Search Documents

By Kishore Kumar B., Eswaran Prasad C R, Srini Naik B., Ramakrishna Raju N

The authors through this paper intend to introduce the non-vibro technique of ground improvement by stone column, being used for the first time in India under the Western Dedicated freight Corridor in Mumbai area. New 2x25 KV double line dedicated freight corridor tracks, capable of carrying 32.5-ton axle load are proposed to be built on this stretch. Non-Vibro Displacement Stone Columns of 900 mm diameter were installed to improve the safe bearing capacity of the soft ground to take the loading of Dedicated Freight Corridor Railway embankment. Vertical footing load tests on single and three column groups were conducted to assess the improvement in the sub-surface condition after installation of stone columns. This paper describes load tests conducted on stone columns and analysis of the obtained results. The observed load settlement behaviour of the improved ground has also been presented. Behaviour of single and group of stone columns have been compared and criteria adopted for arriving at desired factor of safety based on the settlement observed, has also been discussed.

Nov 1, 2022

By Jeremiah M. Jezerski, Russell H. Lutch

The Mount Olivet Road Drop Shaft (MOR-DS) support of excavation (SOE) is a circular unreinforced concrete shaft with an inside diameter of a 30.5 ft (9.3 m) and depth of 120.5 ft (36.7 m), constructed using slurry wall methods. The SOE for the adjacent Mount Olivet Road Approach Channel (MOR-AC) and Mount Olivet Road Ventilation Vault (MOR-VV) near surface structures (NSS) consists of lean mix concrete walls and cement-bentonite walls, respectively, both constructed using slurry wall techniques and reinforced with embedded soldier piles. NSS SOE required multiple levels of preloaded internal bracing, with excavation depths of up to 75 ft (22.9 m). The original design construction sequence for the shaft and NSS SOE required that the MOR-DS be constructed in its entirety and backfilled to ground surface prior to excavation of the adjacent NSS SOE. After installation of the drop shaft and NSS SOE an accelerated construction sequence was implemented requiring the analysis of the excavation support systems to determine if the excavations could be open concurrently without adversely impacting the partially constructed permanent MOR-DS structure. The MOR-DS was analyzed using the finite element analysis (FEA) software, MIDAS GTS, to demonstrate that the unbalanced loads applied to the MOR-DS composite structure due to the revised sequence would not exceed the strength and serviceability requirements per ACI-350 or superseded by the more stringent project requirements. The results of the FEA were used to set limits for geotechnical instrumentation consisting of strain gauges located on the brace levels of the NSS SOE. A comparison of the SOE design hand calculations, FEA model results and instrumentation data is presented.

Oct 1, 2022

By RavikiranVaidya, Vishal Dhamecha

Low Strain Pile Integrity Testing has been used in India since 1990’s and several have tried to demonstrate the utility and benefits of this method. However, use of this technology was limited till 1998 as not enough data maybe was not available to justify its use and application on major infrastructure and real estate projects. The first author has done significant work in this method resulting in its use in practically all sectors of the industry that use concrete bored pile foundations as a supporting element. The paper explains various signal enhancers or modifiers involved in processing of low strain test data and its implication on the final output. It also describes how the method can lead to abuse or can provide poor interpretation if incorrectly used. The current effort is to demonstrate that data collection and evaluation becomes complex with changes in soil stratum and pile profile. The paper highlights the present testing practices and provides a guideline for classification of pile integrity into few simple categories in Indian context rather than writing complex interpretations.

Sep 1, 2022

By Arash Saeidi Rashk Olia, Dunja Perić

The increasing demand for renewable energy has attracted attention to energy geostructures as means of extracting clean geothermal energy from the ground. To further advance the understanding of soilstructure interaction in energy piles analytical solutions considering the self-weight of the pile were derived. These solutions were then incorporated in recently-derived thermomechanical weightless solutions to provide comprehensive analytical solutions for axial displacement, strain and stress in single energy piles. This was accomplished by comparing responses of energy pile under different loading scenarios that reflect presence and absence of the self-weight. Results of mechanics-based analysis revealed that the self-weight of energy piles embedded in stiff soils has no significant contribution to displacement, strain and stress that develop under thermo-mechanical loads. Overall, the significance of the self-weight contribution depends on the magnitude of thermal load as well as the soil-pile interface stiffness. The stiffness of end restraints imposed to the pile head and tip were also found to play an important role in contribution of self-weight in induced thermomechanical stresses in energy piles.

