Search Documents

By A. Brian Hawkins

"When pyrite oxidizes in dark grey/black, calcareous, mudrocks or in argillaceous limestones, ferrous sulfate is formed and sulfuric acid is released. The sulfuric acid combines with the calcite present in the rock and calcium sulfate (gypsum) develops. When this occurs on the outer edges of aggregate particles, the gypsum forms in the matrix hence there may be little expansion of the general material. However, when the chemical reactions occur within the rock fragments, particularly on microscopic, clayrich, laminae, the developing crystals exert a significant pressure on the host material. If the rock is medium strong to strong, the force of crystallization splits the rock along the weaker planes, facilitating the ingress of the oxidizing agents and the continuation of the chemical reactions. In addition to causing dilation/heave, some of the engineering properties of the material are changed, including the strength, Los Angeles value, water absorption etc. As a consequence material, which at the time of quarrying would be acceptable for use beneath floors or hardstandings, would no longer be considered suitable.INTRODUCTIONMudrocks accreting in aerobic environments are frequently disturbed by organisms and as a consequence there is often little sign of bedding. In contrast, sediments which have formed in anoxic environments commonly have distinct bedding planes which, because of the grain size of the accreting material, are often smooth and planar. These rocks are frequently referred to as shales, which O’Brien and Slatt (1990) define as “characterised by a finely laminated structure, which imparts a fissility approximately parallel to the bedding.” This should not be confused with rhythmic bedding where the variation in grain size results in lithological laminations or colour changes.Early geologists, in the stratigraphic naming of rocks, often used the term shale for material which is now more likely to be described as mudstone or mudrock (Hawkins and Pinches, 1992). In many contexts, the width of the bedding is an important factor, not only in determining the rock name but also in indicating the potential engineering characteristics. Until recently a shale was considered to have bedding separations of less than 20mm, i.e. the bedding was described as laminated. However, in an engineering context, EN 14689: 2003, Annex A, defines shale by specifying a bedding thickness of < 6mm; such a material would be described as thinly laminated in BS 5930:1999. Ideally the term shale should be abandoned and be replaced by fissile mudstone or fissile mudrock."

Jan 1, 2015

By H. E. T. Haultain

I HAVE considerable hesitation in preparing and presenting this paper. These machines have been such an intimate part of my own experiences and predilections for such a long time that J would find it difficult to tell the story in an impersonal way. They have had several attractions for me. They were needed for the study of the fundamental features of modern milling, size analysis and accurate batch concentration of the very fine particles. I had been a millman once, a real operating millman, and, when I became academic". I always had the craving to link the academic laboratory with the field, as Rittinger and Richards had done. My first milling experience was with a small concentrator at a tin mine in Bohemia, forty-seven years ago. There was no assay office and the testing of our tailings was by means of a "Vanning Shovel", introduced from Cornwall by Captain Josiah Thomas, the great Josiah of Dolcoath, some fifteen years previously. This was a most effective instrument and it has always been a puzzle to me that it has not been more universally used by millmen. Later, at Freiberg, on the other side of the Erz Gebirge from the tin mine, I was introduced to the "Sichertrog", made out of wood shaped something like a very shallow boat or an elongated saucer, a most effective piece of apparatus when. the difficult technique of handling it was once achieved. Later, in the Slocan in British Columbia, my partner, the late Maurice Bucke, used a short length of flat trough or launder suspended by four wires, with which he got very satisfactory results as a small batch concentrator. In the University laboratory we had frequent need for something of this kind, and many efforts were made to solve the problem. With W. E. Johnston, we were working on the problem of gold-bearing telluride ores, which called insistently for a separation of the very fine telluride particles which existed only in minute quantities in the Kirkland Lake ores. Under this spur there finally developed the Superpanner, which is a mechanized combination of the Vanning Shovel, the Sichertrog, and the Maurice Bucke suspended launder.

