Search Documents

By Fabian Kirsch

Cyclic behaviour of axially loaded piles has been an issue since studies revealed that the capability to transfer skin friction into the ground is highly depending on the level and the number of load cycles the pile is subjected. It has been shown that degradation of skin friction due to axial cyclic loading leads to accumulating displacements and a severe reduction in pile capacity. In Germany the DIN 1054 as well as the Recommendations of the Working Group 2.1 ?Piles? of the German Geotechnical Society (EA-Pfähle) require the consideration of cyclic loading for the assessment of both the displacements and the capacity. Up to now no broadly accepted design method exists, which enables the engineer to give a reliable judgement on the pile capacity under axial cyclic loading and the displacements respectively. Instead numerous design charts make it possible to distinguish between stable and instable loading levels in order to ensure a design on the safe side. A newly developed design approach based on engineering models is presented which delivers a calculation algorithm for the remaining axial pile capacity after a defined number of load cycles to allow for the analysis of stability of the foundation. Furthermore the computation of accumulating displacements is made possible. The results are verified with pile load tests undertaken at Dunkirk, France and showed that the axial capacity after cyclic loading calculated with the newly developed design approach predicts actual capacity with an accuracy of ±20%.

Jan 1, 2011

By K. Rainer Massarsch

"Part 2 of 2 (Continued from Summer 2004 edition) By K. Rainer Massarsch, Geo Engineering AB, Stockholm, SwedenVibrations, which are caused by the installation of piles in dry or permeable soils, can cause settlements. The magnitude of settlements depends on several factors, such as soil type and stratification, ground water conditions (degree of saturation), pile type and method of pile installation (driving energy). A method of settlement prediction due to construction-induced vibrations has been presented by Massarsch (2000). However, in many cases, an engineering assessment must be made at an early stage of a project. The following simplified procedure can be used to estimate settlements in a homogeneous sand deposit adjacent to a single pile, Fig. 5. This approach is based on extensive experience from soil compaction projects. It is assumed that intense densification due to pile penetration occurs within a zone corresponding to three pile diameters. The volume reduction resulting from the propagating vibrations will cause settlements in a cone with an inclination 2V:1H, with the tip at a depth of 6 pile diameters. Thus the settlement trough will extend a distance of 3D+L/2 from the centre of the pile, with maximum settlements at the centre of the pile. Maximum settlements, Smaxand average settlements, Smax can be estimated using the following relationship, choosing an appropriate a value of the soil compression factor, from Table 2.The driving energy depends on the method of pile installation, soil stratification and the pile type. The displacement volume of the installed pile has been neglected. The simplified method is applicable for estimating settlements at the perimeter of a pile group. It should be noted that settlements also occur outside the assumed cone, but these are often negligible. The effect of incompressible layers should be taken into account by adjusting the effective pile length."

Jan 1, 2004

By Javier Rodriguez

Adaptive re-use of existing structures in urban environments has become very common due to lack of available space in our cities and requirements for increased structural capacity. Often, it involves retrofitting existing foundations to support increased loading. In such cases, Engineers face the need to review existing deep or shallow foundations for their true load carrying capacities in order to determine the required magnitude of retrofit work, if any. To accomplish this, the engineer must track down and cull through the existing construction documentation to determine what was actually constructed, complete an investigation to confirm these conclusions, possibly sample the foundation elements for strength properties, and on occasions complete non destructive or full scale load testing of indicator elements. This paper describes the typical procedure followed by the authors for design of retrofit schemes for existing buildings in the Washington DC metropolitan area. Three case histories are presented that illustrate various issues encountered during design.

