Search Documents

By D. A. Cormode

"INTRODUCTIONPine Point Mines, operated by Cominco Ltd., is located approximately 55 miles east of Hay River, N.W.T. by the southern shore of Great Slave Lake.The milling operation commenced in the fall of 1965 at a design capacity of 5,000 tpd. An addition which came on stream late in 1968 raised the nominal capacity to 8,000 tpd. Currently the milling rate is 11,000 tpd.The lead and zinc sulphides occur in dolomite host rock. Typical feed grades at present are 2% lead, 5.5% zinc and 5 % iron. When dolomite is present even in relatively minor amounts in the zinc concentrate, it presents serious treatment problems and causes inefficient operation of electrolytic zinc refineries.By 1972, it had become apparent that magnesium rejection in the form of dolomite was deteriorating because of increased plant throughput of less amenable ore. This paper will briefly outline the Pine Point zinc flotation circuit and will discuss the two phase program for reducing the magnesium level in the zinc concentrate. The program included changes and alterations to the flotation circuit and the construction of an acid leaching plant."

Jan 1, 1977

By B. Jin

Removal of fluoride and chloride by alkaline washing from direct lead smelting dust which originated from an Ausmelt furnace is reported. The results show that the fluoride removal efficiency increases with an increase of alkaline concentration, alkaline washing temperature and time. The L/S ratio has little effect on fluoride and chloride removal efficiency. A new flow sheet for removal of fluoride and chloride from the dust was successfully proposed according to the results. Fluoride and chloride removal efficiencies are more than 53.68% and 63.18% respectively using the flow sheet under the optimum parameters of temperature 338 K, L/S ratio 3:1 and alkaline washing time of 1.5 h. The contents of fluoride and chloride in the alkaline washing residues can meet the standard of zinc purity as hydrometallurgical materials for zinc processing.

Jan 1, 2014

By D. Perednis

Fuel cells with thin samaria-doped ceria (SDC) electrolyte films deposited onto an anode support using spray pyrolysis were fabricated. The SDC films were deposited onto porous NiO-YSZ substrates at deposition temperatures between 400°C and 450°C. The influence of process parameters such as deposition temperature, flow rate, type of salt and salt concentration on the quality of the film was studied. A smooth dense film was successfully deposited using the precursor cerium ammonium nitrate and samarium nitrate dissolved in butyl carbitol (33.3 vol.%), 2-methoxy-l-propanol (33.3 vol.%), and ethanol (33.3 vol.%) solvent mixture. A deposition rate of 125 nm/h was achieved.

Jan 1, 2005

By Clermont Lavoie, Marc Filion, Marcel Vallée

"Les mineralisation d'or des gîtes de la SOQUEM - Silver Stack dans is canton Bousquet se situent dans une bands de roches pyroclastiques asides du groupe de Blake River, d'âge archéen, dans le même horizon géologique que lee gites aurifères de Thompson Bousquet et Dumagarni situés plus a rest. La propriété a été explores anterieurement a maintes reprises depuis les années 1930, parfois jusqu'aux travaux souterrains, notamment par les groupes Mooshla, Warrenmac et Westwood Cadillac ainsi que par Silver Stack Mines.Ces zones auriferes se situent a l'intérieur de larges halos (jusqu'à 1,000 m x 400 in) de pyrite disséminée (2-5%) dans des tufs a lapilli et des agglomerate acides montrant des concentrations locales de pyrite. La zone 1, découverte en vérifiant par sondage une anomalie E.M., coincide avec une de ces concentrations de pyrite et la teneur en or est ici proportionnelle a la pyrite. Ce secteur se distingue par l'intensité de l'altération en séricite. La zone 2, qui s'étend sur près de 600 m, se situe dans un agglomérat acids, avec une faible teneur en pyrite, et montre de fines veinules de quartz-carbonate.Du point de vue géophysique, aucune methods ne donne des résultats probants: la polarisation provoquée montre de tree grandee anomalies correspondant aux halos de pyrite, tandis que lee concentrations de pyrite détectées par les méthodes E.M. (VLF ou EMH) sont loin d'être toutes aurifères. Les relevés magnétiques aident a établir la structure la où un certain contraste de susceptibilité magnétique est present. Les essais minéralurgiques préliminaires indiquent que la concentration de Bette mineralisation aurifère ne présentera pas de problems majeur."