Jan 1, 1937

By R. F. Pilgrim

"This first chapter of the SPOC Manual 1s intended as a general introduction to all the other chapters in which the mineral process evaluation and optimization methodology is presented. This chapter also provides a brief description of available software for mainframe and m1crocomputers and provides information on its distribution by the Technology Information Division. CANMETRESUMECe premier chapitre du manuel SPOC est un guide général qui présente les autres chapitres ou l'on traite de la méthodologie d'évaluation et d'optimisation des procédés miméralurgiques. Le lecteur y trouvera aussi une description sommaire des programmes de calcul développés pour ordinateurs centraux et pour micro-ordinateurs ainsi que la façon de les obtenir de la Division de l'information technologique du CANMETComputer simulation of mineral processes has slowly emerged as an established branch of activity in A&D centres and in several teaching institutions after decades of slow progress. Substantial efforts to develop application software based on years of research on process modelling are being pursued in many countries ( 1 .2,3,4.5). The late BO's should see a flurry of success stones about significant leaps of productivity achieved in several plants through systematic process evaluation and computer simulation studies.In Canada. the SPOC project (Simulated Processrng of Ore and Coal) was initiated at CAN MET in 1980 with the obJective of developing and transferrrng to the mineral rndustry a computer-based methodology for process evaluation and optimization. The proiect deliverables include:- an engineering manual covering most aspects of off-line computer simulation:- a bank of FORTRAN software accessible through data communication lines for user familiarization and distributed at a nominal cost in source form by CANMETThe yearly progress reports of the project contain detailed information on the project elements since 1980 16). The context of SPOC can be summed up by quoting Gordon Agar""s 1975 statement during a workshop on research needs in the mineral industry: ""What is needed is a joint effort between the academic community and one or more enliglitened industrial concerns. The effort will have to be an iterative one with data collection followed by testing the model modification of the model (s), more testing prediction, modification. data collection and so on (7). A few parallel in1- t1atives had been reported in papers or research contract reports (8, 9) but there was an obvious need for CANMET to bridge the gap between the R&D and the production sectors by undertaking a project that would document past applications and induce a new generation of initiatives through the consol1dat1on and transfer of suitable manuals and software. The effort took shape as the CANMET SPOC pro1ect in which methodology transfer was to play a key role (10)."

Jan 1, 1986

By J. Flemming, R. O. Burt

"The Tanco pegmatite is located in the Bird River greenstone belt of southeastern Manitoba approximately 160 km northeast of Winnipeg (Figure 1). This pegmatite body was discovered in 1929 and subsequently attempts were made to exploit it for tin by Jack Nutt Mines Ltd. and later in the middle 1950's by Montgary Oil Ltd., who extensively developed but did not produce from, its lithium deposits. In 1966 systematic investigation of the pegmatite as a potential source of tantalum led to the founding of Tantalum Mining Corporation of Canada Ltd. (TANGO) in 1967 and production of tantalum concentrates from the Bernie Lake mine commenced in 1969. Tanco is currently jointly owned by Hudson Bay Mining and Smelting Co., Cabot Beryl co Inc. of Boston, and the Province of Manitoba. (Williams and others 1978, Burt 1979, Burt and others 1982), continued until the end of 1982, when, due to falling demand and prices, operations were suspended.During the 1970's Tanco had investigated the potential of the lithium orebody; carrying our research into both the concentration of the ore and into the production of lithium chemicals. However lithium chemicals were in an over-supply situation, due in part to the production from Chilean brine deposits (Buckley, 1983), and Tanco' s own plans were put into abeyance. The potential alternative market, the direct use of concentrates in the glass and ceramics industry, did not at the time justify the cost of constructing a new plant."

Jan 1, 1986

By R. N. Chakravorty, K. K. Feng

"There is growing evidence that modern methods of mining coal increase the risk of spontaneous combustion. Seemingly unimportant at this time, this hazard could prove to be a barrier to growth and development of the coal industry in some areas of Canada. The paper presents bedrock knowledge on spontaneous combustion gathered by scanning and evaluating current technical and research literature. Special efforts have been made to identify significant coal and environmental factors and to establish criteria for susceptibility. In addition to the state-of-the-art knowledge, preliminary results from on-going studies are discussed."

