Search Documents

By A. F. Gregory

"AbstractA resumé of aerial radiation survey studies performed by and for Eldorado Mining and Refining, Limited, since 1943 is presented. Flight tests were initiated in 1947 and were followed .by intensified use and study of Geiger counters and other radiation detectors. Development of an aerial scintillation counter began in 1948, but •a sensitive large crystal unit was not available for exploration purposes until 1950. Modifications of this unit have been used in all subsequent surveys.For the Eldorado detector, several limiting conditions were established for successful radioactivity detection, the most important being that natural vein exposures can only be assuredly detected .at distances less than 150 feet. Sedimentary and pegmatitic radioactive occurrences can be detected at much greater distances. A helicopter investigation technique appears to •have •a useful prospecting potential.IntroductionAerial radiation surveys were first proposed in the early 1940's. However, it was not until 1949 that airborne detectors were extensively used in the search for radioactive minerals. Eldorado has flown about 50,000 miles of exploration flights, exclusive of tests, using a variety of •detectors and aircraft. Considerable data have •been gathered for .the evaluation of the several techniques employed. Much of the early work was performed with the co-operation of the National Research Council of Canada ( 1). More recent work was done in conjunction with the Commercial Products Division of Atomic Energy of Canada, Limited. The Development Department of this latter corporation designed and built the scintillation counter used in recent Eldorado surveys."

Jan 1, 1955

By K. K. Mamyrbayeva, G. Z. Guseinova, V. A. Luganov

This paper presents the results of theoretical and technological studies on leaching ore of Bozshakol deposit. The major oxidized copper mineral of Bozshakol ore is atacamite, and the content of malachite, azurite, cuprite, copper sulfide minerals is insignificant. The chemical composition of the test sample, with mass, %: 0.9 Cu; 55.00 SiO2; 22.40 AI2O3; 9.00 Fe2O3; 2.24 CaO; 3.56 MgO. Technological studies on leaching the ore were carried out with sulfuric acid 5, 15, 25 and 50 g/dm3 in one and multistage (up to 4 stages) countercurrents. Size of ore 1 mm, the ratio S : L 1: 4. It was found that with increasing of acid concentration from 5 to 50 at one-mode leaching the copper extraction reaches 55 %. At multistage leaching the copper recovery reaches 73 %, a productive solution containing g/dm3: Cu - 4; Fe – 1.2; Al – 1.1 at a pH of 2.8. When leaching the cinders obtained by ore roasting in an atmosphere with limited value of oxygen, with increasing of the roasting temperature from 650 up to 750 °? the extraction of copper from the Bozshakol ores reduced from 31.5% down to 24.4%. The rate of filtration is markedly increased compared with the crude ore. When leaching the cinders obtained by roasting in a nitrogen atmosphere a marked increase up to 87.2-88 % of copper extraction from Bozshakol ores is observed. As an extractant for the extraction of copper from the pregnant solution used LIX984N extractant in kerosene. On the basis of the calculations it was built extraction isotherm and modeled processes of copper recovery with the circuit 2E + 1P, allowing up to 93 and 96% extraction. The through extraction of copper from the ore in the electrolyte was 67 %. Technology is recommended for semi test.

Jan 1, 2016

By J. D. T. Steyl

"This paper presents a phenomenological model of the rate of iron(III) precipitation in batch and continuous autoclaves at medium temperature operating conditions. The rate expressions are based on information obtained from the literature and experimentation at low and high pulp densities. Special allowance is made for the formation of surface nuclei, which appears to be promoted at a higher iron(III) precipitate surface area, especially in suspensions of lower terminal acidity. This leads to the formation of secondary particulates and provides the required link to simulate high pulp density leaching-precipitation systems, using low pulp density batch precipitation data. In particular, the model allows direct application of the simulation to the autoclave oxidation of iron-containing copper sulfide concentrates and provides a good estimation of the relative precipitation rate of hematite, the preferred product, compared to hydronium jarosite. Some interesting mechanistic understandings of iron(III) precipitation in autoclaves are further elucidated.INTRODUCTIONThe objective of this work is to describe the rate of iron(III) precipitation and the relative amounts of hematite compared to hydronium jarosite precipitation during batch and continuous chalcopyrite oxidation under medium temperature (MT) (~130 to 160ºC) autoclave conditions. Published information has not yet revealed sufficient mechanistic insights about this sparingly soluble salt system under these conditions. The rate expressions in this paper are based in part on current literature information, supplemented by qualitative experimental observation at low pulp density conditions, in particular the high-resolution backscatter electron (BSE) images and particle size distributions (PSDs) of the precipitates. A summary of this work and insights from the literature are presented first, after which the behaviour of iron(III) in high pulp density leaching systems is used to derive a phenomenological expression of the effect of existing iron(III) precipitate surface area on the precipitation rate. The overall regression encapsulates all the experimental results, i.e., those obtained in both batch and continuous autoclave configurations (Steyl, 2012a)."