Jan 1, 2006

"Guideline Augered Cast-In-Place (ACIP) Pile Specification and Commentary11.0 GENERAL1.1 SCOPEThe Pile Contractor shall furnish all labor, materials, tools and equipment necessary for furnishing, installing and testing Augered Cast-in-Place (ACIP) piles as shown on the Contract Drawings and as specified herein.ACIP piles are commonly referred to by several other names. Some of them are trademarks or service marks owned by Foundation Contractors and some are names that try to describe the installation process. The term “cast-inplace” is sometimes replaced with “cast-in-situ,” especially in Europe. Some common names are Auger Cast Piles, Intruded Mortar Piles, Augerpress Piles, Augered Pressure Grouted Piles, AugerPile Foundations, Continuous Flight Auger (CFA) Piles, Grouted Bored Piles, Augered Grout-Injected Piles, Drilled or Augered Uncased Piles, and Uncased Cast-in-Place Concrete Piles. To avoid confusion, ACIP pile will be used exclusively herein.1.2 PILE CONTRACTOR QUALIFICATIONSThe ACIP piles shall be installed by an experienced Pile Contractor who upon request of the Engineer shall submit evidence of successful ACIP pile installation under similar job and subsurface conditions, including a job supervisor who shall have a minimum of five years of method specific experience.The proper installation of the ACIP piles is dependent upon the procedures used by the Pile Contractor’s field representatives and equipment provided. The Pile Contractor’s personnel responsible for the installation should have relevant experience with the auguring and pumping equipment, experience placing piles under similar site conditions (including restricted headroom if appropriate), in similar subsurface conditions, as well as experience handling the special grout mixes, admixtures, etc."

Jan 1, 2016

By Pirooz Barar

The new Stanley Hall building will house the center for bio-engineering and technology research for the UC Berkeley campus. The structure is located at the northeast part of campus, adjacent to Donner Lab, on the west side of Galey Road, approximately 600 ft. from the Hayward Fault. The building site has a complex geological formation. To the east there are clayey soil shale formations, and to the west there is greywake shattered sandstone. The water table is at 10 ft. below grade. The structure will consist of 6 levels below grade and 8 levels above grade, which calls for an 83 ft. deep excavation on the northeast side. There is an approximately 35 ft. grade differential between the east and west sides of the building. Because of this severe grade differential, as well as high water tables, the lateral forces on the building due to uneven earth pressures would have been 2 times the magnitude of the seismic forces. To mitigate the lateral earth pressures, a permanent Soil Nailed Wall, integrated with the structural system of the building was designed. PB&A, Inc.?s in-house design program ?Winslope? was utilized to design the system and the data obtained from a rigorous monitoring program, were used to calibrate several computer runs using Plaxis program.

Jan 1, 2004

By Wu Jie Mei, Li Yao Liang, Franz-Werner Gerressen, Arthur Bi

Diaphragm walls (D-walls) are known as underground structural elements commonly used for retention systems and permanent foundation elements. In addition, they are also quite often used as deep groundwater barriers, called Cut-Off-Walls (COW). Shanghai ranks third among the most densely populated metropolises in the world. In 1990, only eight million people lived there. Today, Shanghai has about25 million inhabitants. The increasing demand to accommodate the infrastructure of growing megacities like Shanghai pushes the required depth for subway, sewage and foundation projects to the limit. Future projects will demand excavation depths of more than 100 m (328 ft) on a regular basis. Already carried out reference projects will be described and a general outlook for upcoming projects will be given. The paper also explains the installation process in general focusing on the use of trench cutter technology. INTRODUCTION D- walls are known as underground structural elements, commonly used as retention systems for excavation pits and shafts as well as permanent foundation walls or elements. It is anticipated that, with the increasing trend of utilizing more and more underground space to accommodate environmental considerations and urban/suburban development, there will be an increasing requirement for diaphragm wall usage in even more difficult conditions and with increasing depth. The trench cutter is the most important tool for performing this work. The hydraulic grab, a well-known and valuable excavation tool for d-walls reaches its limits in terms of depth and when cutting rock. Therefore the trench cutter technology will be in the focus of this paper. The trench cutter itself is a reverse circulation excavation tool. It consists of a heavy steel frame with two drive gears attached to its bottom end, which rotates in opposite direction around the horizontal axis. Cutter wheels are mounted onto the drive gears. As they rotate, the soil beneath the cutter wheels is continuously broken up, removed, mixed with the bentonite slurry in the trench and moved towards the opening of the suction box of the pump? A centrifugal pump located right above the cutter wheels conveys the slurry via a hose system up to a desanding plant. There the slurry loaded with soil and rock particles is cleaned and returned into the trench.

