Search Documents

By A. McLean, Q. R. Yang, Y. D. Yang, G. F. Zhang, P. Wu

A considerable amount of waste slag from the pyrite roasting process is discharged every year. Recovery of iron from the waste slag is of great interest for comprehensive use of mineral resource, reduction of environment impact and improvement of economical benefit to related companies. The objectives of the present work are focused on: (1) Compare various procedures for recovery of iron from the waste slag and select a best procedure for industrial trial which is roasting of the waste slag under reducing condition followed by magnetic separation; (2) Investigate the optimum conditions for maximum recovery of iron from the waste slag. The experimental result shows that under the treatment condition found in this work about 36 to 40% of the iron oxide was recovered from the waste slag, where the iron content in the concentrate is 57%. The total recovery ratio of iron, up to 70%, from the waste slag was achieved. After the treatment, sulphur content in the waste slag was reduced significantly and gangue materials, such as SiO2, Al2O3 and TiO2, were reduced effectively.

Jan 1, 2011

By B. Tougas

Recycling of titanium represents an important economic activity due to high cost of the material and the amount of returns of machined parts which represent the bulk of finished titanium products (typical "buy to fly" of 10 in the aeronautic industry). In the present work, the metallurgical quality of 76 mm in diameter and 20 cm ingots poured in coated graphite mold will be assessed against the nature and condition of application of 4 coatings namely aluminum oxide, yttrium oxide, zirconium oxide and zirconium oxide with 4% aluminum oxide. The metallurgical quality has been evaluated in terms of alpha case thickness, microstructure and composition. Microhardness from surface will be assessed against casting conditions. Least square regression analysis have been use to optimize casting conditions.

Jan 1, 2011

By J. Kang

There is increasing demand to utilize aluminium alloy sheets and their spot welds by the automotive industry. While traditional uniaxial tensile tests only determine mechanical properties to small strain, direct measurement of the constitutive behaviour of aluminium alloy spot welds at large strain remains a challenge. A technique was successfully developed using digital image correlation coupled with shear tests to directly measure the constitutive behaviour of an AA6022-T4 spot weld to large strains. The results show that the spot welding process not only decreases the yield strength but also lowers the work hardening rate of the nugget versus the base material. Details of sample preparation, experimental approach and results will be discussed.

Jan 1, 2011

By Michel Guillot

Gaz metal arc welding is commonly used for producing large frames and assemblies. Even for light aluminum and thin wall assemblies, the GMAW technique is increasingly preferred over the GTAW technique. This is particularly true where the welding gun motion is achieved accurately with automated or robotic systems and when using pulsed or regulated metal deposition. In this study, butt joints in floor welding position are tested at speed ranging from 1.5 to 16 m/min. Attempts are made of find parameters providing good and repeatable joint quality with minimal distortion and good appearance even at high travelling speeds. Taguchi experimental plans are proposed with different parameters tested with sheet metal samples. The parameters include typical GMAW machine settings, joint preparation geometries, wire gages, gun angles, wire feeds, and more. The robot motion speed and the proximity of the part are also considered. Direct monitoring of machine welding current and voltage is achieved. Once is found the best set of parameter settings, additional tests are carried out to verify the repeatability of weld quality. Secondly, these conditions are applied for joining and testing a floor panel made of several extrusions. Weld quality is established with Vickers micro-hardness measurements, cross section geometries of the weld pool including penetration, tensile tests and metallographic observations to establish the amount of porosity and weld microstructure in the HAZ.

Jan 1, 2011

By F. Rashchi, N. Naseri Joda

Recycling of electronic wastes is an important subject both from an environmental point of view and also the recovery of valuable materials. In this research, PC board scraps were leached to recover Cu, Ag, Au and Pd. Due to the high cost of the shredding process and to avoid secondary pollution from odors and dusts, board scraps were cut into 5X5 cm2 pieces. To determine the most effective leachant, aqua regia, nitric acid, hydrochloric acid, ammonium persulfate and potassium persulfate were tested. The effect of the leaching parameters, the leachant concentration, temperature, leaching time and liquid to solid ratio were studied and optimized using response surface methodology.

