Search Documents

By P. G. Semple

"In January 1985, Equity Silver Mines Limited began operation of a cyanidation circuit to scavenge precious metals from the flotation tailings. At present, this process is treating 270,000 tonnes of tailings per month and is recovering in excess of 0.20 grams of gold per tonne. To obtain these results Equity is operating a carbon-in-leach circuit that utilizes pressure stripping, zinc precipitation acid washing and thermal reactivation. A cyanide destruction circuit is also required to minimize the deleterious effects on reclaim water in the flotation stage. This paper describes the existing scavenger plant, and details the start-up problems encountered and the modifications made to correct these problems.INTRODUCTIONEquity Silver Mines Limited , a 68% owned subsidiary of Placer Development Limited , is located 38 km southeast of Houston in north central British Columbia. The geographic location of Equity Silver Mines is shown in figure #1. In September 1980, production first began with the ore being supplied from the Southern Tail open pit. In March 1984, the Southern Tail deposit had reached its economic pit depth, and since then ore has been supplied by the Main Zone pit the gold mineralization in the Main Zone is less refractory than the Southern Tail and cyanidation of the flotation tailing appeared to be a viable alternative.An extensive test program was undertaken and the results confirmed that considerable gold and silver values were amenable to cyanide leaching. A feasibility study showed that these values could be economically recovered and the detailed engineering work began."

Jan 1, 1987

By S. Pinard, A. Desbiens, R. del Villar, D. Jakelski

"During the fall of 1993, a new Pill-based control strategy was installed in the B grinding circuit at the Kidd Creek Division of Falconbridge Ltd. The control strategy was first evaluated on a grinding circuit dynamic simulator (DYNAFRAG), which permitted the discrimination between more than a dozen possible control alternatives. Once the final choice was made the necessary instruments were purchased and installed. The control strategy was configured on the plant computer and is planned to be commissioned shortly.This paper summarizes the control strategy, the design procedure, the installation and the controller tuning. Some preliminary problems posed by the process prior to implementation are also presented.IntroductionIn 1990 the GRAIIM (french acronym for Research Group on Computer Applications to the Mineral Industry) of Laval University started a research project on Knowledge Based Automatic Control (KBAC). This project is sponsored by a consortium of eight mining companies under the umbrella ofMI1EC (Mining Technology Council of Canada), the Quebec Mining Association (AMQ), CANMET and the Centre de Recherches minerales (CRM). The project also benefits from important grants from the Ministere de l'Education Superieure et de la Science and the NSREC-CRD program.The main objective of this project is the screening of advanced (knowledge-based) methods for data processing (filtering, mass balancing, etc.) and automatic control (model-based control) for their use in the mineral processing operations. The project also aims at transferring these tools to the industrial partners through annual workshops for plant engineers, annual symposia, and through specific in-plant projects where the participation of plant engineers is strongly encouraged.The main objective of this project is the screening of advanced (knowledge-based) methods for data processing (filtering, mass balancing, etc.) and automatic control (model-based control) for their use in the mineral processing operations. The project also aims at transferring these tools to the industrial partners through annual workshops for plant engineers, annual symposia, and through specific in-plant projects where the participation of plant engineers is strongly encouraged."

Jan 1, 1994

By A. Sadough vanini A. Kami

In this paper, effects of different ageing treatments on the mechanical properties, microstructure and formability of 7075 aluminum alloy have been studied. Forming limit diagrams of the alloy have been obtained for four ageing conditions including T6, OA1, OA2 and O. For this purpose, combination of uniaxial tensile tests and the Erichsen cupping tests with different sizes and shapes of sheet specimens have been performed after each ageing treatment. The highest formability and the lowest formability have been observed at samples with O and T6 ageing treatments, respectively. Also, investigation of precipitated microstructures showed that the size of precipitation particles has a significant effect on the formability of the alloy. Formability improves with coarsening of precipitation particles.