Jan 1, 1977

By E. M. De Souza, R. Penner

"Water is encountered at the majority of underground mines, both over their lifetime and during each stage of development and production. The dewatering system is one of the most important and costly components of an underground mining operation and it is often not well designed and analyzed. An effective design of a mine dewatering system will greatly reduce its energy cost as well as improve working conditions and reduce production costs. A computer-based system, called Qpump, has been developed to assist the underground operator to effectively design and/or assess over-all and local mine dewatering systems. The design features and principles used in the development of Qpump are introduced and an example which illustrates typical applications is presented.IntroductionTraditionally, dewatering operations have been given lower priority than many other operations in underground mining. Invariably water will be encountered during the sinking of the mine shaft, during development and subsequent production. The dewatering system thus becomes a very important component of an underground mine operation and, in fact, any mine manager will attest to the importance and necessity of an efficient mine dewatering system.The water problem is of varying importance at different mines. There are several factors that contribute to the water encountered. It is a function of the mining method and techniques utilized (backfill system, drilling and raising technology, dust control sprays, shaft water rings, etc.) and of prevailing conditions (ground water, rock structure and permeability). In some cases a mine may be so dry that little pumping is required while in others, the weight of water pumped may exceed by many times that of ore mined.The successful design and application of a mine dewatering system is dependent upon the operating conditions of each specific operation. There are no standard procedures and systems which can be used for all mining situations. However, an effective water system will greatly reduce the energy and production costs of a mine, improve working conditions and eliminate headaches because of flooded working places."

Jan 1, 1993

By G. Barrasso

REACH was proposed by the EU Commission in October 2003 and stands for the Registration Evaluation, Authorisation and Restriction of Chemicals. It requires that all substances identified as persistent, bio-accumulative and toxic, whether the risk of those chemicals being released is real or perceived, require registration prior to them being allowed to be imported into the European Union. An internal investigation by the metals industry indicates that almost all primary raw materials streams would be classified as hazardous due to the potential health or environmental hazard properties of one or more of their ingredients. REACH uses a wide definition for chemicals and metals and as such its implications greatly impact the entire supply chain of the metals industry. The process of registration would require the producer/ importer to produce a dossier. Initiatives along the same lines as the EU REACH are also coming up in other parts of the world. REACH requires registration of at least four substances manufactured by the aluminium industry: aluminium metal, including powder, aluminium oxide, and aluminium hydroxide. The proposed legislation permits the affected companies to band together to form a consortium to develop certain aspects of the registration application. The aluminium industry has established a consortium and testing is currently underway.

Jan 1, 2006

By L. W. Hamel

"Two 35 foot diameter enviro clear thickeners were tested in series as CCD units from June until October, 1978. Up to shutdown in July, we ran with automatic bed level control via the level probes and underflow pinch valves. Despite extensive efforts, we were unable to eliminate the surges created between the units by the opening and closing of the pinch valves. Early in July, the best rake speed and gap setting were determined. After shutdown, the enviro clears were run by manually controlling the pinch valves. These efforts were successful.A few mechanical problems were encountered while operating the thickeners. New units should incorporate more support for the drive coupling and a rubber feed seal. A few modifications of the instrumentation control scheme will be required before the units can be fully automated. A less sophisticated automatic flocculant addition system will accomplish the desired results. Control of the underflow withdrawal via the pinch valve should be investigated further. Our best results were obtained by keeping the feed volume to the No. 1 enviro clear constant. Surges were controlled by opening or closing both underflow valves proportionately.Capacity of the enviro clears is dependent of many variables. The ore treated during the test program was much finer than that reported on in R & D Project Report 76-02. Conditions were never steady enough to determine best flocculant dosage or addition point(s). The lowest soluble losses were obtained at very high wash rates. The underflow densities drop but the soluble losses also drop. Regression equations were developed in order to assess the effect of the various parameters. Within the range studied, these equations will predict the performance of enviro clear thickeners as CCD units on Elliot Lake ores. Our results show that the enviro clear thickeners are a viable alternative to the conventional CCD thickener."

