Search Documents

By M. Gruber-Pretzler

Technical Sn- bronzes tend to form both macrosegregations and microsegrega¬tions during DC-casting due to the particular thermodynamic properties and kinetics of phase transformation. As a result a heterogeneous cast microstructure forms that is some¬times a reason for a decrease in workability. The extent of macrosegregations in DC-casting can effectively be influenced by casting parameters like casting velocity, primary cooling or inlet geometry which in fact change the relative flow between the melt and the forming solid. In order to understand the influence and interaction of the related phenom¬ena, simulation methods are applied. The solidification of the strand as well as the forma¬tion of macrosegregation are simulated with a two phase volume averaging model. The velocity field of the melt flow is explicitly calculated by solving the corresponding mo¬mentum conservation equations. Within the mushy zone the local formation of microseg¬regations in the presence of feeding flow is estimated. The thermodynamics of the Cu-Sn system is accounted for and it is distinguished explicitly between interface and average concentrations. To investigate the influence of feeding flow on the formation of mac-rosegregations, a study has been performed. Based on this result, the phenomena of mac¬rosegregations are described in a detailed discussion.

Jan 1, 2007

By A. Haldar

This study focuses on the flow characteristics of hypereutectic Al-Si alloys in thin sections. The pattern assembly consisted of spiral horizontal patterns, 6.25 mm (0.25 inch) and 12.50 mm (0.50 inch) in thickness with a common sprue. Al-Si alloys with silicon levels of 14%, 18% and 22% were poured with superheats of 60°C, 115°C and 170°C. It was observed that metal fluidity (in terms of flow length and metal velocity) increased with increase in silicon levels and superheat for both section thicknesses. It was also observed that, for a section thickness of 6.25 mm (0.25 inch), silicon level had more pronounced effect on the metal fluidity. For 12.50 mm (0.50 inch) thickness, both silicon level and superheat affected the metal fluidity. The surface hardness of the castings increased with an increase in silicon level of the alloys at the gate and the flow tip. Detailed study of the flow tip was also carried out with a view to understanding the effect of silicon level and superheat on undulated flow length, surface hardness and microstructure.

Jan 1, 2007

By J. Contreras

In the period 2003-2004, the situation of the copper concentrate market was unfavourable for smelters and refineries, with low TC/RC values and euro-dollar parity affecting European companies negatively. Within this scenario, Atlantic Copper decided to develop a plan to increase its competitiveness and to improve its results in these market circumstances. The plan affected all departments in the Company and was based mainly on cost reduction in energy and manpower. A general analysis of the Complex's overall efficiency was carried out and, based on this analysis, two major Projects emerged, "Primavera" and "KF". Each Project consisted of smaller sub-projects which aimed at improving the areas which could perform better according to our general analysis. The paper describes how this entire project developed and the final results obtained by the Company.

Jan 1, 2007

By D. M. Aloi

In today's evolving and globalized world, mining companies are being pressured to move beyond compliance towards long-term sustainability and sustainable development. Companies are expected to "engage" with communities and measure the success of these engagements without a clear understanding of "how" to do this. This move, away from "Corporate" Social Responsibility (CSR) and compliance, develops more of a focus on "Community" Social Responsibility and sustainability. This shift in focus leads to the development of world-class projects that provide sustainable development for people, reduces the incidence of costly delays, and promotes good global citizenship for corporations. The process of "engaging" communities in mining project design and development leads to a stronger license to operate and sustainable development. To create this mutually beneficial relationship between communities and companies, communities must be "engaged" in the mining process as early as possible, preferably during the exploration or the concept phases. How to create this "engagement" remains elusive. How to measure the progress of this engagement is also problematic. The quantitative and qualitative metrics needed to measure both positive and negative impacts of the mining and community relationship will be discussed.

