Search Documents

By S Mitra, B J. Monaghan, T Honeyands, G Evans, R Chowdhury, D Scimone

Due to the harsh operating conditions, wearing of the inner refractory lining in a Basic Oxygen Steelmaking (BOS) furnace reduces the useful life of the refractories and incurs a significant cost component for relining. In this study, firstly, a combined compressible and incompressible computational fluid dynamics (CFD) model was developed to identify the potential wear prone zones in an industrial scale BOS system during the supersonic oxygen blowing phase by quantifying the wall shear stress distributions. Next, the retained slag splashing process was simulated by introducing an inert gas to residual slag mass to achieve a protective coating on the refractory walls. Effect of both design and operational parameters such as lance head configuration, lance position and the initial slag volume on the slag wall coating performance were quantified and most favourable conditions were determined.

Jun 19, 2024

By K Nakashima, K Aya, T Sumita, N Saito

Electro slag remelting (ESR) is one of the methods used to produce high-cleanliness steel. In the ESR method, the product steel electrode is immersed in flux, and the electrode is melted by the Joule heat of the flux generated by high current. CaF2-based melts are mainly used as fluxes, but the electrical conductivity of CaF2-based melts varies widely among researchers and measurement methods. Therefore, this experiment aims to measure the electrical conductivity of CaF2-based melts based on the van der Pauw-Ohta method, which does not require the cell constant that is a fundamental error factor in electrical conductivity measurement at high temperatures. The measurement temperature was set at 1450–1600°C, and dehydrated Ar flowed through the furnace at 200 mL/min. Electrodes were fabricated by Pt-30mass per cent Rh alloy, and the electrodes were connected to an impedance analyser using a four-terminal probe. The electrodes were immersed in the melt, and the impedance and phase angle were measured by AC frequency sweep (50 Hz to 200 kHz). The electrical conductivity was then calculated by utilising the impedance’s real part values when the impedance’s imaginary component was zero. The electrical conductivity showed a positive temperature dependence. The electrical conductivity of 60(CaO⋅Al2O3)-40CaF2 melt increased with increasing temperature but was found to be roughly one-third of those of the previous studies. In the conductivity measurement of 60(CaO⋅Al2O3)-40CaF2 melt, the AC frequency with a phase angle of 0° was found to be different depending on the temperature and immersion depth. By sweeping the frequency, the impedance at the phase angle of 0° can be obtained, which enables us to measure the electrical conductivity more accurately.

Jun 19, 2024

By D Felipe, G J. Harbort

In the past 40 years substantial changes have occurred in flotation machines. This has included increases in mechanical cell size to 630 m3 , significant changes to flotation column aeration design and widespread use of the Jameson cell and other pneumatic flotation cells. Over the corresponding period there has been increased used of machine characterisation measurements to benchmark and optimise flotation circuit performance. JKTech maintains a database of industrial flotation machine characterisation measurements. The database contains over 4000 entries and includes gas dispersion measurements, such as bubble size, gas hold-up and superficial gas velocity, cell dimensions and impeller tip speeds. Data comes from numerous operating sites and commodity groups, including gold, copper, molybdenum, nickel, palladium, lead-zinc, platinum, silica, phosphate, coal and iron ore. Flotation duties registered include flash flotation, preflotation, roughing, scavenging and cleaner circuits. Measurements have been conducted on a wide range of flotation machines from different manufacturers. This includes forced air machines, such as Outotec and Dorr Oliver, and self-aerated machines, such as Denver and Wemco. The database also includes substantial flotation column entries, such as the Microcel, Eriez/CMT Slamjet and Jameson cell. This paper describes the flotation machine characterisation database and discusses the variation between different types of industrial flotation machines, in operating production circuits.