Jan 1, 2018

By Timothy C. Siegel

Drilled displacement piles (also known as augered cast-in-place displacement piles or augured, pressure grouted displacement piles) are installed by the displacement of soil and subsequent placement of fluid cement grout within the evacuated volume. Depending on the soil grain-size characteristics, soil behavior, in situ soil density, pile spacing, and pile diameter, the installation process can result in measurable densification and an increase in lateral stress. This paper examines the conditions prior to and following the installation of drilled displacement piles at sandy sites using the cone penetration test. The data support that the installation of drilled displacement piles results in a substantial increase in tip resistance.

Jan 1, 2007

By Hector Simchas

"1. BENTONITE: THE CRUCIAL CONSTITUENT OF SLURRYSuspensions of bentonite and water are used in a variety of applications in underground engineering. For the construction of underground elements like slurry walls or piles, bentonite slurries offer support to the excavation of loose soils and counter pressure against hydrostatic pressure of ground water, especially where soil permeability is high. In addition, for the construction of tunnels by the slurry-shield method or when hydromills are used for excavation, bentonite suspensions transfer the loosened soil to the surface. In applications like pipe jacking and microtunneling, or where high revolution drilling is required, bentonite also provides lubrication and cooling.To fulfill these functions, the properties of a bentonite slurry need to remain stable, or at least predictable, during the course of construction. Unfortunately, when a suspension mixes with earth, ground water and/or impurities, its properties may be compromised resulting to reduced performance, which would in turn lead to increased construction costs and the risk of the excavation collapsing. Our experience in the lab and onsite is presented herewith.2. MOST USUAL FACTORS OF PERFORMANCE FAILUREWater and soil quality are important factors defining the behavior of suspensions. In an extensive program of measurements in our technical laboratory, the effect of frequently encountered harmful substances on bentonite suspensions has been examined and the results are summarised in Table 1.Some tests show that the conductivity of water has a direct relationship with Marsh Viscosity. For example, we have seen that if the quantity of bentonite required to achieve a 40s Marsh Time ranges between 50-52 kg/m3 at water conductivity below 100 µS/cm; when conductivity is increased to 1,400 µS/cm, we need 65-68 kg/m3 in order to achieve the same property."

Jan 1, 2015

By Mai Yuanjian

The stabilization effect in large excavation slope with vacuum wellpoints system during construction of a dry dock located in Guangzhou is introduced in this paper. In-situ observations indicate that the effect of wellpoints for decreasing seepage in slope is remarkable even though the muddy sitty clay in it has poor permeability and the slope can remain its stability well. Meanwhile, a non-linear partial defferential equation has been set up to the whole unsteady seepage process as water level in the foundation pit excavated under water goes down to the bottom and so does the seepage in slope due to dewater by vacuum wellpoints system at the same time. And the finite-defference method has been used to solve the equation mentioned above, which differes from conventional wqy where the equation will be linearized firstly. Since the water heads in slope with wellpoints dewatering are more variable, it is necessary to keep non-linear. The calculation results are in good accordance with observation. Vacuum wellpoinnts for slope stabilization in this work is successful.