Jan 1, 1973

By K. K. Feng

"Spontaneous combustion has always been a problem in coal mines and is identified mainly with the mining of low-rank coals. The liability of coals to spontaneous heating is only one of the factors in determining whether spontaneous combustion will occur. However, knowledge of the relative oxidizability of the coal is a useful factor to take into consideration when selecting new coal seams and mining methods for future mine development.Four methods (static isothermal, ignitability, adiabatic and dynamic) have been used to compare the relative liability of Canadian coal to spontaneous combustion and to investigate the mechanism of spontaneous combustion of these coals. Among these f our methods, the static isothermal method is considered to be the best indicator of the susceptibility of various coals to spontaneous combustion. Western mountain coal adsorbs more oxygen and has a higher tendency to undergo spontaneous combustion than the Harbour seam coal of Nova Scotia. It has also been observed that a higher methane content in coal will indicate a lower liability to spontaneous heating."

Jan 1, 1985

By T. Scully

Since early days in coal mining, it has been known that some coals and the carbonaceous materials associated with them will heat and fire spontaneously. Many theories have been advanced to account for this phenomenon, but it is only within comparatively recent years that any scientific research has been carried out to determine the causes of this heating, the conditions which bring about its occurrence, and the reason why different coals heat with a varying degree of readiness. So far, this research has not cleared up these points entirely, but a great advance has been made in our knowledge of the matter. In general, any coal will fire spontaneously, although with a varying degree of readiness, provided conditions for its doing so are favourable enough. These conditions are that the coal must be in a fine state of division, that sufficient oxygen must be present for rapid oxidation, and that the air current passing must be so small that it is insufficient to carry off the heat produced by this oxidation. Many other minor factors, however, contribute to bring about spontaneous heating, either by producing initial heat themselves or by inducing the other major conditions.

Jan 1, 1931

By D. Brossman

"The virtue of spray drying is that it is a drying method, and so far the only one by which it is possible in one operation to divide a mineral concentrate into its basic primary particles.,In so doing, each particle gets the same treatment and the result is a dry concentrate more homogeneous than any other known concentrate drying process. This is particularly good for a flash furnace requiring a bone dry finely divided feed. The spray dryer also features a very short residence time and due to the very quick operation the solids are kept cool thus preventing any risk of fire or explosions on these pyrophoric materials.There are many spray dryers now in operation in the mining industry and one of the latest applications is in South Africa where a spray dryer is treating a copper-nickel platinum concentrate which is, after drying, fed toan electric arc furnace. Experience has shown that the concentrate should contain 4% moisture for the furnace, and this is achieved by drying the concentrate bone dry and then back-mixing with thickener underflow pulp to provide an extremely homogeneous feed to the smelter. As mentioned before, mixing with pulp would be more of an advantage because we would not be evaporating water which would have to be added again afterwards.One of the first spray dryers to go in was at Western Mining Corporation in Kambalda in Western Australia. (A series of slides was then shown)."

Jan 1, 1972

By R. J. MacLeod

"INTRODUCTIONThe removal of water or liquid from slurries and solutions is a procedure generally present in many process industries. This has prompted the development of many mechanical and thermal devices with which, I have no doubt you are al1 familiar.In the mining industry, beneficiation of ores necessitates ' the removal of water or other 1iquid from the concentrate material. The most common method of accomplishing this is by means of thickeners, vacuum filters and rotary dryers, generally all three and in that order;The use of spray drying techniques to obtain the same end has many advantages and these will be outlined here.THE PRINCIPLE OF SPRAY DRYINGA Spray Dryer consists of a cyclone shaped chamber where hot air and atomized concentrate are introduced in the upper section. (Sec figure No. 1). Efficient mixing of these two streams produce dry concentrate and moist spent air, both of which are removed from the base of the chamber.Thermal dewatering involves the product ion of heat and spray drying has no special requirements in this area. Generally a direct fired air heater is used and the products of combustion whether they stem from the use of gas, oil or coal fuel go into the spray dryer along with quench or dilution air which is used to reduce the combustion gases to the desired temperature. This generally lies in the range of 1,000 to 1,600° F. In spite of these relatively high inlet temperatures, the spray drying process eliminates the need for refractory lining or indeed any special heat resistant metals except on the air inlet ducting. Waste heat may also be used even if a significant amount of contamination is present."

