Search Documents

By M. Mahfoud

The effect of grain refinement on the tensile and fatigue crack propagation behavior of sand cast magnesium alloy AM60B has been investigated in the present study, C2Cl6 in the amount of 0,3% was used to grain refine the melt, The fracture toughness tests were conducted in laboratory air at room temperature (25°C) using a sine-wave cyclic frequency of 20Hz and a load ratio of R = 0,1, The response in the Paris's regime and the critical stress range were determined, Preliminary findings have shown that C2Cl6 has a significant effect on both the tensile properties and fatigue crack propagation of the alloy tested, Grain refinement increased both the yield and ultimate tensile strength by more than 46%, and decreased the crack growth rate from 2,7 to 1,4 MPa Vm , However, the grain size seems to have a smaller effect on threshold stress intensity factor range. The fracture surfaces of specimens were examined optically and under the scanning electron microscope (SEM) to determine the relationship between grain size and fatigue properties.

Jan 1, 2005

By Christoph Broeckmann, Andrew Gardula

"The adoption of high-pressure grinding throughout the cement industry has yielded enormous savings in energy and wear material costs. There are also a number of installations, which are applied in iron ore and kimberlite processing operations. High pressure grinding offers the same potential for energy and media savings, as well as opportunities for improved, downstream metallurgical performance, in hard rock mineral processing. This paper focuses on developments in machine design and wear surface engineering for high-pressure grinding of the hard rock ores in the mineral processing industry.INTRODUCTIONIn the early eighties 3.4 % of the world electric energy was consumed for crushing and grinding operations of minerals and 0.6 % in the ore dressing industry. During that time using a laboratory press Prof. Schönert found that interparticle comminution at high pressure requires remarkably less energy as conventional grinding technologies. In grinding of cement clinker he expected energy savings between 33 and 50 % compared to ball mills [1]. Piston presses are limited in throughput. Thus, the principle of interparticle comminution was adapted by the use of high pressure grinding rolls (HPGR) to a continuous plant process. Figure 1 shows the main components of a roller press: The roller nip of width s is formed between the floating roller (1) and the fixed roller (2). The diameter of the rolls will be denoted with D, the width with B. The total press force F can be adjusted using a hydraulic system with two or four pistons (3). In order to compare machines with different roll geometries the specific pressing force p is introduced:"

Jan 1, 2005

By Gregg S. Hill, Bert J. Huls

"This paper on coarse particle recovery (CPR) summarizes a process to capture coarse particles that are not recoverable by regular flotation. Several porphyry copper operations in the world operate analogous circuits that recover non-floated copper from tailings; however, the case presented here is unique in that extensive underlying test work has allowed us to elucidate some fundamental principles behind recovery enhancement. This paper discusses an overview of the flow sheet that is proposed to Minera Escondida Ltda., the nature of copper in the feed to the CPR circuit, and the various unit operations within the recovery circuit. Details of the technology behind each unit operation will be presented in later publications.INTRODUCTIONSince 1996 BHPBilliton and MEL (Minera Escondida Ltda.) have developed a process to recover copper from coarse particles in the rougher tailings. Copper recovery from fresh tailings is not new. Several operations in Chile, such as Chuquicamata, El Teniente (AMEC, 2003), Mantos Blancos and others have operated various forms of tailings circuits. Both Chuquicamata and El Teniente practice cascade flotation scalping off froth containing fine copper particles after allowing sufficient retention time, air inducement and, sometimes, additional reagent addition. Chuquicamata tailings are not segregated but floated in sequential cascade and conventional large cell arrangements. At the Valle Central operation of El Teniente a coarse fraction of mill tailings is ground and floated, with the rejects recombined with fine tailings and subjected to cascade flotation through a sequence of concrete launders as the tailings flow towards their final deposition area. Mantos Blancos cyclone the rougher tailings and blend the underflow with scavenger concentrate from elsewhere in the principal circuit prior to flotation in Wemco Cells. Kemess in BC, Canada operates a 160 m3 Outokumpu cell to reduce the tailings sulfur content (Rasmussen, et.al, 2004)."