Oct 1, 2011

By A. Brown

THIS P APER has been pre-pared as a progress report on Mines Branch investigations into problems of ground stress in certain co al mines of Western Canada. As such, it should be considered as a companion report to the one ( 1) presented to the Mining Society of Nova Scotia in 1956 and which dealt with similar investigations in the coal mines of Eastern Canada. For the past 50 years, dynamic incidents in the form of 'bumps' and 'outbursts' have been occurring in the coal mines of the Inner Foot-hills belt of tl1e Canadian Cordillera. As these phenomena generally become more frequent with in-creased thickness of overburden, a limiting depth of mining of 2,500 feet has been set (2) for estimating recoverable reserves of coal. If such a view were accepted, from a long-term viewpoint very large resources of coking-grade ?coal -in a part of the continent deficient in such coals -would not be available to the nation. The terrain in which these in-6dents take place may be described in geological terms as being dominated by pronounced structure in strata ?consisting of a large proportion of highly indurated rocks. The Geological Survey of Canada has co-operated by carrying out structural studies (3) at the mines, supplemented lithological by stratigraphic observations.

Jan 1, 1958

By Fathi Habashi, Michel Pagé, Farouk T. Awadalla

"Chrysotile asbestos can be dyed with certain dyestuffs to form stable coloured products whose hemolytic and cytotoxicity are greatly reduced. Examples of these dyes are Thiazol Yellow G (a monazo dye) and Trypan Blue (a diazo dye). Other dye stuffs, for example, basic dyes with triphenyl methane structure, Brilliant Yellow (a diazo dye), and Methylene Blue (a thiazine dye) colour asbestos but do not reduce its toxicity. Similarly alizarin, 8-hydroxyquinoline, and representative members of the phthalein group Bromocresol Purple and Phenolphthalein.IntroductionThere is, at present, a controversy regarding the dangers of asbestos fibres, and attempts are being made to render it less toxic. One of these attempts consisted of treating chrysotile asbestos with gaseous phosphorus oxychloride, POCI], at ambient temperature and in absence of moisture. The product had to be heated at 300°C to 500°C to expel exess entrained reagent to get a material containing 0.5070 to 5% phosphate groups and known as Chrysophosphate (Lalancette and Dunnigan, 1982). This product showed decreased toxicity as measured by its hemolytic effect on red blood cells (fable 1). In another approach, Flowers (1983) showed that when chrysotile asbestos was thoroughly mixed with a solution of ferric ammonium sulphate and the slurry was then filtered and dried, the product showed a marked decrease in cytotoxicity.In the present investigation the problem of toxicity was considered from a different point-of-view. Chrysotile asbestos is a hydrated magnesium silicate that can be represented by the structural model shown in Figure 1 from which it can be seen that magnesium hydroxide groups, Mg(OH)2, form a part of the silicate structure. Certain organic reagents that are known to react with magnesium ion in solution to form chelates were reacted with asbestos to find out whether a chelate was also formed on the fibres, and if so , what will be the hemolytic action and cytotoxicity of the product."

Jan 1, 1991

By K. Halada

Current trend of the global flow of strategic metals are analyzed to discuss the strategy of the development of recycling technology and alternative technology. In many cases, each global flow of metal is changing from the trilateral structure of U.S., EU and Japan in the later 20th century into the convergence to China as the factory of the world. Scrap flows are also changing dynamically. A long term change of prices of metal has gotten changed since the entrance of this century. The estimation of metal consumption up to 2050, in which the author estimated that many kinds of metal will overshoot the reserve base line, is revised considering these change of current trends.

