Search Documents

By E. O. Lilge

THE USE of the Driessen cone as a heavy-media concentrator involves a mineral dressing process in which many variables inherent in the ore and in the process may have an effect on the efficiency of mineral separation and the operation of the cone. The magnitude of these effects and their possible interrelationships must be known before a full-scale plant can be designed and built. It appears that, among the most important variables, are the following: Ore Variables: The particle size of feed The difference in specific gravity between economic and non-economic minerals The intimacy of mineral association Cone Variables: Cone inlet area Ore to media ratio Cone ratio Size distribution in heavy media Specific gravity of media Viscosity of media Type of media

Jan 1, 1956

By J. R. Goode

"The Las Cristinas deposit in Venezuela contains reserves of 12.8 million ounces of gold at a grade of 1.20 g/t (Crystallex, 2004). The deposit comprises fully oxidized saprolite (SAPO) overlying a layer of sulphide-enriched saprolite (SAPS) which lies above carbonateleached bedrock (CLB) and carbonate stable or un-leached bedrock (CSB). Gold occurs at about the same concentration in all lithological groups. The bedrock units contain minor amounts of copper (about 0.1%) as chalcopyrite, while SAPO contains virtually no copper which has been leached and deposited in the SAPS zone.A previous owner began investigation of the Las Cristinas deposit in 1991. Over the next seven years, the company drilled 1,174 holes with a total length of 159 km, conducted extensive metallurgical testwork, including pilot plant operations, and completed feasibility studies. Construction was started in 1997 and again in 1999, however, on each occasion was suspended.Crystallex has been producing gold inVenezuela since the early 1990s. In 1997, Crystallex acquired Inversora Mael which had held two of the claims to the Las Cristinas concessions since 1986. In September 2002, Crystallex entered into a definitive agreement with the Corporación Venezolana de Guayana (CVG) to develop the Las Cristinas deposit.An extensive program of studies and testwork was started in late 2002 to determine an optimum development plan for Las Cristinas. Mine Development Associates, SNC–Lavalin Engineers and Constructors, SGS Lakefield Research Limited, J.R. Goode and Associates, and A. Laplante at McGill University acted as the main contractors.Because of the potential value of by-product copper, earlier flowsheets used carbon-inleach for SAPO, but processed all other ore types by flotation to produce a gold-copper concentrate with cyanide leaching of cleaner tailings to maximize gold recovery. Cyanide recovery was necessitated by the high copper content of the leach feed. Initial studies of available data by Crystallex revealed that direct leaching of all ore types would provide about 11% more gold recovery than the previously selected flotation route with reduced capital and operating costs.Bench and pilot-scale studies have confirmed that a SAG-ball mill-gravity-CIL route is very effective for all ore types and will give about 89% gold recovery. This paper describes the testwork conducted in 2003, discusses a 20,000 t/d plant design, and presents economic data."

Jan 1, 2005

By K. Yoo

Chalcopyrite is the most abundant copper sulfide mineral, which is normally processed using pyrometallurgical methods (i.e., smelting) to produce copper metal. Smelting has several major disadvantages, such as high gas-handling costs, high capital costs, saturation of sulfuric acid market, and inability to treat low-grade concentrates and to recover some by-products, such as zinc, nickel and cobalt. The development of hydrometallurgical processes for chalcopyrite is desirable to overcome the problems of smelting. Because chalcopyrite is refractory, the leaching rate for chalcopyrite is very low. Therefore, increasing the leaching rate has been extensively investigated, both in sulfate and chloride media, as well as in the presence of bacteria. Chloride leaching processes have shown relatively high leaching rates. The mechanism of the chloride leaching process has been investigated, but the behavior of chalcopyrite leaching in chloride solution is not clear. Therefore, the effect of the solution redox potential on the leaching rate of chalcopyrite in chloride solution was investigated. In the present study, leaching experiments were carried out using 0.1 M chloride solutions and the results indicate that high leaching rates of chalcopyrite can be achieved at relatively low solution redox potentials.