Jan 1, 2005

By R. T. Jones

The largest known platinum group metal (PGM) deposit in the world is the Bushveld Complex in South Africa, with the Great Dyke in Zimbabwe also being one of the biggest. It is therefore not surprising that the majority (just over 5 million troy ounces or 156 metric tons per annum) of the world's platinum is produced in Southern Africa. Primary smelting of ore concentrates is carried out in that region by five companies, namely Anglo Platinum, Impala Platinum, Lonmin Platinum, Northam Platinum, all of South Africa, and Makwiro Platinum in Zimbabwe. The only other primary smelter of platinum group metals is Stillwater Mining of Montana, USA, although very significant quantities of PGMs are produced as co-products by Norilsk Nickel of Russia. Smaller (but still significant) quantities of PGMs are produced by Falconbridge and Inco of Canada, also as co-products from nickel sulphide smelting. There are many similarities between PGM smelting and nickel sulphide smelting, and the range of technologies in use includes six-in-line rectangular electric furnaces, three-electrode circular AC furnaces, Peirce-Smith converters, and Anglo's ACP (based on Ausmelt technology). PGMs are also recovered from residue materials using DC arc furnace technology.

Jan 1, 2005

By C. I. Garcia, G. Zhou, W. Gao, A. J. DeArdo

The development of X-100 and X-120 linepipe steels was investigated using a series of low-carbon Mo-Nb-B steels. The laboratory steels were vacuum melted and processed using advanced thermomechanical processing (TMP) philosophies. Prior to the laboratory hot-rolling experiments, the grain coarsening temperature, the conventional T95 and T5 start-stop recrystallization temperatures and the transformation behavior of y were studied using a computer-controlled high temperature deformation MTS-458 and a Theta-IV High Speed dilatometer systems. The results from these experiments provided the guidelines for the design of the laboratory hot-rolling TMP processing experiments. The mechanical properties of the experimental steels showed yield strengths in the range 700-850 MPa and CVN impact properties of over 80 J at -20°C. The best balance of mechanical properties was obtained by using CCR+DQ+Tempering treatments. The major microstructural features responsible for the observed mechanical properties in order of importance were: a) substructural refinement associated with lower bainite, b) dislocation strengthening, c) fine recrystallized ferrite, and d) small amounts of retained austenite. Fine Nb(C,N) precipitates formed in ferrite were observed, however their contribution to the strength was minimum. Most of the Nb(C,N) precipitation took place in austenite. This precipitation was used to exert microstructural control of austenite during hot rolling. The physical metallurgy and optimum TMP to achieve the mechanical properties are detailed in this paper.

Jan 1, 2005

By J. Bakos

Solar Hydrogen Energy Corporation (SHEC Labs) recently constructed a pilot-plant to demonstrate a Dry Fuel Hydrogen Generation System that is powered primarily by sunlight focusing-mirrors. The pilot-plant consists of: A Solar Mirror Array and Advanced Solar Concentrator and Shutter System; and two thermo-catalytic reactors to convert Methane, Carbon Dioxide, and Water into Hydrogen. Results from the pilot study show that Solar Hydrogen generation is feasible and cost-competitive with traditional Hydrogen production. More than 95% of Hydrogen commercially produced today is by the Steam Methane Reformation (SMR) of natural gas, a process that liberates Carbon Dioxide to the atmosphere. The SMR process provides a net energy loss of 30 to 35% when converting from Methane to Hydrogen. Solar Hydrogen production provides a 14% net energy gain when converting Methane into Hydrogen since the energy used to drive the process is from the sun. The environmental benefits of generating Hydrogen using renewable energy include significant greenhouse gas and criteria air contaminant reductions.

Jan 1, 2005

Stellite-6 coatings were formulated on two Ni-base superalloys, namely Superni 75 and Superni 600, by a shrouded plasma-spray process, and the oxidation behaviour of these coatings has been investigated in air and in an aggressive environment of Na2SO4- 60%V2O5. Accelerated oxidation tests were conducted in a silicon-carbide tube furnace under cyclic conditions at an elevated temperature of 900°C for 50 cycles. Each cycle consisted of 1 h heating and 20 min cooling in air. A thermogravimetric technique was used to approximate the oxidation kinetics. The corrosion scales were characterised by XRD, SEM/EDAX and EPMA analysis. It has been observed that the coatings nearly followed the parabolic rate law of oxidation. Overall weight gain conceived in air was just 51% of that in the aggressive environment in the case of coated Superni 75, whereas in case of coated Superni 600, the cumulative weight gain in air was found to be one-third of that in the Na2SO4-60% V2O5 atmosphere. Furthermore, the coating showed very good adherence to both of the substrates during the course of air oxidation, whereas some superficial cracks were observed near the edges of the specimens during the molten salt induced oxidation. XRD analysis revealed the presence of phase-like CoO, CoCr2O4 and Cr2O3 in the oxide scales, which are reported be protective against high-temperature oxidation. The XRD results were further supported by SEM/EDAX and EPMA.