Aug 24, 2022

By Y Cui, G Cao, H Zong, J Zheng, J Wang, S Yue, J Zhao, B Li

The iron (Fe) concentration in nickel slag is high, making its recovery and utilisation a hot and challenging topic. In the nickel smelting process, using CaO instead of SiO2 to adjust slag’s composition, and then directly reducing Fe from the output of molten slag is a more feasible method in practice for Fe recovery in nickel slag. The adjustment of slag’s composition in the nickel smelting process will have an impact on the distribution of impurity elements such as Pb, Zn, and As. In this paper, the slag adjustment of nickel smelting process was carried out with the oxygen-enriched topblowing system. The distribution of impurity elements in the smelting products with each composition slag was conducted by using thermodynamic software. Experimental verification was performed with rich oxygen top-blowing, and the distribution characteristics of impurity elements in the smelting products were characterised to explore the differences in mineral phases of impurity elements with each smelting conditions, elucidating the distribution patterns of Pb, Zn, and As in each phase. The results indicate that after slag adjustment, impurity elements are more easily to volatilisation and removal into the gas, reducing their total concentration in slag and matte. In the slag, the existence form of Pb, Zn is changed from silicate to ferrate, and As is changed from arsenate to low-valent arsenic oxide. It is easier to decompose the impurity-containing mineral phase and remove the impurity elements in the subsequent iron extraction process.

Jun 19, 2024

By J Safarian, M K. Kar

Bauxite residue is one of the most important by-products from the alumina industry with no commercial use till now. The utilisation of bauxite residue through pelletising with different lime additions, hydrogen reduction, and smelting has been studied in this work. Three different types of green pellets were made with varying calcite-to-bauxite residue ratio and subsequently sintered at elevated temperatures. The sintered pellets were isothermally reduced at 1000°C under hydrogen gas followed by smelting of the reduced pellets in argon at 1500°C. Smelting of the reduced pellets leads to the recovery of metallic iron and the formation of a leachable calcium aluminate slag. X-ray diffraction (XRD) and scanning electron microscope (SEM) were used to characterise the phases and microstructural analysis. The iron produced in the smelting process has a high purity, above 99.5 wt per cent. While the iron content of the slags is quite low, and the slags shows variations of krotite (CaAl2O4), gehlenite (Ca2Al2SiO7), and perovskite (CaTiO3) phases based on the variation of calcite addition. It was found that the more calcite addition in pelletising yields higher percentage of krotite phase as compared to lower calcite-containing pellets. Employing quantitative XRD analysis, the krotite phase fraction was found approximately 85 wt per cent for higher calcite-added pellet, and around 74 wt per cent for lower calcite-added pellet. FactSage™, ver 8.1 (Thermfact and GGTTechnologies) thermodynamic software was used to evaluate the obtained experimental data, they both revealed that the

Jun 19, 2024

By A Suwandhi, H Utama

PT. Indo Muro Kencana (PT.IMK) is a gold mine that is located in Central Kalimantan, Indonesia. Drilling and blasting activity is applied in order to support mining production. Drilling and Blasting (D&B) planning is conducted by its engineers. A drilling and blasting contractor conducts drilling and blasting activity. The objective of this paper is to evaluate the implementation of the scaled depth of burial (Chiappetta and Treleven, 1997) in explosive charging sheet application to increase blast efficiency. The function of the scaled depth of burial is to maintain stemming height above explosive charge in order to prevent the ‘over energy’ condition, to reduce the excessive fly rock possibility, to maintain rock fragmentation (digger’s productivity) and to increase blast efficiency. The focus of this paper is to implement the scaled depth of burial as a reference in D&B planning and practice, especially in designing stemming height. The purpose of this paper is to validate that the scaled depth of burial can be used as an engineering tool in D&B practice in PT.IMK. However, scaled depth of burial cannot applied as an engineering tool to determine stemming height above explosive charge for trim blastholes and secondary blasting area. In general, the implementation of the scaled depth of burial in PT.IMK is applicable for production blastholes (ore and waste blasting). In conclusion, it is clear that scaled depth of burial can be used as an engineering tool to create explosive charging sheet and also to increase blast efficiency (ore and waste blasting) in PT.IMK.