Jan 1, 2007

By V. Ramachandran

The successful advent of solvent extraction (SX) reagents for copper recovery and improvements in electrowinning of copper to produce LME grade A copper cathode have paved the way for the hydrometallurgical treatment of copper oxide and low grade sulfide ores. This has resulted in about 25-30% of the world's copper being produced today by the Leach-SX-EW process. The obvious next step was to develop processes for the hydrometallurgical treatment of copper sulfide concentrates, as an alternative to a typical smelter-refinery complex. The current paper updates the processes that have been developed to date with emphasis on processes that are being commercialized or that are seriously under consideration for commercialization. Most of the discussions relate to the hydrometallurgy of chalcopyrite concentrates, which account for about 70% of the world's known copper reserves. In summary, in the last thirty years, the hydrometallurgical treatment of copper sulfide concentrates has attained full maturity and will be a serious option to contend with while evaluating any future new copper plant.

Jan 1, 2007

By O. C. Rojas, J. Sanhueza, J. C. Vargas

Empresa Nacional de Minería (ENAMI) is dedicated to the promotion of small and mid scale Chilean mining industry. Paipote, ENAMI Copper Smelter, processes a variety of mineral products as the result of this promotion. The mineral products characterize a wide variation of copper, iron, sulfur and precious metals content as well as the significant dispersion in the content of impurities, such as arsenic, antimony and bismuth. The Smelter Modernization Program, initiated in1997, introduced a series of technological and operational changes. The development of operational planning and control strategies was necessary to optimize the blending of a wide variety of concentrates and the control of metallurgical processes in order to ensure the stable operation, fulfillment of environmental regulations and the quality of produced copper anodes. A permanent optimization process carried out in the last decade led to the permanent increase of the smelting capacity and the production of anodes and sulfuric acid. Additionally, introduced improvements affected the smelter efficiency and metallurgical recovery, demonstrating the possibilities of the optimization of a small smelting facility reflected in good metallurgical and economic results. This paper presents the smelter evolution, introduced technological and process control changes as well as incorporated new reactors and equipment as a continuous process of optimization.

Jan 1, 2007

By M. R. Coffin

In recent years, improved operation of the Kidd smelter has resulted in an increase in blister production capacity. Due to manpower and equipment limitations anode production and treatment rates could not be increased without incurring significant additional operating expenses. The option chosen to expand casting and refinery capacity to meet the available blister supply was to increase the anode thickness while maintaining the same anode exchange cycle in the refinery. This has resulted in a cathode production increase of almost 10% for minimal expenditure. Equipment and process modifications required to cast and refine the thicker anodes are discussed in this paper, along with the Six Sigma methodologies used to identify them. Key areas covered are Hazelett continuous caster operation, refining process parameters, plating performance and cathode quality.

Jan 1, 2007

By K. Yoo

Chalcopyrite is the most abundant copper sulfide mineral, which is normally processed using pyrometallurgical methods (i.e., smelting) to produce copper metal. Smelting has several major disadvantages, such as high gas-handling costs, high capital costs, saturation of sulfuric acid market, and inability to treat low-grade concentrates and to recover some by-products, such as zinc, nickel and cobalt. The development of hydrometallurgical processes for chalcopyrite is desirable to overcome the problems of smelting. Because chalcopyrite is refractory, the leaching rate for chalcopyrite is very low. Therefore, increasing the leaching rate has been extensively investigated, both in sulfate and chloride media, as well as in the presence of bacteria. Chloride leaching processes have shown relatively high leaching rates. The mechanism of the chloride leaching process has been investigated, but the behavior of chalcopyrite leaching in chloride solution is not clear. Therefore, the effect of the solution redox potential on the leaching rate of chalcopyrite in chloride solution was investigated. In the present study, leaching experiments were carried out using 0.1 M chloride solutions and the results indicate that high leaching rates of chalcopyrite can be achieved at relatively low solution redox potentials.

Jan 1, 2007

By D. Allen

Faced with decreasing ore grades and harder ores, many mines today are forced to become more efficient with their approach to processing. Variability in ore hardness, mineral liberation, reagent consumption, sliming, and leach responses are all a function of the minerals present and their concentration. Modern semi-automated X-ray Diffraction (XRD) analyses using Rietveld refinement techniques, in conjunction with high speed quantitative Near Infrared (NIR) analyses, provide reliable quantitative mineralogical ore profiling. By the implementation of XRD with NIR, mining, milling and leaching operations no longer need to be dependant on visual estimates for GeoMetallurgical Modeling and are provided with a valuable forecasting and production control tool. This paper will illustrate the development, plant implementation and application of XRD and NIR at several copper operations.