Jan 1, 2005

By Chris Larsen, Carole Fortin, Dave Scott, Curtis Deredin, Ian Orford, Jean Guy Gauthier, Andy Trusiak, Lyne Côté, Mike Cooper

"Upon successful commissioning of the Stage Grinding Project (Cormier et. al., 2002), process improvements predicted through pilot plant testing were obtained in several flotation circuits, resulting in higher grades and recoveries for zinc and lead concentrates. Subsequent to establishing new baseline operating conditions from the Stage Grind Project implementation, additional opportunities were identified, and through the application of Six Sigma methodologies further gains were made. Six Sigma improvement projects were carried out in the copper-lead, zinc, lead upgrading and bulk flotation circuits. The overall performance increase resulting from incremental improvement projects has been substantial.Most remarkably, given the operational maturity up to the late 1980’s, the Brunswick concentrator team has continued to deliver a steady stream of major improvements over the past fifteen years. While senior managers and their programs have changed several times, there have been some critical constants over the long run. Common elements have been a commitment to team work, a commitment to recruit and maintain technical personnel, a structured business improvement framework supported organizationally by senior management, and focus on a few priority initiatives rather than trying to fix everything at once.The paper briefly discusses the longer term setting and then endeavors to illustrate, with examples, how improvements are presently achieved by applying the Six Sigma quality program.INTRODUCTIONThe Noranda Inc. Brunswick Mine, located near Bathurst, New Brunswick, is one of the world’s larger lead/zinc mines. Milling of ore began in 1964 from the No. 12 orebody, with an expansion in 1966 to accommodate ore from the No. 6 mine. In excess of 100 million tonnes have been milled to date. The concentrator employs differential flotation to produce lead, zinc, copper, and lead/zinc bulk concentrates. The ore is massive sulphide, with approximately 20% valuable minerals, 60% pyrite and 20% silicates."

Jan 1, 2005

By D. Berkley

Off-gas systems often become the limiting factor in production increase and environmental projects. Any upgrade or new off-gas project needs to address control instability issues, instabilities that can result in safety hazards, significant loss of system capacity and/or emissions to the environment [1]. In addition, the design engineer must optimize system configuration and equipment size for the new operating conditions, to have a technically feasible and economically viable project. Dynamic simulations can be used for addressing both the control stability and the design optimization issues. This paper illustrates how the dynamic simulation of transient processes and of their control system can be used in "real life" situations for these purposes, presenting the example of an electric furnace off-gas system design.

Jan 1, 2005

By M. Drozd, A. Ibrado, P. Butcher

While effective in treating refractory sulfide ores, pressure oxidation leaves carbonaceous matter unscathed and able to adsorb gold from cyanide solutions. Barrick Goldstrike's strategy to mitigate this problem is to minimize contact between dissolved gold and native carbon in advance of the carbon-in-leach (CIL) process. Measures currently in use include limiting carbonaceous matter in the plant feed by meticulous blending of ore, controlling the degree of oxidation in the autoclaves and blinding native carbon surfaces with lauryl sulfate. The presence of residual cyanide and thiocyanate in the process water remains to be a cause of premature gold dissolution and loss of gold by adsorption on carbonaceous matter. This cyanide is introduced by water that is recycled from the tailing pond. Of several treatment options considered, oxidation by peroxymonosulfuric acid, also known as Caro's acid, is deemed to be the most effective. Laboratory and pilot plant tests show that Caro's acid can oxidize free cyanide, weak¬acid-dissociable (WAD) cyanide and thiocyanate, resulting in significant improvements in gold recovery downstream. The process requires Caro's acid at 125 % of the stoichiometric requirement and pH in the range of 9.5 to 10 to accomplish the desired destruction in about twenty minutes. A cyanide destruction plant is currently being designed and construction should be completed by the end of 2005.

Jan 1, 2005

By D. Mu

A method is presented for evaluating the effective gas diffusion coefficient of porous media. A series of random-distributed porous solids with different porosity are generated, a solution of the gas diffusion equations inside the porous media is obtained using the finite element method (FEM), and then the effective gas diffusivities are computed. The results show that there is a percolation threshold sp, and this percolation threshold decreases with an increase in the connectivity of the pore network; the relationship between the effective diffusivity and the porosity is strongly nonlinear when the porosity £ is less than about 0.2; and is quasi linear for higher porosities. The threshold decreases with increasing the connectivity of the pore network. A formula relating the effective diffusion coefficient with porosity is proposed.

