Search Documents

By D. W. Rogers

Several commercial polyacrylamide flocculants most widely used in Western Canadian mineral processing plants have been analyzed chemically and compared in standardized settling tests as aids to thickening and clarification. Data are included for both dry and liquid-type flocculants. Percentages of active ingredients in these commercial products varied Widely. Performances were compared on the basis of: equal additions of active ingredients, nearly equal molecular weights and nearly equal degrees of ionic character. Based on zone settling velocities and supernatant clarities of siliceous slurries coagulated by lime additions, dry flocculants proved more economical than liquid flocculants. Using these same two criteria, the most highly anionic were more effective than either weakly anionic or non ionic polyacrylamide- type flocculants.

Jan 1, 1978

By Zoltan Hajnal

Magnetic studies have been carried out on 88 surface and 157 underground samples from the Coronation Mine area of northern Saskatchewan. The intensity of the surface samples was compared to trace element determinations from the same locality. A good correlation was found between the titaniferous constituent of the rocks and the intensity of magnetization. From the direction of the remanent magnetism, two virtual geomagnetic poles were determined -latitude 12° 54' North, longitude 158" 17' West; and latitude 23" 42' North, longitude 163° 45' West. The sulphide ore specimens showed anisotropic susceptibility characteristics. A relationship was found between the measured maximum susceptibility values of the ore specimens and the direction of the tectonic forces which are considered to have formed the structure at the Coronation mine. Introduction T HIS paper summarizes the results of a study of the magnetic properties of samples from well-known Precambrian formations. The observed data give information for an interpretation of the magnetic field conditions in Precambrian times. The high magnetic intensity values indicate the importance of the study

Jan 1, 1965

By Jan Kvinge, Aina Opsal Bakke, Yanjun Li, Jan-Ove Løland, Svein Jørgensen

"Compound casting is a very attractive approach to reduce the weight of components for some specific applications while keep both the functional and the mechanical property requirements. In this work, Al-7Si-Mg alloy /copper compound castings were produced through a low pressure die casting process. To reduce the oxide present in the interface, flux coating of the copper pipes was tested. The interface layer formed between the two alloys was investigated using Optical Microscopy (OM), Scanning Electron Microscopy (SEM) and Energy Dispersive X-ray Spectroscopy (EDS). Vickers Micro-hardness was also measured across the interface. Results showed that the flux coating prevented the formation of the metallic bond between copper and aluminum. Instead, high concentrations of potassium, magnesium and fluoride, coinciding with formation of KMgF3 and MgF2, were detected in the interface. In the castings without surface treatment, a continuous metallurgical bond was achieved. In the bond layer, various Al-Cu intermetallic phases have been detected. In addition, formation of primary silicon particles in the reaction layer was observed in all castings. The mechanism for the formation of the intermetallic phases and the strength of the interface layer have been discussed.INTRODUCTION Recent development in the automotive industry has focused on producing lightweight components, which can reduce CO2 emission and increase the efficiency. Often, one material alone is not able to meet the requirements for a specific use. The need for lightweight bimetallic components has therefore increased. Aluminum-copper bimetallic components can be used in wires and bus bars where conductivity is an important factor (Lee, Bang, & Jung, 2005). Compared to Al-Cu alloys, Al-Cu bimetallic components can reduce both weight and cost without reducing electrical and thermal conductivity (Sheng, Yang, Xi, Lai, & Ye, 2011). A challenge is, however, that aluminum and copper have high affinity to each other, especially at elevated temperatures. This causes formation of brittle intermetallic phases with high electric resistance (Liu, Wang, Sui, Wang, & Wenjiang, 2016). In addition, both metals are subjected to oxide formation on the surface. Copper is especially exposed to oxidation at elevated temperatures (Pinnel, Tompkins, & Heath, 1979), while a thermodynamically stable oxide layer will spontaneously form on the aluminum surface (Papis, Loeffler, & Uggowitzer, 2009). Oxides are known to be passive substrates, which will reduce wettability and will thus prevent the formation of metallic bonding between aluminum and copper (Papis, Hallstedt, Löffler, & Uggowitzer, 2008)."

