Search Documents

By R Ibarra, H Solis, G Teowee, B E. Papillon

The authors have previously described a piezoelectric-based system to measure the dynamic pressure during actual detonation in the field. This technique is used in a water hammer test set-up where a donor detonator is fired first, with the pressure sensor and an acceptor electronic detonator placed underwater in a water tank, and maintained at a fixed distance away from the donor detonator. The functioning and timing of the acceptor detonator are captured using a customised microcontroller board called the water hammer timer. Using such water hammer testing, the effect of dynamic pressure was studied as a function of the magnitude of pressure during the electronic timing countdown. Data obtained indicate there is no significant impact in the timing of the electronic detonators in contrast to what has been reported in non-electric detonators.CITATION:Teowee, G, Solis, H, Papillon, B E and Ibarra, R, 2015. Effect of dynamic pressure on electronic detonator timing, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 575–578 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By P Brown, M Nagarajan, A Green, P Dare-Bryan

Coal loss is an important issue at many coalmines, with losses of five per cent being common. The type of loss varies from mine to mine but is dependent on mine strata, the drilling and blasting processes applied and the mining method used. Typical coal loss mechanisms from the drill and blast process are coal roof damage and edge loss. Usually a reduction in coal loss is in direct competition with the need to provide material that is well-fragmented and a muck pile that has the required cast percentage. These competing issues were addressed over a two-year period at a mine in the New South Wales Coalfields by implementing a five-step approach. This was centred around building an understanding of the coal loss mechanisms utilising proprietary heave- modelling software, measuring coal losses by comparing survey to drill and/or gamma logs and implementing appropriate coal loss reduction processes. The end result exceeded expectations with a 95 per cent reduction in coal loss. Mine excavation productivity was maintained and coal loss minimised to less than one per cent of the in situ coal block.CITATION:Nagarajan, M, Green, A, Brown, P and Dare-Bryan, P, 2015. Managing coal loss using blast models and field measurement, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 429–436 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By H Parra, D Zenteno

Fragmentation modelling has been in use in the mining industry for a long time; however, there are still some aspects to tackle with regard to its use for strategic/planning and day-to-day purposes.On one hand, an important amount of resources are allocated to the task of calibrating and validating a good fragmentation model. Nonetheless, errors during the implementation stage introduce uncertainty into the prediction.On the other hand, it is common practice in the mining industry to use only discrete values to represent the fragmentation from blasting (k20, k50, k80), which provides a biased interpretation of the situation as, for instance, the best and worst possible cases are not taken into account. This is particularly critical when a continuous improvement philosophy has been adopted and modelling is used to either modify the drilling and blasting designs or plan ahead.It is well known that every site has particular conditions (rock mass, equipment, drilling and loading practices, among others) that often define unique trends in implementation. These trends can be captured using statistic and probabilistic techniques and then used as proxies for further analysis.This paper explores the potential of including implementation data in the form of probabilistic distributions into the Swebrec model to improve the performance of this engineering tool during the decision-making process.The fragmentation results of four designs were modelled using three different degrees of accuracy in the implementation for the burden, spacing and explosive column length.The data analysis showed that the probabilistic approach helps to achieve a broader perspective regarding the fragmentation that it is possible to obtain and the implications for the subsequent processes. The analysis also showed that the likelihood of producing similar fragmentation with different designs (involving different powder factors and costs associated) increases with the variability of the implementation.CITATION:Parra, H and Zenteno, D, 2015. Evaluating the inclusion of the implementation variability into fragmentation modelling, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 121–126 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By J Seccatore, T Marin, M Cardu, G De Tomi, F Galvão, A Rezende, E Melo