Jan 1, 2014

By J. E. Danoczi

Shore Gold Inc. (Shore) is presently designing a diamond processing plant for the Star and the Orion South kimberlite deposits in the Fort à la Corne (FalC) area in central Saskatchewan. The first step in the plant is diamond liberation and occurs in the comminution section. Diamond liberation is the process of breaking up the kimberlite rock, as gently as possible so as not to damage the diamonds. Autogenous grinding mills (AG mills) use a combination of impact crushing, abrasion and attrition to break up the kimberlite. The forces that occur during the actions of abrasion and attrition cause the kimberlites to break up preferentially along lines of weaknesses which offers a ?diamond friendly? method of comminution. Hard competent kimberlite is commonly found in the diatreme zone as well as the root zone of the volcanic pipe and is the source of kimberlite for most of the Southern African diamond mines. Softer kimberlite is typically found in and around the crater area of a volcanic pipe and it is this kimberlite that makes up the majority of kimberlite for both the Star and Orion South deposits. These softer kimberlites can be readily broken up using abrasion and attrition imparted by AG mills. In order for Shore to benefit from the softer kimberlite found in the Star - Orion South diamond project, two large (10.97 m diameter x 7.10 m long) AG mills were designed for the comminution section based on extensive test work and simulations by Metso Minerals (Metso).

Jan 1, 2012

By Arthur Barnes, Mika Muinonen, M. J. Lavigne

"The carbothermic reduction of chromite ore to produce high carbon ferrochromium is among the most energy intensive metal extraction processes performed, due not only to the highly endothermic nature of the reduction reactions but also the very high operating temperatures required for the smelting operation to separate the chrome-containing alloy from the discard slag.KWG Resources and XPS have collaborated over the last 3 years in developing a patented (Winter) processing alternative to the traditional smelting operation in which all processing takes place in the solid state at temperatures many hundreds of degrees lower than those required for liquid processing. Amongst the attractions of the process are much lower capital costs, as well as reduced operating costs, particularly of energy.A techno-economic study on the new process identifies a reduction in overall energy consumption of 70% against conventional processing and approximately 40% lower than the current best practice. By utilising more natural gas than coal based energy sources, the KWG process is able to show an overall 50% reduction in greenhouse gas emissions compared with the most energy efficient current practice. The impact of the new process on future processing is therefore regarded as highly significant, with global energy reductions equivalent to the effect of completely eliminating energy demand from a country the size of Italy.The study concluded that the potential for this process to completely revolutionise the global ferrochrome industry should not be underestimated. Its impact reaches far beyond exploitation of a regional natural resource."

Jan 1, 2015

By B. A. Watters, G. A. Parslow, F. H. Mcdougall

Carbonate-rich rocks occur at several localities within the Flin Flon volcanic sequence of the eastern Amisk Lake area. The rocks occur in two areas: as a group of small occurrences on islands within Amisk Lake and as two much larger linear belts running parallel to the regional structure east of Amisk Lake. Mineralogically, the rocks consist of talc and Ca-poor ankerite with occasional graphite. Segregation of these minerals and colour variation impart a well-defined planar fabric to the rocks and where the units are fairly continuous (e.g. Mosher Lake), their trend and attitude suggests a concordant relationship to the volcanics. Major and trace analysis of22 samples confirms the presence of two types, with one type being represented in each of the two areas. Most of the elements studied can be used to characterize the two groups, but three elements in particular give a clear separation: Mg, AI and Ni. Recalculation of the major element analyses, on a water and carbonate-f ree basis, indicates that one group (large concordant bodies with high MgO, high Ni and low AI20.J is altered ultrabasic material of peridotitic or dunitic composition. Because no relict igneous material is observed, and the contacts are apparently very sharp, it is possible that the hydration-carbonization process occurred simultaneously with intrusion, .in a closed system. The other group (small occurrences with relatively low MgO, low Ni and high AI203J represents alteration of basaltic rocks. AIthough some analyses suggest the introduction of calcium, as carbonate, along with the volatiles, the major oxides have remained remarkably stable during the alteration process(es).

