Search Documents

In the leaching and recovery of gold from copper containing gold ores using cyanidation, some copper minerals also dissolve which can have a detrimental effect on the process efficiency and economics. There are also environmental concerns with current operations discharging cyanide and copper cyanide species into tailings dams, and strict regulations prohibit this for greenfield plants. Cyanide destruction however is not an economic option for new plants treating copper-gold ores. This paper evaluates a potential recovery process to overcome the copper cyanide problem. Despite gold dissolution occurring in copper cyanide solutions having no free cyanide, gold recovery from ores is lower compared to free cyanide. Thus, cyanide addition has to be optimised to maximise the gold recovery whilst endeavouring to eliminate free cyanide at the completion of leaching (CN:Cu less than 3:1). Subsequently, copper cyanide can be recovered using activated carbon. The loaded copper cyanide is easily recovered from the carbon with a cyanide soak and distilled water wash such that the eluted CN :Cu ratio is less than 4:1. The copper could be recovered efficiently by electrowinning, by decreasing the pH of the eluant to 5. The remaining cyanide solution, after electrowinning, is then neutralised to form NaCN and recycled.

Jan 1, 2005

By A. Ashrafi

The electrochemical deposition of polypyrrole coating on different pretreated aluminum-alloy 7075 substrates was carried out using cyclic voltammetry, The pretreatment of specimens consisted of mechanical polishing and/or electrochemical etching, In the latter case, an aqueous solution of phosphoric acid and ethanol was used, The electrodeposition solution was 0,25 M pyrrole and 0,1 M oxalic acid in double-distilled water, The cyclic voltammetry scan rate used was 700mv/s, Morphology of the coatings was examined using scanning electron microscope (SEM), Using the Tafel experiment, corrosion resistance of the coated substrates was investigated in 0.1 M NaC1 solutions, Results obtained revealed that electropolymerization of polypyrrole on 7075 aluminum alloy would increase the resistance against corrosion in 0,1M NaC1 solution, Also it was observed that, compared with mechanical polishing, electroetching pretreatment would be more effective.

Jan 1, 2005

By Leonardo Flores

"Minera Escondida operates two open pits on a porphyry copper district, southeast of Antofagasta, Chile. During 2005, ore will be delivered exclusively from one pit to two concentrators, while from 2006 both pits will provide ore to these plants. Annual testing programmes on drillhole samples, have allowed for the construction of hardness block models since 2000. These models have delivered two main hardness descriptors, the Bond work index and the SAG power index. These parameters and plant operational specifications have been used as input information to forecast, the expected throughput and ball mill product size (P80) for each block of ore. Two forecasting techniques have been used, an in house model, strongly dependant of bond work index and MinnovEx´s CEET2, dependant of Bond work index and Sag power index and other parameters. Model performance has been evaluated from reconciliating on a monthly basis, the forecasted throughputs against a recalculated plant throughput which accounts for losses in tonnage not caused by ore hardness but instead by unscheduled plant operation problems. The model performance for 2003 was ± 2% yearly and ± 5% quarterly, well within the expected ± 3% and ± 10%. INTRODUCTIONThe Escondida porphyry copper district is located 140 km SE of Antofagasta, Chile at 3150 m.a.s.l, at 24°16’ South latitude and 69°04’ West longitude (figure 1)."

Jan 1, 2005

By Frank Cappuccitti, James A. Finch, Stéphanie Gélinas

"A colorimetric technique, originally developed for methyl iso butyl carbinol (MIBC) based on the Komarowsky reaction, has been extended to a wide range of common mineral flotation frothers. The procedure, which is briefly described, is shown suited to on-site determinations in a campaign at Kennecott Utah Copper Copperton Concentrator (Rio Tinto). Some observations are described, including: frother (MIBC) concentration evolution down a bank, frother distribution between pulp and froth phases, and loss of frother over time due to adsorption on certain minerals. A possible interference with a fuel oil addition was overcome. MIBC in recycle water was also measured.The ability to monitor frother easily will help interpret gas dispersion behaviour and should permit further optimization of flotation cell hydrodynamics and chemistry. The capability to directly measure should help optimize the type, amount and location of frother addition, and to assess frother recycled with reclaim process water.INTRODUCTIONOwing to the lack of analytical methods, the task of determining frother concentration in plant flotation circuits is not routinely performed. Industrial sites seldom outsource analyses that are both costly and inconvenient, due to the necessity of shipping freeze-dried samples to remote testing facilities. A more direct colorimetric method has recently been demonstrated for the laboratory characterization of common industrial frothers (Gélinas and Finch, 2004). The approach, based on the Komarowsky reaction (Penniman et al., 1936; Coles et al., 1942; Duke, 1947), was previously described by Parkhomovski et al. (1976) for methyl iso butyl carbinol (MIBC). The reaction involves the interaction of the OH group of a higher alcohol, concentrated sulphuric acid, and salicylaldehyde, to yield coloured solutions with intensities that can be analyzed by UV-visible spectrophotometry."