Jan 1, 1991

By Seffen Leppla, Rolf Katzenbach, Matthias Seip

"Abstract The economic and safe design of deep foundation systems in difficult soil conditions is based on a reduction of construction material used, construction time spent, energy consumed and a high-level modelling of the soil-structure-interaction. The special foundation system Combined Pile- Raft Foundation (CPRF), in-situ load tests on the construction site and a sufficient soil investigation allow cost optimised constructions. In any case at challenging projects the observational method has to be applied for verification and quality control of the design. Regarding the 4-Eye-Principle as basis of the quality control management an independent peer review of the planning, design and construction phases is the guarantee for safety, serviceability and optimisation of all projects. Main execution standards for the construction of deep foundations based on the Eurocode 7 are summarised and discussed. The paper presents the basics of the safe and qualified design and construction of foundation systems including quality assurance. The application in engineering practice is shown on achallenging project of high-rise buildings with difficult boundary conditions.IntroductionThe construction of deep foundation elements in inner cities are special challenges due to the limited space for the construction works and the effects on existing buildings (Figure 1).An economic and safe design of deep foundation systems in difficult soil conditions is based on the following main aspects:•,qualified experts for planning, design and construction•,interaction between architects, structural engineers and geotechnical engineers•,adequate soil investigation•,design of deep foundation systems using the Finite-Element-Method (FEM) in combination with•,enhanced in-situ load tests for calibrating the soil parameters used in the numerical simulations•,quality assurance by an independent peer review process (4-eye-principle) combined with theobservational method if necessary"

Jan 1, 2014

By William (Bill) H. Walton

"I arrived in Chicago in 1993 with Dr. Ralph Peck’s University of Illinois bulletin titled Engineering Properties of Chicago Subsoils (Bulletin 429), which he published in 1954 with William Reed. Being an outsider, I wanted to learn from Chicago geotechnical practice leaders that included Clyde Baker, Jr., John Gnaedinger, Charles Pfingsten, Dr. Safdar Gill, Robert Lukas and Dr. Jorj Osterberg, who have influenced foundation designs for the structures that make up the contemporary Chicago skyline. One of my immediate goals was to get the Illinois Structural Engineering license to be on par with the likes of Eli Cohen, Mike Tylk, Stan Korista, Bob Halverson, Joe Burns, Ron Johnson, Bill Baker, Bob Sinn, Chuck Anderson and Dave Eckmann, who have led their structural firms in the design of the skeletal core and frames of many of Chicago’s iconic buildings (and for many other buildings around the world). From my time with GEI Consultants (GEI), then on with STS Consultants (STS, and now AECOM), and now back with GEI, I have had the opportunity to analyze and design foundations and, with the help of many skilled foundations and building constructors, to verify that predicted foundation performance matches actual movement data. The theme of Chicago’s foundation design practice is to assume and verify. In 1948, Peck published the History of Building Foundations in Chicago (Bulletin 373) that was updated in 1998 by Baker, Pfingsten and Gnaedinger, who meticulously documented hundreds of Chicago’s foundations, and have shown the value of advanced analyses and testing to advance the deep foundation design practice that includes a variety of high-capacity driven and drilled deep foundations. Mehmet Uyanik, Peck and Baker have made Chicago’s subsurface into a full-scale foundation test laboratory. They confirmed soil mechanics principles like Terzaghi’s 1-D consolidation theory when early foundations bearing on sand-clay crust over soft to medium silty clays (e.g., Auditorium, Masonic Temple, Monadnock Block and Old Board of Trade buildings) took 40 to 60 years to consolidate clay 1 to 2 ft (0.3 to 0.6 m). They also confirmed proven increases in bearing pressures based on measured performance of deep foundations bearing on the glacially derived hardpan clay till and in solid dolomite that underlies Chicago."

Jan 1, 2017

By X. L. Huang

This paper deals with the experimental and theoretic study of the contact pressure beneath the deep foundation of Beijing International Hotel, The experiments have been carried out in project and in model footing 6.6m2. The result of measurements shows the contact pressure at the edge is greater than that at the center. The theoretic analysis on the base of elastic theorey is in good agreement with the test if the proposed assumption used.