Jan 1, 1981

By T. Negeri, M. Boisclair

"A hybrid process consisting of flotation and magnetic separation has been developed to concentrate multi-phase rare earth minerals associated with a carbonatite ore that contains a significant amount of niobium. Fine grinding to a d80 of <65 microns was required to obtain acceptable separation of 92% of the contained total rare earth oxide (TREO) and niobium in half the feed mass. Whereas it was possible to obtain 85% of TREO in 28% of the feed mass through staged cleaning, it was demonstrated that at least 87% and 85% recoveries of TREO and Nb respectively could be achieved in 16% of the feed if the rougher-scavenger concentrates were calcined, quenched, reground to <25 µm and then magnetically upgraded. The paper discusses the overall concept of the flowsheet and the experimental strategies that led to this progress. INTRODUCTIONOut of the approximately 250 minerals known to contain rare earth elements (REEs), only about 60 of them contain REEs in significant amounts. Over 95% of the world’s rare earth oxides (REOs) are believed to occur in the form of three minerals (Pradip & Fuerstenau, 1991) namely bastnaesite (Ce,La,Y)CO3F, monazite (Ce,La,Nd,Th)PO4 and xenotime Y(PO)4. An estimated 51.4% of global REO resources are hosted by carbonatite deposits with the same three minerals as major constituents (Weng et. al., 2015). Any one of the REEs or commonly all of them can be found in these minerals (Ravnaas, 2010). As the demand for critical REEs increases due to the ever increasing applications in advanced technologies, many deposits containing other forms of REE minerals will have to be developed. REE minerals are extensively dispersed and intergrown with several oxides, silicates, carbonates, and phosphate minerals. Consequently it is possible to liberate them only at fine grinding and is thus difficult to separate and produce high grade rare earth mineral concentrates. Most of these minerals contain other important elements such as tantalum (Ta), niobium (Nb), uranium (U), and thorium (Th) in varied quantities. REE minerals in the same ore may exist as carbonates, fluorocarbonates, niobates, silicates, phosphates etc. in association with gangue minerals belonging to different mineralogical groups."

Jan 1, 2016

By Robert F. Shurtz

This paper discusses and compares methods of statistical analysis of the information relating to the evaluation of an asbestos deposit. From a study of 10-ft. lengths of drill core, the separate effects of visual evaluation errors were determined, as well as the deviations between evaluators and the deviations produced by a slight displacement in the center lines of the check drill holes. The importance of careful statistical analysis of such information is stressed.

Jan 1, 1966

By J. C. Glandus, N. Tessier-Doyen, M. Huger

The Young&apos;s modulus of bi-phased model materials (vitreous matrix containing spherical alumina inclusions) have been determined by two complementary approaches: experimental and analytical. If the matrix and inclusions exhibit close coefficients of thermal expansion, the experimental results lie in the vicinity of the lower bound of the Hashin & Shtrikman&apos;s model. If there is a dilatometric disagreement between the components, untypical behaviors, similar to those obtained for a family of industrial refractory materials, were observed when the temperature varies.

Jan 1, 2004

By I. Govender

Positron-Emission-Particle-Tracking (PEPT) has enabled the non-invasive observation of charge and slurry transport in model mills under operational conditions. We use high quality PEPT data to infer that the charge motion can be effectively described by a non-Newtonian granular fluid. An improved theory for slurry transport, including inertial effects, is presented.

Jan 1, 2012

By D. A. Barr

High-grade gold-silver mineralization associated with electrum and argentite was discovered in a quartz vein at the Chappelle property, 273 km north of Smithers, B.C., in 1969 following a regional geochemical reconnaissance program in the Cassiar-Omineca Mountains. Subsequent exploration resulted in the discovery of numerous quartz veins with associated precious-metal values in a belt 17 by 3 km in area centrally located within Toodoggone Group volcanic and sedimentary rocks of Lower to Middle Jurassic age and a window of Takla Group volcanic rocks of Upper Triassic age. More detailed investigations, consisting principally of 5677 m of surface drilling in 57 holes and crosscutting, drifting and raising on Chapelle Vein A, has outlined a high-grade gold-silver-bearing shoot with a strike length of 200 m, an average width of about 3 m and extending to an average depth of about 40 m below surface.

