Search Documents

THE question of dealing with the small quantities of copper found in a great many of the purchased ores became a factor of importance when the Sulphide Corporation decided to refine its own lead bullion, as the presence of this impurity has a marked effect on the efficiency of the de-silverizing operations of the Parkes process. Removal of the copper from the base bullion.The copper is removed from the base bullion by drossing, which collects the copper, and at the same time has considerable gold, silver, and lead values. The drassing of the bullion is done in two stages-firstly, at the smelters; and secondly, in thecopper kettles at the refinery. In both cases a "wet" dross is produced, which is subsequently "sweated" in a suitable type of furnace. When "dry" the dross is raked out and stored until enough accumulates to warrant a nUl on dross in the small blastfurnace kept for that purpose. A typical assay of the "dry" dross is as follows...WORKING THE DROSS UP TO LOW-GRADE CU-PB MATTEThe accumulated dross is treated in a small blast furnace with the necessary fiuxes, producing a low-grade Cu-Pb matte and base lead bullion.

Jan 1, 1920

THIS excellent volumetric method commends itself as a means of estimating the fineness of silver firstly, owing to the large number of possible impurities which do not affect its accuracy (these impurities include Cu-up to 70 % Au, Ph, Zn, Bi, Cd, Fe, Mn, Sb, and As); secondly, the method combines accuracy with speed. The above impurities are the only ones likely to be present in the B. H. A. S. Pty. Ltd. refined silver, and, with the exception of Cu and Au, the others, if present at all, would be well under 0.1 parts per 1000.Briefly stated, the method consists in the solution of the refined silver in HN03 , addition of ferric alum (indicator), and titration with an alkaline (either ammonium or potassium) thiocyanate solution until the brown ferric thiocyanate is formed, and gives a definite tint to the solution. The method is used at the Port Pirie smelters, and the outstanding feature in the method as there applied is the type of burette employed. This burette enables the operator to read 0.01 of a cc. with ease, whereas, with the ordinary burette fitted with a float, 0.05 of a cc., when a number of readings have to be taken, becomes very straining to the eyes. Moreover, waiting for the float to rise, and dislodging air bubbles from it, hinders rapid working.A description of the burette and fittings is appended with fig. 2. DETAILS OF THE METHODSolutions required are:a) Stock Solutions:(1) Ammonium thiocyanate, 40 grm. per litre of water; 30 litres are prepared and placed in a carboy with glass syphon attached.(2) Ferric alum, 250 grnl. per litre; two litres are prepared.

Jan 1, 1922

By R O. Laidlaw, J L. Mauk

The Coeur d'Alene mining district in northern Idaho, USA is the second largest producer of silver in the world. Mesothermal silver-lead-zinc veins occur in the metasedimentary rocks of the Belt Supergroup with five main types of associated hydrothermal alteration: 1) feldspar destruction, 2) hydrothermal bleaching, 3) carbonatisation, 4) sulfidation, and 5) silicification. Hydrothermal bleaching is characterised by hematite destruction with associated siderite and quartz veins and veinlets, coarse euhedral pyrite and magnetite. Bleached zones envelop both mineralised and barren veins and extend for metres to tens of metres into the wall rocks. Carbonatisation consists of addition of siderite, which occurs as veins, veinlets, stockwork, irregular blebs or spots, and coarsely disseminated grains, depending on the relative distance from the main vein structure. Siderite envelops nearly all mineralised veins, relates to all other alteration types and extends from several metres to tens of metres into the wall rocks. Pyrite and galena alteration dominate sulfidation and are associated with some mineralised veins. Pyrite alteration strongly correlates with siderite alteration and exists in three main forms: a) very fine-grained pyrite flooding, which can extend for metres to tens of metres into wall rocks; b) coarse-grained, euhedral pyrite, which is sporadic and associated with the redox boundary in hydrothermally bleached zones; and c) small isolated zones (6 - 15 cm) of medium-grained, subhedral to euhedral pyrite associated with pervasive siderite alteration. Where present, disseminated galena extends for metres to tens of metres into the wall rocks. Silicification is characterised by veins, veinlets, stringers, irregular patches and variable hardness in siltites and commonly appears in association with hydrothermal bleaching and siderite alteration. Although related to mineralisation, silicification is sporadic and in most places a clear envelope around mineralised veins cannot be identified.