Jan 1, 2005

By A. N. Kumar

Two fabrication stages in the manufacture of pipelines are identified as causing significant deterioration of the steel plates, namely cold bending and welding. The objectives of this work include quantitative assessment of the degradation of the quality of the steel plate by the loss of fracture toughness, and an estimation of the safe working pressure. The study was conducted on three API grade steels: X42, X46 and X60. After cold bending by the UO technique, various welding technique were employed for joining of the bend plates along the pipe length. A crack-tip opening displacement parameter (CTOD) was used at the onset of initiation and at the first load maxima as the criterion for assessing the toughness degradation under various fabrication stages and regime (such as WZ, HAZ and parent body). In addition, strength, hardness and impact energy values were determined to check the degree of degradation. Microstructural and microfractographic investigation of the fractured samples were also carried out in the scanning electron microscope (SEM). X60 grade steel plate suffers from CTOD toughness loss by around 38 and 55% after welding and cold bending, respectively, for the conditions studied. A combined effect of the two stages results in a loss in toughness by around 70% for the same steel. In X42 grade, the loss in impact energy ranges from 78 to 35 J due to electrical-resistance welding study (ERW). Crack resistance curves are also obtained for the steels to study the crack growth resistance behaviour and to supplement the information on crack initiation behaviour. The orientation of the pearlite banding, as observed on the fracture plane with respect to notch front and applied loading direction appears to have a strong influence on the microvoid-coalescence mechanism of fracture as well as the toughness values. An integrated analysis of the performance of pipelines, considering all these key factors, is discussed.

Jan 1, 2005

By S. Felderhof, W. S. Vaughan

"Over the years, it has been increasingly difficult for the minerals industry to raise the necessary capital for its activities. To alleviate this phenomenon, complete transparency and capital market efficiency is needed. Since a company’s mineral resources and mineral reserves base is an essential component to obtaining capital, reporting these assets must also be transparent and efficient. This must occur, however, at an international level given that mineral industry operations, and its financing, are international. To achieve this, an international committee (i.e. Australia, Canada, South Africa, the United Kingdom and Europe, and the United States) was formed and has been developing standards for the reporting of mineral resources and mineral reserves.The effectiveness of these standards, however, depends on adoption by the required regulators. Unfortunately, these standards have not been recognized by the U.S. Securities and Exchange Commission (SEC). Instead, the SEC adheres to its old standard (Industry Guide 7), making it increasingly expensive and difficult for international mining companies to obtain capital in the United States. Compounding the problem is the SEC’s influence over the current work of the International Accounting Standards Board and the International Organization Organization of Securities Commissions. These organizations are in the process of standardizing international accounting practices and international securities rules and regulations. Their current position may prevent adoption of the industry-developed mineral resources and mineral reserves standards which are internationally recognized."

Jan 1, 2005

By B. Arsenault

Aluminum coatings can provide galvanic cathodic protection for several metals and alloys, In order to be a suitable protective solution on structural components, the mechanical integrity of the component must be preserved, In particular, fatigue properties are a challenge for thermal-spray protective coatings on mechanical structures, To address the issue of the fatigue integrity of 7075 aluminum alloy with an arc-sprayed protective coating, different surface preparations prior to arc spraying were considered, In the present work, a feasibility study was performed using laser ablation as a surface-preparation technique before or during arc spraying of coatings, This was collaborative effort between the LERMPS laboratory in France, the National Research Council Canada and the Royal Military College of Canada, Both fatigue and adhesive properties of aluminum coatings were evaluated in relation to substrate-surface-preparation techniques including laser ablation (Protal® process), grit blasting and shot peening. Results indicate that a combination of key conditions, including the use of nitrogen as the arc spray gas, shot peening, and proper laser energy density for ablation, provide high fatigue resistance of metallic coated 7075 alloy substrates. Specimens prepared under these conditions show a similar fatigue resistance to uncoated substrates.