Jan 1, 1978

By E. R. Olson

The introduction gives not only a historical background but also touches on shaft sinking and surface construction and gives some general information on the Potash Conservation Regulations which the Saskatchewan government introduced in 1969. It also gives information on the corporate and local organization of Alwinsal Potash.

Jan 1, 1972

By A. J. Sinclair

"Abstract-Geology contributes essential information toward obtaining high-quality resource/reserve estimates. In this context, geology can be considered under the following overlapping topics: regional geology, detailed (deposit) geology, mineralogy, ore deposit models and continuity, with geological mapping being fundamental to all. Each of these topics is considered here in terms of potential contributions to "improved" mineral inventory estimation. Some of the principal conclusions are:1. Regional geological relations must be consistent with deposit geology. It is common that important geological relations are more clearly evident in various regional locales than in highly altered and/or highly deformed mineralized areas containing mineral deposit.2. Detailed geology provides information for a geometric model of a deposit, a model that serves as a basis for mine planning. It is important to distinguish fact from interpretation in such models. Substantial effort is required to characterize the geometric margins of a deposit and the relation of these margins to the simplistic geometric form that normally emerges as an interpretation.3. Mineralogical studies relate to many aspects of deposit evaluation including abundance of ore and deleterious minerals, spatial distribution of ore and deleterious minerals, grain size characteristics of important minerals, mill design, etc.4. Ore deposit models contribute substantially to confidence in developing a three-dimensional geometric model of a deposit for mine planning. Specifically, they are a basis on which to develop rules for interpolation and extrapolation of ore, and they contribute to recognition of domains, each with its own characteristic continuity and margin character.5. Continuity is dependent on mineralization style and may be controlled structurally and/or chemically. It is important to distinguish geological continuity and value continuity. A wide range of classical geological methods are useful in examining geological continuity; value continuity is best viewed as a statistical characteristic that is quantified by any of several measures of autocorrelation."

Jan 1, 1998

By D. J. MacDonald

UNDERGROUND development at the Lynn Lake property of Sherritt Gordon Mines, Limited, was begun in 1948 with the sinking of the A shaft in the area of the A orebody. By June, 1949, the shaft was completed to a depth of 1,024 feet. Twelve stations were cut, with the bottom level at 992 feet below the collar. Since completion of the shaft, lateral work has been carried out on the 12th level in order to expose the known orebodies and to provide openings from which deeper exploration could be conducted. Dur¬ing the change-over from sinking to lateral work, preliminary diamond drilling was done from the 12th level station to locate the A? ore-body. Later, drilling was carried out from the 5th and 9th level sta-tions, where, also, the outline of the A orebody was established. As the work progressed on the 12th level, and with the commence-ment of drilling below that level, the geological picture was found to be complicated by numerous faults. Instead of operating two drills it became necessary to use at least four. The original plans had provided air sufficient to drive two headings and to operate two diamond drills. The addition of two more air-driven drills resulted in a serious shortage of power.

Jan 1, 1951

By A. H. C. A. Zimmerman

WE have just heard what must be regarded as a thoughtful, constructive and somewhat painful analysis of the financial function of our industry. While thinking about this, it is interesting to reflect on the conditions which have stunted the growth of the financial side of our affairs. Mining must be regarded as a wealthy business. •while immeasurable grub takes and development budgets have been lost, there can be little argument that a productive ore-body nearly always produces the type of wealth that breeds some extravagance. I recognize that this statement can be attacked from many sides, but an historical comparison with a commercial enterprise involving similar investment will demonstrate what I mean. However, these old times are be-ginning to disappear for a variety of reasons. High amongst these are: ( l) Increased costs of exploration. (2) Remoteness of many new finds. (3) Fixed or declining metal prices (particularly when expressed in constant dollars). ( 4) Constant demands for higher wages.