Jan 1, 2018

By R. G. Gillies, C. A. Shook, W. H. W. Husband

"The current state of knowledge concerning pipeline transport of coal in water slurry form is summarized for the four categories: coal-water fuels, conventional fine coal slurries, coarse coals and stabilized mixtures of coarse and fine particles. Surface chemistry is of dominant importance for coal-water fuels and considerable progress in understanding the role of surfactants has been achieved in recent years. Little generalized research on the flow of conventional fine coal slurries has been done in the past 17years, although innumerable conceptual designs and feasibility studies have been undertaken. Coarse coal slurries are fairly well understood but the model which explains their flow requires more data to be established fully. Stabilized flow mixtures should probably obey the same model as coarse coal slurries but experimental results for stabilized mixtures have not yet been incorporated in a comprehensive theory.IntroductionPipeline transportation of coal in a water vehicle has been employed for many years in coal washeries. It has been used less frequently in hydraulic mining and thermal power station fuel supply systems. The suitability of coal for pipeline transport arises from its moderate specific gravity relative to the carrier fluid and the fact that throughputs are often large and steady over long periods of time."

Jan 1, 1990

By G. Shore

Radiation grafted structures my be fabricated to contain ion exchange groups selective to an ion complex. Proper choice of substrate and monomer will provide selective ion exchange with differing physico and chemical properties. Grafting a selected monomer to the proper polymer will provide selective ion exchange with assured chemical protection of the substrate. Ion exchange systems utilizing radiation grafted structures have been fabricated to ''capture'' gold, silver and palladium from dilute solutions. Other ion exchange systems can feasibly be produced to remove other precious metals. Rotating Cathode Technology is used to recover the metals from their regenerating solutions are pure metal foil.

Jan 1, 1985

By M. R. Babcock

"The Rabbit Lake story began in the late sixties and will continue well into the twenty-first century. It is a story of success, of multiple ore body discoveries, of unique systems, and new methods made possible through innovative and state-of-the-art design. Two quite different geological systems host the five ore bodies mined, or slated to be mined. These two systems have yielded two distinct ore types, each with characteristic mineralogical properties and each requiring its own specific mill circuit.Emphasis on communications and our unique systems have led to a satisfactory and fulfilling work environment resulting in the historically low employee turnover which has contributed to the operation success.A comprehensive environmental study after twelve years of operation has given the Rabbit Lake Operation a completely clean bill of health. INTRODUCTIONRabbit Lake can be described as Saskatchewan's first highgrade uranium mining operation, which set the stage for the province's current role as the leader in uranium mining throughout the western world. The importance of the Rabbit Lake operations - past, present and future.LocationThe Rabbit Lake operation is located in northeastern Saskatchewan (Fig. 1)- 805 km north of Saskatoon, Saskatchewan, and 814 km northeast of Edmonton, Alberta. OwnershipGulf Minerals Canada Limited discovered the Rabbit Lake deposit in 1968. Mining operations began in 1975and were operated by Gulf until purchased by Eldorado Nuclear Limited in 1982. In 1988, Eldorado merged with Saskatchewan Mining Development Corporation (SMDC) to form Cameco-A Canadian Mining &. Energy Corporation. The new corporation is one of the world 's largest uranium companies.Cameco's $1.5 billion in assets include the Rabbit Lake uranium mine (Cameco 100010); the Key Lake uranium mine (Cameco 66.67%; Uranerz Exploration and Mining Limited 33.33%); the Cluff Lake uranium mine (Cameco 20%; Amok Ltd. 80%); the Fuel Services Division at Blind River and Port Hope, Ontario (Cameco 100%); and a 100%); and a 48.75% interest in the Cigar Lake uranium deposit which is now at the test mining stage (Cogema Canada Ltd . 32.625% ; Idemitsu Uranium Exploration Canada Limited 12.875%; Corono Grande 3.75%; Korea Electric Power Corporation 2%). In addition, Cameco is involved in a number of base and precious metal explor ation projects."