Small-scale mining operations are characterised by a large variety of equipment availability and a high level of operational flexibility. Mine planning is usually scarce or absent in small quarries in Brazil, and mine management generally focuses on daily operations. As a result, analysis of the effects of unit operations, such as blasting, over the whole mining process is often neglected. The goal of the following project was to study the effect of production blasting on loading and hauling times, secondary breaking times and primary crushing times at the Experimental Mine of the Research Center for Responsible Mining of the University of São Paulo, Brazil. The operations analysed included blasts that performed:under the average operational standard, defined in this paper as Case 1according to quarry standards, defined in this paper as Case 2.In order to establish the effects of blasting on the downstream process, three key performance indictors were used:The time taken to load the truck, when there is the need for material selection. Due to the fact that we do not have an operational baseline, the increase in time cannot be established, meaning that we must content ourselves with comparing the mean time in each scenario.The average time used for secondary breaking machinery.The time required for the primary crusher to fully process the load of a single truck. The results obtained indicate correlations between the coarseness of the blasted material and these operational times. Solutions are suggested and evaluated for the improvement of the small-scale mining process.CITATION:Marin, T, Melo, E, Seccatore, J, Cardu, M, Galvão, F, Rezende, A, Bettencourt, J and De Tomi, G, 2015. The effect of drilling and blasting performance on fragmentation in a quarry and time for loading, secondary breakage and crushing, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 355–362 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By S Thomson, G Rigby, J Norgard, D Wilkinson

Bulk explosives provide the energy to move a rock mass and reduce it to an optimal size (fragmentation). The intensity of energy needed depends on several factors including a customer’s geology and end objectives. An energy mapping tool has been developed to help customers to determine their bulk explosive needs based on these objectives.At one end of the energy map dealing with high-energy products, a new range of bulk explosives products for surface mining have been developed. With these products, it is possible to provide blast designs with up to nearly triple the relative bulk strength (RBS) of ANFO, and address primary focus areas for mining operations, including the reduction of drill and blast costs, improvements in production rates, better face advance through improved broken stock management, better drill productivity, improved milling efficiency and lower energy costs in surface mines.In this paper, field trial results from the first level of new high-energy products are presented. These products have an RBS 2.25 times that of ANFO. Industry variations of a smaller diameter (89 mm) pumped product for civil quarrying applications, and for large diameter (311 mm) hard-rock metalliferous mines are presented. For both cases, the run-of-mine fragmentation levels obtained with the new bulk explosives are contrasted with the fragmentation profile generated with the currently accepted product range applied in similar geological conditions. The new products show increased fragmentation across the measured size distribution, with reduction in P50 values of 20 and 37 per cent over the currently used product for the 311 mm and 89 mm diameter blastholes respectively.CITATION:Wilkinson, D, Rigby, G, Norgard, J and Thomson, S, 2015. Higher energy bulk explosives – matching products to rock types using an energy map concept, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 579–584 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By M Araos, I Onederra

A novel explosive formulation that substitutes the use of ammonium nitrate (AN) with hydrogen peroxide (HP) as the main oxidising agent has been developed and tested as part of an Australian Coal Industry Research Program (ACARP) project. The main objective was to provide a step-change solution that has the potential to completely eliminate NOx fumes in blasting. The development of this HP/fuel-based explosive started with a comprehensive detonation characterisation program, consisting of unconfined velocity of detonation (VOD) measurements of samples at different diameters, densities and void sensitisation techniques. VOD results showed that the HP/fuel-based explosive mixtures behaved similarly to non-ideal commercial explosives; in that way mixtures could be tailored to achieve specific detonation performance targets. The next stage of testing in this development involved preliminary confined tests to evaluate the rock breakage potential of the HP/fuel-based explosive mixtures. Fully instrumented single-hole tests were conducted in a limestone quarry. Results from these preliminary trials confirmed the rock breakage performance of HP/fuel-based explosive mixtures. The confined VOD measured in one of the tests was 5100 m/s in a 102 mm diameter blasthole at a density of 0.96 g/ml. The corresponding borehole pressure measurement of this HP charge was 2.61 GPa with a detonation temperature of 2921°C. Based on near-field accelerations, both HP and ANFO charges displayed similar attenuation characteristics in the test conditions. Post-blast observations indicated that the breakage performance of the HP mixtures clearly reflected the in-hole detonation performance measurements obtained, confirming the ability of these explosive mixtures to both fragment and effectively displace the rock mass under evaluation. Further research work continues with the future commissioning of a prototype mixing and delivery unit, the successful completion and analysis of data from multiple-hole trials, and further characterisation work associated with product stability, reliability and performance under different geotechnical conditions.CITATION:Onederra, I and Araos, M, 2015. Detonation and breakage performance of a hydrogen peroxide-based explosive formulation, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 565–574 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By D Symonds, S S. Kanchibotla, L Kennelly, G McNamara, J Gaunt, B Adiyansyah

