Search Documents

By M. S. Seehra, R. S. Pandurangi

"Investigations of the infrared spectra of crystalline and amorphous silica particles of different sizes (0.05, 5, 10, 15, 30, 45, and 260 um) in the range of 400-4000 cm-1 using Fourier transform infrared/photoacoustic spectroscopy we reported. The change in the intensity I of the signal with porosity e of powders follows the e/(1 - e) dependence for strong bands and e dependence for weaker bands as pre¬dicted by the theory of McGovern of al. For strong bands, I also follows the empirical relation I ~ D-n, where D Is the particle diameter in cm and n = 0.34-0.42. The anomalous positive frequency dependence of I on the modulation fre¬quency f observed for the stronger bands in the 45-pm and 260-pm particles Is believed to result from saturation. Some observations on the effect of changing the background from (carbon black) powder to pellet are also made.INTRODUCTIONSince the publication of the Rosencwaig—Gersho (RG) theory on the photoacoustic effect in solids (1, 2), Fourier transform infrared/photoacoustic spectroscopy (FTIR/PAS) has become an important technique for obtaining the IR spectra of surfaces and materials in their natural state (1-12). In the one-dimensional RG theory, the incident radiation, modulated at frequency f, is absorbed by the material to a depth pp = 1/B (B = absorption coefficient), thus setting up temperature variations in the material. These variations heat the adjacent gas/solid interface leading to the pressure fluctuations of the gas above the sample, which in turn is detected by microphone as a PA signal. The thermal wave originating from no deeper than the thermal diffusion length(2k/npcf) 1/2 in the material contributes to the PA signal (here k, p, and c are respectively the thermal conductivity, density, and specific heat of the material). Since u2, can be varied by varying the experimental parameter f, depth pro¬filing by PAS is possible and a number of papers on this subject have appeared in recent years (2-10). Another im¬portant phenomenon is saturation which occurs when the material thickness 1> u> us (1-12).The original promise of PAS for use with powder samples, without the need to ""prepare"" samples as in FTIR spectros-copy, has not yet been fully realized because of several com¬plications. Theoretical works by Monchalin et al. (13) and McGovern et al (14) showed that the interstial gas in the voids of the powders can act as amplifier and that, for the same mass, a finer powder is expected to yield higher PA signal than a coarser powder. Although in a number of earlier studies (15-21) an increase of PA signal with decreasing particle size has been observed, a quantitative check on the equations developed by McGovern et al. (14) has not yet been made. It is necessary to understand the particle size effects in PAS if the promise of PAS for IR spectroscopy of powders is to be realized. In this paper, we report results of a detailed study on the PAS of silica powders for the particle size range of 0.05-260 um and compare the results with theory (14). We have also investigated the frequency dependence of the variousIR modes in these powders and show that the saturation phenomenon affects at least some of the observations. Some observations on the effects of pellet vs powder background are also reported (22-24). Details of these findings are presented and discussed in this paper."

Jan 1, 1990

By J. E. Tress

The Bureau of Mines has developed a process to utilize waste heat from electric arc steelmaking furnace gases to preheat the ferrous material charged to the furnace. Four heat exchangers were designed, tested, and operated successfully on 1-ton electric arc furnaces. Briquets and pellets were charged continuously, both countercurrent to the hot furnace offgasses and at ambient temperatures. A comparison of the electrical energy consumed in each situation showed that preheating can lower energy requirements as much as 15.6 percent.