Jun 22, 2022

By K Haroon, J D. Speed, S P. Wood

Online analysis of continuous and batch processes has seen a dramatic increase in recent years, with examples ranging from petrochemicals to pharmaceuticals, to industrial biotechnology and food and drink. The particularly challenging environment of alumina processing has meant that instrumentation needs specific features and characteristics to be truly suitable, features such as: robustness, resistance to caustic conditions both in the analyte and the ambient environment, and reliability for long-term continuous use. Here we present the development of a novel FTIR spectrometer that achieves these requirements through the use of a static optics arrangement of mirrors, and stable diamond-tipped light-pipe probe. Firstly we give a very brief explanation of spectroscopic analysis, and the difference between FTIR and other infrared methodologies. Next we outline the novel arrangement of mirrors required to produce an interferogram without moving mirrors, and compare the benefits and drawbacks of this approach instead of conventional designs. We then share the results of laboratory analysis of synthetic Bayer liquors, with detection limits for aluminium hydroxide, sodium hydroxide, sodium carbonate and various sodium salts of organic acids. We then share the results of analysis on production samples, both in idealised laboratory conditions and then online in the process itself. Lastly we present work on in situ ultrasonic descaling solutions to avoid scale build-up and provide continuous cleaning of the probe – preventing the need for probe removal and manual cleaning.

Aug 24, 2022

By S Nkwanyana, I Govender

Batch experiments in a 0.6 m diameter mill have shown that improvements of about 13 per cent in the efficiency of energy utilisation can be realised in ball mills by replacing 25 per cent of the ball charge by an equivalent volume of cost-free critical size pebbles from AG/SAG mills. For a mill of a given size, speed and charge filling, the rate of size reduction of ore particles depends on (i) the frequency of grinding media collisions (ii) the probability of capture of ore particles between the colliding grinding media (iii) the probability of fracture of the captured particles. The probability of fracture depends on the magnitude of collision energy. The distribution of collision energy into shear and impact events determines the relative strengths of attrition breakage and impact breakage. The efficiency of energy utilisation depends on which of the two mechanisms of breakage is more desirable in a particular milling stage. In this paper collision data from a series of DEM simulations of a mill charged with steel media and a mixture of steel media and pebbles is presented in energy spectra and spatial distribution maps. The data provides the necessary detail to elucidate the improvements in the efficiency of energy utilisation in ball mills when using a mixture of pebbles and steel media.

Aug 24, 2022

By H F. Yu, S Ueda, J Diao, W F. Gu, Y Sasaki, H Qin

The main reason for the underutilisation of steelmaking slags is their instability, which is influenced by their complex phase structure. Recycling and sustainable steelmaking slag face challenges due to the presence of magnesium oxide (MgO), a crucial component in steelmaking slag. This study investigates the phase evolution of steelmaking slag during the cooling process with different MgO contents, using high-temperature experiments and FactSage™ software, ver 8.1, (by Thermfact/CRCT and GTT-Technologies) thermodynamic equilibrium calculations. X-ray diffraction (XRD) and scanning electron microscope - energy dispersive x-ray spectroscopy (SEM-EDS) analyses identified main phases in steelmaking slag, including Ca2SiO4 (C2S), RO (MgO-FeO solid solution), Ca2Fe2O5 (C2F), and Ca3SiO5 (C3S). The study reveals that RO phase increases as the MgO content increases. C3S precipitates from steelmaking slag with a 12 mass per cent MgO content at a reduced temperature of 1400°C. It is important to note that C3S remains in the steelmaking slag even after slow cooling. This may be due to the substitution of Ca2+ in C3S by Fe2+ and Mg2+ ions. Intriguingly, the precipitation of f-CaO in steelmaking slag with 10 mass per cent of MgO content occurred after one year, while there was no manifestation of f-CaO precipitation in the steelmaking slag with 12 mass per cent of MgO content even after one year. This discrepancy suggests a potential stabilising effect of an appropriate amount of MgO in steelmaking slag. However, it is crucial to emphasise that this inference lacks supporting data, necessitating further research to validate this hypothesis. The significance of this work is in uncovering the complexities of steelmaking slag behaviour, providing essential insights for optimising recycling processes. The research sheds light on the factors that influence the phase composition and stability of steelmaking slag, contributing to the utilisation of steelmaking slags, promoting environmental sustainability, and enhancing the overall efficiency of metallurgical processes in the current industrial landscape.