Jan 1, 1989

By B. W. Snyder

INTRODUCTORY THE earliest known case of transmission of natural gas by pipe lines was early in the Christian era when the Chinese used bamboo pipes to transport natural gas from surface seepages to heat brine for the recovery of salt. Since that time many materials have been used as conduits-hollow wooden legs, wood stave pipe, day tile, cast iron, and, finally -since about 130 years ago - steel pipe. Even then, this new material came into use rather . slowly for, as recently as 80 years ago, wood pipe was still being used. However, as techniques were developed to take advantage of the properties of steel, this material gradually replaced all ethers for the transportation of gas for longer and longer distances at ever increasing pressures. In 1912, one of the longest pipe lines of its size at that time was built-this was a 16-inch line bringing gas from Bow Island to Calgary, a distance of 170 miles. We have been able to find records of only two ether such lines at that time-one a 185-mile 16-inch line from Vivian, Louisiana, to Little Rock, Arkansas, completed in the summer of 1911, the ether a 280-mile line from West Virginia to Toledo, Ohio. This last ? mentioned line was reported in a magazine article of September, 1912, but no indication was given of its size on completion date. It is apparent, therefore, that modern high pressure transmission of natural gas is a technique less than forty years old.

Jan 1, 1951

By A. A. de Gast, R. B. James

"The metal content of ore blocks can be calculated by the use of many different methods. These methods range in sophistication from manual calculation to computer. oriented techniques. In this case a cubic polynomial regression model is developed to depict the grade distribution of an orebody. Mine production, in stope dimensions, is then simulated on a computer to predict the output of metal content. The volume, grade and variance of the grade are estimated by triple integration and matrix algebra. A case study shows reasonable agreement between the results from the mathematical model and the mine geologists' estimate of production and ore reserve grade and tonnage."

Jan 1, 1972

By D. M. Ward, J. H. Ahrens

"The Fond-du-Lac uranium deposit was delineated primarily by percussion drilling and a small program of diamond drilling. Drillcore samples from three diamond drill holes as well as digitized gamma logs from percussion and diamond drill holes were utilized to define and implement an algorithm for the conversion of gamma-log data to equivalent-grade data. The procedures and detailed analysis for the provision of assay data for uranium reserve estimation are documented.IntroductionThe Fond-du-Lac uranium deposit is on the south shore of Lake Athabasca, approximately 2 km southeast o f Fond-du-Lac , northern Saskatchewan. It is on the northern rim o f the Athabasca sandstone basin.A train of mineralized glacial erratics was discovered in 1967 by Farnok, Limited by means of a helicopter-borne radiometric survey. In 1969, a program of diamond drilling by Famok was successful in locating in-situ mineralization in the Athabasca sandstone at the apex of the mineralized boulder train. Since 1974, exploration and development work have been performed under a joint-venture agreement between Eldorado Nuclear Limited and Famok Limited, with Eldorado acting as operator.From the discovery drill hole to the development of the gamma-log to equivalent-grade con version algorithm, the deposit had been tested by a total of 222 drill holes, 210 of which were percussion holes and 12 of which were diamond drill holes. The holes are generally vertical and collared at 10-metre centres on fences spaced 20 metres apart. The deposit is approximately 390 metres long, 10 to 40 metres wide and up to 45 metres deep, and is generally confined to the Athabasca sandstone. Uranium occurs as pitchblende, coffinite and uraniferou s goethite."