Jan 1, 2001

By S Hayton

While coal seam gas is considered to be an unconventional gas, the proliferation of areas under exploration and development mean that it is rapidly becoming main stream. The potential of New Zealand's coals to produce coal seam gas has been recognised for some time. However, key market drivers have not been suitable for the progression of this potential into reality. Kenham Holdings Ltd and CRL Energy Ltd, recognising the potential for the gas in New Zealand have initiated what is the largest ever assessment of New Zealand's coal seam gas potential. The premature demise of the giant Maui field has raised the focus of new gas developments and has increased interest in what we are doing. Over the past couple of years Kenham Holdings Ltd and CRL Energy Ltd have approached the assessment of the coal seam gas potential in a staged programme. Preliminary assessment of the data on the permit areas indicates that the potential resource may be up to 500 PJ. To date, preliminary appraisals have been completed or are underway on a significant number of fields. Exploratory drilling has been completed or initiated on several of those fields, with results from this work being fed into the preliminary modelling as it has become available. Given that in many of these areas there is no pre-existing information concerning their gas potential and world wide experience with lignite is practically nonexistent, it has been a steep learning curve with many surprises. However, initial gas content results and preliminary gas flow models have been on the whole, rather pleasing, with the commerciality of some developments already apparent.

Jan 1, 2003

Rio Tinto Iron Ore (RTIO) manages eleven mines in the Pilbara region, Western Australia. Three of these mines have previously or are currently mining black shale that contains varying amounts of pyrite. Several new deposits currently being evaluated and existing mines that may progress below water table in the future, will also encounter this waste material. The black shale presents not just an acid rock drainage risk but also a spontaneous combustion risk. This paper presents the black shale management strategy and provides an overview of the relevant activities undertaken by RTIO. The strategy can be divided into two components which firstly involve defining the risk and secondly involve managing the risk. The mineral waste management plan is used to identify specific mineral waste hazards by:geochemical characterisation of waste material,undertaking mine site specific risk assessments,characterising the receiving environment,identifying sulfidic boundaries in geological and mining models,quantifying the amount of sulfidic material in medium and long-term mine plans, anddesigning and sequencing black shale waste dumps. Once a mine exposes black shale the Spontaneous Combustion and Acid Rock Drainage management plan is used and the major activities are: regular site meetings with a representative from every group that works with black shale;compliance with safe working procedures for site specific and detailed activities;regular training;the use of specific explosives to prevent premature detonation;ongoing geochemical characterisation;acid water management, monitoring and analysis;regular internal and external auditing of procedures and practices; andclosure planning assessments and preparations (ie cover trials, geochemical void modelling, geochemical waste dump modelling). The success of this holistic strategy is evident by the awareness of personnel within the business, thorough understanding of the geochemistry and by undertaking proactive management of black shale during mining. The strategy and management plans adopted by Rio Tinto Iron Ore have activities that other mine sites with potentially acid forming material may like to consider implementing.

Jan 1, 2009

Mining of copper ore is still the most important business in Chile. In order to mine ore with a copper content of less than one percent at Minera Los Pelambres in an economical way, opencast mining is mandatory. Due to the prevalence of avalanches at the mine, the concentrator was located in a stable area, some distance from the mine. As a consequence, the material has to be transported between mine and concentrator by conveyor. A downhill conveyor system has been implemented for more than ten years as the most suitable and most economical ore transport alternative. Due to the length (12.6 km) and inclination (1300 m drop) of the conveyor system, the stresses in the steel cord belt are the dominant design criterion, resulting in a belt quality of ST 7800. Additional dynamic belt stresses during transient operating conditions are avoided by the installation of high capacity adjustable frequency drives. The rating of a single drive unit is 2500 kW. During ten years of operation, several capacity increases have been implemented, from an initial 5800 t/h up to the current capacity of 9900 t/h. This presentation describes the engineering challenges of the implementation of the world's strongest belt conveyor system. Capacity increase measures like the development of new control and breaking strategy, proved by dynamic simulation of belt forces and belt speed scenarios are explained. During this long-term partnership of RWE Power International, the former Rheinbraun Engineering, with Minera Los Pelambres, RWE has been engaged continuously for development work, safety checks, expert opinions and maintenance audits, and giving new impulse to conveyor technology.

May 1, 2010

The introduction of a new mining method to Australia is not without its risks and challenges. This paper discusses the processes of planning a new operation, with particular emphasis on block caving and its Northparkes adaptation. As well as applying advanced technologies, here also is the opportunity to develop the art and science of block caving for its application to a wider range of geotechnical conditions than previously Envisaged.