Jun 19, 2024

By R M. Yanamandra, M Kumar, S K. Tripathy, N Mangadoddy, P Sudikondala

Spiral concentrators are one of the flowing film gravity concentration devices used to beneficiate coal and mineral ores. The aim of the current study is to understand the particulate flow and separation performance of an LD9 spiral concentrator using a multi-phase Computational Fluid Dynamics (CFD) model. The CFD model utilises the Algebraic slip mixture model to simulate particulate flows. The model employs the Renormalisation group (RNG) k-ɛ turbulence models to resolve the fluid turbulence. Initially, the volume of fluid method was adopted to track the water-air interface. Simulations were then carried out at low (0.3 and 3 wt.%) and moderate (15 wt.%) solids concentrations. Multiple particle-phase representing particles of poly sizes (75–1400 µm) and multi-densities (1450–2650 kg/m3 ) were simulated to study the particle segregation on the spiral trough surface. The numerical predictions are compared with the literature performance data at a diluted pulp flow rate of 6 m3 /hr. The results were found in close agreement. Further, the same CFD model is used to study the change in pulp velocity, streamflow rates, and separation performance at increasing solids concentration. For the same density particles, Fine particles mostly show higher volume concentration in the middle and outer trough regions, whereas coarse particles show higher volume concentration in the interior and central trough regions. It implies that the fine particles mostly segregate towards the outer region, and dense particles segregate towards the axial column.

Aug 24, 2022

By B Tadesse, L G. Dyer, B Albijanic, M Jung

The presence of high concentrations of dissolved ions in groundwater, sea water or recycled water may alter the water structure, particle surface wettability and colloidal interactions between bubbles and particles and can have a significant effect on mineral flotation. While the impact of water quality on the flotation of precious and base metal minerals is well established, no relevant published study exists currently regarding the effect of water salinity on the flotation of rare earth bearing minerals. This paper attempts to quantify the effect of water quality variation on flotation recovery and grade of rare earth minerals and gain an understanding on which ions existing in saline water affect flotation behaviour. Specifically, it is aimed at investigating the effects of water quality on the flotation of monazite in the presence of cations such as Ca2+, Mg2+, K+, and Na+. Flotation tests, zeta potential measurements, and adsorption tests were performed to explain the flotation behaviour. It was found that monovalent ions such as Na+ and K+ have negative impact on rare earth minerals recovery and grade. The result of single mineral flotation tests showed that the floatability of monazite was significantly depressed in the presence of Ca2+ and Mg2+. The result of single mineral flotation test showed varying depression levels in the presence ions in the order of Ca2+ > Mg2+ > Na ~ K.

Aug 24, 2022

By J Harding, S Munro, R A. Bearman

Despite the importance of the primary crushing stage, performance optimisation is not well analysed with sufficient focus to give improvement opportunities. At the Newcrest owned Telfer operation, liner life plays an important part in scheduling planned maintenance. Major consideration is given to monitoring crusher performance, as the highly abrasive nature of the feed significantly impacts the liner wear life. A study was undertaken by the lead author which focused on establishing a strong baseline of accurate data pertaining to the performance of the crusher, in terms of, operating parameters, liner life and key machine design factors. As part of the study, mining feed materials were examined for a particular set of liners and this revealed that improved methods should be pursued. Due to the competitive nature of the mining industry, the business solution to complex problems with long shutdown cycles should be streamlined to incorporate a non-operational modelling approach that is significantly more efficient than traditional online trial and error methods. In order to dramatically reduce the time and business risks, it was decided to engage services to model and simulate the liner life by varying main operational and mechanical factors. The key to all simulation work is gathering high quality baseline data. Such data allowed deployment of the Kinematic Crusher Model and validation of the model against worn 2D wear liner profiles. The proven model was then successfully deployed to predict operational values that defined crusher performance. To enhance the study, further investigation into a set of mechanical and operational simulations generated a sensitivity matrix measuring key performance parameters throughout the wear life of the liners. The study revealed throughput as a highly sensitive parameter and a change in eccentric throw provided the greatest improvement in extending liner wear life.