Jan 1, 1979

?Introduction to the Delphi Group ?Why is carbon important to your organization ?Key elements of a carbon management strategy ?Inventory ?Risk & opportunity scan ?Mitigation options and financial mechanisms ?Identify targets and develop policy ?Communication and improvement ?Manage for success

May 1, 2009

By M. H. Colebrook

Nickel laterites contain about 70% of all continental or terrestrial nickel resources; therefore the recovery of nickel from lateritic ores has large economic significance. The processing of lateritic ores involves the preparation and movement of concentrated aqueous suspensions. However due to complex characteristics and non-Newtonian properties, ranging from shear-thinning to shear-thickening and from thixotropic to rheopectic, a basic understanding of the flow behaviour must be developed. This understanding will assist in the development of new plants and the operation of existing plants. The work in this paper involves the characterization of three ore types from the Vermelho ore deposit to categorize them as rheologically simple to complex. Rheological testing was also conducted on pure mineral samples that represent the main minerals in these samples. The results show that the rheological properties of the ore types can be related to the surface properties and physical characteristics of the main mineral constituents.

Jan 1, 2006

By J. A. C. Ross

Introduction To enlighten those who may be wondering where anyone could find sufficient data to write a paper on underground concrete work, the author would like to explain that, at Copper Mountain, we have found it necessary to line numerous headings with a layer of concrete in order to keep them in a safe and serviceable condition. The majority of these headings are scram drifts and ore-pass raises. This paper will therefore deal, in the main, with the methods of and reasons for placing concrete in these headings. During recent years, radical changes have been made in the methods of mining ore at the Copper Mountain mine. After considerable experimenting, a mining system has been developed making use of diamond drills for primary breaking and transfering such broken ore through scram drifts with slusher hoists. With the advent of scram drifts, it soon became apparent that some substantial means of reinforcement and protection for the scram drifts themselves would be necessary. Since the orebodies in this mine are cut by numerous dykes or faults, and often both, it was anticipated that some means of support would be required where headings necessarily passed through these incompetent zones. Further, as experience was gained, scram drifts were driven into pillars and in close proximity to old workings so as to recover the maximum amount of ore. In such places, the ground is often severely fractured, either as a result of previous mining or from the effect of excessive rock pressures.

Jan 1, 1950

By Jan E. Nesset, Phillip J. Mackey, Joo Y. Kim, Giovanni Di Prisco, André R. Laplante

Understanding the appropriate gold recovery to associate with copper recovery when assessing laboratory testing on porphyry deposits is often complicated by several factors including variable and/or complex mineralogy, and the variability contributed by the low Au content of the various flotation products. As a result, gold recovery is often underestimated and the value contributed by the gold to project economics is less than it should be, a problem that could influence overall project viability. Typically, for these types of deposits, the gold recovery is found to be lower than the copper recovery. In this unique project, having the objective of seeking a better understanding of gold recovery relative to copper recovery, mill feed samples from a selection of six operating world-class Cu-Au low-grade deposits were collected along with the mill metallurgical results for the corresponding sample periods. The samples were subjected to laboratory flotation tests, as well as the Laplante gravity recoverable gold (GRG) test, mineralogical assessment and cyanidation leaching. The aim was to better understand the copper and gold recovery relationship, the links between laboratory and plant flotation performance, the influence of mineralogical differences, and the potential for enhancing gold recovery by gravity recovery techniques. A new correlation of copper and gold recoveries based on the results is presented in the paper. The results showed that the link between copper and gold recoveries established in the best laboratory tests were maintained in the plant results, and further, that the potential for improving Au recovery by gravity or flash flotation methods is directly proportional to the amount of gold greater than 75 microns.