Ban Houayxai is a gold-silver mine operated by Phu Bia Mining Limited in Laos since 2012. The first two years of operation processed predominately soft oxidised ore but subsequent years were expected to process more fresh hard ore. Fragmentation of the fresh primary ores was also expected to be much coarser than for the soft oxide ores. This coarser and harder ore is expected to significantly reduce mill throughput and mining productivity. The Ban Houayxai management realised the potential downside risk when processing fresh harder ores and implemented a blast optimisation project to deliver finer fresh ore to the mill without unduly increasing blast induced dilution and damage.JKTech and the Ban Houayxai drill and blast team began a joint blast optimisation project in April 2013 to achieve finer fragmentation from fresh ores. This was achieved by modifying the bench geometry, blast patterns and applying exceptionally high levels of quality control during implementation. Blast induced ore loss and dilution was controlled by adjusting the ore blocks for blast movement. Finer fragmentation from these modified designs improved mill throughput for the hard fresh ore by 46 per cent above design on average. These new practices have been embedded in site operating procedures and have provided a quick reference ‘cookbook’ document for the engineers.CITATION:Gaunt, J, Symonds, D, McNamara, G, Adiyansyah, B, Kennelly, L, Sellers, E J and Kanchibotla, S S, 2015. Optimisation of drill and blast for mill throughput improvement at Ban Houayxai Mine, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 307–314 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By D Martin

The Rio Tinto (Mount Bruce Mining Pty Ltd) Koodaideri Iron Ore Project is located approximately 110 km north-west of Newman in the Pilbara region of Western Australia. During detailed ecological studies of the project area, a significant maternity roost (containing around 430 individuals) of the Orange Leaf-nosed Bat (OLNB) (Rhinonicteris aurantius) was discovered within the boundaries of the proposed mining area. The OLNB is listed as Vulnerable under the Commonwealth Environment Protection and Biodiversity Conservation Act 1999 and is listed as a Schedule 1 species under the Western Australian Wildlife Conservation Act 1950.With a good understanding of blast vibration attenuation in the Pilbara’s different geologies and in the absence of other known studies, it was considered that appropriate buffer distances between mining and bat colonies were not scientifically determined. Therefore, to inform the environmental approvals process that was underway, a series of seismic blasts was planned to assess and measure the sensitivity of the OLNB to trial-sized seismic blasting activities to develop a more scientifically based buffer zone for the protection of the OLNB. This was to be achieved by testing ground attenuation of the site and measuring any response from the OLNB to the firing of seismic charges. Rio Tinto sought the independent expertise of ecological consultants to evaluate and participate in the work to quantify the level of sensitivity of the bat colony and to outline the proposal to government authorities.After detailed risk assessment and project mapping, the seismic blasts were implemented, with the aim of firing individual charged and measured vector peak particle velocity (VPPV) at the OLNB roost cave, combined with monitoring OLNB disturbance activity within the roost that was invoked by the blasts. A series of six charges were fired with the VPPV ranging from 0.66 mms-1 to 18.70 mms-1. The OLNB activity was monitored using high frequency microphones, which detect bat calls emitted during flight. Under daytime conditions, the bats would normally be dormant, so the null hypothesis was for no calls to be detected if the bats displayed no disturbance behaviour. This work has improved understanding of mining activities (blasting) on the OLNB species, assisting in establishing mining exclusion zones that are based on scientific data, contributing to a sustainable future for both the environment and the mining industry.CITATION:Martin, D, 2015. Scientific evaluation of fauna sensitivity to blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 519–526 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By M Jahani, M Taji

