in coal miners is very large. By several. accounts [1,2] the Federal Government paid out about $12 billion to almost 500,000 coal miners and their beneficiaries between 1970 and 1980. In addition, several states and many coal operators have established their own compensation programs at costs ranging from a few cents to several dollars per ton of coal mined [2]. Since 1980, 'the present liability of the Federal disability trust fund has approached $20 billion and the benefit payments exceed $1 billion per year. There .are also hidden costs due to dust, in the form of increased equipment wear and decreased operator productivity, both of which are due to the poor operating environment. Quantifying these costs may be difficult; however, they may be in the same range as the present pneumoconiosis costs. These high human and direct dollar costs may be prevented or reduced through long term research efforts directed at understanding the generation and control of respirable dust and the incidence of black lung disease."

Jan 1, 1989