Jan 1, 1983

By A. Miura, G. Granata, C. Tokoro, A. Fuwa

"The high copper demand as well as the lack of new high-grade deposits, are pushing the copper industry to process low-grade and refractory ores containing chalcopyrite. However, for a quantitative dissolution of copper from the chalcopyrite, the leaching performances still need to be improved. In the present research, we studied and optimized the iodide-assisted leaching of chalcopyrite in H2SO4-Fe2(SO4)3 media. The evolution of surface species during leaching was determined by x-ray photoelectron spectroscopy (XPS) and mineral liberation analysis (MLA). Inductively-coupled plasma spectrometry (ICP-MS) was used to determine the dissolved copper. Significance of experimental results was assessed by statistical analysis while a kinetic analysis of the leaching process was performed by fitting the experimental data with the Shrinking-core model. Results showed the significant positive effect of iodide on copper extraction rate. In the presence of KI, the dissolution rate of copper was almost double than in the parallel experiments without KI. Whether using KI or not, elemental sulfur was generated on the surface of the leached chalcopyrite. Nevertheless, in the presence of KI, the passivation layer did not arrest the leaching. Analysis revealed that the leaching rate was limited by the chemical reaction control step.INTRODUCTION Due to the large demand of copper, processing low-grade ores containing copper sulfides such as chalcopyrite (CuFeS2) has become unavoidable (Watling, 2013). Since ores with CuFeS2 may also contain appreciable amounts of arsenic that cannot be smelted, and because low-grade ores are uneconomic to smelt, the hydrometallurgical technologies are crucial for recovering the copper (Dutrizac, 1978). Sulfate-based processes are attractive because of the lower operating costs and because the sulfate ion is more suitable in case copper would be recovered via electrowinning. In ferric sulfate solution, chalcopyrite undergoes oxidation due to the large amount of Fe(III) and dissolution due to the presence of the sulfate ion (Majima, et al., 1985). The leaching reaction in ferric sulfate medium can be represented as in (1):"

Jan 1, 2017

By Jason Mewis

Jason Mewis is the founder and president of ENGCOMP, a consulting engineering firm in Saskatoon Saskatchewan focusing on the mining sector. He has over 17 years of experience working on projects for the heavy industrial market in Saskatchewan, as both a Senior Structural Engineer and Project Manager. Jason is an entrepreneur with experience in many areas including estimating, planning, facilitation, and Risk Analysis. He has presented at many seminars and conferences across North America on the subject of Project Risk and and has become recognized for his expertise in this area of project management.

May 1, 2013

By E. G. Gaylord

THE material improvements which have been made in the practice of exploiting oil and gas reservoirs in the United States during recent years may be attributed largely to: (1) The necessity for drilling deeper wells at costs not much greater than was formerly expended on shallower wells. (2) The necessity for producing oil at a lower cost per barrel. (3) A growing recognition of the importance of the nature of production practice upon ultimate yield of oil and gas. The first two of these factors result, to a large extent, from the fact that a greater proportion of new development has been deeper development, and these wells have been drilled in the face of progressively lower per well allowables. In California, for instance, maximum allowables have declined from 400 barrels per day in March, 1938, to 156 barrels per day in September, 1940, and during this same period some 125 wells were drilled to the deeper 10,000-foot producing horizons discovered during this time. The third item listed above results from our increasing knowledge of the basic factors which influence the amount of recovery we may expect from reservoirs. In addition to the longer-range planning now being undertaken by the more prudent operators, State proration and conservation laws have focused attention upon the importance of methods conducive to obtaining progressively greater quantities of the hydrocarbons in place. In a paper of this length it will be possible to discuss only a few of the recent advances. An effort has been made to select the more important of these and to indicate, where possible, the factors which have made these advances possible.