Jan 1, 1972

By Yoginder P. Chugh

This paper discusses design of sprays systems for dust control around a continuous miner (CM) in about 4.2 m (14 ft.) high mining areas with about 1.0 m to 2.0 m (3-6 ft.) of out-of-seam dilution mining. The challenges included low air volumes and velocity at the end of the line curtain, dust produced from out-of-seam dilution rock being very fine with 50% of the particles less than 10 micron, poor capture of aerosol through scrubber suction inlets, dust escaping through the sides of the loading pan in mining high areas, overloading of dust-laden air in the wet-scrubber, and dust rollback toward workers. The challenges were resolved through CFD modeling of airflows; improved line curtain installation, redesign and varying the spatial locations of spray systems as compared to low mining height areas. Water sprays on CM is the primary engineering control for dust control in coal mining. In 2010, the authors developed several spray system concepts for dust control (Chugh, Patwardhan, Gurley, & Hirschi (2009), Chugh & Gurley (2009), Chugh 2012). These included increased contact time between dust particles and water droplets, improved potential for the dust aerosol to be sucked in through suction inlets, and reduced dust-roll back to the operators and workers. CFD modeling was used to understand airflow patterns around mining areas and to identify spatial locations for sprays to minimize dust exposure of CM operator (CMO), haulage unit operator (HUO), and workers downwind of the operating CM in the last open crosscut (LOXC). Face area ventilation plays a key role in dilution and removal of dust generated by mining operations. High mining heights and large pillar sizes associated with longwall mining reduce the air volume reaching the face area to achieve good dust dilution.

Aug 1, 2013

By D. O. DeGagné, J. F. Archibald

Spray-on polymer linings, as partial or full replacement for traditional forms of area rock support, have seen rapid growth in interest within Canada. A wide variety of lining types, ranging from polymer chemical to water-based cementitious materials, have been developed and commercially introduced to the underground mining market. Following approximately one decade of development work, several general conclusions have been reached regarding the performance of this class of area support media, these being that: health and safety assessment of the broad range of materials has shown the majority of them to be acceptable and safe for underground use; significant ground support potential can be offered by them, being equivalent to or better than capabilities offered by traditional support forms such as bolt-and-screen or shotcrete, and; their abilities to be rapidly deployed and provide near instantaneous support restraint offer considerable operational and cost benefits to underground operators. A review of currently available liner materials, their historic development within the Canadian mining industry, and overviews of support, health and safety, operational considerations and cost benefits are provided in this paper.

Jan 1, 2001

By Robert D. Brown

"Important tax changes, many of them of direct interest to the mining industry, were contained in the budgets brought down by federal and provincial finance ministers across Canada this spring. This month, Tax Notes presents a brief summary of important tax changes introduced at the federal and provincial levels in the last few months.IntroductionIn the March 1980 issue of the CIM Bulletin, Tax Notes surmised that the short-lived 1979 budget proposals of the former Conservative government offered a unique glimpse of budgetary changes that might be unfolded in 1980. Scene II of this ""now you see it-now you don&apos;t"" drama opened on April 21, 1980, when Finance Minister Allen MacEachen, in an ""economic statement""&apos; reintroduced a selection of tax proposals taken from the ill-fated Conservative&apos; budget of December 11, 1979, but refused to bring forward major new proposals in tax and finance.Mr. MacEachen proposed a 5% surtax on federal corporation income tax to apply in the 2 years from January 1, 1980 to December 31, 1981, as a slightly modified version of the same surtax proposed by former Finance Minister Crosbie in his December budget address. Mr. MacEachen also reintroduced a number of technical amendments which would affect the taxation of mining income in certain instances. In addition, a large number of other tax proposals suggested in the previous Conservative budget were also reintroduced, although there are some notable omissions."