Jan 1, 2011

By Y. Zedan

Cutting fluids play important roles during machining, including the reduction of friction and temperature. Using a cutting fluid, however, degrades the quality of the environment and increases machining costs. The aim of the present research work is to study the effect of cutting fluids and their interactions with cutting parameters on the quality of holes during the drilling of 6061-T6 aluminum alloys. The lubrication types and modes investigated are dry machining, flood lubricant machining and minimum quantity lubrication machining (MQL), while the part quality criteria include the surface finish, the dimensional accuracy, and burr forms and sizes. A scanning electron microscope (SEM) was used to investigate the formation of built-up edges (BUE) in the drill flutes as well as the surface texture of drilled holes. It was found that dry machining and MQL machining can produce parts having quality levels comparable to those obtained in wet machining, when using the optimal cutting conditions.

Jan 1, 2011

By A. Luckita, A. Samtani, R. Barus, J. R. Donald, J. Syarifuddin

In conventional Rotary Kiln-Electric Furnace (RK-EF) laterite nickel processing, management of dust continues to be problematic. A more efficient processing of dust represents an opportunity for energy efficiency, increased production, and productivity. PT International Nickel Indonesia (PTI), together with Vale Base Metals Technology Development (VBMTD), has successfully developed and implemented a novel flowsheet enhancement that capitalizes on these opportunities. In the novel flowsheet, the dust recycle stream is moved forward in the RK-EF laterite nickel smelting process. The dust is injected into the kiln's main burner, as opposed to being recycled to the dryers. A similar treatment of dust is commonly practiced in the cement industry; however, application to nickel smelters has not been fully developed to date. This paper describes this dust insufflation technology, the process through which it was developed for laterite nickel processing, and summarizes the lessons learned. A key conclusion is that successful new technology development requires a multi-disciplinary team involving members from research and development, study management, engineering consulting firms, project implementation management, process technology and operations.

Jan 1, 2011

By S. A. Bunk, E. C. Eccleston, J. J. Amsden

Fluidized bed technology has been widely applied to mineral and metallurgical processes. Over the years, modeling of fluidization technology has progressed to a level at which basic design parameters can usually be defined based on empirical correlations. In addition, scale-up considerations have become better understood, and significant advances have been made in the area of computer simulation. Despite these advances, fluidization is a complex phenomenon, and modeling tools remain limited in their ability to simultaneously model both fluidization and chemical process parameters. As a result, almost all mineral and metallurgical applications of fluidized bed technology require pilot testing prior commercial scale design. This paper outlines pilot plant testing requirements and process development considerations for development of low technical risk commercial designs.

Jan 1, 2011

By S. M. J. Mirazimi, F. Rashchi

Recovery of vanadium from LD (Linz-Donawits) converter slag was evaluated by means of microbial leaching. Vanadium leaching was performed in two stages. In the first stage, the bacteria were grown in a culture medium and in the second stage; vanadium containing slag was added to the metabolites produced by bacteria. Bioleaching was performed using heterotrophic bacteria Pseudomonas Putída. Control tests without bacteria inoculation were also performed and the results were compared with bioleaching outcomes. Optimal conditions for the bioleaching of vanadium containing slag were determined.

Jan 1, 2011

By W. Hardtke, B. Perry

Model reconciliation problems at the low-grade, high-nugget Phoenix gold-copper deposit led to an examination of the influence of production decisions on ore-waste classification. A conditional simulation study of the deposit was used as the basis for: 1) quantification of dilution at different bench heights, 2) quantification of ore-waste misclassification relative to bench heights and cut-off wades, and 3) determination of an appropriate number of samples to optimize ore-control polygon definition. Actual reconciliation data were empirically used to support conclusions. Simulations of both gold and copper were combined through net revenue modelling. These simulations increased understanding of the nature of the deposit and provided insight for resource modeling and mine planning.

Jan 1, 2011

By D. F. Machuca-Mory

The new algorithm for high-order simulation of ore deposit grades termed HOSIM is based on the concept of spatial cumulants. The algorithm is tested using data from Apensu, a structurally controlled gold deposit in Ghana. The required high-order spatial structures are obtained from a training image or analogue of the deposit. Using the available drillhole data and training image, HOSIM realizations are able to model well the grades and geometry of the large and well sampled mineralized structures. However, under-sampled small structures remain difficult to model. HOSIM offers a promising alternative for the spatial simulation of complex non-Gaussian orebody attributes of interest.

Jan 1, 2011

The process of gold recovery by gravity concentration is incorporated in the metal recovery flowsheet at seven Newmont Mining Corporation owned mining operations in Australia, North America and Africa. In 2009 gold recovered by gravity processing was equivalent to nine percent of Newmont's total gold sales of 5.3 million ounces. This paper will discuss these applications in detail including a review of plant flowsheets and presentation of recent operating results. Operating performance will be discussed with reference to ore characterisation procedures, interpretation of results, design considerations and optimisation practices as they relate to the recovery of gold by gravity concentration.