Jan 1, 1975

By W. Wan, R. V. Ramani, J. M. Mutmansky

"Diesel particulate matter (DPM) emitted from diesel engines is currently considered to be a health problem in underground mines. As a result, attempts have been made to control DPM both by reducing emission rates and by managing the DPM that gets into the mine atmosphere. This paper presents a method for modeling the generation, transfer, and distribution of DPM in coal mining sections through the use of a convection-based computer model so that controls for emitted DPM can be evaluated. A variety of ventilation strategies and diesel deployment schemes for room-and-pillar development sections were simulated to compare their effects on average DPM concentrations at several fixed and mobile personnel locations in the section. Input data for the model was gathered from actual diesel development sections and derived from experimental study results provided by other researchers. Analyzed using the model were ventilation schemes using vent tubing and brattice, exhaust location strategies on the vehicles, and the direction of ventilation at the feeder-breaker location. A summary of results from this study is presented.With diesel equipment holding an important place in underground coal mining and growing in use over time, it is important to develop and improve controls of the exhaust emissions, especially diesel particulate matter (DPM), to further reduce potential health hazards. The proper design and maintenance of diesel engines and on¬board control procedures are paramount requirements for controlling DPM successfully. There is also, however, a significant reduction potential in terms of personal exposure that can be realized by managing the DPM that gets into the airstream. Strategic design of the mining, ventilation, and equipment implementation systems remain essential for efficiently reducing the DPM concentrations.Modeling the effect of diesel exhaust contaminants upon the mine atmospheric quality will permit improved health and safety design of the overall mining and ventilation systems. Numerous studies have been performed to model the distribution/transport of gaseous and particulate emissions in the underground mine atmosphere and some very sophisticated convection/diffusion models have been developed (Skobunov, 1974; Thakur, 1974; Stefanko and Ramani, 1975; Wala, 1980; Bandopadhyay and Ramani, 1983). Most of these models were developed for a single airway or based on the assumption that the ventilation network of a mining section can be approximately represented by a single intake and a single return. The complexity of most models of the convection/diffusion type and the mobility aspect of diesel haulage units made a detailed emissions model very difficult to develop.The current model is an attempt to fill the need for a more generic tool applicable to mining sections employing multiple mobile diesel units by simplifying the convection-diffusion model to a convection-only model. The simplification is based on the fact that the diffusion coefficient will affect only the transient environmental contaminant concentrations with little or no affect on the time-weighted-average concentrations over a relatively long period such as a working shift (Lee et al., 1994). In view of the difficulties involved in mathematical modeling, the approach here is developing and using a computer simulation model. A PC-based FORTRAN 77 simulation model for the analysis of mining systems with multiple diesel sources and any ventilation network configuration was developed to study the distribution/transport of DPM in mine airways, evaluate methods of reducing DPM concentrations, and explore modifications to existing mining practice."

Dec 1, 1996

By Felix A. Vogel

Rutile concentrate, used in the manufacture of welding rode, smoke-screen chemicals, and alloys, is being produced by the Titanium Alloy Co. of Arkansas at its mine and. mill in Magnet Cove. The company estimates a substantial reserve of recoverable rutile. This is a new operation, and production figures are not known. Previous operations had stripped the placer material, leaving the underlying mineralized zone. INTRODUCTION This report describes the mining and milling; operations of the Titanium Alloy Co. of Arkansas. The property was examined by the author on March 4, 1942, and subsequent dates. J. A. Wood, general manager, was very helpful in supplying information.

Jan 1, 1944

By John B. Shutack

In an effort to improve the performance of the explosive-anchored rock bolt, the Bureau of Mines studied the effect of the detonation velocity of the explosive and type of charge (linear or nonlinear) on the fracturing tendency of the anchor tube. Also, different types of tubing were compared to determine the one most suitable for use as an anchor tube. The Bruceton up-and-down method was applied in tests in which steel shooting blocks having boreholes ranging from 1-3/8 to 2-1/8 inches in diameter were used. Of the four types of tubing evaluated, a welded A-178 tubing that was drawn over a mandrel and renormalized gave the most promising results. The A-179 seamless tubing that is normally used with the explosive bolt was the most inferior. Both types, however, gave significantly better anchorage than the conventional shell when tested in both laboratory and underground experiments. Within the range of velocities studied (5,000 to 7,000 m/sec), the type of explosive showed no significant effect on anchor-tube performance. In general; linear explosive charges provided better anchorage than nonlinear charges.

Jan 1, 1968

By Janke L. W. Jolly

Owing to an upsurge in export earnings. Cameroon made substantial economic Progress in 1978 and 1979. With a real growth estimated at 6%, the gross domestic product (GDP) for 1979 surpassed $5 billion.2 Crude petroleum production was providing a new potential in 1978 and 1979 for achieving national self-sufficiency. Among other benefits, crude petroleum exports were helping to offset the escalating costs of refined petroleum imports and to reduce the 14% to 17% annual rate of inflation. Over the 4 years prior to 1978, Cameroon's petroleum imports increased by 12.1% in volume annually, while the import cost increased by 24.5% annually to about $105 million. Total export earnings for 1978 were $805 million,3 to which crude petroleum contributed $25.3 million and crude aluminum product exports contributed $25.9 million. Petroleum exports had increased to about $240 million in 1979 and were in third place after coffee and cacao. Total imports for 1978 were valued at nearly $1 billion. The volume of petroleum imports decreased in 1979 to 552,000 tons, compared with 622,000 tons in 1978. The European Economic Community (EEC) countries purchased over 75% of total Cameroonian exports and provided most of the Nation's imports. The United States purchased $12.4 million in petroleum exports from Cameroon in 1978. Domestic consumption of aluminum metal from imported Guinean alumina continued. to grow; thus exports of this metal to France (valued at $2 million in 1978) and Japan