Jan 1, 1995

The 1980's has seen a revolution in gold mine developments in Australasia. We are witnessing a near ten fold increase in all phases of gold mine development ranging from exploration through to production. Ounces produced have yet to mirror this activity but have increased from a low point of 600,000 in 1980 to 1,800,000 ounces in 1985 in Australia alone. In 1980 the region had less than 10 gold mines, yet 14 new mines started production in 1985 and as many as 28 might start up in the next 18 months. Developing gold mines in the 1980's in Australasia has not been the easiest of jobs, yet the great number of new developments suggest that we have entered a new era that will rank in history along with the 1850's, 1890's and 1930's as high points.Within- our Australasian region two very distinctive styles of gold deposits are being discovered and developed. On the Australian mainland the new mines are in geologically old rocks and are mostly the low grade haloes surrounding worked out high grade deposits. Most are limited life open pit operations depending on recent innovative carbon-in-pulp or heap leach technology. In the Pacific Islands region the style of discoveries are geologically recent, large bulk-low-grade deposits often geologically analogous to porphyry copper deposits. These deposits are typically 10 to 20 times larger than those being proved up on the Australian mainland.

Jan 1, 1986

BHP-Utah Coal Limited operates 33 draglines of varying sizes in the Bowen Basin of Central Queensland. The group's operations with draglines commenced in 1963 with the establishment of opencut operations at the then TPM Moura Mine and continued through expansion of that mine, the commissioning of the Utah Development Company Blackwater Mine in 1968, and the subsequent establishment of six (6) other large opencut mines, all in the general area over the next fourteen years. These operations generally commenced with boxcuts on the sub-crop at depths of 15 to 25 metres. Over the years, depths have increased so that average depths now are in the 45 to 50m range. It was soon realised that dragline operations would have to be supplemented with additional stripping equipment. In 1981, a symposium "45m and Beyond" was held in Rockhampton to assess the problems associated with such "deep" stripping. Subsequently, dragline operations have continued and although addi- tional stripping capacity has been added, in many instances, draglines have been used and are being used to dig depths greater than 45m, some- times as much as 65 to 70m.

Jan 1, 1989

The green field discovery of a two million ounce high-grade refractory gold ore deposit in the Indonesian Province of Sulawesi Utara, led Newmont to utilise its proven technical expertise in dry grinding and whole ore roasting to develop a 2000 tonne per day, 160 000 ounce per year operation in this remote and picturesque location.Located at an elevation of 250 in above sea level and ten kilometres to a deep water natural harbour, the hard rock open pit mine, process plant and infrastructure facilities were built to budget at a capital cost of US$132 million. The plant was commissioned with oxide ore, with the first gold poured in March 1996 and with refractory ore in January 1997. The operation rapidly met its production targets because of extensive forward planning and training programs developed for the local workforce. The presence of steep topography, fertile coastal plains, high rainfall, high seismicity of this location led to the decision to dispose of neutralised tailings in deep water off the coast instead of impounding tailings in a dam. This paper describes the development of the project and the challenges in developing a gold operation in a remote location which lacked infrastructure, the steps taken to ensure a smooth commissioning, and the selection of the workforce to operate a technically sophisticated facility.

Jan 1, 1997

This paper discusses equipment replacement strategies and specifically addresses the upgrading of technologically superseded equipment. The process of equipment replacement evaluations is reviewed, and areas have been highlighted where currently accepted practice results in a bias towards retaining existing equipment longer than otherwise justified. The Discounted Average Cost Method is described and the advantages of the technique for this style of decision making discussed. Several key issues influencing the replacement evaluation are also presented together with examples from recent consulting work.

Jan 1, 1992

Responsibility for the administration of mineral resources is divided between federal and provincial governments. The paper traces the evolution of mineral policies at both levels of government, from the end of World War II to the present. In the immediate post-World War II years, the emphasis was on supplying the raw material needs of a rapidly growing world economy. Policies favouring growth and development of the Canadian mining industry were instituted during this period. Two decades of uninterrupted expansion (the 1950s and 1960s) ensued. The decade of the 1970s was a turbulent one for Canadian mineral producers. Governments intervened more substantially than ever before. Moreover, the industry suffered from an intense period of competition for resource revenues by the two levels of government. At the same time, far reaching changes were taking place in the structure of world mineral markets. To date in the 1980s, the mineral industry has, perforce, adapted to existing mineral market structures. Mineral policies, too, have shown signs of adapting to the needs of the mineral industry. Whether the resulting mix of policies will permit the revitalization of the Canadian mining sector remains to be seen.