For suitable production planning in an open pit mine, and also to carry out the optimisation process during the mining production cycle, prediction of fragment size distribution is required prior to carrying out the blasting operation. For this purpose, many prediction models, such as empirical models, were presented. The proficiency of these models differs in various conditions and mines. Therefore, in this paper the most important models, including SveDeFo, Kuz-Ram, CZM, Modified Kuz-Ram in 2005, Kuznestsov-Cunningham-Ouchterlony (KCO) and also Gheibie et al, were examined by the information of 20 blasts in Gol-Gohar iron ore mine. Fourteen images were taken on average for each blast. For image processing analysis Split-Desktop software was used. After examination, it was understood that none of the available empirical fragmentation models had presented acceptable performance, except the Kuz-Ram model for magnetite ore, which had somewhat acceptable results. However, this model for blasting patterns in hematite presented unsuitable results. Examination and comparison of two important distribution functions, Rosin-Rammler and Swebrec, were carried out and it was observed that the performance of Swebrec for fines was far better than Rosin-Rammler. This result for the upper part of fragment size distribution curve, coarse, is the reverse.CITATION:Jahani, M and Taji, M, 2015. Comparison of empirical fragmentation models at the Gol-Gohar iron ore mine, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 707–714 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By R Castedo, P Segarra, I del Castillo, L M. López, J A. Sanchidrián

This work investigates some suggested methods for blast vibration monitoring on a hard surface based on 53 tests on a vibration exciter. Errors in the measurement attributable to coupling have been described as function of frequency by the rock-to-mount (or coupling) transmissibility, ie ratio of the velocity of the vibration sensor mount to the velocity of the rock motion. Transmissibility has been measured from 2 to 200 Hz, at two vibration levels (5 and 20 mm/s), in four seismographs. Attachment methods with an anchor, thermal adhesive and gypsum plaster allow stiff rock-to-mount coupling. They ensure accurate measurements (errors below 0.3 dB) for frequencies commonly found in blasting (below 100 Hz) irrespective of the mount characteristics and the vibration level. Free laid mounts and sandbagged vibration sensors lead generally to a poor, weak coupling. Errors are non-linear errors with the input velocity, ie the operating frequency window narrows as the velocity of the ground increases. Free mounts follow ground motion acceptably well (error up to 0.4 dB) at both vibration levels and frequencies below 15 Hz. At higher frequencies, free mounts lead to the largest distortions with expected errors ranging from 0.8 to 6.6 dB. Sandbagging limits the expected errors below 1.3 dB, but it does not prevent large errors that can be up to 4.5 dB. Both frequency and velocity should be considered together to assess the measurement errors instead of the expected accelerations, as it is currently made.CITATION:Segarra, P, Sanchidrián, J A, Castedo, R, López, L M and del Castillo, I, 2015. Effect of vibration sensor mounting method on the quality of vibration measurements, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 545–552 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By D P. Blair

