Search Documents

"Eastern Canadian thermal coal mined at Minto, New Brunswick, and in western Cape Breton at St. Rose, Inverness County, Nova Scotia, contains 6-8 per cent sulphur. Both coals are high volatile bituminous. types. The Minto coal averages 18 per cent ash, 7 per cent sulphur and has a Btu rating of 11,900 per lb. Pyritic sulphur accounts for 75 per cent of the total sulphur and the remainder is largely organic; the amount of sulphate sulphur is negligible. This means that in a 7 per cent sulphur coal, 2 per cent is organic and 5 per cent pyritic sulphur. Pit-head St. Rose coal contains approximately 10 per cent ash, 7 per cent sulphur and 11 ,800 Btu/lb. The distribution of sulphur is different to that of Minto coal because about 12 per cent sulphate sulphur is present. Thus, a 7 per cent sulphur coal would contain 4 per cent pyritic, 2 per cent organic and 1 per cent sulphate sulphur.The iron sulphides, pyrite and, to a lesser extent, marcassite occur over a wide size range from large sulphur balls to crack fillings, lenses, and individual crystals and framboids. Coarse-grained pyrite and sulphur balls are easily separated during washing. It is the fine grain sizes, intimately mixed with the coal constituents, that are difficult to separate. Quantimet analyses of the fine grains in coal from both localities showed that about 50 per cent were smaller than 30 micron(1).No efforts have been made to wash the Inverness coal of Nova Scotia and in 1980 washing ceased in New Brunswick. Previously, the Minto coal was processed in an antiquated jig circuit which reduced ash from the strip operation run-of-mine value of more than 20 per cent to less than 18. More effective removal of ash and sulphur could clearly be obtained. Laboratory tests on both Minto and St. Rose coal have shown that ash rejection rates of 40 to 50 per cent at yields of 70-80 per cent were possible(2), Little information on sulphur removal was available."

Jan 1, 1981

By John E. Callahan

"A stream sediment geochemical survey covering an area of 13.000 sq. km near Churchill Falls. Labrador. was conducted for Brinex (British Newfoundland Explorations Ltd.) prior to partial flooding by the Churchill Falls power project. Stream sediments (minus 80-mesh) were analyzed for Cu, Pb, Zn, Ni, Ag, Mo. U and Mn, and the heavy mineral, nonmagnetic fraction (minus 60-mesh) for Cu, Pb, Zn, Ni, Ag, Mo, Ba and Mn. A binocular examination of the concentrates for sulphides and pyrope garnet was done on the heavy mineral concentrates. The concentrates were also examined for fluorescent minerals.Two distinct areas with high trace-element values indicate the need for follow-up studies. The first is in an area of gabbro erratics containing massive and disseminated sulphides (pyrrhotite, pyrite and minor chalcopyrite) on the western edge of the survey area along the Esker Road. The second, largest area (several hundred square kilometres) is anomalous in U and Mo and associated with felsic intrusives (Red Wine Complex?), syenites. granite gneiss and sedimentary rocks (Seal Lake Group?).The binocular study showed that almost 15% of the heavy mineral concentrates contained pyrite and no other sulphides. This indicates that this technique may be worthwhile in determining the presence of sulphide minerals in stream sediments from glaciated environments. The only fluorescent mineral observed in the study was zircon."

Jan 1, 1981

By B. W. Brooks

"After an extensive period of University research and field trials, large scale reclamation of the Waite Amulet tailings discharge areas commenced in the spring of 1978. The Noranda program consists principally of sampling the complete dam to determine the vegetation potential of the various areas, addition of the required amelioration materials, and the use of good agricultural practices. This paper describes the development work that led to the establishment of the Noranda-Guelph Contract and the subsequent findings concerning the revegetation of tailings dams. Current revegetation procedures are presented. INTRODUCTIONThe Amulet Mine Ltd. was staked in 1924 and by 1930 had constructed a small 300 ton per day flotation plant. During the late twenties and early thirties, Noranda Mines Ltd. increased its equity in the company to gain a sixty percent share of this small mine. In 1933 the mine was amalgamated with another small producer, the Waite Ackerman Montgomery Mine Ltd., which was more than eighty per cent controlled by Noranda to form the Waite Amulet Mines Ltd.An interesting historical side point to the story of the Waite Ackerman Montgomery property is that a concentrator was never constructed. In fact, the first ore to go through the Horne mill of Noranda Mines Ltd., built in 1928, was not from the famous upper H and L ore bodies but custom shipments from the Waite."