Jan 1, 1941

By S. Steinlechner, S. Wegscheider

"In the past, the metallurgical industry was most of the time dedicated on their main commodity, recovering base metals like zinc, copper or lead but leaving other valuable side elements in the generated residues. As a result, these accompanying minor elements, like gold, silver, indium or also PGMs can be found in the dumps of the corresponding industry. Because of political unrest, strikes, economic reasons or decreasing primary resources leading to a high supply risk, also those mentioned minor elements moved into the focus of the recycling industry. Therefore, beside the base metals, first of all the recovery of those minor metals would be of high interest contributing to the economic viability of recycling processes, although they occur in much smaller quantities in materials. In this context, residues from zinc industry, like leaching residues or precipitation residues show high potential to carry silver as well as indium next to lead and zinc. Therefore, the paper summarizes carried out thermochemical calculations investigating a possible recovery of silver as well as indium by volatilization and the influence of zinc and lead on this process. Based on these theoretical investigations with HSC, trials in lab scale were done verifying the obtained results.INTRODUCTIONHuge amounts of iron precipitate, mainly jarosite get landfilled every year although there is a high content of valuable metals in this residue beside iron. Nevertheless, jarosite has to be dumped due to the presence of contaminating heavy metals. The accumulation of these residues takes up massive land on the one hand but also causes a series of environmental problems in ecosystems on the other. Moreover, some toxic ingredients such as arsenic and cadmium can be dissolved in rain water and are therefore harmful to the health of the aquatic systems. (Erdem & Özverdi, 2011; ÖzverdI & Erdem, 2010) Approximately 0.5 t of dry jarosite accumulate in the production of 1 t of zinc by the hydrometallurgical zinc-winning route (Svens, 2010). Jarosite is a precipitation residue formed during the iron removal. In general, the iron already exists in the zinc ore which is why zinc ferrite builds up during the roasting step of the zinc ore. Zinc ferrite is only soluble in strongly acidic solutions and during the hot acid leaching step it gets dissolved while zinc and iron enter the solution. It is necessary to get rid of the iron because otherwise it would deposit on the cathode first due to its precious character which would be harmful in the zinc-winning electrolysis. Nevertheless successful investigations were done by adding chlorine to the jarosite to recover silver. These findings leads to another residue which occurs in huge amounts – electric arc furnace dust (abbreviated with EAFD) from the iron and steel industry. In 2013 the annual electric steel production reached about 451 million tons. Around 15-20 kg of EAFD is produced per ton of steel in an electric arc furnace (EAF), creating approximately up to 9 million tons of dust per year. (Grabda, Oleszek, Shibata, & Nakamura, 2014; World Steel Association) Next to elements like zinc, lead and iron, chlorine and fluorine are present in this dust. While galvanized steel plates in the scrap act as a source for zinc, casting powders, flame retardants and synthetic coatings are responsible for the chlorine and fluorine contents in the dust."

Jan 1, 2016

By H. J. Meyer

"A hydrostatic elevation difference meter has been developed for use in measuring elevations along gravity traverses. Elevations of stations 100 feet apart can be obtained at a rate of 1/2 mile per hour and to an accuracy better than 1/3 foot. This can be done along traverses which have not been cut and chained. The instrument is durable, lightweight and constructed of materials which will withstand any temperature encountered in field work.It is believed that this device will more than double the rate at which gravity surveys over mining prospects can be carried out."

Jan 1, 1972

By M. Abzalov

"Control of analytical data quality is usually referred to in the mining industry as Quality Assurance and Quality Control (QAQC), and involves the monitoring of sample quality and quantification of analytical accuracy and precision. QAQC procedures normally involve using sample duplicates and specially prepared standards whose grade is known. Numerous case studies indicate that reliable control of sample precision is achieved by using approximately 5% to 10% of field duplicates and 3% to 5% of pulp duplicates. These duplicate samples should be prepared and analyzed in the primary laboratory.Bias in the analytical results can be identified by inclusion of 3% to 5% of the standard in each sample batch. Several different standards are used, with values spanning the practical range of grades in the actual samples. A blank (a sample in which the concentration of metal of interest is below detection limit) should also be included. Standard samples alone cannot identify biases introduced during sample preparation, and therefore approximately 5% of the duplicate samples (coarse rejects and pulp) should be processed and assayed at another, external, reputable laboratory.This paper discusses techniques used for estimation of errors in precision and accuracy, and overviews diagnostic tools. It is shown that one of the most commonly used methods, the Thompson-Howarth technique, produces consistently lower results than other methods. These results reflect the nature of this method, which relies on the assumption of a normally distributed error, and thus produces biased results when errors have a skewed distribution. This study concurs with the suggestion of Stanley and Lawie (2007: Exploration and Mining Geology, v. 16, p. 265-274) to use the average coefficient of variation (CVAVR(%)) as the universal measure of relative precision error in mine geology applications: Le contrôle de la qualité des données analytiques est habituellement désigné sous l’appellation d’Assurance et Contrôle de la Qualité (ACQ), elle implique le suivi de la qualité des échan¬tillons et la quantification de la reproductibilité et la précision analytiques. Les procédures des pro¬grammes d’ACQ impliquent habituellement l’usage de duplicata et de standards analytiques dont la teneur est connue. Plusieurs études de cas indiquent qu’une bonne fiabilité du contrôle de la précision des échantillons est atteinte par l’usage de 5% à 10% de doublons sur le terrain et de 3% à 5% de doublons de pulpe. Ces duplicata devraient être préparés et analysés au laboratoire principal.Un biais des résultats analytiques peut être identifié par l’inclusion de 3% à 5% d’échantillons standard dans chaque envoi d’échantillons. Plusieurs standards sont utilisés, avec des valeurs couvrant l’étendue des teneurs habituellement rencontrées dans des échantillons réels. Un blanc (un échantillon dans lequel la concentration d’un métal donné est sous la limite de détection) devrait aussi être inclus. L’emploi exclusif d’échantillons standards ne permet pas l’identification de biais résultant de la préparation des échantillons, de telle sorte qu’environ 5% des duplicata (rejets grossiers et pulpes) devrait être traités a un autre laboratoire indépendant et fiable.Cet article passe en revue les techniques utilisées pour évaluer l’erreur liée à la précision et a la reproductibilité, et effectue aussi un survol de divers outils diagnostiques. Il ressort de cet examen qu’une des techniques les plus fréquemment utilisées, la méthode Thompson-Howarth, fournit des estimés systémati¬quement inférieurs à ceux provenant des autres méthodes. Ces résultats sont un reflet de la nature de cette méthode, laquelle assume une distribution normale de l’erreur, biaisant ainsi les résultats lorsque l’erreur présente une distribution asymétrique. La présente étude recommande de privilégier l’usage du coefficient moyen de variation (CVAVR(%)) en tant que mesure universelle de la précision relative de l’erreu"