Aug 24, 2022

By M S. Henderson, R D. Alorro, L G. Dyer

An alternative leaching system for rare earth element recovery from monazite is under development. The initial stage utilises oxalic acid to convert the rare earth phosphate into an oxalate salt through dissolution and reprecipitation and it is the efficiency of this stage that governs the overall recovery achieved. It has previously been proposed that lixiviant consumption is the primary limitation in this process. This work further investigates a range of conditions in an attempt to further elucidate the factors influencing the achievable conversion in this stage. It has been shown that the pH may be governed by multiple reactions both consuming and producing acid (thus the mild change over time). The importance of proper mixing and potential to operate at lower temperature with only moderate impact on kinetics has also been demonstrated. Staged/sequential leaching is more effective in fresh solution as opposed to restoring the lixiviant concentration with subsequent reagent addition, suggesting some impact of solution composition. However, contrary to previous findings, subjecting the leach residue to fresh solution resulted in significant decline in leach rate and overall dissolution. This may be because a greater proportion of conversion was achieved in stage 1 in this work than in previous investigation. This may indicate that eventual passivation or the presence of some more refractory REE minerals limits dissolution. Iron dissolution was relatively consistent upon exposure to fresh solution, displaying the ability of the solution to continue to leach the goethite component of the concentrate.

Aug 24, 2022

By S Khadhraoui, T Yusuf, C Kirmse, E Hecker, R Degel, A Akouch, N Borowski, M Reuter

For an optimal design and control of metallurgical processes, a deep understanding of the thermodynamics of the governing reactions is required. Modelling the thermochemical behaviour of those reactions is complex, as it involves multi-component and multi-phase systems. For this purpose, thermodynamic computing systems such as FactSage™ (Bale et al, 2016), which combine Gibbs energy minimisation routines with large databases of optimised thermodynamic data of solutions and compounds, have been used within the SMS group GmbH. Recently, the successful integration of those thermodynamic computing systems into the digital platforms of SMS has been achieved through ChemApp, which made running complex thermochemical calculations in Python-integrated development environments possible. ChemApp is a programmer’s package for thermochemistry and incorporates the Gibbs energy minimiser of FactSage™ as reported by Petersen and Hack (2007) as well as by Zietsman and Petersen (2018). The digital platforms link the fundamental and the industrial aspects together and can be applied as a process advisor, or for the evaluation of the environmental footprint and the economic implications of different process routes, as discussed by Reuter (2023). Two examples illustrating the progress of the developments in this regard will be introduced: 1. The Tilting Refining Furnace (TRF) for copper scrap recycling and refining to anode copper (the BlueControlApp). 2. Dephosphorisation control for the oxygen steelmaking process (Basic Oxygen Furnace (BOF)).

Jun 19, 2024

By J Loeb, J Dampney, P Cameron

Optimisation of Blast Design and Execution must be done right the first time. It is too late after the ore is broken. Consequences of poor design and execution negatively affect productivity from load and haul through the primary crusher to processing and hence reduce mine site profits. Harnessing and utilising ‘big data’ from geology, geometallurgy, drill hole location, powder loading, blast timing, blast movement and fragmentation to close the loop in blast design and optimise the blast increases productivity across the entire value chain from Mine to Mill. As the internet of things and artificial intelligence increases the quantity of data available, being able to capture and utilise this data to advantage is a challenge. Recent advances in software and hardware together with the increased power of cloud computing allows engineers to close the blasting loop to increase mine site productivity. Numerous case studies over the years detail significant gains from implementing the innovative technologies available to Mine to Mill projects. The opportunity is available for all members of the multi-discipline teams at each mine site to actively ensure productivity improvements are realised and maintained not only in their area, or silo of responsibility but across the entire mine site. This paper refers to recent case studies which outline how significant improvements in productivity are available to all mining operations to increase mine site profitability and dividends to shareholders.