Jan 1, 1981

"The Kidd Creek concentrator is situated adjacent to Highway 101, twenty-four kilometres east of the center of the city of Timmins, Ontario. Sulphide ore, received by train from the minesite twenty-nine kilometres away, is processed at a rate of twelve thousand metric tonnes per day. Saleable concentrates of copper, zinc, lead and tin are produced.The concentrator contains secondary crushing, grinding, flotation, gravity separation and concentrate handling facilities. The total concentrator manpower complement is one hundred and sixty-four which includes supervision and operating personnel. Twenty-one shift personnel are required to operate the processes involved and they occupy fifteen different operating positions in addition to that of the supervisor. These positions include:1 Central Control Operatorl Metallurgical Leader1 Dryer Control Operatorl Crusher Leader3 Copper-Lead-Zinc Flotation Circuit Operators1 Pyrite Flotation Circuit Operator1 Tin Plant Operator2 Grinding Operators1 Concentrate Operator2 Crusher Operators1 Spare Operator1 Tailings Area Operator1 Automatic Sample System Operator1 Dryer Area Helper1 Crusher Helper1 Tin Plant Helper"

Jan 1, 1981

By J. B. Hinzer, J. D. Harvey

"Noranda's Lyon Lake property in the Sturgeon Lake area of Northwestern Ontario was staked by Mattagami Lake Mines Limited in May 1969 to cover airborne Input anomalies. Subsequent ground geophysical and diamond drilling programs resulted in the disco very of the Boundary Extension, Lake and Creek ore zones. As of December 31, 1978, ore reserves were estimated at 3,945,000 tons assaying 6.53 per cent Zn, 1.24 per cent Cu, 0.63 per cent Pb, 3.42 oz/ton Ag and 0.010 oz/ton Au.These deposits are hosted within the South Sturgeon Lake volcanic pile of Archean age, which consists of several cycles of basic intermediate and felsic volcanic materials overlain by a sedimentary iron formation and built upon a plutonic base (Franklin , ' 1975). The top 50 m of the second felsic cycle, according to mine terminolo gy, contains the mineralization within Quartzphenocryst- bearing felsic lapilli tuff and underlying thin discontinuous graphitic sediments and altered coarse pyroclastics. The basal andesitic member of the overlying cycle forms the hanging wall to the ore deposits.Although there is no alteration pipe below the deposits, the coarse footwall rocks are permeated by chlorite, garnet, carbonate, iron sulphide and magnetitie-bearing veins intensifying from west to east.Immediate host rocks are alkali depleted and MnO, FeO, Zn and Cu enriched compared to Goodwin's (1972) average Archean rhyolites. Bedded pyrite-pyrrhotite-chalcopyrite lenses with sphalerite-rich tops are underlain by weakly developed stringer mineralization.Traversing eastward from the Lake Zone to the Creek Zone and toward the Sturgeon Lake Mine deposit, more rapid facies changes, more pronounced chloritic and carbonate alteration, the presence ofgarnets, greater MnO, FeO, CaO and Ag abundances, and increasing Zn/Cu and MnO/FeO ratios are apparent."