Jan 1, 2005

By V. I. Birss

Planar solid oxide fuel cells (SOFCs) offer great promise as stationary power generation devices, primarily due to their flexibility in terms of fuels, high energy conversion efficiency (when both electricity and heat are captured), and their relatively low fabrication costs. However, the anode performance can be compromised by such factors as exposure to certain sulfur-containing fuels and the deposition of coke when using hydrocarbon fuels. In terms of the cathode, its performance is limited primarily by the slow kinetics of the oxygen reduction reaction, while its lifetime can be negatively affected by factors related to the corrosion of currently used stainless steel interconnect materials. This talk will present an overview of these challenges and some possible solutions to these problems. The presentation will also focus on how electrochemical methods can be used to evaluate and improve the performance of SOFC anodes, cathodes, and interconnect materials. In addition, recent promising research efforts directed towards performance enhancement of SOFCs through the use of nanoscale electrocatalysts will be discussed.

Jan 1, 2005

By K. B. Hodgins, P. Ouellette

"The North American mining industry faces challenging emissions regulations in the coming years with the introduction of new standards for off-road diesel engines. In order to remain competitive, industry stakeholders must invest in new technologies that are economically and environmentally sustainable.Westport Innovations Inc., Vancouver,British Columbia, has developed high-pressure direct injection (HPDI) technology that allows diesel engines to run primarily on natural gas with no intrusive engine modifications while reducing emissions of nitrous oxides (NOx), particulate matter (PM), and CO2 with no loss in performance. This is accomplished through late-cycle, high-pressure direct injection of natural gas into a diesel engine combustion chamber at the end of the compression stroke. A small amount of diesel fuel is injected first to initiate combustion, followed by the natural gas fuel main injection. The diesel cycle and its operating characteristics are fully retained including high combustion efficiency, lowspeed torque, high-power output, no engine knock, and fast response to load changes. Natural gas has not been an attractive fuel alternative in mining operations due to the reduced performance associated with spark ignition engines and the added weight and space required for compressed natural gas tanks. However, liquefied natural gas (LNG) can be stored with less impact on weight and space than compressed natural gas (CNG) by virtue of its increased energy density over CNG.Westport has applied HPDI technology to the Cummins QSK series engines for high horsepower applications such as power generation and mine haul trucking. HPDI can also be applied to other engine manufacturer platforms and market applications. Westport is interested in demonstrating the unique characteristics of HPDI in mine haul trucks to show diesel performance with low emissions levels using low-cost LNG fuel.Retrofitting a Tier 1 engine with HPDI would provide emissions reductions below the EPA 2006 Tier 2 standards while maintaining the performance and efficiency of the Tier 1 platform. The longer-term target is the Blue Sky voluntary standards of 3.8 g/kW-hr (2.8 g/bhphr) of NOx + non-methane hydrocarbons (NMHC), and 0.12 g/kW-hr (0.09 g/bhp-hr) of particulate matter (PM) and future standards. Typically, an HPDI engine is capable of reducing NOx emissions by 40% over diesel operation at the same efficiency. On a mining truck meeting Tier 2 standards, this NOx reduction would translate into NOx emissions approximately 14 t per year lower than under diesel operation. PM emissions are typically reduced by some 60% with HPDI fueling, which would translate into a yearly reduction of 650 kg. Similarly, engine-out greenhouse gas (GHG) emissions are reduced by 21%, resulting in a yearly reduction of approximately 950 t per vehicle.Above those of emissions reduction, efficient natural gas usage in mine haul operations would offer significant benefits in terms of fuel cost savings, which may be further combined with monetary emission credits. HPDI technology would enable operators to exercise environmental stewardship while gaining a competitive advantage in advance of new Tier 2 and Tier 3 emissions regulations. The advantages of natural gas use among mine haul truck operations can be replicated across a broad range of engines and applications."

Jan 1, 2005

By C. -S. Xie, J. -H. Kong

The microstructure and mechanical properties of X80 hot-rolled thick steel strips with a thickness of 17.5mm produced in Wuhan Iron & Steel Company (WISCO) are introduced in the paper. The steel strips as fabricated through proper thermomechanical processing (TMP)/ on-line accelerated cooling (OLAC) processing have shown high strength and toughness, low brittle transition temperature, good weldability, and high Shear Area (SA) percentage in Drop Weight Tear Test (DWTT). The microstructure of the steel strips is characterized with mainly acicular ferrite, and fine dispersed Martensitc-Austenite (M-A) phases. It is determined that the mechanical properties are improved due to the presence of the fine M-A phases and precipitates, which could be formed by reducing the finish rolling and coiling temperatures.