Jan 1, 2008

By C. Cornejo, C. Schuffeneger, J. Rosas

"At the end of 2010 the AMSA Esperanza Concentrator started commissioning. Located in the Atacama Desert this project is the first of several large size concentrators developed recently to operate in Northern Chile. In addition to the new operations to be implemented in the short term, many existing installations are planning expansions. The use of large size equipment is one of the common characteristics of the new concentrators, but also new technologies are being considered and innovation is present in most cases. Sea water or desalinated water will be required to process large tonnages of sulphide copper ores as well as gold bearing ores, since process water supply from the Andes will no longer be available. The high cost of sea water or desalinated water supply and the high cost of energy are not a limitation as the current metal market scenario allows obtaining an attractive NPV even from installations designed to process relatively low grade ores. A review of the current concentrators being developed in Chile is presented, including a description of the main design issues related to technology and innovation. An analysis of the Chilean mining industry is also presented, detailing mine and plant capacities as well as expected final products.INTRODUCTION The mining sector in Chile has become a reference when analysing the large concentrator plants projected or currently in operation all over the world. At present and as a consequence of the high price of metal commodities, most South American countries have an active mining sector. Chile is known as a major producer of metals. First records of copper production exported to Spain are dated to the early XVII century. Since then Chile has produced over 13% of the total copper ever produced in the world. After 1990 Chilean mining and the associated cluster of activities has substantially grown to levels never reached before, especially in the production of copper, gold and other non-metallic minerals. This dramatic increase is the result of an economic policy based on delivering comparative advantages and incentives for the admission of foreign capital to offset the weak domestic investment in previous decades. Massive mining of its huge mineral resources has allowed Chile to be a world leader in the production of copper and other base metals and mineral products."

Jan 1, 2012

By Melissa Whellams

?? What is a social risk assessment (SRA)? ?? Why do a SRA? ?? When do you do a SRA? ?? How do you do a SRA? What is a social risk assessment? ?? SIA vs. SRA ? SIAs determine how a company?s project will affect social/cultural conditions in a region ? SRAs determine how social/cultural conditions will affect the risk profile of a company?s project Social risk context includes: ? review of human rights record ? analysis of conflict situation ? analysis of political climate ? stakeholder identification ? stakeholder concern/interest identification ? And so on?