Jan 1, 1981

By H. W. King

"Cryogenic engineering is concerned with components and machines which operate for long periods of time at temperatures within a few degrees of absolute zero. The absence of a ductile-brittle transition is thus the prime component of the specification for a suitable low-temperature alloy. The word "" cryo"" means ""frost-forming"" , and this leads to the second component of the alloy specification, which is resistance to corrosion in humid atmospheres. Further, although most early applications of low-temperature alloys were limited to the storage or transportation of liquified gases, an increasing proportion of alternative energy storage and conversion technologies are being based on the availability of high-field superconducting solenoids. The third basic component of the specification for a low-temperature alloy is thus the absence of a low-temperature ferromagnetic transition.Although the firs t two of these components of the specification can be met by using austenitic stainless steels, many of these supposedly "" non-magnetic"" alloys have been found to undergo martensitic transformations to ferromagnetic phases at very low temperatures. In addition, steels which remain structurally stable may still exhibit other magnetic transitions, e.g. to antiferromagnetic or superparamagnetic states. The successful application of these alloys in cryogenic engineering has thus required an initial basic study of the types of magnetic transition that can occur in such concentrated solid solutions, followed by a more applied study directed at an alloy formulation which will induce beneficial magnetic states at low temperatures."

Jan 1, 1981

By N. Dufresne

"The evolution of mining methods at Brunswick Mining and Smelting shows that, in the case of a large deposit, technology must adapt itself to changing conditions. As problems are encountered, management must modify their approach if they hope to meet production quotas. This search for new and better ways started with the opening of the No. 12 orebody and is still going on today.From large-scale open stoping, the Brunswick Mining and Smelting operation went to transversal cut-and-fill, then to longitudinal cut-and-fill, which is the main mining method now employed. However, to solve certain problems experimenting with Avoca methods was initiated. Rebar grouting and prepinning have also made significant contributions toward securing relatively poor ground in the hanging wall and holding badly fractured backs in wide stoping areas. Introduction In 1952, M.J. Boylen had incorporated Brunswick Mining and Smelting Corporation Limited to develop his recently found No.6 and No. 12 orebodies near Bathurst, New Brunswick. Between 1953 and 1957, St. Joseph Lead Company was brought in to try and initiate mining . During those years, St. Joseph Lead sunk two shafts at No. 12-No. 1 to 425 feet below surface and No.2 to 982 feet. They also developed the 200 and 350 levels to sample the ore at depth and operated a 100-tpd pilot plant at the No.6 mine. However, due to low recoveries and depressed metal prices. the project was shut down in 1957.A group including M.J. Boylen. K.C. Irving. Maritime Mining Corporation and Patino Corporation reacquired the property from St. Joseph Lead Company in 1961. New financing was arranged involving La Societe Generale des Minerais, S.A . of Belgium and Engineering Consultants Limited of Saint John. New Brunswick. During the years 1962 and 1963, construction of surface and underground facilities progressed rapidly."

Jan 1, 1981

By D. A. Trotter, G. J. Goddard

"This paper describes a method of deciding on various design parameters for a sublevel caving layout. Layout design curves are obtained from the output of a computer optimization program. The program uses mathematical relationships derived from the theory of gravity flow of material to optimize the large number of interdependent design variables which are involved.IntroductionIn the design of an efficient sublevel caving mining system, a large number of interrelated variables need to be considered. Although many papers discuss individual variables, very little exists in the literature to show how these variables interact to achieve optimum results. This can lead to trial and error in sublevel caving design, which can prove costly, particularly because sublevel caving is a mining method which requires integration with sublevels above and below. With no pillars being left, experimental stopes cannot be isolated for study. Unfortunately, the complexity of layout design and the costs associated with trial and error have caused many planning engineers to choose more tried and tested mining methods.Sublevel caving works best to extract low-value ore surrounded by incompetent rock. All phases of the mining method can be highly mechanized, allowing low operating costs and high production rates. Good safety records are achieved, as workers are always in 'good' ground and the method is regular, making it comparable to an industrial process."