Oct 1, 2022

By Ingrid Engeset, Solve Hov, Arnfinn Endal, Per-Anders Mortensen, Priscilla Paniagua, Bjørn Kristian Fiskvik Bache

During the last decades, it has become common practice in the Nordic countries to use dry deep mixing in soft clays with lime and cement in for example deep excavation pits in soft clay, or as a reinforcement of the passive zone within sheet pile walls. The shear strength of stabilised soils is affected by the stress conditions during curing and shearing. However, this is normally not taken into consideration. As the strength of the stabilised clay is stress dependent, excavation of the overlying soil will lead to a reduction of the confining stresses in the underlying stabilised soils which means that the shear strength will also be reduced. Under embankments on the other hand, the effect is reversed as the shear strength will be increased. In this study, laboratory tests have been performed on stabilised soils cured and tested under different stress conditions to quantify the stress effects in a Norwegian sensitive clay. In addition, direct simple shear tests on samples from in situ columns have been made with varying normal stresses. Results are presented showing an increase of shear strength of the stabilised soil with increased curing stresses, and an even higher increase with increased confining stress during shearing. The results are compared to field measurements along with a discussion of practical application of the findings.

May 1, 2022

By Karsten Beekhaus, Sander W. Odijk, Rabea Bahlum, Mazin Adnan, Ayman Abdelh Al Nuaimat, Hassan Farhat

The Arab Potash Company, APC, is one of the 10 largest potash producers of the world. The solar ponds at the Dead Sea, used for the enrichment of the salt content in the brine, are of crucial importance for the first step in the exploitation of the potassium salt. Targeting at the expansion of production in the since over 50 years utilized facilities, the increase of the brine exploitation capacity, reducing the substantial brine seepage losses from the ponds, becomes a crucially required measure. In this context, the remediation measures on the over 11 km long Dyke 1, being a main dyke of the solar ponds system, became inevitable to reduce the brine losses, prevent further development of sinkholes and cavities and hence assuring the stability of the dyke. The highly aggressive environment, the acting hydraulic conditions and the sensitive stratification and nature of the existing ground represented remarkable challenges for the design, as well as its implementation by the construction activities. Royal Haskoning developed a solution addressing the challenges above and targeting at a high sustainability of the executed structure, especially in view of the various geological and hydrological hazards repeatedly occurring in this Dead Sea region, including sinkholes of several meters by diameter and depth. The construction works, consisting of a cut-off wall, with depths reaching down to 31 m, were awarded to Bauer International FZE, a subsidiary of Bauer Spezialtiefbau GmbH. Upon the execution of the first section of 4.2 km length, additional sections were subsequently commissioned, also on further dykes, totaling to about 300,000 m² of cut-off wall. The specific project conditions, such as utilization of cutter technique for the excavation in Halite rock, the stability of open trench exposed to hydrostatic pressure of salt-saturated ground water, resulted in unconventional requirements towards the supporting fluid. The extremely aggressive saline conditions –with a Dead Sea water density of 1.25 tons/m3; one of the world's saltiest water–, were further a decisive factor for the definition of the backfill material concept. Despite its clear advantage for construction of cut-off walls with installed sheet piles, the single-phase system with hardening slurries, fulfilling both functions of excavation support and cut-off wall backfill material, had to be abandoned in favor of the two-phase system, to construct a hybrid cut-off wall made of sheet piles and plastic concrete.

May 1, 2022

By Adrian Gygax, Sarah Gaib, Rod Kostaschuk

The British Columbia Ministry of Transportation and Infrastructure (Ministry) recently completed a slope stabilization project at Ten Mile Slide on Highway 99. The highway is an essential part of the road network connecting the British Columbia (BC) coast with the interior of the province. The landslide was first identified in the mid-1980s and has retrogressed more than 250 m upslope since then, leading to continual and expensive repairs to the highway. The Ministry engaged BGC Engineering Ltd. (BGC) and their structural sub-consultant Gygax Engineering Associates Ltd. (GEA) to develop a stabilization scheme that would halt the slide with an acceptable level of residual risk. The design required careful consideration of construction stages and the stresses induced in the structural components as the slide movement was progressively stopped as construction advanced. Four stabilization design options were shortlisted with the preferred option selected in Fall 2016. The selected solution comprised the construction of five rows of post-tensioned soil anchors upslope of the highway and a tied-back concrete tangent pile retaining wall for the roadway itself as well as reconstruction of the highway alignment, grade and drainage through the slide. Works were installed by top-down construction within defined time allowances stipulated in the contract. Significant engineering was undertaken beyond standard design processes for this complex project, such as comprehensive geotechnical investigations, aerial and terrestrial laser scanning and change detection analyses, pre-production test anchors, detailed geo-structural numerical modelling and due diligence activities to validate and optimize the design. The stabilization works have been very successful with the slide response being as predicted and the highway operating again as full two-lane service.