May 1, 2008

By J. A. Brothers, M. R. Foran

"AbstractThis paper reviews the progress made in the manufacture of hydraulic cement from iron blast-furnace slag by simply grinding the granulated material with other constituents. The influence of the chemical and mineralogical composition of the slag, the conditions of granulation, the manner of drying, and the fineness of grinding, on the hydraulic properties of the cement, is discussed. The effect of additions of lime, portland cement, and anhydrite, alone and in combination, on the physical and cementing qualities of the mortar and concrete made from Sydney blast furnace slag, is shown in tables of data and is reviewed in some de- tail. The work at the Nova Scotia Technical College has shown that a cement equivalent in every respect to portland cement can be made from basic blast furnace slag- by the us2 of certain quantities of portland cement as an activator.IntroductionBlast furnace slag is a potentially valuable material for the manufacture of hydraulic cement. It is a by-product of the manufacture of iron in the blast furnace, and is formed by the combination of the silica and alumina .of the iron ore with the limestone flux. The metallurgist terms a slag .acid or •basic according as the percentage of lime is less or greater than the percentage of silica plus alumina. The basic slags have the •more pronounced hydraulic properties."

Jan 1, 1950

By E. J. Fuller, J. C. Monette

"Gold and silver cyanide complexes are presently desorbed from activated carbon by means of hot caustic elutions. These solutions may or may not contain additional sodium cyanide. There are several parameters which affect the rate of stripping. Some of these include pH, ionic strength, and temperature. (1) Stripping is conducted in recirculating (ZADRA) or once through (AARL) circuits.This paper describes the development of a new chemical eluant which significantly increases the rate of stripping of both gold and silver cyanide complexes from activated carbon. Two case history applications are also described.INTRODUCTIONAdditional cyanide is used in strip circuits in order to prevent its depletion which could lead to precipitation of base metals or lead to a change in the nature of the gold cyanide complex to one which does not strip as easily. (2)The strip circuits that are able to function efficiently without the use of cyanide are mostly those where the carbon is acid-cleaned after stripping.Once the minimum cyanide requirement to maintain the complexes in their proper state are fullfilled, any futher incremental increase in the level of cyanide will have no bearing on the rate of stripping. (3)DEVELOPMENT OF THE NEW ELUANTGeneral DiscussionVarious carboxylated materials were investigated including octanoic acid, polycarboxylic acid (various molecular weights), salicylic acid, polymaleic acid, acetic acid. benzoic acid, terephthalic acid, 4, bi-phenyl carboxylic acid, phosphoric acid and stearic acid.The initial work was done on medium activiiy, non acid-cleaned carbon. The silver to gold ratio on the carbon varied greatly.Two different blanks were used. The first was an elution using a 2% caustic and 0.4% cyanide solution while the second was a 2% caustic elution."

Jan 1, 1992

By Garry Johansen, Andrew McCallum, Sandy Gray, Gary Patrick, Jennifer Abols

"The authors challenge the traditional thinking that whole ore cyanidation followed by Carbon in Pulp (CIP) or Carbon in Leach (CIL) should be applied as a standard process in the majority of gold processing flowsheets. The concept of whole ore leaching by using cyanide can result in unnecessary environmental and capital risk. Alternative, currently available technologies can be used to provide the desired level of gold recovery at a much lower installed cost and less impact on the environment. Gravity concentration, alone or in conjunction with flotation, can produce a gold bearing concentrate that can then be fed directly to a batch or continuous intensive cyanidation unit.The InLine Leach Reactor (ILR) is an intensive cyanidation unit developed by Gekko Systems of Australia. Advantages of this technology include significantly reduced capital outlays for greenfield plants or plant upgrades and increased investor returns. Reduction of onsite cyanide and carbon inventories improves plant safety, materials handling and site security. By using direct electrowinning to treat the gold bearing solutions produced by the ILR, the need for a conventional carbon stripping circuit is removed. Potential also exists to increase grind size – saving energy, further reducing capital and operating costs and decreasing the environmental impact of a mill. Detoxification of cyanide before the release of solution to the tailings dam can minimise tailings disposal and containment requirements.When used in the right application the proposed process will have little or no impact on gold recovery and may actually increase recovery for complex ores. Areas applicable to this type of treatment include: plants in environmentally sensitive regions, lower tonnage higher grade deposits, coarse gold deposits, and preg robbing ores - some of which may not currently be economically feasible using standard processes and flowsheets. We have provided three examples of such projects, where an alternative to whole ore leach and CIP or CIL has delivered these benefits."

Jan 1, 2003