Jan 1, 2011

By Tony Moore, Peter Riccio

"MMG (Minerals and Metals Group) operates the LXML Sepon’s mineral processing facility located 40 kilometers north of the town of Sepon, in the Savannakhet Province, Lao PDR. The Sepon copper plant produces 70,000 tons/year of LME grade A copper cathode using leachautoclave- SX/EW-flotation technology (Baxter et al., 2003). Pyrite recovery in the flotation circuit is critical to the operation, as it is used to generate acid and soluble ferric ion for the leach circuit. Low pyrite recovery has been an on-going challenge in the flotation circuit. Final tailings characterization work done by Ian Wark Research Institute (Bassell et al., 2006) showed that the pyrite losses to the tailings are made up of a combination of coarse liberated particles and finer particles that have been coated by clay fines.In December of 2005, a joint Cytec-MMG technical program was initiated to address the pyrite recovery issue. A series of diagnostic tests were performed in the Cytec Stamford Research Facility using synthetic plant water showing that the collector was precipitating as a metal salt and was unavailable for mineral attachment. The tests also identified several collector chemistries that would likely be robust in the low pH (< 1), high dissolved metal ion environment and will not complex with metal ions in solution. With the support of the Sepon on-site engineers, an extensive, successful laboratory program was completed, which was subsequently followed by on-plant testing that showed a step wise improvement in pyrite recovery.INTRODUCTIONLow pyrite recovery has been an ongoing problem in the flotation circuit at Sepon. Sulfur recovery (indirect measure of pyrite) was improved from 40% to 65%-75% in mid-2005 when on site laboratory work confirmed that AERO® 8045 Promoter was a more effective collector then AERO® 407 Promoter. However, sulfur recoveries above 65% could never be achieved. Sepon requested the Ian Wark Research Institute to complete a surface analysis study using Scanning Electron Microscopy, X-ray Photoelectron Spectroscopy, and Time-of-Flight Secondary Ion Mass Spectroscopy to determine if clay coated pyrite played a role. It was concluded that the pyrite losses to the tailings are made up of a combination of coarse (+ 100µm) liberated particles and finer (-74µm) particles that have been coated by clay fines. The majority of the losses appear to be due to the former. In December of 2005, a series of diagnostic tests were performed in Stamford using synthetic plant water in order to identify what chemistries would likely be robust in the slimy low pH and high dissolved metal ion solution environment. Results showed that several chemistries would not complex with ferric, ferrous or copper in solution and therefore should perform well in the Sepon flotation. The incumbent collector, AERO® 8045 Promoter was complexing with metal ions in solution. This resulted in the collector not being available for adsorption onto pyrite."

Jan 1, 2011

By B. Wasmund, B. Haneman, G. Sheehan

Success in implementing new technology for metallurgical processes is not a foregone conclusion: This paper includes a survey of 23 new technology-based metallurgical plant start-ups, in which the authors have identified 7 successes, 9 difficult start-ups, and 7 failures. Success is defined not only as meeting the schedule and budget to the end of mechanical completion; the key goal is a fast ramp up to the full design production level, with minimum plant and equipment modifications required after start-up. This paper sets out the key factors that underlie achievement of a quick production ramp up curve, as determined from the authors&apos; project experiences and a quantitative analysis of over twenty metallurgical plant start-ups, both pyrometallurgical and hydrometallurgical. Thorough test-work and pilot plants, plus appropriate scale-up to the full commercial plant, are key determinants of success in implementing new technology in metallurgical processes. Another critical factor is the number of new elements and their interactions. Project phasing is also particularly important for new technology projects, with appropriate review after each phase to develop a risk mitigation plan for the subsequent phase. New technology projects need committed champions to advance the project in the face of sceptics, but also require dispassionate and unbiased experts to ask the hard questions. As a project evolves, it is important to periodically question the appropriateness of assumptions, as well as to re-assess the relevance and completeness of data from test-work I pilot plants I industrial analogues. Sufficient human and financial resources are required to complete the often arduous implementation phase. During the ramp-up period, the operation generates little positive cash flow; however, significant expertise and capital are required for the de-bottlenecking projects that are often necessary to reach the plant&apos;s design output level.