Jan 1, 1981

By Craig H. B. Leitch

"In describing the alteration of porphyry systems, the term ""secondary K-feldspar"" appears to be an oversimplification. A better term would be ""alkali feldspar"" alteration, because in actual fact the replacement feldspars show gradational changes from an albite, which is important in some systems, to an alkali feldspar containing minor orthoclase molecule, to true orthoclase.There are several textural varieties of secondary alkali feldspar present in the porphyry systems studied from British Columbia, Australia and New Zealand. These include, in apparent increasing order of alteration intensity: clear albite (An10); patchwork albite (Ab5-10); chessboard albite (An0-10) "" irregular albite "" (An0Ab100 to Ab90r10); untwinned "" anoralbite"" (Ab90Or-Ab70Or30); and orthoclase (Ab440Or60-Or100)·The exploration significance of these varieties of alkali feldspar is that their gradation in composition, from sodic to potassic, may be linked to a corresponding increase in intensity of alteration. Thus, there is a tendency for more sodic alteration feldspars to characterize weak, sub-economic deposits, or the fringe zones of stronger deposits; the more potassic alteration feldspars may provide an exploration vector toward more highly mineralized zones."

Jan 1, 1981

By J. R. Shore, F. G. M. Gillett, E. J. Zickar

"The addition of fines to rod mill feed has been employed at Inco Metals' Frood-Stobie Mill since 1973. The fines, which act as a ""lubricant"", causes an increase in the pulp fluidity and assists the flow of feed through the rod mill. Fines addition was one of the main factors which led to improved rod mill performance and the elimination of rod mill tangles.This paper outlines the testwork performed in evaluating the addition of fines, and summarizes the beneficial effects on rod mill grinding efficiency, throughput rates, power consumption and noise level. INTRODUCTIONFrood-Stobie Mill is situated within the Frood-Stobie mining complex, on the southern rim of the Sudbury Basin. The Mill commenced operations in November, 1967, and has since processed in excess of sixty-five million tons of ore. Minus 8-inch ore is delivered to the Mill's coarse ore bin by two surface conveyor belts from the Frood and Stobie Mines, while Little Stobie ore is transferred by underground conveyor and hoisted directly into the coarse ore bin a long with additional Stobie Mine ore."

Jan 1, 1981

By Julian Boldy

"A review of lI5 significant volcanogenic massive sulphide discoveries in the Canadian Precambrian during the past 65 years reveals that only 7% resulted from surface exploration methods aimed at depths below the effective reach of current geotechnical systems. This has been due to the relative ease of shallow discovery, resulting in the harvesting of ore deposits within 100 m of surface. This surficial layer has been more or less effectively supersaturated by routine exploration. In view of the fact that a mining district's metal content is not likely to be confined to a surficial layer, the time has come to explore the vertical dimension, prospecting for ore at depths in excess of 150 m in productive districts.Essential to this task is an understanding of the Precambrian volcanogenic ore deposit model. The deposits generally have .a tendency to be associated with the terminal phases of felsic volcanism, and to be located along certain time-stratigraphic horizons, marked by the products of volcanic exhalation. The significant massive sulphide deposits are discrete entities, ranging from the top 5% of deposits greater than 45 million tonnes in size, with a surface area of 0.30 km2, to median-sized deposits greater than 1.2 million tonnes in size with a surface area of 0.02 km2. These significant economic ore deposits range in value from $5.5 billion for the top 5% of deposits to $125 million for median-sized deposits. In terms of their frequency of occurrence, the former group has a 4% distribution and the median-sized deposits have a 15% distribution.An historical review of many of the principal Precambrian mining districts, such as Noranda and Flin Flon, shows that major tonnages are usually discovered during the initial phase of application of each new geotechnical search system, until carried to its ultimate limit of effective depth penetration. With the exception of the Noranda district, the mean depth of ore discovery in the other districts is still generally confined to within 50 m of surface.Targeting deep ore is difficult. One effective prospecting method is the detection of fracture-controlled mercury leakage haloes in outcrop (or core) above and peripheral to blind deposits. This technique has proved to be a useful pathfinder, and focuses attention on deposits buried at depths in excess of 700 m in some instances. Down-hole EM systems also promise to be effective in locating deposits previously bypassed by drilling. In addition, trend surface analysis programs of trace element geochemistry should be used as an aid to targeting ore by directing exploratory drilling along the plane of ore-hosting stratigraphy.By definition, mining districts have a proven ""favourability"" for the occurrence of ore. Discovery probabilities in these districts will be considerably enhanced if future search efforts are concentrated below a depth of 150 m, and more use is made of ""deep"" ore search systems coupled with sound geological reasoning. Deep drilling programs to a depth of800 m should initially be designed to search for the top 25% of deposits greater than 3.3 million tonnes in size, with a surface area of0.05 kmt. :a value of$310 million and a 12% frequency of occurrence; This can be accomplished for an over-all cost approximating $40,000 per drill hole. If the search depth is limited to 400 m, the over-all cost of each drill hole is $20,000, equivalent to expenditures routinely allocated to grassroots exploration drilling in the remote greenstone belts of the Precambrian. Depending on a company's objective, prospecting for deep ore offers a stimulating challange - though risky, it has its rewards."