Oct 1, 2022

By Henry H. Tayler, Eric Sturel

1 Triton Square was originally a six-storey building with a one-level basement located within a commercial development near Euston, London. It was designed and constructed in the 1990s and the foundation scheme comprised straight shafted London Clay piles arranged singly beneath columns. The scheme added three storeys and a five-storey infill in the central atrium area to increase the building floorplate by 70% and maintained the usability of the basement space. As the loads to support the additional floorplate area were greater than the capacity of the existing foundations, an optimised strengthening scheme of small diameter piles installed within the existing basement and a slender retro-fitted raft was installed to augment the existing piles. The re-use and strengthening of almost all of the existing foundations enabled re-use of a very high proportion of the superstructure and in approximately 35,000 tonnes of concrete and 1,900 tonnes of reinforcement and structural steelwork being re-used. The structural embodied carbon for the refurbished building scheme is estimated at an average of 136 kgCO2e/m2, achieving a Structural Carbon Rating Scheme (SCORS) “A” rating with components detailed in the paper.

May 1, 2022

By David Corke

The paper presents the development of Federation of Piling Specialists (FPS) calculation of rig track loading, the production of the Building Research Establishment document “Working platforms for tracked plant” (BR 470), working platform testing and considerations of rig stability. The paper also discusses the importance of rigorous and well documented procedures and proposed future development of rapid working platform testing methods. Topics presented include the fundamental requirements and principles involved in the testing, design and maintenance of working platforms, rig track loading, the BRE design method and site testing analysis. The paper stresses the need for testing and design processes to be robust and simple and quick to perform as there is often little time between the award of a contract and the need to start work on site. Also, it is vital that all aspects of working platform design can be carried out with information that is available to the platform designer. Developments in the UK over the last two decades have resulted in improved quality and safety of working platforms that will hopefully be further enhanced as design and testing methods continue to improve.

May 1, 2022

By Leong, William. Chong, Kam Weng

Deep Vibro Techniques namely Vibro Compaction (VC) and Vibro Replacement (VR) are widely used in ground improvement to densify sands and strengthen cohesive soils. This paper describes the application of these techniques for the construction of 20 Ha Iron Ore Stockpile Yard with the maximum stockpile height of 14 m in Quang Ngai, Vietnam. The challenges of this project are to limit the stockpile allowable settlement and the surrounding pile’s lateral movement. The soil condition can be summarized as 12m – 18m thick of loose to medium dense SAND with qc around 5-18MPa and followed by 2.0 – 6.0 m thick soft clay with qc around 0.4 – 0.8MPa. Localized very dense sand layer was found. VR using stone columns were installed in soft clay layer while VC was adopted to densify sand layer. Additional shallow stone columns were built in sand strata to minimize pile top lateral movement. The post construction performance was verified by a large 6 m by 12 m plate load test (PLT). The predicted PLT deformation using Priebe’s improved properties for the VR will be presented and compared with the measured plate load test results.

Nov 1, 2022

By Dr. Anup Kumar Mandal, Partha Roy, Shuvranshu Kumar Rout, Dipak Mandal, Biswajit Das