Jan 1, 2010

By Alan J. Lutenegger

A series of tension tests were performed on prototype scale steel pipe piles at two sites to evaluate the influence of scale and pile plugging on the unit skin friction developed in axial tension. The first site consisted of a clean medium dense fine sand above the water table. The second site consisted of a loose silty sand with the water table within about 0.5 m of the ground surface. Pile load tests performed at each of the sites included piles with diameters ranging from 73 mm to 114.3 mm, which may be considered driven "micropiles". At the first site, pile lengths of 6.1 m were used; at the second site, pile lengths of 9.1 m were used. Some of the piles were driven open-ended while others were fitted with a conical tip to form a closed end. During installation, pile plugging measurements were taken on the open-ended piles after each 0.30 m of penetration. The piles were allowed to rest for a period of about 30 days after driving prior to performing the axial uplift load tests to failure. The results indicate that in the medium dense fine sand the unit skin friction developed in tension is dependent on both the amount of plugging that occurs and on the size of the pile, which was not the case for the loose silty sand.

Jan 1, 2000

By Mary Ellen Bruce

Let me first address the issue of the wet grab samples. The wet grab samples that were attempted to take on the Central Artery were hindered by the fact that the way the mixing was being done was only by injecting grout on the way out, during withdrawal of the mixing tools. They would auger down to the required depth (usually with some water being injected), which took anywhere from 45 minutes to an hour, and then when coming out, the grout would be injected with grout. That was leaving a column of grout in the center where the shaft had been (i.e. inside of the blades of the mixing tools), which would end up being something like a foot in diameter because the pipe that was used for the drill shaft was a foot in diameter. So we had 10 inches to a foot of almost pure grout in the middle of our column and then we had 2 feet on either side that was mixed soil cement. So when they went down with the wet grab sampler not knowing where that was in the column sometimes they/we were getting strengths of 1500 psi, and sometimes they/we were getting strength of 500 psi or 100 psi. So what was it that we were taking into the wet grab sampler? In those cases you don't really know, but it wasn't representative of the core samples we were taking. We were purposely not coring in the center because we knew that was going to be high cement content, almost pure grout. So the issue of wet grab sampling particularly on this project, the Central Artery Project, was that we didn't really know what we were sampling. What becomes an issue with wet grab sampling in other projects is that you have to have another device (machine) in most cases, a cherry picker crane or something similar that can raise and lower with a beam that is used to forces the sampler down into the freshly mixed soil-cement. And regarding economics, is it more economical to have that crane standing by with its operator or to have a drill rig to come along later and do the coring and take the material out that's fairly identical to what you're finding in situ? The complaint of micro-fracturing in the core samples as you're taking the cores was raised by Seiko as causing large strength reductions. But, if you're doing it carefully, then I don't think that's much of an issue anymore, on research basis perhaps but not on a practical level.

Feb 10, 2003

By Wang Mingshu

The pile foundation is a kind of advanced foundations in the filled or soft soil. In this paper, through the actural engineering of coal dressing plant of Western Opencast Coal in Fushun built on the mining dump with large diameter pile foundation, the construction method and mechanics analysis of pile are given. Unless it is in following stadge, the stability of pile cannot be lost due to its small rigidity. The analysis shows that pile foundations of large diameter ellipse section can decreased hotizontal displacement to 60% ?70% of that of equal section an in the design of a single pile and a single column, the ellipse pile and manual dig hole are most favourable. So a large amount of concrete can be saved.