Jan 1, 2012

By A. Montini, M. H. Moys

"A conductivity probe mounted in the shell of the mill has been used to measure the behaviour of the load in the mill as a function of operating variables. It was found that certain properties of the conductivity signal correlate strongly with the per cent solids of the slurry passing through the mill; in particular the angular location ?D of the shoulder of the load is an increasing function of the per cent solids. A method for measuring the viscosity of the pulp discharging from the mill has also been developed. The use of the measurements in mill control is illustrated by simulating various control strategies for open circuit milling. It is shown that the use of ?D allows very tight but imprecise control of the slurry rheology in the mill, while the use of viscosity is subject to severe limitations in speed of response. A cascade control system involving both measurements provides adequate control of slurry rheology within the mill. Applications to closed circuit milling are discussed.IntroductionMultivariable control of milling circuits continues to receive a lot of attention in the literature. Hulbert and co-workers and Niemi, et al. have described the use of Inverse Nyquist Array (INA) techniques while Herbst has recently described the use of Optimal Control. It is significant that in neither of these three projects was any variable associated with the grinding mill itself (e.g. power or properties of the mill discharge) used in the control strategy. Pauw, et al.do, however, use mill power in their multivariable peak-seeking controller for pebble-mill control. Little work has been published on the use of measurements of the properties of the slurry being discharged from grinding mills, in spite of the fact that milling efficiency is known to be strongly affected by slurry rheology».Moys has recently developed a technique for measuring the dynamic behaviour of the load in the grinding mill. This method involves the monitoring of the response of a conductivity probe mounted in the shell of the mill which gives a measurement of the orientation of the load inside the mill. It was found that the load behaviour was strongly influenced by slurry rheology. In this project a technique was also developed for the measurement of the viscosity of the slurry in the mill discharge. It was, thus, decided that it would be worth investigating the use of these measurements in mill control schemes since direct control of the slurry rheology in the mill must inevitably increase the efficiency and productivity of the grinding circuit as a whole.This will be done by using the dynamic responses measured by Moys and Montini to simulate the behaviour of an open circuit ball mill. While the control of open circuit mills is of little interest, this simulation provides a simple but powerful demonstration of the advantage provided by these measurements, advantages which should apply to closed circuit operation of any mill type (including autogenous milling). Investigations into multivariable control of a closed circuit ball mill are currently nearing completion and will be published soon."

Jan 1, 1987

By M. E. Coleman, G. Money

Pneumatic Conveying and Process Injection Technologies have been implemented in the metals markets for the last 40 years and have considerably improved the productivity and the performance of many processes. There have been many steps forward in handling technology and this paper seeks to consider those now offered by Clyde Materials Handling who as an established customer-driven solutions provider has turned its attention to supporting the Metals Market. Clyde seeks to utilise its knowledge, expertise and technologies to transform the production processes of its customers, who operate in the ferrous and non-ferrous metals industries.