There are two major aspects to wall control blasting – the potential for any blasthole to cause wall damage and the potential for a delayed sequence of blastholes to cause damage. The damage potential of individual blastholes is governed by standoff distance and charge weight. However, for locations sufficiently close to a highwall, dynamic finite element models and field measurements show that there is also a critical nature to those blastholes very close to the wall, over and above standoff distance. At many mine sites, the charge weight/standoff-distance is set by trial and error. Thus, a significant aspect of the present work is the determination of dynamic stress radiating from a blasthole. Unfortunately, the modelling and measurement of this dynamic stress is still faced with many difficulties. Typical models have questionable aspects, which casts serious doubt over their predictions, and it is shown that the Hustrulid Bar experimental technique does not correctly account for stress wave attenuation in extended media. In an attempt to solve the dynamic stress problem, the present work describes a model based on an exact solution under the assumption of viscoelastic material. The model takes full account of the rock mass elastic/viscoelastic properties, the explosive type, geometry and primer location and predicts a dynamic stress for direct comparison with the unconfined compressive strength of the local rock mass. This model predicts the standoff distance required to avoid damage due to a single blasthole. The behaviour of a delayed sequence of blastholes is analysed using an upgraded waveform superposition model, covering a range of initiation delay combinations, which predicts the peak particle motion (PPM) induced in the wall for each combination. This approach shows that there is no need to fire dedicated trim shots close to walls; all that is required is a carefully modified production shot. The mechanism of vibration screening is discussed, and its use in a superposition model highlights the potential of reverse firing (shield blasting) to reduce wall PPM. A conceptual model is also introduced to give a further insight to vibration screening and damage (via ground heave). This model predicts that a centre-lift blast will have a central heave profile and that a reverse-fired shot will produce a smaller power trough than that produced by a standard shot. It is demonstrated that the mechanism of presplit formation is not well understood; nevertheless, experimental evidence shows that presplits can be an effective method for reducing wall vibrations.CITATION:Blair, D P, 2015. Wall control blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 13–26 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By P Moser, R Ivanova, F Ouchterlony

This paper describes model-scale bench blasts on mortar blocks with distorted drill hole patterns, done in 2013–2014 at the Montanuniversitaet Leoben. The main aim of the project is to see if the fragmentation from and the crack development behind blasts with and without drill hole deviations differ significantly.The dimensions of the test blocks were 660 × 280 × 210 mm (L × W × H). They were mounted inside a yoke that allows the blast waves to escape (see Figure 1). Three rows in each block were shot row by row with a nominal pattern of B × S = 70 × 95 mm. The same nominal delay 73 µs (ie 1 ms per m burden) between holes was used throughout. Blocks with holes of stochastic collar position errors (variations in burden or in burden and spacing but constant row volume) and systematically shifted collar positions (blasts with staggered pattern) were shot. The results were compared to reference blocks without collar deviations.Apart from the sieving analysis, the remaining bench faces were measured with a stereo-photogrammetric method and horizontal roughness profiles for each row were constructed. Sawing slabs from block remains after the third row and use of dye penetrant allowed the study of internal blast damage.The analysis showed that none of the changes in borehole collaring had a significant effect on the sieving curve (median). The sieving results confirm earlier findings though that the fragmentation gets finer with the number of rows shot, implying that blast damage from earlier rows has an influence on the blasting results. The tests demonstrated that the nequiv (equivalent n-value) has increased ten per cent by shooting staggered pattern and decreased by seven per cent by pattern with burden and spacing errors. For the rest of the patterns, the nequiv was roughly the same.The surface roughness investigation showed that a smooth surface was achieved by the staggered pattern. The other deviations patterns did not show a clear trend.The internal blast damage, which was measured in the remaining part of blocks, showed that out of eleven, four crack families seemed to be most affected by blasting. The comparison of the reference and distorted patterns showed that less cracks were apparent for the staggered pattern, ie less damage was introduced.CITATION:Ivanova, R, Ouchterlony, F and Moser, P, 2015. Influence of distorted blasthole patterns on fragmentation as well as roughness of, and blast damage behind, remaining bench face in model-scale blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 693–706 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By R Battison, R Duggan, S Esen, K Henley, P Dare-Bryan