Jan 1, 1981

By J. F. Shirley

"Very seldom, if ever, is a molybdenite by-product plant operated exactly the way the process design engineer visualizes it. The best thing the design engineer can do is provide a sound, basic circuit with enough room and flexibility in order that the operating staff can make the necessary modi fi cations to optimize the process. The plant, with minor modifications, should be capable of handling more than one process. This is especially true when the client is having the plant designed for a new process.The writer would like to propose the following ten ""rules-of thumb"" for designing by-product molybdenite plants where the molybdenite is floated out of a copper concentrate. The term rules-of-thumb is used, because there are probably valid reasons for not using one or more of them in a particular plant design. In fact it was 1980 before the writer was all owed to start up a plant where all of these rules were honored in the plant design. This was after 19 years of experience in the design of molybdenite by-product processes and plants. The main reasons for not following the rules are available capital, available space, and the client's experiences based on pilot plant and laboratory test results."

Jan 1, 1981

By Donald E. Archibald, Gerald A. Allcott

"Noranda's Heath Steele Mine is located 35 miles north of Newcastle in northern New Brunswick. Blasthole open stoping with partial delayed filling is the major mining method in use. The selection of stope and pillar dimensions to ensure mine stability was originally subjective. This paper describes the progress made in attempting to rationalize design.One major feature is the fracture pattern. The main orebody now being mined, the B zone, has undergone five periods of folding and each period of folding developed a family of fracture planes which are axial planar to that particular fold pattern.The other major features considered are the calculated increase in stress due to mining and depth and its relationship to measured strain. Experience has shown that ground problems affecting production have usually originated in rib pillars. Field observations of ground deterioration and multi-wire extensometer measurements of strain are tabulated together chronologically for each pillar.A factor representing stress and a common plane of weakness are identified. Graphical analysis is used to determine the effect of the plane of weakness on a typical stress/strain curve and provides a base for the design of pillars."

Jan 1, 1981

By G. M. Ritcey, A. W. Ashbrook

"This paper summarizes the optimum leach conditions for each Of several cobalt-containing arsenical feed materials, describes the solution treatment prior to purification of cobalt recovery, and discusses the plant operation on one feed as well as the treatment of effluents.IntroductionDuring the period 1962-1964, when the demand for uranium was low, Eldorado Mining and Refining Limited (Eldorado Nuclear Limited) made a decision to undertake a three-year diversification program. One area chosen in this program was that concerned with the processing of cobalt-nickel materials. Many such materials were evaluated over the three-year period, ranging from tailings, residues, ores, concentrates and speiss to metal scrap. Cobalt feed materials, on which much of the effort was concentrated, were those containing arsenic together with other metals such as silver, copper, nickel and iron. This paper describes the treatment of arsenic-bearing feed materials (ranging from 0.3 to 570/0 As) and the subsequent purification stages required before the separation and recovery of high-purity cobalt. Because of the current interest in treating cobalt ores, it seemed appropriate that the information on the treatment of various cobalt feeds should now be made available . Although a large amount of data were generated during the research and process development program, a complete scientific correlation and understanding could not be achieved. Nevertheless, the data may provide a guide to others involved in processing not only cobalt, but other arsenical ores."