Jan 1, 2007

By Dave Bulled

"This paper describes the design of a molybdenite flotation circuit using FLEET technology applied to kinetics data produced from laboratory flotation testing and distributed across the blocks of a mine plan using a geostatistical approach. The geostatistics assigned the statistical error that arises from having a limited amount of sample testing data to the kinetics estimates of each block of ore in the mine plan. The final design then included a quantification of risk based on the accuracy of the block flotation kinetics and model fitting. The design made reference to the extensive technical reports describing earlier metallurgical test work including some pilot plant work over thirty years ago.The testing involved conducting MinnovEX Flotation Tests (MFT) to determine the rougher flotation kinetics at the specified reagent conditions and rougher-cleaner tests to determine the change in kinetics resulting from regrind. These flotation kinetics were used within FLEET simulations to create a full-scale flowsheet and plant design including recommended equipment sizes and the forecast of operating results. Measurement of detailed flotation kinetics for a wide range of samples allowed the effect of size of grind and efficiency of classification (i.e. width of size distribution) to be predicted for the whole ore body.INTRODUCTIONAdanac Moly Corp. proposed to develop a 20,000 ton per day mill to produce high quality molybdenite concentrate from its Ruby Creek resource in north-western British Columbia. It is a relatively clean low grade porphyry-monzonite occurrence containing minimal quantities of other sulphides such as chalcopyrite, pyrite, sphalerite and galena. Molybdenite occurs mainly as coarse flakes with lesser amounts of finer sized values. An optimum plant design was required to can achieve the predicted operating results, at a known level of risk, while treating the variability inherent in the ore body."

Jan 1, 2007

By K. Koyama

As a study to establish a new energy-saving copper recycling process, the copper deposition at a cathode and oxidation of copper(I) at an anode from ammoniacal alkaline solutions containing Cu(I) or Cu(II) were investigated in order to examine the feasibility of electrolysis in this solution.. The current efficiencies were greater than 95% in the current density range of 200 to 1000 A m-2. The current efficiency decreased with the increasing Cu(II) concentration and temperature. In the batch-type electrolysis at the anode, during the initial stage, the current efficiencies were 100%, and the anode potentials ranged from 0 to 0.15V vs. SHE at a current density of 100 A m-2. During the subsequent stage, the current efficiency decreased with time, and the anode potential was around 1.35V vs. SHE where oxygen evolution at the anode surface was observed. As a result, the present electrolytic method can be the core technology in the said copper recycling process.

Jan 1, 2007

By G. V. Fernandez

Sociedad Minera Cerro Verde S.A.A leaches secondary copper sulfides. In recent years, the mine has introduced innovations that have improved the management of mineral crushing, agglomeration, curing, and leaching. The crushing plant, for example, uses the concepts of degree of balance and percentage of time in an operationally balanced state which, displayed in real time, facilitate more intensive and uniform utilization of the crushers. High agglomerate quality is ensured with the correct dose of moisture, which is adjusted to the changing characteristics of the mineral through the use of electrical conductivity measurements. The amount of acid used for curing the agglomerate is also adjusted by using quality control information. Finally, the stockpile irrigation regime is managed using the criteria established by the "Lixiviant Request Rate", which optimizes the addition of leaching solution, creating such benefits as faster recovery, and reduced acid and energy consumption.

Jan 1, 2007

By H. P{ops

This paper summarizes important developments that have occurred in the mining and subsequent production of copper into rod and wire from 9000 B.C. until the present time. Principles and practices associated with continuous rod production are discussed from a metallurgical perspective, and include the effects of oxygen content and impurities. A brief historical review is also given of important wire drawing events dating back thousands of years. Finally, predictions concerning the future of the wire and cable industry are presented with particular emphasis upon copper wire, technology in this market, and competitive materials.