Installation of a new scalping station with bunker, apron feeder, scalping screen, ramp -retaining wall and approach bridge was planned in an existing integrated complex of phosphate fertilizer at a remote place in West Africa. Rock phosphate ROM, transported from mines by a combination of 100 Ton and 150 Ton dumper, would be fed to a steel bunker having capacity of 180 m3. Different options were studied for retaining wall at the junction of ramp and approach bridge. Initially options with conventional RCC Retaining Wall, Gravity Retaining Wall with Precast Concrete Blocks and Reinforced Earth walls were studied. Option with Reinforced Earth was selected as this option was much more cost effective compared to other options. But real engineering challenges cropped up when competent execution contractors were not available nearby the site. To minimize the cost, an innovative option with Stepped Retaining wall was then studied. Geotechnical parameters of native soils, selected for the construction of the approach ramp were determined and it was found that with available poor geotechnical parameters of the native soils, design of stepped retaining wall would not be feasible with respect to available bearing capacity, subjected dead load, live load, operational load and earth pressure. A conscious effort was then made to make the design feasible by improving the geotechnical parameters of the retained earth of ramp near the retaining wall. In view of that, mix design with locally available materials like Silexite, Sand, Laterite, Gravel and Silt at different proportions was made and samples were tested in the laboratory to determine relevant geotechnical parameters. Based on the test results, a suitable mix was selected that had high shear strength, enhanced bearing capacity and improved coefficient of earth pressures. Design of stepped retaining wall was then made with the selected construction materials and construction completed. The plant was successfully commissioned in December. 2021.

Sep 1, 2022

By Selvaganesh Selvaraju, Deepak Raj, Sandun N. Wimalasena

One of the world leading oil majors is carrying out a multi-billion-dollar expansion of its integrated manufacturing complex in Jurong Island, Singapore, the global oil trading and refining hub. Soil conditions at the site comprise 10-20m thick reclaimed sand, below which is 3-5m of soft marine clay underlain by stiff soils of the Jurong Formation. The conventional foundation solution would adopt driven precast concrete spun piles; however, precast spun piles have a high embodied carbon from the usage of steel and cement. In order to reduce the carbon footprint, an alternative solution comprising deep vibro techniques was developed. The EFFC-DFI carbon calculator was used to demonstrate the expected scope 1, 2 and 3 carbon emissions for both driven pile and vibro techniques. By using in-house, state-of-the-art fuel-efficient machines, alongside the innovative design concept and usage of natural materials such as sand and stones, actual CO2e emissions were reduced from a potential 21,000 tonnes, with the spun pile’s solution, to only 1,900 tonnes. The saved 20,100 tCO2e is equivalent to an average car driving 2,000x around the Earth’s equator. The paper discusses the application of soil improvement as a more sustainable, lower carbon alternative to conventional piled solutions.

May 1, 2022

By Bartho J. Admiraal, Antoine Feddema

Pneumatic sinking of caissons has been established from mid-19th century. The technique of pneumatic sinking has been applied on many projects for underground construction up to depths over 20m below groundwater level since that time. Volker Staal en Funderingen, a known deep foundation contractor in the Netherlands, was awarded two contracts in 2015 for sinking in total 2 caissons in Hamburg (Germany) to large depths (over 30 m (100 ft) and two projects near Amsterdam (the Netherlands). The latter concerned two gate chambers for the world’s largest sea-lock, one of them was 55x81 m2 (180x266 ft) to a depth of 25.5 m (84 ft), which would mean a world record for pneumatic sinking! But with depths and dimensions like these, the deployment of personnel is the main limiting factor for production, despite all developments to date. It was decided to develop a remote controlled process, including the necessary equipment and monitoring systems. Monitoring not only the kinematics of the equipment in the working chamber and the production parameters related to the excavation but also of the structural behaviour of the sea-lock gate chambers was essential for approval of this innovative execution method. The lay-out and the sizes of the largest caisson the structural integrity was extremely critical for torsion and bending moments. A displacement controlled execution by the observational method was therefore required. In engineering a new approach for modelling the semi-continuous failure mechanisms of the soil was needed to understand the sensitivity of the excavation process and to define limit values for the execution. In the paper these structural and geotechnical issues will be explained together with the experiences during the execution.