Jan 1, 2007

By R W. Drybrough

The program to increase production at Sherritt Gordon's Lynn Lake property, which began in 1956, included increasing the rope speed and the horsepower of the ore hoist at the "A" shaft. Because of the limited power sup-ply from the two 7,000-hp. hydroelectric plants, and the ? 3,600 hp. predicted for the combined hoisting requirements of the three production shafts, it was considered desirable to lessen the impact of this type of load on the relatively small power system by equipping all future hoisting arrangements with Ward Leonard direct-current drives. The manually operated 8-by 4-ft. hoist at the "A" shaft had a rope speed of 1000 f.p.m., and was driven by a 385-hp., 380-r.p.m. wound rotor motor with liquid rheostat control. This A.C. drive was replaced by a semi-automatic Ward Leonard direct-current drive with a 515-hp., 566-r.p.m., shunt wound motor, providing a rope speed of 1,500 f.p.m. During several months preceding the con-version, all possible preparations were carried out to keep the changeover period to a minimum, and this resulted in a total shutdown time of twelve days. The capability of the "A" Shaft hoist was increased from 109 tons per hour to 134 tons per hour, and both mechanical and electrical maintenance were reduced considerably. The total cost of the conversion amounted to $130,000. The hoistmen who had been required for the manual A.C. drive were transferred to the new Farley shaft, and the reduction in operating labour costs of the "A" Shaft hoist

Jan 1, 1965

By J. A. Orr

The details connected with the mining and subsequent handling of Creighton ore were fully covered in a paper presented to the Institute in 1920. The following brief notes describe certain phases of the present practice and show wherein it differs from the practice at that time. These may be summarized under the following headings. (a) Recovery of pillars. (b) Drawing the ore. (c) Change from sub-level tramming to branch-raise system. (d) Chute construction. The present stoping practice is the same as formerly, i.e., fiat-backed shrinkage stopes of 60-foot width, between rib pillars of 15-foot width, extending from the footwall to the hanging-wall. Formerly, when these stopes were completed to the stopes above, they were drawn empty of broken ore, and the 15-foot rib pillars were caved into the stopes and drawn off through the same chutes as were used to draw the ore from the stopes.

Jan 1, 1926

By Michel Aubertin

Using mine wastes as backfilling material for underground stopes has been a common practice for more than 60 years. Waste rock and tailings are used as filling materials because they are available at a reasonable cost to support the rock walls. Backfilling is also very advantageous because it reduces the amount of mine waste disposal on the surface. In underground mines, the backfill must first ensure stability of the opening, while increasing recovery of ore and minimising dilution. It is thus critical to accurately evaluate the pressures exerted on the walls and on the barricades placed near the base of the stope. In this presentation, existing solutions for evaluating the stresses on stope walls and barricades are briefly reviewed. The authors then present recently developed analytical solutions that take into account the stress transfer from the backfill to the walls in the stope and access drift. The stress state solution, which is based on arching theory, considers the influence of the stope geometry and barricade position within the drift. The method gives the pressure generated by partly or fully submerged backfill. The solutions apply shortly after backfill deposition, when the effect of pore water pressure cannot be neglected, and also for long term conditions under a fully drained state. Experimental testing and numerical modelling results are used to validate the proposed equations. Both numerical and analytical results show that the total pressure on barricades can be significantly increased by water pressure, while the effective stress is decreased (compared to dry or drained conditions). A discussion follows on the implications of the results for backfill applications.

Nov 1, 2008

By S. Esfahani, M. Barati, K. Danaei

"Substituting Portland cement with slag cement is one of the most economically attractive uses of slags. For this application, high cooling rates are required to form an amorphous structure. However, this is counteracted by the need to use small coolant flowrate to allow recovery of slag thermal energy as high quality heat to the coolant fluid. Therefore, a relationship between cooling rate of slag and its structure is essential to recover the heat effectively while making an amorphous slag.A modified Single Hot Thermocouple Technique (SHTT) was employed to investigate the crystallization behavior of slags by plotting their TTT (Time-Temperature, Transformation) diagrams. Seven different slag compositions containing CaO, SiO2, Al2O3, MgO were prepared at varying basicity (CaO/SiO2 =0.5-1.4).The results indicate that with increasing basicity, the TTT curves of glassy to crystalline transformation shift to the left which means higher crystallization tendency. This agrees with the fact that with the increase of basicity, the Si-O bonds are weakened, which in turn facilitates the re-ordering and crystallization of the silicate structure."