Jan 1, 2005

At the end of a century of mining education in South Africa, it is appropriate to reflect on the past, take stock of the present and ponder the future of mining education. While it is likely that changes in the mining industry will generate an increased demand for mining graduates, the number of suitably qualified applicants to study mining is worryingly small. While good progress has been made in unifying the educational system that previously provided schooling on a racially separate basis, it appears that a decade or more will be required to raise competency levels in mathematics, science and English, and this paper describes the process as it affects mining engineering programs. It also describes the initiatives currently being undertaken by the University of the Witwatersrand and the mining industry to ensure that the South African industry receives an adequate flow of well-qualified mining graduates, despite more than 70% of the intake coming from severely disadvantaged educational backgrounds.

Jan 1, 1999

By F. Chiesa

The permanent mould process, which is a favoured process for producing premium quality aluminium casting, is rarely used to produce magnesium alloy parts. This may be attributed different factors such as: the reservation with which the automotive industry considers using magnesium in structural castings; also the relative hot shortness of most magnesium alloys when compared to aluminium A356/357 is another factor. A third reason stems from the fact that the "heat content" of magnesium is much less than that of aluminium, resulting in the difficulty, for a relatively slow process such as permanent mould (versus pressure die casting), to reach a mould dynamic equilibrium temperature sufficiently high to avoid premature freezing and misruns. The present work will address this problem by carrying out controlled cycling of a laboratory mould, poured with aluminium and magnesium alloys. The influence of insulation of the mould and artificial electric heating on the run-in mould temperature will be determined experimentally. A thermal model will be sought for these thermal devices that will allow to predict the thermal behaviour of moulds of different geometry before a single casting is poured. The model will be tested on an industrial casting in a workshop environment.

Jan 1, 2006

By Knut F. Garshol

Quality and durability of sprayed concrete depends on the concrete mix design, the type and use of accelerator and all the aspects of the placement onto the rock surface in the underground working. A large number of influence factors are involved and they must be managed for a successful and durable permanent sprayed concrete structure to be produced. The paper discusses some of the central issues, including how to view the long-term effects of chemical admixtures and accelerators in wetmix sprayed concrete. Permanent lining sprayed concrete for rock support is increasingly being used today and the durability can be equally achieved as for any other concrete.

May 1, 2003

By Guoxiang Chi

The Cornwallis Fold Belt in the Canadian Arctic Archipelago contains numerous Mississippi Valley-type (MVT) Zn- Pb occurrences and the world-class Polaris deposit. The occurrences are mainly hosted by the dolostone in the Thumb Mountain Formation which spreads over 25000 km2. Success in exploration requires further understanding of the genesis of these occurrences and an assessment of their parentage with the giant Polaris deposit. Syn-sulfide dolomites in regional occurrences share C-O-Sr isotopic characteristics similar with Polaris dolomites, indicating warm basinal brines enriched in 87Sr. The dolomites and sphalerites contain fluid inclusions with ice-melting temperature between ?45° and ?25°C, which is significantly lower than for most MVT districts in the world (?30° and ?10°C). These characteristics indicate that all the Cornwallis occurrences were produced by fluids of the same sources and/or aquifers. The deposit size was largely controlled by the rate and duration of the metal-carrying fluid flow, and by the availability of reduced sulfur at the site of mineralization.

May 1, 2001

By Y. Turen, Y. Karakas, E. Candan, C. Sahinturk

In this study, wettability between sprayable tundish lining (MgO) and molten steel was investigated by using sessile drop method. Content of glass fiber (SiO2) in the MgO varied between 0 to 8 wt% whereas mean particle sizes of the MgO were 25, 75, 150 and 300µm. Experimental results revealed that contact angle (0) of sessile drop on the MgO was not altered by the addition of glass fiber up to 1 wt.% whereas above 2 wt.% addition decreased the 0 considerably. Contact angle, 0, increased considerably with increasing MgO particle size. SEM analysis showed deposition of glass phase was present at the interface as the finer MgO particles were used.