Jan 1, 1981

By Parry. V. F., W. S. Landers

"INTRODUCTION Approximately 1,250,000 tons of 2-1/2-inch and 1-1/2-inch slack, representing over half of the output from 40 to 50 mines, is produced in the Denver region each year. Part of this slack is made by crushing lump, and some of it is rescreened to make pea and modified pea sizes measuring 1-1/2 inches by 2-1/2 inches and 3/4-inch by 1-1/2 inches, round-hole. Modified pea is popular as domestic stoker fuel. Approximately 900,000 tons of slack 0 by 2-1/2 inches, 0 by 1-1/ 2 inches, and 0 by 3/4-inch in size are consumed by industrial plants, the principal consumers being a large power plant and the beet-sugar industry. The power plant uses annually 250,000 to 275,000 tons of pulverized fuel and can pulverize slack of any size, while the sugar factories consume about the same quantity of coal in stokers. The sugar factories store about 110,000 tons of 2-1/2-inch slack under water from January to October, and burn the remainder of their consumption directly during the campaign season from October to December. For this purpose, sugar-factory power plants can use any size of slack, which is recrushed to pass a 3/4- or 1/2-inch screen before burning on chain-grate stokers. About one-third of the 2-1/ 2- inch slack produced in the field is used in smaller industrial plants that employ stokers.Certain factors affect the utilization of 2-1/2-inch slack in the Denver region. The increasing production of hydroelectric power has reduced the consumption of coal at power plants slightly. If more hydropower is generated, the trend of consumption of slack might be downward, unless industrial activity offsets this greater output. Rapid increase in number of domestic stokers during recent years has necessitated preparation of greater quantities of stoker coal, with the result that more lump is crushed, and preparation facilities are changed. At present about 19 percent of the coal produced is crushed to meet the constant demand for industrial fuel as well as the increasing but variable demand for the small domestic stoker sizes. The quantity crushed has increased 12 percent during the last 6 years. These factors are shifting constantly. The trend toward the use of clean and smaller sizes for domestic stokers gives a slack having a larger proportion of fines. In future, even greater quantities of small stoker coal probably will be prepared, and the resulting greater quantities of small slack will have to be used for industrial purposes."

Aug 1, 1942

By Oliver Bowles

Whiting or Paris white is a fine-grained preparation of calcium carbonate having a wide variety of uses. Until recent years it was prepared almost exclusively from certain north European chalks. With the curtailment of imports of European chalk during the World War of 1914-18, however, finely ground limestone, of domestic origin was used more extensively to satisfy the American demand.

Jan 1, 1942

By W. A. Stickney

This report summarizes the results of laboratory tests of five samples of low-grade phosphate ores from Idaho. The laboratory test work has demonstrated that by grinding, desliming, and flotation a portion of the siliceous gangue can be removed. The highly carbonaceous ores responded successfully to treatment after preroasting, to produce a plus-30-percent-P205 product. It has been found that highly siliceous ores, as represented by the samples treated, are more readily amenable to concentration than ores high in calcium carbonate. Of the five samples tested, four were amenable to concentration to a product containing over 30 percent P205. One sample, from the Conda, second bed, was not amenable to mineral-dressing treatment to produce a plus-25-percent-P205 product.

Jan 1, 1955

By J. W. Eckerd

This report describes an investigation of the technical feasibility of using a conventional commercial-size (10-ft. i.d.), rotating grate, dry-ash-removal type gas producer to make producer gas from chestnut-size bone anthracite. Test instruments were installed, and some minor changes were made in the equipment to handle the large quantities of materials expected. Extensive tests, lasting about 4 weeks, were planned, using 35 to 50 percent ash chestnut anthracite bone. However, operations were suspended after 8 days when it became apparent that to use this type of fuel satisfactorily substantial changes in equipment and operating procedures would be required. Nevertheless, enough data were obtained to indicate that gas could be produced continuously and routinely from bone coal in this type of producer whenever conditions justified the necessary development work.