Jan 1, 2014

By K. Nagai

The Asian projects are now in their second terms after the five-year first terms. Ultrafined-grained steels were developed in lab-scale and/or in practical process. Basic approach has been performed to explore the evolution mechanisms of ultrafine-grained microstructures. There have been investigated two approaches to make the ultrafine grains: the "recrystallization route" and the transformation route. In the "recrystallization" route, heavy deformation at low temperature is necessary for the ultra-refinement. In the transformation route, making the high density of ferrite initiation sites in the deformed austenite, especially of the heavily compressed austenite structures, is essential for the ultra-refinement, and further hindering the ferrite growth is also inevitable to utilize the high initiation rate. Strength and toughness are dramatically improved by the ultra-refinement. Fatigue property is also excellent. The poor uniform elongation can be enhanced by the design of the second phase dispersion. At the same time the application has been also pursued from various viewpoints of engineering to take advantages of the ultrafine-grained steels. Bridge, ship, construction, automobile and other high strength parts are being attempted for the application.

Jan 1, 2004

By J. Budac, R. Kofluk, D. Belton, M. Sjogren

A series of tests were performed to determine the flammability limits of mixtures of oxygen, ammonia, steam and nitrogen, over a solution, in a sealed autoclave. The partial pressures of ammonia and oxygen in the vapour space were varied by adjusting the character of the solution and by adjusting the oxygen concentration in the oxidant gas respectively. The data shows that flammable conditions can be minimized by controlling the operating temperature, reducing the ammonia content in the solution, increasing the concentrations of Ni, Cu and Zn in solution and keeping the % oxygen in the gas phase less than 15.5. Observations were also made that suggest that the presence of an aerosol in the vapour space may hinder ignition.

Jan 1, 2004

By Q. Shi, Q. Feng

"The influence mechanism of chlorite on the flotation of pyrrhotite was investigated through flotation tests, Zeta potential measurements, optical microscope photos, solution ion measurements and absorption measurements. It is observed that, the addition of chlorite influences the flotation of pyrrhotite seriously. The IEP (isoelectric point) of pyrrhotite and chlorite is 7.6 and 4.3 respectively, in the condition of slight alkalinity, both pyrrhotite and chlorite are negatively charged, and the hetero-aggregation will not occur. With the existence of oxygen in solution, the iron ions are dissolved from pyrrhotite surface because of the oxidation of pyrrhotite during pulp conditioning. The dissolved iron ions adsorb onto the surface of chlorite in the forms of iron hydroxyl and iron hydroxide, and the adsorption results in the opposite charge of chlorite surface. As a result, the hetero-aggregation between pyrrhotite and chlorite occurs. The adsorption of chlorite changes the surface property of pyrrhotite and restricts the adsorption of amyl xanthate onto pyrrhotite surface, and then decreases the flotability of pyrrhotite.INTRODUCTIONIn sulfide ores processing, magnesium silicate bearing gangue minerals often report to the concentrate causing downstream processing problems as well as increased smelting costs. Talc,chlorite and serpentine are gangue minerals commonly encountered in complex sulfide ores (Engel, Middlebrook, & Jameson, 1997; Pietrobon et al., 1997; Witney & Yan, 1997; Chen, Grano, Sobieraj, & Ralston, 1999a, 1999b; Bremmell, Fornasiero & Ralston, 2005; Senior & Thomas, 2005; Wang, Somasundaran, & Nagaraj, 2005; WieseHarris & Bradshaw, 2007). All of them are characterized with uniform crystal structures consisting of silicon-oxygen tetrahedron and magnesium-oxygen octahedron. The magnesium-oxygen octahedron layers are broken during the liberation of serpentine to expose the magnesium-oxygen bonds with strong ionicity and hydration, which results in natural hydrophilicity of serpentine. In water, the hydroxyl on serpentine surface ruptures and dissolves into the aqueous phase while the Mg2+ remains, resulting in surface positive charge (Tao, 2012). As serpentine has a positive potential at alkaline condition, it is therefore likely that it will attach through electrostatic attraction to the negatively charged mineral surface and reduce both the flotation rate and recovery of target minerals (Lu et al., 2011). For talc, characterized as good natural hydrophobicity, the liberation comes from the interlaminar fracture to remain molecular bonds on surface with weak hydration. Being naturally hydrophobic, talc easily reports to flotation concentrates, thus reducing concentrate grade (Shortridge, Harris, Bradshaw, & Koopal, 2000; Beattie, Huynh, Kaggwa, & Ralston, 2006). Meanwhile, both molecular bonds and magnesium-oxygen bonds are exposed on chlorite surface when liberation occurs, resulting in moderate natural hydrophobicity between serpentine and talc (Tao, 2012). And thus the mechanisms of influence of chlorite on sulfide ores are more difficult to study."