Jan 1, 2004

By Tamas Kekesi, Gergo Rimaszeki, Tibor Kulcsar

The efficient purification of soldering waste material can be achieved in a single operational step by the electrolytic refining in pure hydrochloric acid - tin-chloride media. The complex formation of the ionic species may offer a beneficial level of natural inhibition. Using the PCR (periodic current reversal) technology, is efficient in affecting the morphology of the cathodic deposit. In order to optimize the process, the investigation of the solution stability and the electrode reactions is essential. The natural tendency of the Sn(II) oxidation and precipitation can be overcome by properly controlling the concentration of the main components and the ratio of Sn(IV)/Sn(II) in the electrolyte solution. Polarization curves were obtained for different concentrations tin and hydrochloric acid. Conclusions referring to the electrode reaction were derived from the overvoltage - current plots. The morphology of the deposit can be correlated with the exchange current density, also determined from the polarization curves. The cathodic current efficiency and the morphology of deposited metal are affected by the distribution of tin species and the principal electrolysis parameters.

Jan 1, 2011

By Terry A. Kirk

"This paper describes Derrick High Frequency Vibrating Screens and their process performance in grinding circuit applications. The benefits of screen sizing in closed circuit grinding are illustrated by case histories from a wide spectrum of mineral industries.INTRODUCTIONHigh capacity, reliable wet screening equipment is increasingly in demand by the mining and allied industries for separations finer than 1/.7 5mm (I/ mesh). The continuing search for improved energy efficiency and reduced steel consumption in comminution has Jed to greater scrutiny of every aspect of circuit design and operation, including the classifier efficiency (selectivity) function.Derrick Manufacturing Corporation has been developing high frequency screening machines designed specifically for grinding circuit applications since 1973. Successful installations are currently operating in iron ore, copper, coal, uranium, phosphate and other extractive industries."

Jan 1, 1984

By Chris Blain

"Abstract - Based upon an extensive database, this paper analyzes the record of modern mineral exploration success and establishes the 50-year trends in discovery. The record clearly shows that the overall discovery rate rose during the 1950s and 1960s, peaked in the 1980s, and fell during the 1980s and 1990s. By commodity and ore-type target, the pattern of discovery is not continuous. Typically, it is episodic as a series of waves with minor resurgence. The waves reflect the order of the so-called discovery booms, led by uranium, then nickel, and copper, polymetallic base metals and gold. With the possible exception of gold, the discovery booms appear to be independent of metal price, although favorable perceptions of the price outlook may well have initiated the boom or led resurgence. Although difficult to quantify, an emerging trend in modern discovery is the integration of several detection techniques into the search process. No doubt, this trend will continue as orebodies become more and more difficult to find. The record of the past two decades shows that greenfield discovery rates have progressively fallen even though the level of investment in exploration has risen to an all-time high. This trend reflects increasing discovery risk. Several factors are contributing to this trend. Perhaps the two most important are: (1) deteriorating economics as increasing real costs and decreasing real prices continue to raise the economic hurdles for minimum acceptable exploration targets, and (2) increasing exploration maturity in many search terrains, particularly those in the traditional regions of North America and Australasia. To succeed cost-effectively in this new environment of increasing discovery risk will require extraordinary creativity, innovation, and technical skill coupled with commercial discipline."

Jan 1, 2000

By Jianping Zhang

QUESTIONS: ?? Is it more expensive to find an ounce of gold in Canada today than 50 yrs ago? ?? Did the Canadian gold industry find more gold than they mined? ?? What is the future sustainability of the Canadian gold industry? ANSWERS: ?? The gold discovery costs in real terms only increased slightly from 1946 to 2000. ?? Though the Canadian gold industry mined more gold than they discovered in the period, when undeveloped deposits are taken into account, the deficit was merely 12 million ounces. ?? The Canadian gold mining industry would be sustainable in the foreseeable future, particularly, given the overwhelming predicted promising gold market in the mid/long run.

May 1, 2006