Jan 1, 2008

By G. F. Flaherty

THE property of Tashota Goldfields, Limited, in the Lake Nipigon area, Ontario, is located about 4 miles west of Onaman lake and 16 miles by winter road south-southeast of Tashota station on the transcontinental line of the Canadian National railways. The mine, formerly developed to a limited extent under the name of Tashota Gold mine, has, since late in 1933, been under the management of Minefinders Limited, who, in 1935, brought it into production on a 60-ton per day basis. During the winter of 1934-35, the writer was geologist at the property. The geological structure in the immediate vicinity of the mine workings lends itself well to analysis on the basis of the mechanical principles of folding. Since structure is of prime importance in the localization of the ore-shoots and of the host shear-zones at the property, the correlation of all structural details and their mechanical interpretation forms a working hypothesis of structural control for the direction of exploration and development work. It is believed that the structural relations here set forth may be found applicable in part, or at least suggestive, in working out the relations of ore-shoots to structure in the Sturgeon River area to the south, and in the Little Long Lac area to the southeast (Figure 1).

Jan 1, 1936

By Ed Labelle, Terry Overton, Gary Bell

"LocationThe Miller Minerals lime and limestone production facility is located in the Temiskaming district of Ontario at Hailey bury on the west shore of Lake Temiskaming. Located less than 300 km from Sudbury, Timmins, Rouyn-Noranda and Val d'Or, the plant is very well situated to market products to the mining, pulp and paper, and environmental industries. Being located a few kilometres from the Trans-Canada Highway and the Ontario Northland Railway adds to transportation efficiencies.ProductsAt Miller Minerals, two principal products in various sizes are produced, which are limestone (CaC03) and quicklime (CaO).HistoryProduction of limestone products began in 1979 at this quarry site. During the 1980s, limestone products were marketed to a variety of applications for mining, forestry, environmental and agriculture applications. In 1990, the production of quicklime products began, following the commissioning of an Italian-designed vertical shaft calcining plant. During the 1990s, both quicklime and limestone products were produced to meet the customers' demands.From the quarry's conception until 1992, the operation was owned and operated by Dymond Clay Products. In 1992, it was purchased by Miller Paving Ltd. of Markham, Ontario, and became a key part of the company's industrial minerals sector of business. Other Miller interests include dolomite, cement, paving materials and waste management."

Jan 1, 2000

By José L. Carvalho

"Time-dependent swelling deformation of several shaley rock formations in Ontario is a wellknown phenomenon. In shales and mudstones with a higher salt concentration in the pore fluid than the ambient fluid, the outward gradient generates an osmotic pressure which acts as the driving force for swelling. The swelling phenomenon appears to be related to ion exchange between the rock porewater and the surrounding water.The swelling potential is expressed as the percent swelling strain that occurs per log cycle of time, in either the vertical (perpendicular to bedding) or horizontal (parallel to bedding) directions. In addition, the swelling potential is also noted to be stress dependent. In practice, therefore, the conditions required for swelling are (i) the accessibility to water, and (ii) an outward salt concentration gradient from pore fluid of the rock to the ambient fluid. The relief of in-situ rock stress during excavation serves an initiating mechanism (Lo and Micic, 2010).INTRODUCTIONTime-dependent swelling deformation of several shaley rock formations in Ontario is a well-known phenomenon. In shales and mudstones with a higher salt concentration in the pore fluid than the ambient fluid, the outward gradient generates an osmotic pressure which acts as the driving force for swelling. Swelling is also controlled by the inter-particle bonding; if the bond strength exceeds the osmotic pressure, swelling will not occur, and vice-versa. The bond strength can be reflected by the calcite content which forms cementation bond between rock particles."