Jan 1, 1986

By P A. Tilyard

There have been enormous changes in mineral processing in the past four decades. For example grinding mill power has increased by an order of magnitude, regrinding is done to -10 microns and flotation machines are 100 times bigger. Operating staff have unprecedented opportunities for online monitoring and performance control of mineral processing plants. Sophisticated instruments can provide a plethora of data characterising the mineralogy and surfaces of particles. Digital computers allow complex calculations on huge amounts of data including modelling and simulation of machine and plant performance. However, all these changes have not necessarily lead to better metallurgical results. An analogy can be drawn with the thoroughbred racing industry in Australia. Significant advances in scientific knowledge in animal genetics, physiology, biomechanics and nutrition applied to the business have resulted in only a two per cent reduction in winning times for the Melbourne Cup and Caulfield Cup since the 1920s. A critical look at some mineral processing metrics suggests similar failures to improve performance despite putting in more resources. In fact certain parameters such as operating times and plant start-up performance are considered to have remained static or even deteriorated. There has been an emphasis on 'process' at the expense of 'outcomes'. The industry's strength has been in finding technical (or 'hardware') solutions while its weakness has been at the people end of the business in maximising and consolidating the gains from the technologies. Some trends in plant design over these years have exacerbated the apparent deskilling of operating and technical staff. Despite unparalleled options for communications, some staff are embarrassingly uninformed about technical developments in their fields. The 'boom and bust' cycles of the industry, together with trends in tertiary education and the effects of fly-in, fly-out (FIFO) operations, raise serious questions about the sustainability of human capital in the mineral processing sector. This paper by two experienced mineral processing engineers, with contributions from other senior practitioners, reviews these trends. While there may be an element of 'the older we are, the better we were', it is an attempt to identify the issues and propose solutions.

Jan 1, 2009

Many young mining engineers do not consider consulting as a possible job, believing that many years of working on-site is required to achieve practical experience, develop expertise and acquire industry contacts. However, mining consultancies employ engineers with varying levels of experience, including part-time university students, graduates and engineers who are relatively new to the industry. This paper outlines the role of a young engineer in a large mining consultancy and the benefits to both the consultancy and the client of having a mix of consultants with a diverse range of experience. From the authorÆs perspective, the work experience, lifestyle and rewards of mine consulting are compared to site based work, including a discussion on whether consulting is able to offer the professional development that a young engineer needs.

Jan 1, 2009

Between 1966 and 1976, Australia moved from being a non-producer to a position of meeting more than ten per cent of world nickel demand. New mine developments beginning the early-1990s have the promise of more than doubling the country's world market share - from around eight per cent to perhaps close to 20 per cent. This new surge in activity - the so-called `second nickel boom' - has led to several developments which seem likely to have similar economic impacts to those of the late- 1960s and early-1970s. There are, however, some notable differences this time around. The impact of long distance commuting over the past 30 years has changed the regional development scenario. The gold industry is much stronger in Australia than it was in the late-1960s and this helps to place the importance of new nickel discoveries in a more realistic perspective. As potential players have jockeyed to complete feasibility studies and move into construction and production phases of new long-life mines, established suppliers clearly seem to be taking actions to discourage the newcomers. In what appears to be a classic oligipolistic market situation, the heightening of perceived entry barriers to the industry appears to be a particularly visible strategy undertaken. In the current scenario as well, greater vertical integration among producers appears a significant influence on market power.

Jan 1, 1996

Australia is presently the world's principal producer of rutile and zircon, and also provides a major share of the world's ilmenite. Since 1980, Australia's share of the world's output of these minerals has fallen. Exhaustion of known resources, together with the changing composition of new deposits, is expected to result in Australia's share of the rutile and zircon output continuing to decline. Its role as a major supplier of upgraded ilmenite, that is synthetic rutile, is expected to increase. In 1994, the Bureau of Resource Sciences assessed Australia's demonstrated resources of mineral sands as follows: rutile 14.4 Mt, ilmenite 132.5 Mt, and zircon 21.0 Mt. These resources are located along the coast of Queensland and New South Wales, in the Murray Basin of New South Wales and Victoria, in the southwest corner of Western Australia, and in the Eneabba region, north of Perth. However, some 45 per cent of rutile and zircon resources along the coast of Queensland and New South Wales are not available for mining because of environmental concerns. World demonstrated resources are estimated at 40 Mt (contained TiO2) for rutile, 50 Mt for zircon and approximately 312 Mt (contained T1O2) for ilmenite. Outside of Australia, the most important resources of rutile, ilmenite and zircon are in South Africa (rutile, zircon , and ilmenite in the form of titania slag), Sierra Leone (rutile), India (ilmenite, zircon and rutile), and Canada (hard rock ilmenite). Significant resources of ilmenite occur in Madagascar and Mozambique.