Jan 1, 2016

By E. S. Moore

To properly understand industrial conditions in Spain it is necessary to consider the early history of the country. Spain is very backward in many lines. They use the sickle for cutting grain, and plows for cultivating the land, which resemble those of Biblical days. In the great mining camp at Bilbao only one steam-shovel is in use, although about two hundred million tons of ore has been produced, and this almost entirely from open cuts. It is the lack of industrial development, such as is found in many other countries, which permits large mining enterprises to be controlled almost entirely by foreign capital, although Spain is such an old country, and which permits mines opened in the days of the Phoenicians to still operate. Such deposits in America would be exhausted in a comparatively few years. The Phoenicians are supposed to have reached Spain about 1100 B.C. and to have worked some of the properties in the Rio Tinto district. The Carthagenians invaded the country about 236 B.C., and they were driven out about 205 B.C. by the Romans. The Romans ruled until 483 A.D., when they were overthrown by the Visigoths. Then, about 711 A.D., the Moors from Africa became prominent and they were finally expelled by the Spaniards in 1492. Spanish power reached its zenith under Phillip II, during the latter half of the 16th century, and since the close of that century the country has lost its prominent place among the nations. There are some evidences of revival in the development of good roads, the construction of a satisfactory network of railways, and the building of magnificent thoroughfares through the capital city, Madrid.

Jan 1, 1927

By H. L. Noblitt, Pauline Moyd, Louis Moyd

The deposit, which forms a ridge -adjacent to the York river, in Mont-eagle township, is held by Monteagle Minerals Limited, of Toronto. The ore is in a Precambrian gneiss which is composed of nepheline, scapolite, andesine and microcline feldspars, muscovite and biotite micas, and -corundum. The major orebody is tabular and is exposed for 1,200 feet along the crest of the ridge. It aver-ages about 90 feet in thickness, dips at about 70°, and was intersected by drilling at a vertical depth of 600 feet. The deposit was prospected for corundum in the early 1900's. Recent exploration was undertaken to deter-mine its potential as a source of high-alumina ceramic material, with by-product corundum and white mica. The program included prospecting, mapping, trenching, diamond drilling, bulk sampling, beneficiation research, a large-scale beneficiation test, product evaluation, market investigations, and plant design. Reserves, to a depth of about 300 feet, are estimated at about 3 million tons.

Jan 1, 1962

By Ken McIntyre, Trodel Wolf-Dieter

"Sirius Minerals is a UK based fertilizer development company focused on advancing into operation its polyhalite project in North Yorkshire, England. The operation is known as the Woodsmith Mine which has an estimated 2.7 Billion Tonnes of reserves and is currently in the construction phase. DMC Mining Services was selected to carry out the construction of four shafts for the project, a production shaft of 6.75m diameter to a depth of 1594 m, a ventilation shaft of 6.75 m diameter to a depth of 1565 m, and two additional shafts to support the construction of the material transport system (the MTS and Lockwood Beck intermediate) to 360m in depth for servicing the underground conveyor network for transport of product from the mine site to the costal port facilities located at Teasside. This paper will review the status of the project to date and the innovative approaches that DMC is utilizing to ensure a safe and successful shaft sinking project. INTRODUCTION The Woodsmith Mine in North Yorkshire is a Sirius Minerals-owned deep potash and polyhalite mine located near to the hamlet of Sneatonthorpe, Whitby in North Yorkshire, England, approximately 75 km east of York. The area of interest is more than 700 km2. The £3.2 billion project is to develop the Woodsmith Mine to extract polyhalite, and a tunnel system to transport it to a materials handling facility and harbour at Teesside. The site is the world's largest and highest-grade deposit of polyhalite and is expected to produce 20 million tonnes of polyhalite, potash and POLY4 per annum, as well as create over 1,000 direct jobs and many more indirectly. It has the potential to generate over £2 billion of annual exports for the UK. As the project will require mining to be undertaken in the North York Moors National Park, many objections were raised about the mine. Sirius Minerals has gone to great lengths to ensure that the project is sensitive to the local landscape, including: mineshaft head frames that will be positioned below ground to reduce their visual impact; surface buildings will be kept to a minimum; and the entire site will be landscaped and screened by existing woodland to blend in with the surrounding area. The project will also abide by strict environmental limits which govern our activity during the construction phase."