Jan 1, 2005

By P. -Q. Wu

A modified electrochemical noise (EN) technique has been applied to monitor corrosion wear of TiN-coated ASP23 steel and TiN-coated AISI 316 stainless steel sliding against corundum in 0.5 M H2SO4. Experimental results show that the EN technique can sensitively detect potential and current variations during a corrosion-wear process. Corrosion-wear mechanisms of TiN coatings depend on their substrate properties. If the substrate is passive, such as AISI 316 stainless steel, the potential and current variations reflect the properties of the coating. Depassivation and repassivation alternately take place on the tribo-activated wear area during the steady-state phase. If the substrate is active, such as ASP23 tool steel, the electrochemical noise is dominated by dissolution of the substrate at the pinholes and the hydrogen evolution all over the exposed surface.

Jan 1, 2005

By R. Baker

A novel electrochemical half-cell and corresponding working electrode were designed to evaluate the electro-catalytic activities of catalysts in an environment close to that of an operating proton exchange or polymer electrolyte fuel cell (PEMFC). Cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) techniques were employed using the novel cell to characterize various methanol electro-oxidation parameters that contribute to the overall reaction on a fuel cell anode. The effect of temperature on methanol oxidation kinetics was examined in the potential range of 0.31 to 0.65V (vs. NHE). The data was collected in the temperature range of 20 to 80°C. Based on the experimental analysis and literature data, an equivalent circuit model (ECM) for methanol oxidation was proposed and was used to fit the EIS experimental data. The experimental data and ECM electrochemical data was used to extract electrochemical kinetic parameters for methanol oxidation such as the exchange current density, Tafel slope, and energy of activation for the reaction. Kinetic data, especially at different temperatures, is very limited in the literature.

Jan 1, 2005

Proper water and thermal management is essential for obtaining high performance of Proton Exchange Membrane Fuel Cells (PEMFCs). A steady, two-dimensional water and thermal management model was developed, aiming at considering pressure drop, open circuit voltage variation with stack temperature, water vapor effects on membrane conductivity, which made the model physically more reasonable and more suitable for various operating conditions. The model could predict the distributions of a series of important parameters along the flow channel, and thus the effects of various operating and design parameters on the fuel cell performance could be investigated easily by numerical trial-and-error method. The modeling results compared well with the available experimental results from the literatures. The results also showed that the humidification is crucial for the performance of PEMFCs. The model could be a very useful engineering tool for the optimization of PEMFCs.

Jan 1, 2005

By J. Malone, D. Loth, J. Palmer

WMC Resources' Kalgoorlie Nickel Smelter was commissioned in 1972 at a design capacity of 30,000 tpa of contained Nickel in matte. A series of upgrades and progressive improvements have resulted in a design capacity increase to 110,000 tpa of contained Nickel in matte. The smelter sources nickel-in-concentrate from three Mine / Concentrators and supplies nickel-in-matte to WMC's Nickel Refinery and export customers. The Flash Furnace was last rebuilt in 1999, and is over halfway through the 10-year campaign target. The many modifications over the previous campaigns, including the Integrated Flash Furnace, are reviewed. Recent operation of the smelter and the development of the process during the current campaign are detailed herein. An overview of key interfaces with the Nickel Business Unit Concentrators and Refinery operations is provided.

Jan 1, 2005

By S. Schwartz, T. Bilney

"Over recent years a number of techniques have been developed as part of the AMIRA1 P9 project to represent mathematically or measure directly sub-processes occurring in flotation cells. These include the determination of:•,?a machine parameter (bubble surface area flux, Sb);•,?a froth parameter (froth recovery, Rf );•,?entrainment and drainage parameters (???and d); and•,?an ore floatability parameter (Pi).These flotation parameters allow the plant engineer to develop a model of the flotation circuit that can be used as a powerful tool to diagnose the performance of that circuit. The recently developed JKSimFloat V6 flotation simulator uses these parameters to predict the flotation circuit performance that would arise from changes in operating conditions and circuit configuration.This new flotation technology was applied to the Placer Kanowna Belle Gold Mine in Western Australia. A series of plant surveys, cell characterisation measurements and laboratory batch tests were conducted to determine the flotation circuit model parameters to be used within the JKSimFloat V6 simulatorA thorough flotation circuit analysis was then performed at Kanowna Belle using JKSimFloat V6. The recommendations that were provided by this circuit analysis have resulted in large improvements in the flotation performance at Kanowna Belle. These include a 1.3% increase in flotation gold recovery and a substantial decrease in operating costs. The analysis is still ongoing, however, the benefits already obtained from applying this technology have resulted in a US$1.3 million a year improvement to the mine."

Jan 1, 2005

By A. C. Hatton

Doped SrCoO3.8 was found to be a promising material for use as a cathode component in intermediate temperature SOFCs. In this work, strontium cobaltite ceramics doped with 10 mol% to 90 mol% samarium were synthesized using the glycine nitrate process in order to study the electrical conductivity and thermal expansion at temperatures of up to 800°C. As-synthesized powders were deagglomerated, pressed and sintered at temperatures ranging from 1100-1250°C. The effect of temperature and composition on electrical conductivity and thermal expansion are presented and discussed.