Jan 1, 2007

By S. R. Izatt

The use of MRT, a highly selective separations technology, has long been demonstrated to be a cost effective, efficient, and environmentally sound process for extraction of a wide range of anions and cations that are commonly found in copper electro - refining and electro - winning circuits, as well as in environmental treatment operations. This paper provides an update of commercial MRT applications in the copper industry. Several recent installations and test programs are reviewed including recovery of bismuth from tank house electrolyte, and from chloride matrix selenium reduction solution which is generated in the anode slimes treatment process. Recovery and refining of platinum group metals originating in the anode slimes is also discussed. Various other base metal and other target separations of interest to the copper producer are also reviewed. The recovery products are high purity metal salts which can be marketed directly or readily reduced to metal.

Jan 1, 2007

By G. Plascencia, C. López, J. González, D. Jaramillo, M. A. Barrón

Air jet and molten matte interaction within a Peirce - Smith converter is analyzed during the first stages of blowing using Computational Fluid Dynamics (CFD), by means of the Large Eddy Simulation and Reynolds Stress turbulence models. Jet velocities ranging from 5 to 150 mis, which involve the bubbling and open jet regimes, were considered in 2 and in 3-D numerical simulations. As a result of the computer simulations, it was found that low velocities results in gas bubbling in the molten copper, whereas higher gas velocities results in well defined plumes. The consequence of such different behaviours results in an increment in the rate of refractory wear or in copper splashing respectively. The analysis of the results may lead to improve the design of the tuyeres currently used in copper converting. Bottom blowing of air is also explored in this work. Numerical results show a strong non-linear parabolic behaviour of the jet velocity on the average velocity of copper; which means that beyond certain jet velocity, the copper de-accelerates thus reducing its velocity. This may be due to the open nature of the jet, which prevents the momentum transfer from the injected gas to the molten copper.

Jan 1, 2007

In the flotation of a copper ore, entrainment of fine silicate and iron sulfide gangue minerals resulted in poor copper concentrate grade. In the cleaning stage, rejection of these gangue minerals was particularly difficult due to severe mechanical entrainment when the rougher concentrate was ground to 10 µm. To reduce gangue entrainment, polymeric depressants were tested. The rationale being that with the use of such polymeric depressants that also possess flocculation power, not only minerals-to-be-depressed can be made hydrophilic, but their particle size can also be enlarged. In this manner both the "genuine" flotation and the mechanical entrainment can be reduced. An effective polymer to reduce entrainment of silicate gangue mineral in sulfide flotation was identified from bench flotation tests conducted on single minerals. It was then applied to the flotation of a copper-gold ore confirming the beneficial role of the polymeric depressant in the reduction of fine gangue entrainment.

Jan 1, 2007

By K. Krishnapisharody, S. Clark, M. Barati

Different gas purging methods to metallurgical baths have been applied to date, among which are top lancing and bottom blowing through tuyeres or porous plugs. Among these, the porous plug bottom blowing technique has shown higher efficiency in gas utilization than tuyeres and top blowing, due to smaller bubble size and lower liquid velocity. However, the studies related to bottom stirring of metallurgical baths are limited to slag-less or thin slag-covered melts. In particular, there is no examination of stirring ability in conditions similar to Falconbridge's Slag Make Converter, where the bath is covered with a thick slag layer and a stream of solids is charged on the bath from top. This study was undertaken to investigate the application of gas purging through a porous plug in stirring in and melting of the solid feeds. The spreading behaviour and melting time of a solid layer forming on a plume created by stirring were calculated using the existing models. The results show that formation of a thick solid layer, specifically in areas beyond the plume region is very likely. Nevertheless, the thickness of the layer and melting time do not appear unreasonably high. It is predicted that by proper controlling of gas flowrate and plug configurations, successful solid charging through the mouth can be practiced.