Jan 1, 1960

By S. B. Bealko

Mining haul trucks comprise the majority of the equipment used in underground limestone mining operations and are known to emit high levels of noise. A previous study conducted by the National Institute for Occupational Safety and Health (NIOSH) indicates that 70-90 percent of all miners have a noise-induced hearing loss (NIHL) great enough to be classified as a hearing disability by retirement age. These results demonstrate the public health need to protect the hearing of workers in the mining industry, including haul truck drivers. Cab enclosures present an opportunity to isolate the haul truck operator from both truck and other noise in the mining environment. A total of twenty-five haul truck cabs were studied which were divided into three style (treatment) categories determined by soundproofing features and technology for noise reduction: old-, new-, and retrofitted-style. This study examines the contribution of cab acoustics, operator performance, and maintenance to noise reduction for each cab style. Dosimeters were used to measure 8-hr time weighted average sound pressure levels (TWA8 SPLs) inside and outside the cabs to determine if different acoustical treatments affect cab attenuation. Adherence to the Mine Safety and Health Administration (MSHA) Permissible Exposure Limit (PEL) of 90 dB TWA8 (with a 90 dB threshold) was used as the main indicator of overall noise reduction achieved. Dosimetery results indicate only 2% of the samples exceeded the PEL, but samples could still be reduced much further. Descriptive and comparative statistics indicate that noise levels inside the new-style cabs are significantly lower than the other two cab styles. Also, data suggest that there is no difference in noise exposures when comparing the old-style to retrofitted cab styles. Operator influence (opening doors and windows) was a significant factor for increasing noise exposure. This paper demonstrates that properly designed cabs can achieve major noise reductions, but noise levels could still be reduced much further below the MSHA PEL. New-style cabs, equipped with modern noise-reduction treatments, exhibit much lower noise exposures than the other two cabs styles, and the effectiveness of the current noise-reduction treatments for retrofitted cabs is questionable. Haul truck driver observations indicate that improved noise exposure reduction training is needed. Finally, specific targets for future noise reduction research are suggested that will further contribute to the prevention of hearing loss for haul truck operators.

By M. L. Skow

Large tonnages of the manganese ores found in Aroostook County, Maine, are refractory to conventional mineral-dressing techniques and to the common chemical- extraction procedures. The Maple Mountain-Hovey Mountain ores are typical of this type. Because the most promising method of recovering the manganese from these ores has been a chloridizing roast in which the ground ore is in contact with gaseous hydrogen chloride, preliminary batch tests were made with a fluidized bed. On the basis of these tests, it was concluded that fluidization, with careful control of operating conditions, could be employed for this cloridization and warrants further study. Selective volatilization of the iron at 600° C. was unsuccessful. An operating temperature of approximately 950° C. was necessary for a practicable rate of volatilization of manganese chloride. Hydrogen chloride contents of 10 to 100 percent of the fluidized gas gave essentially equivalent manganese recoveries with an 80- minute retention time, For shorter periods reaction was more complete with the higher hydrogen chloride concentrations. At the 80-minute retention period the lower hydrogen chloride concentrations volatilized somewhat less iron and also improved the physical operation of the process. Fluidization gave results superior to comparable tests on chloridization in a fixed bed.