Jan 1, 1996

The mmmg of alluvial gold involves many deposits of theMesozoic, Tertiary, and Quaternary Ages in processing. Majorfeatures of the composition of such alluvial deposits are the lowcontent of gold and the small size of the gold particles. Atpresent, the gold-miners treat alluvial deposits in which a portionof fme gold (0.25 mm) exceeds 45 per cent. It is expected that by2000 these resources will be the main deposits mined (Zamyatinet aI, 1991).Under real industrial conditions the losses of minus 0.25 mmmetal are 50 per cent and more. The low level of recovery of finegold is observed not only at concentrators equipped with sluices,but also at concentrators equipped with modern diaphragm andpistonless jigs (Table 1).

Jan 1, 1993

World class ore deposits can be defined commercially as deposits which contain metal concentrations in the upper quartile of resources size and/or grade, world wide, from which economic extraction can be undertaken, over a production period exceeding ten years, at a cost below the weighted average cost of cumulative production of the contained principal commodity of mines world wide.

Jan 1, 1993

The following thesis is an outcome of an investigation undertaken by the writer, at the suggestion of Professor Skeats, of the dykes and associated auriferous reefs of the Walhalla-Wood's Point belt, with the view of determining what relation, if any, existed between the petrological nature and the extent of llietasomatic alteration undergone by the dykes, and the genesis and localization of the gold.Although the greater part of the writer's time in the field and laboratory was occupied in studying the dykes and auriferous occurrences, a study was also made of the general geology as a basis for the special investigation. In addition, it soon became evident in the field that secondary enrichment had played a marked part in re-concentrating the gold and some interesting data in this connection have been collected. For example, indubitable evidence has been found of nuggets of gold having been formed by secondary processes.

Jan 1, 1920

Waihi Gold Mining Company Limited, a wholly owned subsidiary of Normandy Mining Limited, operates the Martha gold mine, located in the township of Waihi, New Zealand. The operation, an unincorporated joint venture, comprises Normandy Mining Limited (67.070/0) and Otter Gold Mines (32.94%). Since gold was first discovered at Waihi in 1878, it has formed a key part of the region's economy. In 1909 the Waihi mine was described in a report to Parliament as æthe most important gold mine in Australasia and one of the greatest in the world.Æ That was a record year for production, with 416,813 tons of ore mined and some 1,120 men employed. Today the mine produces up to 1,250,000 tonnes of ore annually, and the project employs some 234 men and women. In 1999 the value of the gold and silver produced ($59 million) made up 47% of Waihi's estimated GDP. Waihi Gold has made significant contributions to the Waihi economy, community and the Hauraki region as a whole. Since the mine was re-opened in 1987, thousands of local people have benefited from the mine. In 1999, consents were granted allowing an extension to the mine life (the Extended Project) and this will result in a further seven years of economic benefits resulting from mining activity. The Company has undertaken extensive consultation throughout project planning, construction, operations and rehabilitation. Ongoing liaison and involvement with all community sectors, including Tangata Whenua and Iwi, local residents, recreational groups and schools remains an integral part of the operation. Throughout the life of the modern Martha Mine, the Company has actively supported the local community in the form of donations, sponsorships, the provision of amenities, and by participating in community events. A well established environmental team exists at the site. Environmental and community performance is measured by an independent five-assessment process, and the Company is committed to achieving excellence through ongoing improvement programmes and staff awareness. When the mine is closed, the open pit area will be transformed into a recreational lake, and the tailings storage facilities will be rehabilitated to become a combination of wetlands, grassed areas and ponds. Resources will be provided by the Mine to ensure the rehabilitated site remains in a safe and self-sustaining, stable condition in perpetuity. The mine is regarded as a showcase on a world standard of how a modem mining operation can successfully coexist with the nearby community.

Jan 1, 2000