Jan 1, 2007

By K. C. Sole

In most copper solvent-extraction operations, an important consideration in choice of extractant is the requirement for high selectivity of copper over iron. Ester-modified aldoxime extractants presently offer the best Cu:Fe selectivity. In some plants, however, the process feed liquors contain significant amounts of manganese but little iron. Although manganese is not chemically extracted by oximes, trace amounts are carried over to the electrowinning circuit by physical entrainment. This may result in anodic oxidation of manganese which, in turn, can cause oxidative degradation of the organic phase when returned to the solvent-extraction circuit in the spent electrolyte. Many of these operations prefer to operate with higher levels of iron reporting to the advance electrolyte, as appropriate control of the Fe(II)/Fe(III) couple will ensure that manganese remains in the benign Mn(II) form. A new reagent, LS 4202, designed by Cytec, now offers the possibility of tailoring the iron co-extraction, so that appropriate Cu:Fe selectivity can be achieved in the solvent-extraction operation to maintain an electrolyte Fe:Mn mass ratio of >10:1, while retaining the other benefits offered by ester-modified aldoximes. The results of an integrated solvent extraction-electrowinning pilot-plant trial are presented, in which the performances of the conventional extractants ACORGA® M.5774 and LIX® 984N are compared with LS 4202. The Cu:Fe selectivity is demonstrated, along with results on the transfer of other impurities to the advance electrolyte.

Jan 1, 2007

By Sunil Koppalkar, A. R. Laplante

"A Pilot Plant was installed in one of the grinding circuits of the Dome Mill, Ontario, Canada. Tests were conducted on a KCCD12 Knelson Concentrator to systematically analyze the effect of operating variables on the performance. The main objective of this test work was to explore the effect of very coarse (6 mm) feed size on GRG recovery and performance of the Knelson concentrator. Preliminary results have shown that coarse feed size is deleterious to maximizing recovery. Size-by-size GRG recoveries have shown an unusual trend in the sense that recoveries do not decrease monotonically with decreasing gold particle size. Similar trend observed in one other full-scale unit has been compared. The observed trend is probably linked to the feed size distribution and top size.INTRODUCTIONKnelson Concentrators are the most widely used semi-continues centrifuge gravity separation units for the recovery of gold and platinum group minerals (Xiao and Laplante 2004). The main advantages over the competing centrifugal gravity units are their design, operating simplicity and good separation efficiency that make them the most common choice for gravity circuit. Despite some characterization at bench scale and a limited characterization at full scale, there is a lack of a comprehensive study of impact of operating variables on efficiency that reflects realistic full scale operating practice. GRG characterization studies, at bench scale, on these units provide information about the occurrence of gold in ore samples but fail to provide adequate information about the effect of operating variables for full-scale units. It is well known fact that such work is difficult to undertake on full-scale units owing to the difficulties involved in sampling and systematic variation of operating parameters. To tackle these problems, a pilot facility consisting of a 12-in CD Knelson Concentrator, a feed screen and tailing pump was installed in one of the grinding circuits of Dome Mill. This paper describes the work carried out and the results.Porcupine Joint Venture (PJV)Porcupine Joint Venture was formed in 2002 between Placer Dome Inc. and Kinross Gold Corporation. The JV utilizes the milling capacity of the Dome Mill to process ore from Placer Dome and Kinross mines. The Dome Mill circuit has gravity concentration, cyanidation and CIP circuits to recover gold. Gravity recovery has been used at Dome Mill since inception to recover gold: first by using conventional jigs, which were eventually replaced by two Knelson Concentrators in 1993, one in each of the grinding circuits. Three more Knelsons joined the circuit in 2002 to improve gravity recovery. An Acacia Intensive Leach Reactor was also added in 2002 to process gold concentrates replacing shaking tables (Chong et al 2004)."

Jan 1, 2007

By L. Tapia

The main disturbance for stability in primary grinding using SAG mills is related to continuous changes in the ore being fed to the plant, such as size and hardness. Searching for stability is the first step to accomplish, before trying to maximize the mill throughput. The time variability in the characteristics of the ore being fed from the mine to the plant must be known or inferred to perform adaptive changes in the grinding process control. In day to day operation, such information is not available in real time. Transport times and inventories between the mine and the plant complicate the situation. Under this scenario, Minera Los Pelambres implemented a grinding optimization strategy, based on the real time analysis of certain process variables, such as ore size, mill current consumption, pebble generation and throughput. As a result, both grindability and stability indexes are inferred. This is equivalent to inferring the ore characteristics by knowing its effect on the grinding behavior. These two indexes permit control of the SAG mill total charge level and hence, allow optimization of throughput by means of an expert control system.

Jan 1, 2007