Increased catch bench crest loss has been observed in recent years at Barrick’s Cowal Gold Mine situated in central New South Wales, Australia. A project was initiated to diagnose the cause of the crest loss, and evaluate ways to limit its effect on final walls.A range of different blast measurement techniques were utilised to evaluate the progressive damage caused to catch berms by presplit, production and trim blasts. Techniques employed included; single point vibration measurement, cross-hole seismic analysis, precision berm surveys, horizontal p-wave velocity measurements, crest loss volume calculation and water level changes between blasts.Blast measurements showed that the majority of damage to the catch berm was caused by the presplit blasts, which registered vibrations greater than 700 mm/s at 5 m behind the presplit line. As a result, considerable changes were made to the blast designs after a series of computer simulations via mechanistic blast modelling (MBM). The uncharged presplit collar was increased from 2 m to 4 m, and every second hole was left uncharged. Vibration modelling using a multiple seed wave (MSW) model was used to optimise trim blast delay timing. Burden relief was changed from 16 ms/m to 27 ms/m using one hole firing per 4 ms time window, and the initiation angle was changed from shallow to steep. These changes in the presplit loading and trim timing helped reduce catch bench crest loss by 1–2 m.Trim shots using a high strength bulk emulsion explosive were also identified as contributors to berm damage after analysis of blast monitoring and MBM modelling. The modelling study resulted in the generation of alternative blast designs to minimise the crest loss, including the use of low-density/low-velocity of detonation (VOD) bulk explosive product (Flexigel™ Advantage) in trim pattern designs. This was trialled on the Northern and Eastern pit walls to evaluate the damage to catch berms on final walls. The trials demonstrated that berm vibration was reduced significantly; fragmentation was similar (or slightly blockier) compared to the fragmentation using the old blast designs; displacement of the berm was reduced, so increased catch bench widths were attained. This paper summarises the trials, and presents a summary of the crest loss to date.CITATION:Battison, R, Esen, S, Duggan, R, Henley, K and Dare-Bryan, P, 2015. Reducing crest loss at Barrick Cowal Gold Mine, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 189–202 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By B Mohanty, D Zwaan

Systematic near-field vibration monitoring of stope blasts was carried out in a large, deep underground mine. A total of 31 production blasts were studied in order to investigate the effectiveness of existing blast designs. This involved the vertical retreat mining method, which requires drilling a raise bore or blasting a slot raise (typically 1.22 m in diameter) using large diameter boreholes (165 mm). The diagnostic technique employed multistation near-field monitoring of blasts with high-g (100 g) and high-frequency (>10 kHz) triaxial accelerometers. The amplitude of the vibrations is correlated with the strain energy transmitted from each explosive deck. The results showed that more than 30 per cent of the explosive decks contributed little energy to the rock breakage process in these blasts, and an equal number contributed only inadequately. These findings are indicative of serious blast malfunctions. The problems can be traced to inadequate deck blast design and possibly to drill hole deviation. The various causes for such malfunctions are discussed and remedial measures suggested.CITATION:Mohanty, B and Zwaan, D, 2015. Assessment of underground production blast designs and blasting performance, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 607–616 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By I C. Carrasco, V G. Mirada, J F. D Domingo, F S. Leite

This paper investigates ore loss and dilution produced by rock movement in bench blasting. A total of four blasts, in which electronic detonators have been used, were monitored in Cobre Las Cruces Open Pit Mine (FQM Ltd) in Gerena (Sevilla, Spain). Rock motion has been obtained in 137 points of the free face and 6 points inside the block. Multiple liner regression has been applied to predict rock motion and estimate ore dilution as a function of hole coordinates, rock contacts, powder factor/hole, amount of explosive per blasthole, burden, spacing, hole length, stemming length, explosive energy, hole row, subdrilling, blast sequence, stiffness ratio, blasthole distance to free face, rock density and Young’s modulus. The model is statistically significant with a determination coefficient over 0.8. Rock motion measurements in 31 more points have been used to validate the model and to show a reduction in ore dilution.CITATION:Domingo, J F D, Leite, F S, Mirada, V G and Carrasco, I C, 2015. Dilution, ore grade and blast movement calculation model, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 71–78 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By A Karrech, E Hamdi