May 1, 2022

By Aaron L. Sacks, David R. Good, Srinivas Yennamanda, Joseph K. Carey

Construction of Parcels 6 and 7, the second phase of The Wharf, began in 2019 and geotechnical construction was completed by December 2020. The overall project consisted of horizontal site, parks, and office buildings. The Wharf’s Phase 2 development includes approximately 1.2 million ft2 (110,000 m2) of above-grade construction including five multi-story, mixed-use buildings constructed over up to three levels of underground parking. The site is located between the WMATA Green Line Tunnels to the north and the Washington Channel to the south; it is bisected by a 108-in. (2740-mm) diameter DC Water outfall pipe. This arrangement, along with very difficult ground conditions, created challenges in the geotechnical design and construction. The support of excavation for this complex project required several different methodologies, including sheet piles, soldier piles, displacement piles, tiebacks, deep foundation anchors, jet grouting, and internal bracing with multi-tier rakers. Ground improvement was also required for support of spread footings in soft soils over the garage footprint. Underpinning of the active 108-in. (2740-mm) diameter DC Water outfall pipe running on a north/south alignment through the center of the site between the two garage structures was also performed. Since portions of the support of excavation are below the groundwater table, an extensive pre-excavation dewatering program was necessary and was separate from the foundation package. On the north side of the project, support of excavation (SOE) was required on a curved alignment, offset approximately 10 ft (3 m) from the outbound Green Line tunnel. Due to the proximity of the tunnel, a stiff, near-zero displacement wall was required. A portion of the buildings extend over the tunnels, imparting load to the tunnels to approximately restore original overburden loads excavated for the basement space. The building foundation is a 3 to 4-ft (0.9 to 1.2-m) thick mat slab anchored into the Potomac clay formation. Continuous movement monitoring of the tunnels was performed by an automated system. This paper describes the design and construction of the SOE and foundations for this high-profile project, which required collaboration between the Owner, Engineer, Construction Manager, and Specialty Geotechnical Contractor to solve many challenges.

Oct 1, 2022

By Tian Miaomiao, Cheng Yin, Shen Jun, Yu Hao, Li Yafei

Vast amounts of waste drilling mud containing heavy metals is produced during oil drilling process, which causes great pollution to the environment. Therefore, it needs to be treated until it is harmless. This study uses industrial waste and Portland Cement stabilized waste drilling mud; the unconfined compression strength, leaching amount of Pb2+ and Cr6+ ions, and pore size of the stabilized soil were tested at different times during freezing-thawing cycles. The antifreeze performance of the stabilized drilling mud with industrial waste is discussed. The results show that the strength of the stabilized soil decreases with an increase in the number of freeze–thaw cycles. The strength loss of the stabilized soil after freeze–thaw cycles can be effectively reduced by increasing the industrial waste content, especially the content of phosphogypsum in the stabilizer component. Pb2+ ions and Cr6+ ions can be effectively stabilized by industrial waste. The results of the pores test prove that the compactness of stabilized soil solidified by industrial waste residue is greater than that of cement alone.

Nov 1, 2022

By Chris Harnan, Christophe Justino

The European Federation of Foundation Contractors (EFFC) and the Deep Foundations Institute (DFI) jointly published Edition 1 of the ‘EFFC/DFI Guide to Support Fluids for Deep Foundations’ in April 2019. This Guide was prepared by a Task Group comprising experts on deep foundations from contractors, materials suppliers, consultants and academics. The Guide builds on work carried out by the Tremie Concrete Guide Task Group and presented in Edition 2 of the Tremie Guide. The Paper discusses and describes the content of the Support Fluids Guide which presents the state of the art on support fluid management, as well as the R&D work currently being carried out and funded by EFFC and DFI sponsors through an ongoing Field Research Study (FRS) as well as a review of academic research linked to the EFFC/DFI joint effort aimed at improving knowledge and guidance on support fluids. The FRS and academic research will help to improve the understanding of relevant support fluid properties including stability of excavations, interface layer formation, effect of filter cake and the development of new sampling and testing methodology. The Paper also presents the initial findings from the FRS program as well as a discussion on the challenging aspects of support fluid management with emphasis on design, performance, testing, and the environment.

May 1, 2022

By Gerald Verbeek, Erick Baziw

Cone penetration testing (CPT) is a popular and cost effective tool for geotechnical site characterization. CPT consists of pushing at a constant rate an electronic penetrometer into penetrable soils and recording cone bearing (qm), sleeve friction (fs) and dynamic pore pressure (u) with depth. The measured qm, fs and u values are utilized to estimate soil type and associated properties based predominantly on empirical correlations. The cone bearing measurements are highly susceptible to additive measurement noise for sandy, silty and gravelly soils. This measurement noise results in high peaks due to interbedded gravels and stones and low peaks due to softer materials or local pore pressure build-up. To date there has been little progress in filtering this additive noise aside from ad hoc techniques, which include discarding qm measurements and smoothing/averaging qm measurements. This paper outlines a qm filtering technique which attempts to put structure into the estimation problem. In this case, the dynamics of the cone bearing measurements are modelled within a state-space mathematical formulation and a Kalman filter (KF) is then utilized to obtain optimal estimates of qm. The mathematical details of the qm KF algorithm are outlined in this paper along with the results from a challenging test bed simulation.