Jan 1, 2015

By A. Brian Hawkins

"When pyrite oxidizes in dark grey/black, calcareous, mudrocks or in argillaceous limestones, ferrous sulfate is formed and sulfuric acid is released. The sulfuric acid combines with the calcite present in the rock and calcium sulfate (gypsum) develops. When this occurs on the outer edges of aggregate particles, the gypsum forms in the matrix hence there may be little expansion of the general material. However, when the chemical reactions occur within the rock fragments, particularly on microscopic, clayrich, laminae, the developing crystals exert a significant pressure on the host material. If the rock is medium strong to strong, the force of crystallization splits the rock along the weaker planes, facilitating the ingress of the oxidizing agents and the continuation of the chemical reactions. In addition to causing dilation/heave, some of the engineering properties of the material are changed, including the strength, Los Angeles value, water absorption etc. As a consequence material, which at the time of quarrying would be acceptable for use beneath floors or hardstandings, would no longer be considered suitable.INTRODUCTIONMudrocks accreting in aerobic environments are frequently disturbed by organisms and as a consequence there is often little sign of bedding. In contrast, sediments which have formed in anoxic environments commonly have distinct bedding planes which, because of the grain size of the accreting material, are often smooth and planar. These rocks are frequently referred to as shales, which O’Brien and Slatt (1990) define as “characterised by a finely laminated structure, which imparts a fissility approximately parallel to the bedding.” This should not be confused with rhythmic bedding where the variation in grain size results in lithological laminations or colour changes.Early geologists, in the stratigraphic naming of rocks, often used the term shale for material which is now more likely to be described as mudstone or mudrock (Hawkins and Pinches, 1992). In many contexts, the width of the bedding is an important factor, not only in determining the rock name but also in indicating the potential engineering characteristics. Until recently a shale was considered to have bedding separations of less than 20mm, i.e. the bedding was described as laminated. However, in an engineering context, EN 14689: 2003, Annex A, defines shale by specifying a bedding thickness of < 6mm; such a material would be described as thinly laminated in BS 5930:1999. Ideally the term shale should be abandoned and be replaced by fissile mudstone or fissile mudrock."

Jan 1, 2015

By M. S. King

"A simple method is proposed for determining the long-term deformation behaviour of evaporites. The theory developed can be tested by measuring the change in diameter as a function of time of a vertical mine shaft opposite evaporite strata. Ultimate shaft closures predicted by the theory agree well with those calculated with the very much more complex theory of Serata (1968), provided that sufficiently high octahedral shear strengths are used in the former.An analysis of measurements made in an isolated opening in a Saskatchewan potash mine shows that the octahedral shear strength of the surrounding potash and halite was approximately 500 psi several years after the opening was mined. This value is less than that deter-mined experimentally for halite by Serata. The same data indicate, furthermore, that the in-situ octahedral shear strength is decreasing slowly with time.The current controversy regarding the actual deformation of evaporites will only be resolved by the cooperation of potash producing companies in releasing data on the long-term deformation of their mine shafts."

Jan 1, 1971

By J. C. White

"During the early development of the Mattabi Mine in 1970, discussions with the Ontario Government revealed their policy of prohibiting, as much as possible, the development of new, isolated, single-industry townsites. Subsequently, Mattabi located its first housing in the Township of Ignace, which is situated 50 miles from the site of the mine and plant. Over 200 employees now commute 100 miles daily to and from work.This paper describes the experience gained and discusses the advantages and disadvantages of a remote townsite."

Jan 1, 1976

By R. Boom

Corus Umuiden, formerly Hoogovens, was the first steel plant in Europe after Voest to introduce oxygen steelmaking. In the decision-making process contacts with Dofasco in Canada about the production of formability steel grades were crucial. In developing oxygen (LD-) steelmaking high liquid steel output rates had to be combined with accurate process control. For ingot casting static models with input control and sampling during interrupted blowing were sufficient to deliver liquid steel within the required carbon, phosphorus, sulphur and temperature windows. Computers were introduced to perform the complicated charge calculations. Continuous casting called for strict control of composition and temperature at process end point and made predictable timing crucial. Dynamic control was introduced based upon sub lance measurements and waste gas analysis. Reliable disposable measurement sensors were developed in a concerted international action. Dissolved oxygen at blow end deteriorated the quality of low carbon aluminium killed steel grades. Blowing gases through the converter bottom improved process kinetics, resulting in lower carbon-oxygen products, yield increase and better phosphorus removal and generated new families of hybrid blowing processes. Introduction of secondary metallurgy facilities such as argon stirring stations, vacuum degassers and ladle furnaces relieved the demands for strict BOF end point control. Desulphurisation of hot metal became standard practice. In regions with scrap shortage hot metal desiliconisation followed by dephosphorisation, was introduced in the blast furnace cast house and hot metal transfer ladles. Later redundant converter vessels were used for pre-treatment, resulting in a two-stage process. The fundamentals of oxygen steelmaking are described and a vision on the future is presented.