The uncertainty of geomaterials properties is commonly encountered in resource engineering applications, especially in mining engineering where the rock mass texture, joints, fractures and damage zones can impose the mining method and operation cycles. In the present research work, we focus on the elastic properties of rock masses. We use stochastic numerical simulation of fractured rock masses to estimate their Young moduli. The procedure starts with field mapping campaigns which are conducted to evaluate the locations, dip angles, strike and trace lengths of pre-existing fractures. We develop statistical law parameters of the natural fracture network to represent the weakness patterns. In addition, we use HLA-Dissim, a recently developed and validated Matlab program, to simulate the propagation of monochromatic longitudinal waves and derive the equivalent elastic modulus of fractured rock masses. Such procedure applies within a simulation domain, which is greater than an Elementary Representative Volume.At a second stage, we conduct finite element simulations to validate the previous approach. The matrix and the actual fractures zones are reproduced in the model to mimic the natural set-up. The block is excited on particular positions and its response is evaluated on predefined spots. Real field rock fracture mapping data and monitored single-hole blast induced vibrations are used to validate the theoretical and numerical approaches discussed herein. Comparison between the simulated and measured vibration records shows a great agreement which confirms that the proposed methodology has a full potential to predict and optimise multihole/multidelay blast-induced vibrations.CITATION:Hamdi, E and Karrech, A, 2015. A methodology for rock mass characterisation to control blast-induced vibrations, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 89–96 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By N Johansson, D Johansson, A Beyglou, H Schunnesson

As demand for optimisation of mining processes increases, more attention is drawn to blast performance and fragmentation improvement. Fractures and discontinuities are among the most influential factors in blast results, therefore one of the initial steps towards blast optimisation is to gather information about the rock mass and integrate it in blast design. This paper presents a method for assessment of rock mass discontinuities and integrating it in production blasts in the Aitik open pit copper mine in Sweden.3D photogrammetric techniques were utilised to map discontinuities and distinguish domains of similar geologic structures in the pit. As a pilot study for a future campaign, four different initiation directions were tested through six pilot blasts in one of the domains. The results were compared in terms of swell and loading efficiency of rope shovels to identify the correlation between blast performance and initiation direction compared to major discontinuity families.It was established that in the trial domain, blasts initiated towards north or north-west yielded larger swell and better performance of loading. Comparing these blasts with discontinuity families show that there is a correlation between blast performance and initiation direction according to the dip and strike of these discontinuities. Such knowledge can be used for future blasts in the same domain to increase long-term operational efficiency through slight modifications in drill pattern and initiation design.CITATION:Beyglou, A, Schunnesson, H, Johansson, D and Johansson, N, 2015. Adjusting initiation direction to domains of rock mass discontinuities in Aitik open pit mine, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 385–392 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By M J. Thurley, M Wimmer

To assess the present-day functionality of large-scale sublevel caving at LKAB Kiruna a comprehensive measurement program was undertaken involving blast function, fragmentation and gravity flow. As part of this assessment, a fragmentation measurement trial was performed based on 3D imaging of the drawpoint and corresponding bucket load of the underground load-haul-dump (LHD) excavator. 3D image data from stereo photogrammetry was collected and an automated image analysis strategy developed. A number of data sets were collected for each of the drawpoint and LHD bucket, along with sieving results for four of the LHD bucket loads (totally about 70 t). Two of the sieving results were used to inform the automated image analysis strategy, and two were held back as a comparison. Large variations in the visible particles are apparent when comparing corresponding drawpoints and LHD buckets highlighting the impact of sampling location and the need to measure large quantities of data in order to avoid bias from small samples. The results show that 3D imaging and analysis can produce fully automated measurement and analysis of the visible particle size distribution. Although this is not the same as the sieve-size distribution it provides useful estimation of both the larger size classes and a bulk estimate of fine material below approximately 60 mm. The 3D stereo photogrammetry measurement system used produced very high 3D point density but this was achieved using a custom up-sampling technique which significantly smoothed the data, removing small particles, smoothing edges, and this negatively affected the particle delineation algorithms.CITATION:Thurley, M J, Wimmer, M and Nordqvist, A, 2015. Blast fragmentation measurement based on three-dimensional imaging in sublevel caving drawpoints and underground excavator buckets at LKAB Kiruna, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 763–774 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By R Yang