Jan 1, 1981

By J. M. Skeaff

"The main solution, ore and residue pulp streams in the Rio Algom Quirke I uranium mill at Elliot Lake have been sampled and analyzed for radium-226. Analysis of the ore and leached residues indicates that Ra-226 dissolves and precipitates within the first pachuca tank. A maximum of approximately 0.2% of the Ra-226 in the ore remains in solution during leaching.IntroductionConcern over the acid drainage and radionuclide dissolution problems associated with uranium tailings disposal sites in Canada has prompted investigation into methods for improving current uranium processing practice.Present commercial practice usually involves leaching of the uranium ore with sulphuric acid, ion-exchange separation of the uranyl sulphate complex from the leach liquor and"" precipitation of the uranium as yellowcake. Daughter products of U-238, such as Th-230, Pb-21O and Ra-226 remain with the tailings and undergo long-term dissolution.Table I summarizes the probable behaviour of the radionuclides during milling. The concern here is with Ra-226, because it will deposit in the bones if ingested and is ""thus considered a serious health hazard(1), Similarly, Po-218 and Bi-214, which are daughter products of Rn-222, can be retained in the lungs and are considered to be the principal sources of radiation dosage(2) arising from the inhalation of Rn-222. Previous investigations(3-9l indicate or imply that Ra-226 undergoes redistribution during milling. However, detailed published information on the behaviour of Ra-226 in the uranium milling process appears to be lacking. A knowledge of the behaviour of Ra-226 in uranium mills, particularly during leaching, could lead to improved methods for its control.This paper reports the occurrence of Ra-226 in the Rio Algom mill. The main objectives of the study were to determine (1) the distribution of Ra-226 within the solids, (2) at what point, and how rapidly, redistribution occurs and (3) whether there are high concentrations of Ra-226 in solution."

Jan 1, 1981

By D. A. Whitley, R. P. Carone

"Shaft sinking by blind shaft drilling offers the mining industry a different approach to shaft construction. Benefits of blind drilling include less construction time and fewer safety problems while being economically competitive with conventional sinking methods under certain conditions in soft water-bearing formations.Technology and equipment are available today to drill blind shafts up to 20 feet in diameter and over 3,000 feet deep. This is an extension of proven techniques developed by private industry. To drill a 20-foot-diameter hole requires a specially manufactured hydraulic drill unit with a rated hoist of 2 million pounds and 500,000 ft/lb of torque.This brief paper will discuss the following aspects of blind shaft drilling:• benefits;• equipment f or drilling;• circulation methods;• circulation rates;• shaft alignment; and• progress rates to be expected.IntroductionShaft sinking by blind shaft drilling offers the mining industry an improved alternative method for shaft construction. The drilling of 20-foot -diameter shafts to depth s in excess of 3,000 feet can be done by utilizing equipment specifically designed and manufactured for this purpose. This equipment is a distant cousin, at best, to standard oil well drilling rigs. The actual configuration of these drilling machines will be discussed in a following section.To most people, the drilling of mine shafts may seem to be a new or at least recent technology. However, as early as the I920s, German and Dutch miners were drilling 24-foot diameter shafts for coal mines. What led ""miners to resort to drilling were ground conditions that still plague conventional shaft sinkers today: soft , water-bearing formations. The major drawback to these early attempts was a low penetration rate due to poor bit cleaning. This, however, was not the end of early shaft drilling activity. From 1936 to 1950, a number of mine shafts were drilled by the calyx or coring method. This method employs a bit with a large bore down the center. As it drills, it cuts a core. When 5 to 10 feet have been drilled, the core is removed. The disadvantages of this method were the time and work involved in breaking the core free, and it was inadequate in soft water-bearing ground."