Jan 1, 2004

1. Scope of project In South Australia, the Western Mining Corporation operates the underground copper and uranium mine Olympic Dam. The deposits concerned are enormous (approx. 570 million tons) and have been mined since 1988. At the end of 1996, Western Mining decided to increase the capacity of Olympic Dam from 85,000 t.p.a. to 200,000 t.p.a. Planning At this point, SIEMAG-GHH Mining Division was asked to carry out a study including the planning of the entire shaft hoisting operations and calculation of the investment and operating costs involved. With the assistance of Australian partners, the study was completed within a single month. The principal points of the study were as follows: ? Planning of the hoisting machinery for 1,375 tons per hour from the surge bin below ground to the discharge bunker above ground. ? Optimisation of the hoisting operation with regard to maximum availability and safety. ? Optimisation of the time schedule to minimise the financing costs of the investment. ? Statement of the investment and operating costs. ? Comparison of the technical data, design and availability of the planned machinery with reference plants. Construction of the plant Following acceptance of the study, the decision was taken within a few weeks to implement it. SIEMAG Transplan GmbH received the order to execute the entire shaft hoisting machinery on the basis of the study submitted. The decisive factors in placing the order were: ? Convincing study, adherence to schedule ? Reference to comparable plants elsewhere ? Reference with regard to availability.

May 1, 2003

By Jean Cayouette

"In 1995, Louvicourt Mine started one of the first paste backfill operations in Canada. From 500,000 tonnes in 1995, the annual paste backfill tonnage produced reached 800,000 tonnes in 1999. The maximum throughput of the surface plant (including binders) is 3,50Ot/d with a final density of 75 to 76% solids which gives a slump of 15 to 17cm. Following the start-up of the paste backfill plant, the backfill strength performance levels were well below the pilot plant’s predictions. The introduction of ferrous slag, laboratory tests on various binder ratios with or without additives, and the desliming of the tailings enabled us to optimize the mix and operation costs. Primary and secondary stopes are filled respectively with a paste containing 4.5% and 2% binders consisting of a mixture of 20% cement and 80% ferrous slag. In certain stopes, the binder ratio may vary from 2 to 7%, but always in a ratio of 80/20. Six years after start-up, or 4.5mt of paste backfill later, this paper discusses the present operation and the major changes that have occurred over the years to optimize both the operation and the paste fill quality.INTRODUCTIONLouvicourt Mine is operated by Aur Resources Inc. which owns 30% of the shares. Its partners are Novicourt Inc. (45%, subsidiary of Noranda Inc.) and Teck Corporation (25%). The mine is located in the north-west part of Quebec, about 600 km north of Montreal and about 25 km east of Val d’Or. The mine commenced commercial production in July 1994."

Jan 1, 2002

By Alan D. Brown

"Diesel-electric trucks are those that have some portion of the convention-al mechanical drive train replaced by electrical components. As larger and more powerful diesel engines appeared, the development of mechanical transmissions and related drive components failed to keep pace, and electrical generators and drive motors therefore came into use as an efficient means of transferring the mechanical energy of the engine to the driving wheels of the vehicle.The Berkeley Pit has been a major testing ground for the evolution of this type of truck. We now operate a haulage fleet consisting of conventional diesel trucks and two different types of diesel-electric trucks. There-fore, we have been able to obtain an interesting comparison of costs and performances between these three types of haulage units.In all phases of operation, the diesel-electric truck commands a favourable advantage over the conventional diesel truck, and represents a more efficient and less costly means of haulage. Nearly all manufacturers of heavy-duty trucks are now building, or have plans to build, such a truck."