Jan 1, 1980

By J .. A. Nemes, I. Ragai

This paper discusses one of the common problems associated with sheet metal forming processes, which is spring back. The materials presented here, stainless steel 410 and Inconel 718, are commonly used in aerospace applications for their superior material properties. Standard tensile tests were performed to determine their tensile properties, as well as material anisotropy. In addition, the effect of anisotropy on springback was assessed experimentally through simple multiple-bending experiments in different directions to the rolling direction. Finally, draw-bending experiments were carried out to study the effect of forming conditions, such as blank holding force, on the final springback angles of the formed parts. For both materials, it was found that the R-values measured for different sheets exhibited variation. However, the specimen orientation does not have a large effect on material tensile behavior or springback angle for simple bending. For the Inconel 718 specimens, the springback angle slightly increases with each stage of deformation during multiple bend experiments. The effect of the blank holding force on springback angles was also examined and found to have a significant effect on thin specimens.

Jan 1, 2006

By J. Kronsteiner, E. Kabliman

"In the present work, we developed a Smart Process Control Toolkit (SProC) as a single simulation environment for the modelling of materials microstructure and its interaction with the local microchemistry during manufacturing of semi-finished products. This toolkit supports the data communication between sub-sequent processing steps such as casting, homogenization, pre-heating to deformation, etc. The thermo-kinetical simulation software MatCalc of MatCalc Engineering© GmbH was used for modelling of precipitation kinetics, such as formation of primary and secondary phases and their evolution. An import/export functionality of the precipitation distribution after each processing step was implemented to follow the parameter history. For the evolution of the local microstructure, a Mean Dislocation Density based Model (MD2M) was used. This model consists of two parts: (1) Flow Stress Model for calculation of the total strength during the deformation and (2) Static Recrystallization Model for account of the recrystallization and grain growth after the deformation. Validation was done by a comparison of experimental and simulated hot compression tests of a conventional AA2024 alloy.INTRODUCTION Optimization of a semi-finished products quality, elimination of typical production issues and cost savings are of a great demand for supply industries. However, it is currently not feasible to investigate the whole manufacturing process in detail at an industrial level. Concerning the processing parameters, one must understand the correlation mechanisms between macroscopic properties and microscopic material behavior. Numerical simulations, which could reproduce the real processing conditions on the one hand, and employ a physically based modelling on the other, are thus attracting a lot of attention and their power is no longer under the question. It is well known that e.g. the total strength of the material depends directly on distribution of precipitation particles and mean grain size. In order to follow their evolution during the manufacturing process beginning from casting to the final semi-finished product, and thus be able to control the process, one should use the techniques which would at the same time reproduce experimental processing conditions of real size objects (e.g. sheet, extrusions, etc.) and account for the evolution of a local microstructure and its interaction with the microchemistry. A commonly used approach is to implement a model which would describe the evolution of microstructure based on a dislocation density approach into a user defined material subroutine of some finite element solver. There is, however, also an influence of the manufacturing process by e.g. the evolution of a local microchemistry (formation, transformation and dissolution of the precipitation particles) on the microstructure and thus the macroscopic material behavior. Thus, a method is needed to follow the variable history through the simulation of the whole production chain."