Jan 1, 1956

By J. L. Stauffer, L. J. Gaydos, L. M. Demers, D. C. Kuhn

"Eicosanoids and cytokines produced by alveolar macrophages (AM) are key mediators of pulmonary inflammation and fibrosis. In order to determine if eicosanoid production and cytokine production are altered in AM obtained from coal miners, we compared production of prostaglandin E2 (PCE2), thromboxane A2 (TXA2), leukotriene B4 (LTB4), interleukin-1 beta (IL-1B ), and tumor necrosis factor alpha (TNfa.) by cultured AM from normal human subjects and coal miners. The recovery of AM from miners' lungs by bronchoalveolar lavage was significantly greater than that from control subjects. Mean eicosanoid and cytokine production by AM from active miners was also increased compared to AM from control subjects, but this increase was not statistically significant. AM from control subjects produced significantly more TXA2 and TNFa. when exposed to lipopolysaccharide than did AM from miners. The cyclooxygenase inhibitor suprofen reduced PGE1 and TXA1 production and TNF0t. release but had no effect on LTB4 production or IL-1B release by miners' AM. The lipoxygenase inhibitor nordihydroguaiaretic acid attenuated TNFa release, as well as that of LTB4, but had no effect on IL-1B release. Inhibition of thromboxane synthase by UK 38,485 also reduced TNFa release by active miners ' AM but had no effect on PGE1, LTB, production, or IL-1 f3 release. The results of these studies suggest that occupational inhalation of coal dust may increase total lung eicosanoid and cytokine levels and reduce the reactivity of AM to bacterial endotoxin. Furthermore, coal dust-induced changes in both eicosanoid and cytokine release may be subject to pharmacological modulation.The alveolar macrophage (AM) is a primary defensive cell in the lung and is one of the first cell types to encounter inhaled mineral dust. The response of the AM to invading foreign material is designed to enhance the defensive capacity of the lung. However, in the case of occupational inhalation of mineral dust particles, this response may be inappropriate, resulting not in the defense of the lung but in chronic inflammation and fibrosis (Rom et al., 1987; Takemura et al., 1989). The reaction of the AM to chronic mineral dust exposure may involve the exaggerated release of paracrine mediators of lung function, including eicosanoids (oxygenated derivatives of arachidonic acid) and peptides, including cytokines and growth factors (Sibille & Reynolds, 1990). Eicosanoids are involved in bronchial and vascular smooth muscle reactivity, vascular permeability, fibroblast growth, and the recruitment of additional immune cells to the alveolar space (Barnard et al., 1992; Elias et al., 1985; Scott et al., 1982). AM-derived cytokines such as interleukin-1 beta (IL-1 B) and tumor necrosis factor alpha (TN Fa) have a variety of biological activities including the regulation of fibroblast growth and proliferation (Becker et al., 1989; Libby et al., 1989; Schmidt et al., 1984). Interestingly, in vitro studies with macrophages suggest that the production of cytokines may be linked to eicosanoid production, in particular that prostaglandin E2 (PGE2) may down-regulate IL-1 f3 and TN Foe production by the AM (Bonta et al., 1989; Kunkel et al., 1986; Monick et al., 1987)."

Dec 1, 1996

Maps To Accompany Bulletin 507

Jan 1, 1952

By J. Torma-Krajewski, C. Hipes

Although many mining companies apply ergonomic principles, it is usually done either informally and/or reactively. An example of an informal approach is replacing worn equipment (such as seats) with models that have ergonomic features. Another example is modifying a task to eliminate safety hazards. Such approaches reduce risk-factor exposures that can lead to musculoskeletal disorders (MSDs). A reactive approach is followed when modifying a task/ equipment after an MSD occurs. However, neither of these approaches involves a systematic method of proactively applying ergonomic principles to actually prevent injuries or illnesses. This paper discusses how Vulcan Materials Company applied ergonomic principles and implemented interventions to reduce risk-factor exposures.

By N. Fragen, H. H. Stroch

"INTRODUCTION A previous paper by H. H. Storch 4 described. three processes for the production of potassium sulphate from polyhalite (K2S01.MgSO1.2CaS04.2H2o), Since these processes depended upon calcination of polyhalite followed by leaching with water at 100°C., the fundamental reactions occurring in these steps were discussed in detail. This paper, which describes processes producing syngenite (K2S04.CaSO4.H2O) and potassium sulphate and gives data concerning the production of by-product magnesia, presents the results of work performed at the Non metallic Minerals Experiment Station of the U. S. Bureau of Mines, maintained at New Brunswick, N. J., in cooperation with Rutgers University.A study of the solubility relationships of the system 5 Ca++ -Mg++ -K+-SO4 = H20 at 25ºC. shows that syngenite is stable in the presence of a concentrated MgSO4 solution, the K2SO : equilibrium concentration being comparatively low (2.6 per cent), The processes described below, which involve the conversion of calcined polyhalite to syngenite, are based on the 25°C. equilibria. It has further been found that syngenite can be decomposed by water at 100ºC, yielding a 9 to 10 per cent K250 solution, the solid phase being potassium calcium pentasulphate (K2SO, 3CaSO.H2O, hereafter referred to as ""pentasulphate""). This latter compound is unstable in the presence of water at 25°C., its decomposition resulting in a solution containing about 3 per cent of K2SO4 and a solid phase consisting of gypsum. This behaviour of syngenite with water at 100°C. and of pentasulphate with water at 25ºC. constitutes the basis of processes for the production of K2SO4 by way of the conversion of calcined polyhalite to syngenite,Syngenite is a product which may be used as a fertilizer per se. As produced in the process to be described, it contains about 50 per cent of K2SO1, and will readily give up its potash content on treatment with water, although the limiting concentration at ordinary temperatures is approximately 3 per cent. This definite but limited solubility should make this product more desirable as a fertilizer then the more concentrated forms of potash salts which have higher solubilities and hence involve the danger or plant injury due to a high local concentration of potash."