Jan 1, 1966

By S. Kelebek, B. Ingram, C. Gibson, T. MacNeil, M. Aghamirian

"The beneficiation and upgrading of pyrochlore from its ores is carried out through flotation. In industrial practice, upgrading is conducted in a two-stage flotation process in which pyrochlore flotation is carried out after gangue mineral pre-flotation (carbonate, silicate, sulphide or phosphate reverse flotation). In this study, the flotation of pyrochlore from a low grade carbonatite ore was performed at the laboratory scale following a two-stage flotation process in which carbonate minerals were floated in advance of niobium minerals. In parallel, a simplified flotation process was developed in which pyrochlore was floated directly from gangue minerals at increasingly acidic pH. Laboratory results indicated that both two-stage and direct flotation provided similar results in terms of niobium grade-recovery. Based on these results, a large scale, integrated pilot plant was conducted using a direct flotation flowsheet. While the elimination of reverse gangue flotation resulted in flowsheet simplification, the dissolution of carbonate minerals and the subsequent effect of dissolved cations on the floatability of pyrochlore added an element of complexity. A comparison of results from locked-cycle laboratory testing and pilot plant testing highlights the challenges of scaling up a complex flowsheet. A case is made for the direct flotation process and the key parameters to achieving success in large scale direct flotation of pyrochlore are discussed.INTRODUCTIONPyrochlore (Ca,Na)2Nb2O6(OH,F) is a niobium bearing mineral which has been the primary global source of niobium since the first pyrochlore mine commenced operations in the late 1960s (Gibson et al., 2015a). Preceding the discovery and development of high grade pyrochlore deposits in North and South America, the majority of global niobium supply came from gravity concentration operations of columbite (Fe,Mn)Nb2O6, across Africa (Perrault and Manker, 1981)."

Jan 1, 2016

By J. O. Yeboah, V. Boakye, P. A. Bepswa, M. Lombard, G. Nutor

The comminution circuit at Tarkwa Gold Mine was commissioned as a Single Stage SAG mill operated in closed circuit with hydrocyclones designed to process 4Mtpa. The circuit was later expanded by adding a secondary ball mill in closed circuit with hydrocyclones with a view to treat 12Mtpa. The change in the circuit configuration and assigning the low aspect ratio SAG mill for primary grinding application makes the Tarkwa experience unique in terms the optimisation strategy and operating philosophy. This paper reports the findings from a series of surveys performed on this plant. The surveys reported include data obtained when the SAG mill was operated as a single stage mill in closed circuit with hydrocyclones and also SABC mode under two different feed conditions. The differences in operating philosophy between the initial single stage SAG circuit and the current SAG/Ball mill circuit are discussed.

Jan 1, 2012

By H. G. Harper, R. C. Hart

"The Mississagi quartzite is the basal formation of the Quirke Lake trough. As it is traced around the rim, a gradual change in dip is observed, as follows:Northwest corner 50 degrees south.Algom Quirke mine 34 degrees south.Quirke Lake 25 degrees south.Whiskey Lake 22 degrees west.Pecors Lake 25 degrees north.Algom Nordic mine 18 degrees north.Elliot Lake 11 degrees north.Pistol Lake 5-7 degrees west.Thus the apparent synclinal axis is a curving east-west line lying closer to the north limb than to the south. The axis appears to plunge west at about 5 degrees.The Huronian sediments lie on a basement of granites, gabbros, and volcanics. Diamond drill evidence indicates that this basement has a surface of peneplanation, and that the areas of soft basic rock have a smoother topography than the granite. For the most part the orebodies at the Quirke and Nordic mines overlie a basement of soft basic rock.The Mississagi formation is the host rock of the deposits, and its primary structures are suggestive of the conditions under which the conglomerate beds were deposited. Cross-bedding is common, although normal bedding varies from thick to thin to essentially lacking. Grain gradation is not common. Where coarse and fine grains occur together, the coarse tend to be more rounded than the fine. These features are characteristic of shallow-water deposits, laid down above the lower limit of wave action. Therefore, the quartz-pebble conglomerates probably represent ancient water courses, bays, beaches, and bars.The causes governing the creation of the trough can only be conjectured, but there is evidence that both subsidence and compressive stresses played active roles. Drag-folds in argillite beds near Whiskey Lake indicate compressive stress. On the other hand, gentle crumpling in thin-bedded limestones on Quirke Lake is probably due to pre-induration slumping and folding. If strong compression had been widespread within the trough, one would expect drag-folding and shearing of the incompetent beds to be more general. Two large-scale, fold-like structures were mapped by Collins, but their axes do not parallel the trough axis, and they are therefore not related to the major structure."