Jan 1, 2018

By W. T. Boyes, J. M. Harrison

"Squall Lake Gold Mines, Limited, owns a group of claims at Squall lake, northern Manitoba, about 75 miles east of Flin Flon and 3 to 4 miles north of the Nor-Acme mine at Snow lake. Gold mineralization was discovered in this locality several years prior to 1944, but it was only in that year that a comprehensive examination of the occurrences was begun. Development work to the end of 1946 has been encouraging and the deposits show interesting relations to rock structure.GEOLOGICAL SETTINGThe gold occurs in a sill of biotite-hornblende diorite at or near its contact with gneisses derived from arkosic sediments . In detail, the contact between the diorite and the arkose to the southeast of it is irregular, with interfingering of the two rock types. On the northwest side of the sill, between it and Squall lake, the rock is staurolite schist (see accompanying sketch-map).Several mineralized shear zones are known, of which those shown are the most important. Within the zones, the diorite is silicified and somewhat carbonatized. Fairly coarse arsenopyrite is the chief sulphide mineral in these zones but, locally, they contain also pyrite and pyrrhotite. Where quartz and chlorite are present, rather coarse gold is associated with them. In that part of the main zone where gold assays have been most consistent, the diorite is rich in albite."

Jan 1, 1954

By P. Massi

"Wholly owned by the Coniagas Mining Company, the oldest continuously listed mining company on the Toronto Stock Exchange, St. Andrew Goldfields is located on Hwy. 101 approximately 30 miles east of downtown Timmins, Ontario. Geographically situated on the Porcupine-Destor Fault, the mine and mill in Stock township is positioned in the heart of Northeastern Ontario's goldmining communities.In July 1988, a 600 ft. shaft, hoist, and compressors were already in place when construction started on a 500 T.P.D. capacity C.I.P. mill and crushing plant.By June 15, 1989 the mill was commissioned and attained the design capacity by August of that same year. Since then, changes to the circuit have increased throughput to 900 T.P.D. from two significantly different ore sources.Meeting the Ministry of the Environment's guidelines is an ongoing commitment utilizing the Inca S02 process in line between the tailings pond and secondary polishing pond.INTRODUCTIONExploration on what is now known as St Andrew Goldfields' Stock Township Mine was carried out ln the early l960 1 s by Hollinger Mines Ltd. The property was acquired by Quebec Sturgeon River Mines 1n 1973 and the main shaft was started ill 1979.When St Andrew Goldfields was incorporated 1n 1983, exploration and development commenced to identify the ore body. The company decided 1n 1987 to bring the Stock township property into production after an extensive feasibility study and testwork at Lakefield Research in Toronto. Leslie Engineering was contracted to design, engineer and procure al 1. equipment from the coarse ore bin to the tailings distribution system and backfill plant"

Jan 1, 1992

By L. M. Cumming

"The contact between dolomite of the St. George formation (Cambro-Ordovician) and limestone of the overlying Table Head formation (Middle Ordovician) is a regional disconformity. This is best illustrated from exposures on Pointe Riche Peninsula, near Table Point, and along Port au Port Bay. The contact occurs along 180 miles of the west coast of Newfoundland from St. John Island in the north to the western part of Port au Port Peninsula in the south. A disconformity of the same age occurs between the Romaine and Mingan formations on the north side of the Gulf of St. Lawrence.Dolomitic beds beneath the disconformity locally contain concentrations of base-metal sulphides. Sphalerite occurs in dolomite pseudobreccias of the St. George formation at Zinc Lake, 7 miles northeast of Daniels Harbour. The 'Western Newfoundland Lower-Middle Ordovician regional disconformity is interpreted as having originated on and near the edge of a broad platform, and to have provided an important regional geological control in the localization of zinc mineralization."

Jan 1, 1968

By Marvin E. Lane

Viburnum, located in the foothills of the Ozarks in south-east Missouri, is the site of a modern lead mining and milling operation. Two mines are currently producing a total of 5,000 tons per day and a third mine is in the final development stage, with full production scheduled for late this year (1964). These mines will supply the tonnage required to keep the Viburnum mill operating at a full capacity of 7,000 tons per day for many years. The efficient underground mining operation is completely trackless. Drill jumbos are used to break the ore in a room and pillar method of mining. Transloaders, or St. Joe shovels, and trucks do the loading and hauling. The Viburnum mill has a world-wide reputation as a most efficient operation. This is due to the extensive use of automatic process controls, and labour saving materials handling facilities. Introduction THE St. Joseph Lead Co., has operated lead mines in southeast Missouri for 100 years. These operations have been confined largely to the area called the