Jan 1, 1981

By D. Marotte, M. David

"A new exploration procedure is proposed for volcanogenic massive sulphide deposits of the Abitibi belt. ""Samples"" of acidic volcanic rocks (Si02 > 60%) were compiled from the literature. From the 574 samples collected, 322 were used in each of a number of experiments. Forward inclusion linear discriminant analysis performed on the untransformed geochemical data shows a general depletion in Na20 and CaO along with an enrichment in MgO for a ""proximal"" group of samples relative to a ""distal"" one. The percentage of misclassified samples reaches 20% to 30%, but test sets shows good stability.The exploration procedure was applied to the Normetal deposit, where the authors took 160 samples during the summer of 1977. It quickly leads to the definition of targets for more detailed exploration together with a good recognition of the old known deposit.IntroductionVolcanogenic massive sulphide deposits in the Abitibi belt (Quebec) are mainly found in rhyolites or acidic pyroclastics in the uppermost portion of a calc-alkaline volcanic series (Descarreaux, 1972). The deposits are thought to have formed syngenetically by the action of volcanic hydrothermal exhalations during the waning episode of a felsic volcanic cycle (De Rosen Spence, 1976). Alteration pipes of disseminated sulphides are commonly present. Metal deposition from hot springs, initiating convection cells in a submarine environment, may have been the dominant process in ore formation (De Rosen Spence, 1976)."

Jan 1, 1981

By Sune Eriksson, Stig Peterssonsune, Christer Fridfeldt

"Boliden Metal Corporation has developed a technique to treat complex copper concentrates containing large amounts of lead, zinc, arsenic, antimony and bismuth which cannot be treated in conventional smelters due to the impurities.Tests were carried out to treat such complex copper concentrates in the TBRC. They were performed in a pilot-plant TBRC with charges of 5 tons. These tests resulted in a new method to treat complex copper raw materials and produce a blister copper low in impurities. The background and data from the test work are presented as well as a flowsheet for a full-scale process.IntroductionThe Ronnskar Works is situated on the coast of the Gulf of Bothnia, 40 miles east of the Boliden Mine. Smelting began at Ronnskar in 1930 to process the complex ore extracted from the Boliden Mine. The Ronnskar Works has subsequently developed into a relatively integrated smelting plant.Copper and lead sulphide concentrates from Boliden's own mines as well as purchased copper raw materials are processed. The main products are refined copper and lead, but full utilization of the raw material also yields other metals and some metallurgical and chemical by-products. The products include gold, silver, zinc clinker, white arsenic, arsenic salts and arsenic metal , selenium and selenium compounds, nickel sulphates, sulphuric acid and liquid sulphur dioxide."

Jan 1, 1981

By Robert B. Parsons

"First down and four to go. In the game Of football, this is not a bad position to be in. However, in this game of political football, it means that there is still a long way to go. The government in Ottawa has concluded an important agreement with one producing province, and now has at least four more provinces to deal with-B. c., Saskatchewan, Nova Scotia and Newfoundland.On September 1, 1981, the federal and Alberta governments took a significant step forward in formulating an oil and gas policy for Alberta and the rest of Canada on signing a comprehensive five-year agreement that covers taxes, prices, incentives and other fiscal matters related to the production and marketing of oil and gas.This month, Tax Notes examines the main features of the agreement, and offers some eye-opening observations of what the new accord could mean for the future of the Canadian petroleum sector in particular and Canadian business in general."

Jan 1, 1981

By D. L. Marchioni

"The detection and quantification of the degree of weathering is an important aspect of coal exploration and mining. Tests for weathering which are suitable for the exploration camp should be fast, simple, and require minimal equipment and operator expertise. In this study, two tests which fulfill these requirements were evaluated using samples of Western Canadian coals. These tests, one based on the pH of a coal slurry and the other on the flotation of coal in a water/diesel oil mixture, do not appear to give consistent results and are not recommended as ideal weathering parameters.IntroductionThe weathering of coal results in a deterioration of those properties which render it suitable for use in industrial processes. Consequently, the detection and quantification of the degree of weathering is an important aspect of exploration and mining. Frequently, decisions related to the depth of the weathered zone must be made at the exploration camp and, therefore, tests for weathering which are fast, and require relatively inexpensive and portable equipment and minimal operator experience, would be very useful. The aim of the study reported here was to evaluate two tests used by U. S. Steel Corp. to detect coal weathering and which satisfy the requirements for use in an exploration camp. The study is a continuation of a more extensive examination of the detection of coal weathering by various methods, reported elsewhere (Marchioni, in press)."

Jan 1, 1981