Jan 1, 2005

By G. Roy

Interest in metal-hydrogen systems can be manifold. Small amounts of hydrogen adsorbed by elemental metals and alloys usually result in strong changes in the physical and mechanical properties of engineering materials. Overwhelmingly, these changes, viz. hydrogen embrittlement, are considered deleterious with respect to structural performance of engineering materials. However, the changes, often studied by metallurgists and metal physicists, can present new possibilities and applications. A prominent example is the recent interest in safe, solid-state hydrogen storage in metallic lattices. In a new laboratory in MTL, Ottawa, a study has been initiated to investigate the effect of "micro- and macro- alloying" of Al and Mg powders with hydrogen (in high-energy mechanical alloying mills) on plastic deformation in metal and metal hydride structures. It is anticipated that high-rate impacting and subsequent grain refinement in the mill will have an effect on hydrogen storage capacity in lightweight magnesium and aluminum alloys. First examination of the state-of-stress by X-ray diffraction in high-rate milled, nanostructured pure aluminum, aluminum milled with a solid surfactant, and aluminum or magnesium alloy milled with hydride and/or gas hydrogen will be presented.

Jan 1, 2005

By F. Barriga-Ordonez, J. A. Finch, L. Calzado, S. R. (Ram) Rao

Sludge, formed by lime treatment of acidic drainage and stored in tailing ponds of the Sudbury region, contains 5-7% Ni, mostly in a mix of hydroxides with Fe (~ 10%), Mg (~ 10%) and Cu (-0.5%), and Ca (-3.5%) as sulphate. Investigations were conducted to recover nickel by a 2-stage process. In the first stage, the sludge was leached with sulphuric acid at pH 3.2. About 90% of the nickel was extracted, producing a solution, which contained mainly nickel (2 g/L) and magnesium (3.7 g/L). In the second stage, nickel was separated by treating with ozone which recovered 99% of the nickel in the Ni(III) oxidation state as -85% pure nickel oxide-hydroxide (NiOOH) precipitate. The oxide settled and filtered readily. A potential use of the product in battery making is suggested. The leach residue contained 0.5% Ni making it less toxic for disposal. Some physical properties of nickel oxy-hydroxide and process parameters including ozone consumption will be discussed.

Jan 1, 2005

Ni and samaria-doped ceria (Ni-SDC) cermet are desirable materials for making a solid oxide fuel cell anode working at intermediate temperature (800°C or lower) due to its good ionic/electronic conductivity at the reduced operating temperature. An advantage of the use of a Ni-SDC anode is the enlargement of the effective reaction zone in the interfacial area between the anode and the electrolyte. As a result of the mixed ionic/electronic conductivity of the anode, the electrode reaction rate is enhanced. Investigations into the properties of the ceria-based anode reveal that the performance of the anode is closely related to its microstructures, which are dependent on the composition and fabrication conditions of the ceramics. In this paper, a method for quantitative characterization and correlation of Ni-SDC cermet microstructures to the performance of an anode is investigated. A series of Ni-SDC anode samples are prepared by screen-printing (SP) and spin-coating (SC) techniques, and different microstructures of the samples are obtained through controlling the SP or SC conditions and the sintering temperature. Individual phases (Ni, SDC and pore) in the tri-phase boundary (TPB) microstructures in the electrode are differentiated and segmented from each other in optical and SEM images based on the differences in refractivity and atomic contrasts among the phases. The geometric properties of the segmented phases are characterized using image analysis methods, so that a quantitative skeleton illustrating the TPB microstructures of the Ni-SDC electrode is obtained. Statistical analysis of the distribution of the three phases in the TPB microstructures is performed and the relationship of the microstructures with the optimum electrode is interpreted in terms of the microstructure analysis data.

Jan 1, 2005

By G. P. Gu

The in-service 90/10 cupro-nickel tubes in a water-chiller system suffered from severe corrosion damage during their relatively short service life causing unexpected down time. In addition to downtime, the environmental risk associated with losing refrigerant was also a concern that initiated this investigation, Microstructural investigation using SEM and electron microprobe indicated that pitting corrosion had resulted in local nickel depletion, During the corrosion process, copper appeared to have re-deposited around the corrosion pits accelerating the local corrosion.