Jun 22, 2022

By S J. Kim, S W. Kim, L Tomas da Rocha, S Jung

Al2O3 has been regarded as a harmful gangue component in iron ore, especially causing reduction degradation in industrial sintering of iron ore. The current study aimed to utilise low-grade iron ore containing high Al2O3 content in sintering process. In order to counteract the adverse effect of Al2O3 on reduction behaviour of iron ore sinter, mill-scale and calcined dolomite were chosen as FeO- and MgO-bearing materials. Firstly, mill-scale was added to high Al2O3 sinter and addition was optimised as 10 wt per cent, then calcined dolomite was added further. Magnetite and magnesio-ferrite were identified as the major phases in iron ore sinter when adding mill-scale and calcined dolomite. As the dosage of calcined dolomite increased beyond 4 wt per cent of in sinter mix, unreacted MgO particles were observed, which is ascribed to the limitation of MgO dissolution into magnetite matrix. Both mill-scale and calcined dolomite were effective in improving compressive load and Reduction Disintegration Index (RDI) of iron ore sinter although its reduction degree was highly decreased. The addition of both FeO and MgO-bearing materials to high Al2O3 sinter has a potential to improve the sinter quality, also contribute to the recycling of industrial by-product. However, the amount should be optimised in views of phase development and deterioration of reducibility.

Jun 19, 2024

By G Bournival, Y Saavedra Moreno, S Ata

Flotation frothers are heteropolar molecules that are preferentially adsorbed at the bubble interface to enhance the flotation performance by promoting the formation of small and stable bubbles. Frothers have different characteristics that can be used to classify them. A classification framework has been recently presented by Saavedra Moreno et al (2022) to classify non-ionic frothers by conducting a principal component analysis (PCA) and a hierarchical clustering analysis (HCA). However, for the purpose of the present research, only five frother characteristics, including molecular weight (MW), hydrophile–lipophile balance (HLB), critical coalescence concentration (CCC), the minimum Sauter mean diameter (DL), and foam stability index (DFI) were used in the PCA and HCA. All those characteristics were evaluated for a two-phase system in the absence of particles. Realising the important role that particles play in froth stability and behaviour, the effect of hydrophobic particles on the presented frother classification framework was investigated in this study. Four frothers with different characteristics, methyl isobutyl carbinol (MIBC), 1-pentanol, tri (propylene glycol) (TPG), and tri (propylene glycol) methyl ether (TPM), were chosen. The experiments were carried out in the presence and absence of silica particles esterified with 1-pentanol. It was evident that the results for 1-pentanol, TPM, MIBC, and TPG in the three-phase system agreed well with the frother classification presented for the two-phase system as frothers were clustered in the same groups. The findings from this research support the use of the frother classification system presented in two-phase system to select a specific frother for a particular application without the necessity of conducting laborious experiments in a three-phase system.

Aug 24, 2022

By C E. Woolley, H Jebaliya, J Foster

The East wall of the Kalgoorlie Consolidated Gold Mines Fimiston Open Pit (KCGM Superpit) has a history of wall instabilities impacting mining operations; the most significant of which occurred in May 2018, when more than 1 Mt of rock dislodged over six, 30 m high bench stacks and impacted the pit floor. Since 2011 approximately 1.250 Mt of material has fallen from the East wall at Fimiston Pit across three failure events (2011, 2018 and 2020). Each failure has been associated with major structures intersecting the pit walls: the Fiji Fault, the Australia East Secondary Splay Fault and the EWD3 Fault. In each instance the trigger for failure has been transient pore pressure in the pit walls. Northern Star will mine a cut back behind the failure area over a vertical distance of 180 m. Cut back mining will include the extraction of a remaining in situ wedge, which is assessed as kinematically able to fail, and a subvertical failure backscarp in Stage 1. A substantial amount of rill material from the 2018 and 2020 failures will be extracted in Stage 2. This paper presents the methodology in use to mine Stage 1 of the cut back, safely, through this potentially high-risk area, detailing the specific mining methodology employed, the controls put in place and the monitoring required. Day-to-day monitoring will be undertaken using the already installed slope stability radar and will feed into a daily assessment of activities which may be undertaken in the cut back area. Initial activities will focus on eliminating the potentially unstable wedge and vertical backscarp with use of innovative drill and blast techniques/products and the extensive use of remote capable equipment to limit personnel exposure.