Jan 1, 1964

By Mostafa Benzaazoua

Les remblais en pâte cimentés sont de plus en plus utilisés dans les exploitations minières souterraines. Une autre alternative d?utilisation du remblai en pâte consiste à le pomper et à le stocker dans des empilements de surface. En plus d?avoir des avantages d?un point de vue de stabilité physique des ouvrages, le remblai en pâte cimenté en surface permettrait également de stabiliser les contaminants dans la matrice du remblai à l?aide du processus de solidification et de stabilisation. Dans cette étude, des remblais en pâte constitués d?un résidu minier sulfuré renfermant beaucoup d?arsenic et de différents liants ont été testés afin d?évaluer la stabilisation des contaminants dans la matrice de remblai. La méthode utilisée pour évaluer la stabilisation et la solidification des contaminants est le test de lixiviation en extracteur de Soxhlet. Les résultats géochimiques issus de ces essais ainsi que la caractérisation chimico-minéralogique des remblais lixiviés ont été analysés pour comprendre les phénomènes chimiques présents dans les remblais durant le temps de cure. Les résultats obtenus montrent que les sulfures présents dans les remblais étudiés (pyrite FeS2 et arsénopyrite FeAsS) s?oxydent et provoquent la dissolution des hydrates les plus vulnérables (dissolution de la portlandite Ca(OH)2 et/ou décalcification des gels CSH). Le calcium produit permet de précipiter les sulfates (essentiellement sous forme de gypse plus ou moins hydraté) et l?arsenic sous forme d?arséniates de calcium plus stables. Les différents liants utilisés donnent des résultats différents en termes de stabilisation et de solidification qui seront discutés dans cet article.

Nov 1, 2002

By Helen Morrison, Chris Staun, James Vaughan

"Mercury is introduced into the Bayer refining process as a trace element in bauxite. During the digestion stage, a portion of the mercury is extracted which partitions between the flash tank off-gas, vapour condensate and bauxite residue streams. A technology or treatment that stabilises mercury in the solid phase during digestion would prevent environmental management issues that may arise from the presence of mercury in condensate and non-condensable gases. This study examines the effect of process additives on the deportment of mercury under Bayer digestion conditions. Bauxite digestion experiments were conducted in batch autoclaves in the presence of additives. Process liquor was analysed for mercury content using a thermal desorption technique. Pyrite and copper hydroxide were evaluated for their suitability as additives.INTRODUCTIONMercury is an ancient metal characterised by electrochemical nobility, volatility, low solubility in water and a liquid state at room temperature (Holleman and Wiberg, 2001). The biogeochemical cycle of mercury is complex. Elemental mercury may enter the atmosphere due its volatility, where it can be transported long distances. After settling and adsorption to sediments, methylation is catalysed through microbial metabolism (Qureshi et al., 2009). Methylated mercury species are potent neurotoxins, and bioaccumulation of mercury is well documented, particularly in seafood (Kozin et al., 2013, Pan et al., 2014, Pollman, 2014). Environmental regulations for mercury emissions are becoming increasingly stringent (UNEP, 2015). Considerable research has already been performed and technologies developed for the remediation of mercury in wastewater and the trapping of mercury from industrial stack emissions. Wastewater technologies usually target ionised mercury using adsorbent, ion exchange and complexation mechanisms (Krishnan and Anirudhan, 2002, Li et al., 2015a, Chiarle et al., 2000), while stack emission technology is dominated by impregnated activated carbon adsorbents (Gao et al., 2013, Zheng et al., 2012). Related developments include piezoelectric amalgamating sensors for in line detection of gaseous elemental mercury in industrial stack emissions (Kabir et al., 2015, Sabri et al., 2011). There is a paucity of research regarding removal of mercury from the Bayer process."

Jan 1, 2016