Jan 1, 2011

By Q. H. Bui

The elastoplastic self-consistent model is one of the effective models to study the initial microstructure effect on the mechanical behavior of bulk materials. However, the use of this micromechanics-based model which takes into account only the Hall-Petch relationship at grain level for predicting the grain sized effects on the strength of the deformed materials is not accurate yet because of the fact that the dislocation density contributes also to the strengthening of this kind of materials. In this study, a modification made to the Hill-Hutchinson elastoplastic self-consistent model was proposed for investigating the microstructure dependence of the mechanical behavior of cold-drawn 6063 aluminium tubes. Because of the novel modification, an estimation procedure with two steps was required to identify the parameters of this micromechanical model. An acceptable agreement between experimental and theoretical stress-strain curves was achieved.

Jan 1, 2011

By W. van der Merwe

With the gold industry looking to process more complex ores, the online measurement and control of cyanide addition to the gold leaching circuit has become more crucial. This paper compares the two commonly employed "free" cyanide online analysis methods (amperometric and potentiometric end-point silver nitrate titration) with the common site laboratory rhodanine endpoint silver nitrate titration and ion selective electrode methods. Measurement differences between these methods are presented and discussed for cyanide solutions containing copper and zinc with varying cyanide to metal ion ratios. The resulting cyanide available to leach gold is also compared with these measurements.

Jan 1, 2011

By A. Djebara

Today, indoor air quality, especially in manufacturing industries, is of great interest due to the use of new processes and advanced materials such as those containing nanoparticles. Manufacturing processes generate aerosols (dry or wet) which can be detrimental to occupational health and safety and to the environment. Controlling metallic particle emissions during machining processes should limit their formation at the source, and thus minimize the risk of exposure; this at-source reduction requires the characterization of the particle emitted (size, nature, concentration, etc). The metrics normally used in characterizing fine and ultrafine particles include the mass concentration, the specific surface and the number concentration. Most of these metrics are affected by the size, the geometry and the density of the measured particles. Information about the form and the real size of the particles is thus very important. A procedure for collecting and characterizing fine and ultrafine metallic particles was developed and applied to the study of particles emission during the machining of aluminum alloys. It was found that metallic particles emitted during the machining of aluminum alloys are of various shapes and sizes, and this information must be taken into account when characterizing these particles.

Jan 1, 2011

By E. Lovera

ABSTRACT: The current study analyzes the feasibility of an odd operation: to obtain, using a properly tailored drilling and blasting scheme, blocks suitable for the production of dimension stone from tunnel driving. Clearly, a compromise must be found between the rate of progression and the achievement of workable blocks. As a case study, a civil work under consideration in northern Italy was examined. The work was planned to cross a conglomerate that has traditionally been locally exploited for the production of highly prized paving and lining stones with excellent strength and aesthetic features. Natural exposures and mined-out quarries were available for tests. The relevant rock data are given, blast designs are shown (within the limitations of contour accuracy), and the test program is described.

Jan 1, 2011

By S. Brophy

Controlled Short Circuit ? Metal Inert Gas (CSC-MIG) welding is a process that can be referred as a "Cold Welding" technology. The CSC process is based on accurate control of the welding wire position, thus the mandatory requirement for the automation of the process. One of the main advantages of the CSC-MIG process is the rapid solidification of the deposited material, resulting in weldments displaying low porosity contents, and enabling the joining of thin sheet materials. These characteristics render this process an ideal one for freeforming of components, where rapid solidification would be efficacious. This presentation will focus on the progress made towards the freeforming of Al-based components in the NAIN laboratory at McGill University. The relationship between the filler metal used, freeforming (deposition) parameters, resulting microstructure and mechanical properties will be presented.

Jan 1, 2011

By Martin Lebeuf

The phenomena occurring in the cathode and at the cathode surface of aluminum electrolysis cells are very important in regards to cathode voltage drop and cathode wear. In the current study, laboratory-scale aluminum electrolysis cell cathodes were analyzed by X-ray microtomography. This technique allows an excellent visualization of the distribution of different substances, if their respective X-ray attenuation coefficients are different enough. In the current case, the important difference in the mean atomic number between cryolitic bath and graphitic carbon results in good contrasts. The volumetric bath penetration profile, porosity and impurities distribution in the cathode were thus obtained. Furthermore, metallic impurities and bath heterogeneities were observed at the cathode surface. Observations were also made with Scanning Electron Microscopy - Energy Dispersive Spectroscopy (SEM-EDS).

Jan 1, 2011