Oct 1, 2021

By Douglas R. Hardin, Stanley L. Worst, Joanna Mason

A challenging earth retention project presented itself in Washington, DC in the backyard of the historic House of the Temple (The Scottish Rite of Freemasonry, Supreme Council 33°). Located at 15th St NW and S St NW, a forty-foot-deep underground basement was to be installed adjacent to the existing Temple, a historic Carriage House structure dating back to the 1800’s and across a narrow alley from a four-story brick apartment building. The unique geology of the site included typical urban fill overlying a mixture of loose alluvial soils underlaid by dense marine deposits of the Potomac Formation. The clay, sand and gravel of the Potomac included nested boulders up to three feet in diameter. Design of the earth retention system accounted for ground conditions, installation methods and estimated movement of the system and adjacent structures. Anticipated ground water and unanticipated water from leaky sewers also proved obstacles to overcome during construction. Soldier beams were installed using a variable momentvibratory hammer to minimize disturbance to the historic and sensitive structures. Monitoring of the existing structures included both seismograph and optical targets during installation of soldier beams and as the excavation progressed. Micropiles drilled into the Potomac Formation were a part of the permanent foundation for the new structure. This local case history will delve into the details of the successful design, installation, and performance of an earth retention system and micropiles in a historic and highly congested urban environment.

Oct 1, 2022

By Chris Leach, Lucie Spencer

This case study describes the geotechnical aspects of the basement construction for a multi-storey, residential and hotel complex located in the newly developed Elizabeth Quay precinct in Perth, Western Australia. The development included a three-level basement for car parking covering the full site area which was constructed using the top-down construction sequence. Soil conditions generally comprised 2m of fill overlying medium to dense clayey sands that in turn were generally overlying a very stiff clay stratum at approximately 13m depth. Bedrock level was generally encountered at approximately 22m to 35m below ground level. The ground water table was at a depth of approximately 1m below the existing ground surface level. A site boundary basement wall was constructed using a diaphragm wall retention system. The majority of the vertical loads from the building were transferred to the Kings Park Formation (KPF) bedrock through the use of foundation piles constructed by the CFA method. The CFA piles were installed from existing ground level, resulting in approximately 9m sacrificial concrete length from pile platform level to basement 3 (B3) level. The permanent column loads are such that a single CFA pile was not structurally adequate. To allow a full CFA foundation system to be adopted, an innovative design and construction approach was developed for these heavily loaded columns. This paper discusses the site technical details and the design and construction aspects required to meet the challenges offered by this project.

Nov 1, 2022

By Nagarajan. D, Raja Rajan. K, Vijayakumar. T

Major bridges crossing mighty rivers must be constructed in flowing water. Constructing the sub-structure in water has been a challenging job for contractor. Special construction techniques with marine fleets to be adopted for waterfront construction. Enabling works like temporary piling platform and cofferdam used for pile and pile cap construction. Apart from this, enabling works like load out jetty to transport the materials from land to water; temporary walkway for access of workman to work location; temporary access bridge for construction vehicles movement; temporary liners for tower crane foundation; Concrete block to act as dead man anchor for barge movements were all required by the contractor for smooth functioning of site as per construction schedule. Investment in enabling works by contractor plays a significant role on profit margin of the project and of course with utmost safety. Design of enabling works for waterfront structures involves hydrological data like afflux, bathymetry survey, current force, scour depth and wave force to be taken cautiously for safe and economic design. Type of foundation and pile/well cap top level corresponding to water levels shall influence the construction scheme. Usage of geotechnical software like Wallap and Plaxis required for enabling work design to enhance the safety of the structure. Bathymetry and soil condition play a critical role in design and construction of enabling works. Water Discharge quantity in river along with water levels like low water level, high flood level, seasonal fluctuation of water levels has a great impact on design of enabling works. Establishing enabling works for waterfront construction near to an existing bridge is an additional challenge for the contractor. Along with design, constructing the enabling works in water requires special construction methodology and sequence of work. This paper shall provide insights on overview of design and construction of enabling works for waterfront construction.

Nov 1, 2022