Sep 1, 1931

By R. D. Van Zant

The method for smelting zinc in horizontal retorts developed several centuries ago is still in use. This process consists essentially of the reduction of zinc oxide by carbon at 1,200° to 1,400° C. in a fire-clay retort. The reaction is highly endothermic, and a high radiation loss occurs in transferring the heat of reaction through the fire-clay walls. In recent years, silicon carbide retorts with much better heat-transfer characteristics than fire clay have been supplanting the old retorts. The practical impossibility of recovering the carbon monoxide formed in the reduction causes a large loss of fuel. Intermittent smelting is done in small retorts that are manually charged and discharged, and the furnace crews must be specially trained if efficient results are to be obtained. During the past 20 years several processes have been introduced that have substantially improved the horizontal-retort process. One of these, developed by the New Jersey Zinc Co., consists of a continuous process in which a briquetted mixture of zinc sinter, reducing agent, and binder is coked at 750° to 900° C. and charged into a vertical silicon carbide retort. A supply of displacement air or exhaust combustion gas is introduced at the base of the retort at an appropriate pressure in order to keep the zinc vapor from condensing on the cooled residue in the lower part of the retort. Any .oxidizing constituents in the displacement gas are converted to carbon monoxide by reaction with the carbon in the charge. The spent residue is continuously removed at the bottom of tl1e retort. The chief advantages of this process are said to be increased output per man-day, improved working conditions, high recovery of zinc, increased thermal efficiency, and long retort life.

Jan 1, 1950

It is a pleasure to submit to the National Critical Materials Council (Council) some of my thoughts concerning the important tasks which lie before you. It long has been my belief that America's economic health and national security may depend to a substantial degree on whether we have available to us an adequate supply of critical and strategic materials at reasonable cost. To the extent the Council can contribute to the identification and implementation of wise public policies which facilitate the achievement of that goal, we and our children should be grateful. Even before assuming office, President Reagan warned of the danger of undue dependence on imported materials essential to the Nation's defense and economic well-being. After his election, he appointed a transition task force on strategic and critical materials, and he later directed the Cabinet Council on Natural Resources and Environment to prepare .a National Materials and Minerals Program Plan and Report to Congress, which he forwarded to the Congress in April 1982. In 1984, my predecessor, Secretary Clark, established the National Strategic Materials and Minerals Program Advisory Committee, popularly known as the "Mott Committee" because of its distinguished chairman, retired Admiral William C. Mott.

Jan 1, 1986

By Ben E. Lindsly

The recovery or partial recovery of the oil remaining in oil sands after the usual methods of production have become unprofitable is perhaps the greatest problem in the petroleum industry today. The amount of this oil remaining in the sand is variously estimated by those familiar with the subject to be 25 to 90 per cent of the original content.2 Lewis3 states, "The estimate of 80 to 90 per cent of the oil left underground does not seem incredible."

Jan 1, 1926

By Phillip R. Moyle

A mineral survey of 19,350 acres of the Gooding City of Rocks Wilderness Study Areas (WSAs) in the north-central Snake River Plain was conducted by the U.S. Bureau of Mines in 1984. No formal mining districts are known in or near the study area. Forty-two placer claims within and adjacent to the study areas cover the Clover Creek diatomite deposit. Minor production from four pits was reported by the owners. The diatomaceous sediments are underlain by dacitic welded tuff and capped with basalt. Five exposures or blocks totaling 416 million tons of the diatomaceous material comprise the Clover Creek deposit; four of the blocks are in the study areas, out are predominantly covered by basalt. The North Clover block, just west of the areas, is only partially capped, and could be mined by open pit methods on the western flank of the exposure. The minable wedge contains an inferred marginal reserve of 35 million tons of diatomite possibly suitable for filter aid, filler, insulation, and other applications. At a production rate of 150,000 tons/year, total mining and milling costs for high-grade filter aid diatomite would be about $100/ton. The deposit is classed as marginal because products from this deposit may be inferior to currently marketed diatomite products. The market is well supplied by developed sources.

Jan 1, 1985