Jan 1, 1991

By D. Dreher Whetstone, Paul M. Blakita, Christopher M. Reith, Ravi P. Malviya

"Micro-piles are small diameter (5 to 10 inches), cast-in-place piles which can develop high load capacities by bonding with soil or rock. Micro-piles are particularly well-suited for moderate to heavily loaded structures requiring deep foundations in difficult subsurface conditions, such as karst, bouldery mine spoil, or unsuitable fills with concrete debris or other obstructions. Attempts to install conventional deep foundations including driven piles, drilled piers, or auger-cast piles are likely to be fraught with construction difficulties and disputes, delays, cost overruns, and may be unfeasible in some cases. Micro-pile installation equipment is very effective in installing foundations through such overburden or rock materials.This paper presents case histories of Micro-pile installations on two projects with difficult soil/rock materials. The project sites are located in Charles Town, West Virginia and Masontown, Pennsylvania.Charles Town, West Virginia ProjectThe Charles Town project entailed construction of a four-story pre-cast concrete garage. Triad Engineering, Inc. performed a geotechnical investigation for this project (Triad, 2001). The subsurface, geologic, and project specific information described in th is paper are largely based on the aforementioned geotechnical report.Ground ConditionsThe project site is located in Jefferson County, West Virginia, and is mapped to be underlain by the Elbrook Formation. This formation is described as argillaceous, dolomitic limestone with beds of dolomite and aphanitic and algal limestone (Dean, et al. , 1990). The carbonate rocks at the site were characterized as ""moderately solution-prone, highly calcareous and weathers differentially to produce a pinnacled or ""sawtooth"" top of rock profile. (Triad, 2001 )"" Overburden soils consist of low to high plasticity, fine grained residual soils formed by weathering of the parent carbonate rock. The residual soils include variable proportion of sand and rock fragments."

Jan 1, 2005

By Lois G. Schwarz

I did a project (Sungai Piah) as a consultant to your firm in Malaysia, where we were faced with a similar situation as sketched out in your question. The following is what we did for the grouting of the primary holes, which were both located upstream of the plug as well as downstream: We used a hydrophobic MDI based semi-rigid polyurethane prepolymer in the first phase of the grouting operation when grouting under water flow conditions. Then in the second phase and also for the contact grouting we used a two component water compatible polyurethane elastomer. And then for deeper formation grouting, when all the water flow had been stemmed in the vicinity of the plug, we used a regular (balanced stable) cement based grout. So it may not exactly answer your question, but we first used hydrophobic grout because it is very efficient to grout a formation through which water flows. We didn't stop all the leaks day-lighting downstream of the plug or all water running through the formation near the plug, but the flow of water through the rock formation adjacent to the plug was reduced by 99.9%, after completing the urethane grouting. This facilitated the placement of cement based suspension grouts without wash-out.

Feb 10, 2003

By Ilhan Chang, Ernest Nsabimana, Kiseok Kwak, Juhyung Lee, Young-Hoon Jung

"Numerical analyses were performed to analyze the behavior of two different type of suction piles (mono type and group type) under various soil layer conditions (uniform silty clay layer, uniform silty sand layer, and two-layer deposit consisting of clay and sand layers) and lateral loading locations (top, middle, and bottom of the suction pile). According to the results, mono suction pile shows maximum resistance when load is applied on its middle, regardless of the soil layer conditions, while group suction piles varies significantly according to the allowance on head rotation. When head rotation is allowed, the behavior of group type piles become similar to the behavior of mono suction pile. Whereas, when rotation is prevented, resistance is maximized when load is applied on the top head. Moreover, group suction piles show higher efficiency regardless of the ground condition and geological stratum. For further advances, concrete block on the top of group suction piles are suggested as an effective alternative method to prevent partial rotation and maximize ground resistance for group suction piles.IntroductionWith the development of offshore technology, applications and real site installations of suction piles are increasing significantly nowadays. They are generally used as mooring anchors in various floating structures, marine platforms, and offshore wind turbines. According to its convenience in installation and removal, suction type foundations are becoming good alternatives for deep ocean support systems. The bearing capacity is similar to the bearing behavior of ordinary offshore structures (piles or drilled shafts). The most common use of suction caissons is anchors for catenary mooring lines, where the chain angle at the mudline is close to zero (Randolph, 2002; Sharma, 2004).Recently, it is reported that a huge isolated single suction pile can be replaced by a group of moderatesized suction piles (Randolph et al. 2004). A single monopile is easy to be produced and installed in site. It is expected that monopile foundation is not applicable for deep depths because it has a limitation on penetration according to its huge side skin area (i.e. friction). Moreover, stiffness requirements sometimes render thicker pile wall conditions which are impractical to be produced."