Jun 22, 2022

By L Dzinza, K C. Corin, M Tadie

The recycling of process water comes with increased electrolyte concentrations that affect water quality, which may in turn affect the flotation performance of valuable minerals (Hirajima et al, 2016). Electrolytes such as Ca2+, SO4 2- , Mg2+ and S2O3 2- have been surmised to have an impact on the action of flotation reagents such as collectors (Ikumapayi et al, 2012). Xanthate collectors are known to play a significant role in imparting hydrophobicity on mineral surfaces to enhance their flotation. The interaction between minerals and xanthates is well known to be electrochemical in nature. Such redox processes may be elucidated by electrochemical techniques. Since the mechanisms involving the interactions between electrolytes in process water with sulfide minerals and the subsequent adsorption kinetics of collectors are not well understood, this study therefore aims to provide fundamental knowledge to unpack the mechanisms involved when electrolytes interact with Platinum Group Minerals (PGMs) and how these interactions may affect xanthate adsorption. The interaction of sodium iso-butyl xanthate (SIBX) in the presence of electrolytes at increasing ionic strength was investigated by rest potential measurements, to explain the impact of electrolytes on the adsorption of SIBX on PGMs in the flotation process. Rest potential measurements for PdTe2 and PdS were conducted in an air saturated 0.05 M di-sodium tetraborate decahydrate solution, in the absence and presence of SIBX and electrolytes. It was found that the existence of sulfide and telluride on palladium affects the mechanisms in which electrolytes interact with Pd mineral surfaces. An increase in the ionic strength of Na2S2O3, CaCl2 and MgCl2, increased the interaction between the salts and PdS, thus decreasing the extent to which SIBX interacted with PdS. An increase in ionic strength for Na2S2O3 increased the interaction between Na2S2O3 and PdTe2 and therefore decreased the extent to which SIBX interacted with PdTe2. Other salts investigated in this study increased the rate of oxidation of PdTe2 with an increase in ionic strength thereby enhancing the interaction of SIBX and PdTe2. This study has shown that mineral type, electrolyte type and concentration all have an impact on the mechanisms that result in the adsorption of SIBX on PGMs.

Aug 24, 2022

By T Suwa, S Ishida, J Xue, S Fuchida, H Shimada, Y Aoki, C Tokoro

Pyrite depression with prolonged pre-conditioning treatment in high salinity water has attracted much of researchers’ interest in recent years considering the increased utilisation of multiple stage flotation, closed water circuits, clay minerals, and sea water in flotation plants. In this study, the role of calcium (Ca)/magnesium (Mg) precipitates in stabilising the dissociative ferric hydroxy-xanthate (FHX), and its effect on modifying the balance of hydrophobic/hydrophilic species on the pyrite surface were primarily investigated. The total amount of extractable Fe-bearing species on pyrite concentrates and tailings after floatability test was quantitively determined using ethylenediaminetetraacetic acid (EDTA) extraction tests combined with inductively coupled plasma optical emission spectroscopy (ICP-OES). A more evident accumulation of extracted-Fe in pyrite concentrates rather than it in pyrite tailings was observed at both pH 9 and 10.5 when pyrite was pre-conditioned in Ca/Mg-bearing solutions for 360 min. Fourier transform infrared (FTIR) spectroscopy showed the main xanthate derivatives changed from di-xanthogen (1155 cm-1 ) to FHX (1167 cm-1 ) on the oxidised pyrite samples that were preconditioned in Ca/Mg-bearing solutions. Scanning electron microscopy-energy dispersive spectrometry (SEM-EDS) suggested the preferential accumulation of FHX upon secondary Ca/Mg-bearing precipitates as reflected by the higher Fe/S ratio together with the decrease of O element herein after xanthate conditioning. Although the hydrophilic secondary Ca/Mg/Fe-bearing minerals on the pyrite surface generally deteriorate pyrite’s floatability, the upper section of these secondary hydrophilic aggregates is partially covered by FHX alongside with further multilayer-adsorbed di-xanthogen. The precipitated Ca/Mg-bearing precipitates promotes the immobilisation of dissociated FHX derived from the reaction among iron oxyhydroxides and xanthate anions upon the localised secondary Ca/Mg/Fe-bearing minerals via acid–base complexation. Therefore, this phenomenon alleviates the hydrophilic modification of secondary Ca/Mg/Fe-bearing minerals to pyrite considering the immobilised FHX upon localised precipitates shows a slight hydrophobicity, and meanwhile, the upper FHX benefits the multilayer adsorption of di-xanthogen via the interaction among their inner hydrophobic alkyl chains.

Aug 24, 2022