Jan 1, 2005

By D. H. Schwarz

The performance of proton exchange membrane (PEM) fuel cells depends on catalyst layer composition and structure. Experimental observations reveal that state-of-the-art catalyst layers consist of microporous agglomerates of carbon-supported catalyst sites bound together by polymer electrolyte. In between the agglomerates are macropores which provide pathways for the transport of gaseous reactants. In this work, three-dimensional, multicomponent and multiphase transport computations are performed using a computational fluid dynamics (CFD) code (FLUENTTM) with a new PEM fuel cell module, which has been further improved by taking into account the detailed composition and structure of the catalyst layers using a multiple thin-film agglomerate model. In this model, it is assumed that thin films of polymer electrolyte and liquid water surround the catalyst sites. The results of CFD computations show that transport limitations associated with the thin film of polymer electrolyte and the presence of liquid water in the catalyst and gas diffusion layers have substantial negative effects on PEM fuel cell performance. Also, the results of computations with variable distributions for a given precious metal loading show that, in general, uniform catalyst loading provides the best fuel cell performance.

Jan 1, 2005

By D. Chadwick, J. W. Matousek

Between 1860 and 1890 -- from the time of the American Civil War to the last decade of the 19th Century -- nickel production in North America was dominated (even monopolized) by the output of the industrial complex of the Gap Nickel Mine near Lancaster, Pennsylvania and the American Nickel Works in Camden, New Jersey. In some years, from one sixth to one third of the world's metallic nickel supply came from this enterprise. Mining and smelting were conducted at Lancaster; a matte of high iron content was shipped to Camden for pyrometallurgical and hydrometallurgical refining to produce nickel metal, copper sulfate, and cobalt oxide. The high purity nickel product was rolled into sheet for marketing, primarily for coinage, as nickel had few other uses at that time. The undertaking experienced all of the problems that face the mining and metallurgical industries of today: declining reserves, high labor and fuel costs, high transportation costs, fluctuating demand and prices, pollution concerns, and foreign competition. The technical features of the geology; the mining, smelting, and refining operations; and some of the economic aspects are assessed. The view is taken from that of the present time -- seeking those lessons from history that we are supposed to learn or face the prospect of repeating the mistakes of the past.

Jan 1, 2005

By Z. Xie

Gas diffusion electrodes (GDEs) for high temperature polymer electrolyte fuel cells (PEFCs) have been prepared using ZrP-modified Nafion ionomer. The performances of these GDEs as cathodes and anodes were evaluated and compared with conventional Nafion ionomer GDEs using Nafion 112 as the PEM under elevated temperature and reduced relative humidity. ZrP-modified Nafion ionomer was incorporated into the catalyst layer to enhance water retention and/or increase the protonic conductivity. The fabrication of ZrP-GDEs was implemented by the ion exchange of Nafion solution with zirconyl chloride, followed by the impregnation of GDEs in H3PO4 solution. The composite electrolytes in the catalyst layer possessed a ZrP content of 20% by weight. GDEs were characterized by TGA, SEM, XRD, and CV. Scanning electron microscopy (SEM) indicated evenly distributed elemental Zr and P within the catalyst layer. Cyclic voltammetry shows a reduced electrochemically-active surface area when the ZrP is incorporated into GDEs. Polarization and impedance analyses indicate the cathode with ZrP-modified Nafion ionomer did not show an enhanced or decreased performance, compared with conventional Nafion ionomer GDEs under elevated temperature and decreased humidity. However, when GDEs with ZrP¬Nafion ionomer were used as the anode, an improved performance was observed. Preliminary experiments show that the anode is more sensitive to dehydration than the cathode under elevated temperature and/or low humidity. Improving the anode water retention capability will help to reduce losses at the anode. However, the incorporation of hygroscopic agents in the cathode catalyst layer is not essential because it is self-humidified by electrochemically-produced water even under elevated operating temperature and lower humidity.

Jan 1, 2005

By Andrukaitis. E.

The increasing use of electronic equipment by the Canadian Forces has increased the importance of electric power. A power source that is packed with energy and yet light, small and durable is the common request of military users. However, this needs to be achieved while also addressing the requirements of safety, reliability and low temperature performance. The potential use of fuel cells in a military environment has become a possibility in several areas in the 21st century. Some examples of power source requirements and the materials related R&D required to give better, higher energy power systems in the future will be discussed.

Jan 1, 2005