Jan 1, 2019

By V. Prasad, A. Afacan, K. Popli, S. Dubljevic

Froth flotation is one of the most common and widely used separation processes in the mineral processing industry; however, its complexity means that complete understanding of the process has not yet been achieved. A dynamic fundamental model is needed to enhance the understanding of the process and to improve process control. It is challenging to capture all the phenomena involved; hence, we propose a multiscale modeling approach with a framework ranging from macroscopic (equipment scale) to microscopic (attachment, detachment) models along with distribution models for ore particle sizes. Real-time froth properties are obtained using a vision-based sensing system. These measurements can be used for developing a soft sensor for grade using statistical methods such as PCR (principal component regression) and PLS (partial least squares) regression. The fundamental model is updated in real-time using extended Kalman filtering. Attachment dynamics are studied for different particle size distributions. The modeling and soft sensing is tested on batch flotation cell for the pure mineral galena with different particle size distributions using Xanthate and MIBC as collector and frother, respectively. The model, online measurements and soft sensor are useful in developing monitoring methods for froth flotation.

Jan 1, 2015

By Mike Anderson

The annual budget for the repair and maintenance of equipment at Syncrude Canada Ltd is in excess of 450 million dollars. Of this amount, a significant portion can be attributed to the loss of material on various pieces of equipment throughout the operation. In order to effectively battle the different wear and corrosion mechanisms that lead to material loss, it is important to understand how materials behave in the environments in which they are used. Through the work carried out at Syncrude, and work conducted with various external collaborators, significant improvements in both equipment reliability and productivity have been achieved. This paper will review some recent field trails where materials research has demonstrated the potential for significant improvements in equipment run life and reduced maintenance costs. These field trails will demonstrate the need for understanding the interaction between various damage mechanisms and the materials used in different services. The paper will also discuss current areas of focus along with future directions for further work.

May 1, 2003

By Marc-André Villiard, C. St-Onge, V. Silla, J-C Milot

Rio Tinto Fer et Titane (RTFT) operates a metallurgical complex in Sorel-Tracey, Canada. In the Ore Preparation Plant (OPP), ilmenite ore is roasted through four parallel rotary kilns generating 95% of the plant wide sulphur dioxide (SO2) emissions. RTFT proactively set an annual emission cap for SO2 to be achieved by 2015. To achieve this targeted SO2 reductions, a technology evaluation and selection exercise was carried out, followed by detailed engineering and implementation. After a detailed evaluation of SO2 scrubbing technologies, the Circulating Dry Scrubber (CDS) system was selected as the most appropriate desulphurization system for this application. The system was implemented and commissioned from 2013 to 2015. General performance testing conducted in May 2015 demonstrated that the system achieved and surpassed the anticipated design values in terms of SO2 removal efficiency and hydrated lime utilisation. This paper summarizes the SO2 technology selection process, design features of the selected technology, project implementation and final performance testing of the SO2 abatement system.

Jan 1, 2015

By D. Allen

Faced with decreasing ore grades and harder ores, many mines today are forced to become more efficient with their approach to processing. Variability in ore hardness, mineral liberation, reagent consumption, sliming, and leach responses are all a function of the minerals present and their concentration. Modern semi-automated X-ray Diffraction (XRD) analyses using Rietveld refinement techniques, in conjunction with high speed quantitative Near Infrared (NIR) analyses, provide reliable quantitative mineralogical ore profiling. By the implementation of XRD with NIR, mining, milling and leaching operations no longer need to be dependant on visual estimates for GeoMetallurgical Modeling and are provided with a valuable forecasting and production control tool. This paper will illustrate the development, plant implementation and application of XRD and NIR at several copper operations.