This paper presents a fragmentation model for large production blasts in an open pit or underground environment. The paper shows that the particle velocity is directly related to pressure, strain, and strain rate and so it can be considered as driving force and mechanism of rock fragmentation. This is supported by the fact that a vibration with a larger peak particle velocity (PPV) generates larger disturbance in rock and so finer fragmentation or more blast damage than a low PPV. The crack distribution in rock from impact is based on findings from previous researchers (Seaman, Curran and Shockey, 1976; Liu and Xu, in press). The fragmentation size is calculated at three-dimensional grid points within a blast. The fines and oversized blocks are calculated explicitly – the fines generated close to blastholes and big blocks far from boreholes are modelled naturally. The multiple blasthole fragmentation (MBF) model takes surveyed irregular geometry of the free face of a blast as the calculation boundary. The MBF can model fragmentation with over one million grid points. Examples of the model’s field comparison are also included.The PPV at a calculation grid is estimated based on the same approach used for the near field non-linear vibration model (Yang and Scovira, 2007). The method is based on the dominant charge for a calculation grid point, non-linear charge weight superposition within a charge and from multiple charges, strain wave broadening, and amplitude attenuation with distance from a charge segment. The blasthole confinement affected by earlier firing charges is also taken into account.The MBF model inputs from blast design, such as: location and orientation of each blasthole, stemming length, blasthole diameter, multiple decking, bench height, initiation sequence, etc. It models the effect of the delay and its scatter in each blasthole on fragmentation and has a statistical modelling capability for geological random variation on attenuation of particle velocity wave. The wave reinforcement due to instantaneous waves arriving or diminishing cooperative contribution due to long delay intervals between charges is also simulated.The results are displayed in 3D volumetric plots, contour of fragmentation in cross-sections, and size passing curves for a whole blast or a region of the blast.CITATION:Yang, R, 2015. A multiple blasthole fragmentation model – its concept, formulation, capability and field comparison examples, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 177–186 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By B Green

With a focus on safe productive tonnes, there has been an ongoing drive to increase the productivity of the mining fleet across BHP Billiton. In response, a team from the Iron Ore business was formed to review all aspects of the end-to-end drill and blast process and to challenge conventional practices that limit production efficiency. As a result of the outcomes of this work, a number of initiatives were identified to improve operational practices that have also delivered significant cost savings.One such initiative was to increase pattern size to a minimum of 1 Mt where practicable, thereby creating ‘megablast’ as a new standard across all mines. To achieve blasts of this size, the team had to overcome the complex problem of integrating wall control into the megablasts.With traditional blasting techniques, the key strategy, which is also historically inefficient but was thought to be integral to having stable, safe walls, was to utilise the trim blasting/modified production blasts technique (ie narrow blasts along the pit wall designed to ‘peel off’ the material while minimising the effects of vibration and charge confinement on wall integrity).Small traditional trim patterns comprise three to four rows of production holes and one or two rows of batter/buffer holes of reduced diameter that require the firing face to be completely exposed before blasting. This is an extremely slow process that requires a lot of resources for very little tonnage while adding additional expense to the final cost per tonne.This paper will show how the megablast approach was developed to control damaging vibration and confinement effects, flyrock and fragmentation while having the largest possible blast that includes wall control. The new practice is based on a theory that involves the initiation point and control row being the second row of holes from the pit wall itself. Adjusted charges in vented batter and buffer holes help to achieve an optimal toe design, and at the same time create a zone of broken ground that absorbs damaging vibrations formed by the attached production blast of any size, whether it is a straight wall or a multi-angled complex pit shell design.Using the new style of blasting has allowed an increase in the size of the patterns from an average of 300 kt to over 1 Mt whilst maintaining pit wall integrity. Case studies will be presented showing drill, charge and tie-in designs with the presentation having additional blast videos, including overall shots of blasts and in-close footage of what happens behind the blast at the crest of the planned catchment berm.The paper will also demonstrate the flow-on effect of using this style of blasting to reduce operational costs associated with other downstream processes, such as the reduced requirements for pattern preparation, an increase in productive digging, reduced maintenance costs and a decrease in fuel burn for equipment.CITATION:Green, B, 2015. Megablasts – enabling technologies in BHP Billiton Iron Ore, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 599–606 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015