Jan 1, 1949

By Y. Masuda, Y. Nakamura, K. Haraguchi, A. Taniguchi, K. Arita

Availability of the elements originating from steelmaking slag for various marine phytoplankters including purely cultured strains and natural populations was tested in land and shipboard laboratories. The results obtained demonstrate that, although their solubility was not uniform among different slags, dissolved iron, silicate and phosphate from the slag stimulate phytoplankton growth. No negative effect of the slag addition on their growth was observed at lower dose, e.g. less than 200 mg/l. Since most coastal waters are the hypernitrogenous environment due to anthropogenic load of ammonium, the slag can be an ideal source of silicate and phosphate, which restore the hyper-nitrogenous condition into truly eutrophic condition with balanced Redfield ratio. In so-called HNLC (high-nitrate low-chlorophyll) oceanic areas such as the Southern Ocean and the subarctic North Pacific, where iron is almost only limiting factor of the phytoplankton growth, the slag could also be a source of iron and enhance CO2 fixation by phytoplankton photosynthesis. (Key words: carbon deposition in deep-sea, marine environmental remediation, phytoplankton, slag as a source of iron, phosphate and silicate.)

Jan 1, 2004

By M. Askari, A. Ahmadi

"This study was conducted to establish the possible application of bioleaching in the pilot scale to recover valuable metals from the sulfidic tailings of Golgohar Iron Mine (Kerman, Iran). Using bioleaching processes, solvent extraction and sulfide precipitation recovery of valuable metals including, copper, cobalt and nickel from the tailing was investigated. The results showed that the optimum pH and temperature conditions relative to the bioleaching step was 1.5 and 45°C. The extraction of the metals from the low grade polymetal resource with complex mineralogy is very important from economic, environmental and technical point of views. Moreover, the proposed method has some advantages from energy saving, tailing management and creating added value from waste materials aspects.INTRODUCTION The growing demand for base metals and strategic such as: copper, nickel and cobalt as well as high-grade resource depletion has caused them, the mining industry to extract metals from low-grade resources and driven by complex mineralogy (Xie et al., 2005). Economic extraction of metals with low grade sources requires low-cost and efficient processing methods. A source with enormous potential for metals in future, secondary sources, such as: tailings mineral industries which the lack of appropriate technology and the high cost of processing weren't recoverable with previous procedures in the past. But it is possible that with develop new and efficient technologies have the economic exploitation ability. Recovery of metals from tailings resources is very important not only in terms of precious metals but also in terms of reducing environmental problems (due to heavy metals). The metals of copper, nickel and cobalt are mainly like sulfide compounds in the nature, usually for their recovery, first they make ore with flotation method to obtain the sulfide concentrate that containing valuable metals. then for the metal production, it will be melt and purification. Due to the environmental aspects, technical problems in the recovery of base metals from low grade ore and mixes, the presence of small reserves, in the past three decades they pay much attention to the use of hydrometallurgical processes for the recovery of base metals from these resources. These processes are classified according to the solver agent to leaching sulfates, chlorides, nitrates and amines (Hackl, 1995). Early, chloride leaching under oxidation condition in acidic or alkaline solutions was recognized the best process to produce sulfide concentrates. But then the basic processes sulfates was considered as the superior process because of being easier, a better understanding of the chemistry of leaching and recovery of base metals, especially copper from the environment easier sulfate solution with an organic solvent extraction and electro winning. The bioleaching is shown its ability on a commercial scale of low-grade sulfide minerals and ore that because of environmental reasons, the possibility of melting is not possible to them. The existing industrial base factories are based on primarily on the bioleaching and pressure leaching and recovery of cathode copper sulfate solution by extraction with organic solvents (SX) and electrowinning (EW) (Wang, 2005). Preliminary analysis has shown that valuable elements such as copper, nickel and cobalt are in the float flotation unit. Hence the plan to extract these metals from the wet tailing stream has been done."

Jan 1, 2017