Jan 1, 2007

By T. H. Wilson

In 1901, the Crow's Nest Pass Coal Company, Limited, began producing industrial coke in 212 beehive ovens at Michel colliery. By 1908, 486 ovens had been installed and in that year 147,623 tons of coke were produced. Coke manufacture has been continuous from 1901 until the present time (1946), with total production of 2,795,402 tons. At present writing, only 100 beehive ovens are operating and production is reduced to 1,800 tons per month, due to the shortage of suitable labour. These ovens are drawn by hand, on contract, and the workmen are exposed to considerable heat. A man draws three ovens in eight hours, thereby producing approximately 1072 tons of coke per day. In addition to the inefficient and costly method of drawing coke in beehive ovens, tremendous losses are experienced in the wastage of gas and tar, which are driven off into the atmosphere. Also, the yield of coke per ton of coal fed to the ovens is low as part 9f the carbon is utilized in producing heat to carbonize the remainder of the coal. A recovery of only 55 per cent of the carbon, as coke, is obtained. The coking process takes place from the top of the charge, which is 21/2 feet deep, downward to the floor. Six and a half tons of coal are charged and 3.6 tons of coke are drawn from the oven after 72 hours' carbonization. The beehive ovens using Michel coal produce a very hard and tough coke, large in size and of silvery appearance, which has served the requirements of both foundry and smelter for many years. In 1938, the Company made a careful study of coking processes with a view to introducing a more economical method than beehive ovens and one that would be less dependent on skilled labour, the supply of which was rapidly diminishing at that time. Various methods of by-product coking were investigated, and it was decided that the Curran-Knowles process offered the greatest possibilities because of the low capital investment in relation to output and also because the horizontal oven design was suitable for an expanding coal. Consequently, a test on Michel B seam coal, supervised by Mr. E. Burrough, of the Fuel Research Department, Ottawa, was run in the Curran-Knowles plant at West Frankfurt, III. The results of this test led to the construction of a ten-oven battery of 32 ft. 6 in. by 8 ft. 3 in. Curran-Knowles ovens at Michel, which were completed in November, 1939. This battery was built as an experimental unit, with provision for an additional ten ovens if the coke proved satisfactory for the market. In 1942, an expanding coke market led to the construction of a second battery of ten ovens, which were completed in April, 1943.

Jan 1, 1947

By Xuehui Xia

Abstract -There are a number of sedimentary exhalative massive sulfide (SEDEX) deposits in the Proterozoic Langshan-Zhaertai rift at the western segment of the northern margin of the North China platform in China, including more than ten large, medium and small deposits located in a belt of 300 km EW by 50 km to 100 km NS, with large Cu, Pb, Zn, Ag, and S reserves. In several representative SEDEX deposits in the rift, the mineralizing elements are prominently zoned, horizontally or vertically, with Cu decreasing but Pb increasing from west to east, Cu decreasing but Zn increasing from bottom to top, and Zn restricted to the bottom half. The ore-hosting rocks, characterized by a clear manganese halo, have developed a polymetallic mineralization in positive relation with their carbon contents. Their isotopic aspects are: ?34S has relatively large positive values, fluctuating between +5‰ and +35‰, compared with Pb isotopic compositions which are less variable, with a model age of 1600 Ma to 1800 Ma, showing that they are mantle-derived. The mineralizing materials were associated undoubtedly with the contemporaneously faulting events in the rift. The deposits owe their origin to seafloor exhalation, with sedimentary rocks as their hosts.

Jan 1, 1999

By J. Keith Haddock

"Introduction The Coal Valley Mine is operated by Luscar Stereo (1977) Ltd. with the Alberta Energy Company having a minority interest. The mine produces 2.0 million tonnes of bituminous thermal coal per year. Deliveries include 1.5 million tonnes to Ontario Hydro and 0.5 million tonnes to the export market via bulk handling facilities on the west coast near Vancouver, B.C. There are a number of mining methods utilized at the mine including open-pit by truck and shovel, strip mining with large draglines and stripping with scrapers. The mine is located 100 km south of Edson, Alberta. Geology The coal measures are concentrated within a 210-metre int~rval of the Paleocene section. The coal seams were originally named by the mining companies in the earliest days of development of the area and these names continue to be used today. Of the five main seams, only three are presently economic to mine based on quality, thickness and depth of cover. These are the Val d'Or, Upper Silkstone and Mynheer. The Coal Valley Mine is located in the structurally deformed foothills area of Alberta and the structure of each mining area is therefore very complex. The general bedding strike is 305 degrees azimuth but major thrust faulting and folding has extensively deformed the natural seams as a closer examination will show. The Mynheer Seam, located at the base of the coal measures, ranges in thickness from 5 m to 10 m and has numerous bentonite and shale partings. Because of inherent geological features, the Mynheer Seam has been subdivided into two zones, the Mynheer 'A' and the Mynheer 'B', and the mining of coal in these zones has necessitated the utilization of distinctly different mining methods. The structural regime of the Mynheer 'A' zone consists of an overturned asymmetrical anticline crest containing a steeply dipping major thrust fault which has raised the seam above the present topographic level. Further extensive shearing and rotation of the coal has resulted in the coal taking a 'pod' shape. The Mynheer 'B' Zone is a continuation to the southeast along strike from the Mynheer 'A' Zone. The bedding dips to the southwest at an average of 12 degrees and is interrupted at the south end by a transverse fault and to the north by its outcrop at the surface."

Jan 1, 1985