Jan 1, 2005

By C. O. Aksoy

There is a long history of coal production in Turkey with electric energy generated from power plants since the 1950s. However, the cost of power generation is high. Therefore, it has become necessary to find a means of decreasing production costs to become more competitive in a global market. This paper attempts to economically minimize the overall operating costs of a dragline-shovel-truck system applied at an open pit mine that has fed the Yatagan power plant since 1979, lowering the lignite production cost, and indirectly, the overall electricity generation unit cost. Systems currently in place, as a result of former optimization studies, are time-consuming and expensive to re-implement to comply with today’s very different geometric and economic conditions affecting mining operations. In such cases, rather than re-optimization, it is more viable to identify the parameters that affect the minimum unit cost, via a cost minimization study, allowing present mine equipment to be utilized more efficiently. Unit cost minimization analyses are subject to the capacity of the pool of mining equipment available, combined with the mining block geometry from pre-stripping onwards. In this overall unit cost minimization study, P&H shovels and CAT 777 trucks with capacities of 15 yd3 and 77 tons, respectively, were used in truck-shovel pre-stripping operations. A 65 yd3 Marion 8050 dragline was used to expose the overburden immediately over the coal seam. Pre-stripping bench heights varied from 8 m to 20 m and dragline bench heights from 20 m and 25 m were evaluated to minimize the unit cost of field operations. Total overburden extended to a depth of 60 m (35 m to 40 m for pre-stripping). Minimization analyses performed on the pre-stripping truck-shovel operation, prior to dragline operations, determined that the shovel bench height should be 15 m requiring a dragline bench height of 25 m.

Jan 1, 2005

By A. Chaisantikulwat

Most solid-oxide fuel cell (SOFC) modeling emphasizes steady state cell operation. However, understanding the dynamic behavior is essential to predict the performance and limitations of SOFC power systems. In this work, we demonstrate a dynamic model of a SOFC, and we simulate a feedback control scheme that can maintain output voltage despite load changes. Dynamic response is determined as the solution of coupled partial differential equations derived from conservation laws for energy, mass and electric charge. From such a model, the step responses to system input variables can be determined. Low order dynamic models that are sufficient for feedback control design can be derived from the step responses. The development of the partial differential equation model is outlined, and the limitations of the control system are discussed.

Jan 1, 2005

Commercial SOFC systems will likely utilize hydrocarbons or hydrogen produced from hydrocarbon fuels and therefore will likely be exposed to sulfur impurities. Conducting-Atomic Force Microscopy (C-AFM) is a scanning probe microscopy technique which maps both sample topography and conductivity with tens of nanometers resolution. In Ni-YSZ, C-AFM measures the resistance of the metallic network at scanned locations, with the ability to differentiate between interconnected and isolated metallic particles. We have applied C-AFM to Ni-YSZ SOFC anode materials, with the goal of monitoring changes in the conductivity of the Ni anode network resulting from SOFC degradation processes, such as H2S poisoning.

Jan 1, 2005

By E. Dernedde

Industrial plants located in the province of Quebec, Canada, are subjected to large variations of the ambient air temperature, Building ventilation systems of these plants must have some flexibility in order to meet industrial hygiene standards (TLV for chemical substances, heat stress and cold stress) at any time of the year, The building ventilation of a bath treatment plant of an aluminium smelter in Quebec was examined under summer and winter conditions, Part of the plant has periodic emissions of hydrogen fluoride gas and heat from hot anode butts, CFD modeling was used to optimise the building ventilation of the bath treatment plant, The present study proposes a modified building ventilation system, which improves the internal environment, complies with industrial hygiene standards and also reduces heating costs by 20 % during winter.

Jan 1, 2005

By L. Sun

A numerical model has been developed to study the air flow in the flow plate and gas diffusion layer assembly on the cathode side of a PEM fuel cell. The flow plate in this type of fuel cell often has serpentine channels and the porous layer is adjacent to the flow plate to diffuse the air to the catalyst layer. Flow cross-over of air through the porous diffusion layer from one part of the channel to another can occur. This flow cross¬over is a result of the pressure differences between different parts of the channel, and it causes the flow rate through the channel to vary with the distance along the channel. A numerical study of pressure distribution and flow cross-over through the gas diffusion layer (GDL) in PEMFC flow field using a serpentine channel system has therefore been undertaken to compare the cases of a single channel and two parallel channels, with the channels having a trapezoidal cross-sectional shape. The purpose of the present work was to study the effect of the flow plate geometry on the basic fluid flow through the plate. The flow here has been assumed to be three-dimensional, steady, incompressible, isothermal and single-phase. The flow through the porous diffusion layer has been described using the Darcy model. The dimensionless governing equations have been solved by using the commercial CFD solver, FIDAP. From the results obtained, it can be found that the single channel systems have greater maximum flow rate difference than the parallel channel systems under the conditions considered in the present study. Also, the size ratio R of trapezoidal cross-sectional shape has a significant effect on the flow cross-over and pressure variation in the flow field.

Jan 1, 2005