Jan 1, 1962

By D. Brisebois, J. M. Fecteau, S. Poirier

"This paper focusses on new developments regarding thermal rock fragmentation applications. The technology consists of a strong burner powered by diesel fuel and air. The thermal reaction that is created allows for the enlargement of 125 mm to 450 mm holes by breaking the rock in a spalling effect. It has been used for over 30 years in Russian open pit mining. Following an agreement between Dynamitage T.C.G. Inc. and the owner of the technology, major improvements have been brought to this technology, allowing for the fabrication of a prototype suitable for the Canadian industry. In Russia and the Ukraine, thermal rock fragmentation is actually used to drill large diameter holes in surface mining. Upon having acquired a better knowledge of this technology, it seems that it presents a great potential for selective mining in narrow-vein operations, for either surface or underground mining.Rocmec International Inc., a subsidiary of Dynamitage T.C.G. Inc., and Natural Resources Canada are technical partners in the evaluation of the operational parameters and environmental aspects such as gas, heat, dust and fog emissions. Furthermore, Canada Economic Development is a financial partner in this project.This paper presents the technology and its history. It also reports on the changes brought to the equipment to adapt it to North American environments. A summary of the tests carried out since 1995 is provided, along with the main conclusions obtained. The anticipated applications for the use of this technology in both surface and underground environments are described such as open pit mining, bulk sampling and narrow-vein ore extraction. An estimate showing a comparison between the thermal fragmentation mining concept and the long-hole mining method is presented and, finally, the future developments planned are listed."

Jan 1, 2003

By S. Nikolic, G. M. Stieper, D. P. Mallah, B. J. Hogg, P. B. Voigt

Copper feed materials processing is becoming more challenging, due to an incremental increase in the mineralogical and compositional complexity of these feeds. These complex and polymetallic feeds are now becoming more common and many sites have been forced to re-evaluate their operating strategies to process these materials at cost competitive rates, whilst meeting ever more stringent environmental regulations. Most operations must first evaluate the merits of pyrometallurgical and hydrometallurgical treatment routes. Although there are multiple copper smelting technologies available, only top-submerged lance (TSL) technology, supplied by Glencore Technology as ISASMELT™, has been applied in the real world to consistently and successfully smelt complex materials in integrated metallurgical facilities such as Glencore’s Kazzinc Ltd. operation in Kazakhstan, Umicore Precious Metals Refining in Belgium and Aurubis AG in Germany. Glencore Technology also offers hydrometallurgical processing, through the Albion Process™ technology, opening up viable flowsheet options previously not possible for these complex feeds. This paper describes a number of real world process flowsheets at global operations and Glencore’s own operations at Mount Isa and Kazzinc Ltd., which process complex feeds. These flowsheets integrate the ISASMELT™, Albion Process™, ISACONVERT™, ISAKIDD™ Tank house, and bottom blown oxygen cupel (BBOC™) technologies to provide an effective process solution for the treatment of complex polymetallic feeds to produce metallic copper and associated by-products. INTRODUCTION Traditional smelters and those built in recent times within the bulk smelting hubs of the world have been designed to treat standard/clean concentrates. In recent years the processing of complex polymetallic sulfide concentrates and the recycling of secondary copper and derivatives of waste electrical and electronic equipment, such as e-scrap, have become a focus for numerous companies (Alvear & Nikolic, 2013). Processing of these complex feeds, characterized by relatively high levels of minor elements (over 5% of elements such as arsenic, antimony, bismuth, lead and zinc) is more challenging. Facilities not designed for these types of materials may require significant modifications or a change in smelting technology to treat them. Often operations find themselves re-evaluating the merits of pyrometallurgical and hydrometallurgical treatment routes for their sites through a number of factors:

Jan 1, 2019