Jan 1, 2017

By Arturo Ressi di Cervia

"The Construction of the Thrust Pits for Jacking of the I-90 Tunnel for the Central Artery/Tunnel Project (Part of Contract No. C09A4) in Boston MA was nominated for DFI’s 2002 Outstanding Project Award. In the judging, the project and the specialty subcontractor, Treviicos Corporation, was chosen for a Special Recognition Award. INTRODUCTIONBoston’s Big Dig, as the construction of the underground artery became known, is undoubtedly the largest urban construction project of this century.The Central Artery/Tunnel Project, or CA/T, to call it by its proper name, runs approximately eight miles through the heart of Boston, five miles of which are built underground while maintaining traffic on the elevated existing structure, while at its southern end I-90 is extended to Logan airport under active rail lines, Fort Point Channel and Boston Inner Harbor.Since the alignment of the road closely parallels the shoreline as it existed in colonial times, the cut and cover construction had to contend with substantial portions of filled ground, not to mention existing subway lines, live utilities, building foundations and, last but not least, the irritable Boston drivers and litigious adjacent property and business owners.Consequently, while it is impossible to single out the most difficult or challenging contract, the jacking of the tunnels of I-90 under the live rails of Amtrak certainly will rank high on the list.Never before, anywhere in the world, was an attempt made to jack tunnels of this size: the South Bay Interchange consists of three 78 feet (24 m) wide by 38 feet (11.6 m) high tunnels, the shortest of which is 167 feet (51 m) long. TECHNOLOGYIn order to achieve this engineering feat it was necessary to consolidate the soil under the track to prevent it from moving or settling during the jacking process. After a detailed analysis of the geological profile to be traversed it was decided that freezing was the most suitable method, since it could be applied to the full range of soils present on the proposed alignment."

Jan 3, 2003

By Takefumi Takuma, Masashi Nagano, Christopher DellAringa

Multiple agencies in Southern California are retrofitting and upgrading their levees to catch up with ever-advancing urbanization affecting the requirements for existing channels and levees in this seismically active zone. Pressed-in sheet piles have been specified on some of these projects to minimize noise and vibration problems associated with sheet pile installation. This paper will study three Southern California levee and sewer pipeline retrofit projects that utilized pressed-in sheet piles in hard soil conditions with N-values higher than 50. BACKGROUND Southern California is home to numerous drainage channels fortified with earthen levees. In spite of the region’s semi-arid climate with varying annual precipitation from year to year, winter storms can bring in heavy and continuous rainfall to the area which overwhelms the levees’ capacities at times. Some levees are running through densely populated areas with homes and other sensitive structures such as underground utilities and bridge piers. Conventional sheet pile driving utilizes either percussive or vibratory pile driving methods, both of which generate high levels of noise and vibration, causing nuisance and potential damage to nearby structures. On the other hand, the press-in piling method utilizes a hydraulic force to push piles into the ground, thus practically eliminating the noise and vibration issue. Although there are types of press-in piling systems mounted on tall leaders on large crawler-base machines, they are less frequently used due to its much larger size and more limited drivability than the type discussed hereunder. The other type of press-in machine sits on top of already installed piles and is anchored with its own weight and additional counter weight when starting off as shown in Figure 1. Once the first few piles are pressed in, the equipment grips on top of the installed piles and moves forward on its own as the pile installation progresses. See Figure 2. This method does not use a vibratory or percussive force to install piles.

Jan 1, 2018