Search Documents

By D J. Williams, M S. Zbik, A Shokouhi

There is a considerable difference in the particle size distribution (PSD) of clay mineral-rich coarse coal reject with variations in the test moisture state and the chemistry of the water used for testing. The coarse coal reject tested were collected from Jeebropilly Mine, located in the Ipswich Coalfields of south-eastern Queensland. Differences between the results of dry and wet sieving analysis indicate a significant breakdown of the clay mineral-rich coarse coal reject on wetting-up. Wet sieving caused a breakdown of the gravel-sized fraction to silt and clay size without significant breakdown to sand size. There is also a considerable variation in the results of hydrometer analyses of the clay mineral-rich coarse coal reject with variations in the chemistry of the water used, particularly at the fine end of the particle size range. The waters used included tap water, coal processing water and deionised water. In addition, the method of dispersion applied prior to hydrometer analysis can have a significant effect on the PSD of clay mineral-rich coarse coal reject, with boiling and sonic vibration causing the most breakdown of the clay particles. This paper describes the testing methodology used and the test results obtained, and attempts to explain the results in terms of clay mineralogy and water chemistry.CITATION:Shokouhi, A, Williams, D J and Zbik, M S, 2015. Influence of water on particle size distribution of clay mineral-rich coarse coal reject, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 239–246 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By N Ganjian, A Delavar, F Rashidi Nejad

Iran is one of the most seismically active countries in the world, being crossed by several major fault lines that cover at least 90 per cent of the country. As a result, earthquakes in Iran occur often and are destructive. So, it is important to consider the seismic stability and reliability of all structures including tailings dams.In this study, the tailings dam stability of the Sangan Iron Ore Mine in Khorasan Razavi, Iran is considered for the case study. The tailings storage facilities of the mine have three cells with the capacity of 45 million cubic metres. The first cell, which has three stages of dam raising, has been recently brought into operation. This cell has a downstream-raised retaining embankment. As the risk of seismicity in this area is high, seismic response of this dam was evaluated by numerical methods. To do this, appropriate models were developed for materials used in foundation and body of the embankment. Then for seismic stability analysis, Tabas (Iran – 1978) and Chi-Chi (Taiwan – 1999) earthquake acceleration simulations were applied.The results of this study indicated that the upstream portion of Stage 3 of the dam and dam crest did not experience significant horizontal displacements during earthquake period, but the downstream portion of Stage 3 of the dam showed a maximum horizontal displacement of 60 cm at the third stage of dam raising. This is three times more than what was estimated by the designer. Also, the maximum vertical displacement resulting from simulation of the Tabas earthquake was 35 cm. The results of dam response to Tabas and Chi-Chi earthquakes indicate that displacement, shear stress and pore pressure by the Tabas earthquake were higher than the case of Chi-Chi earthquake. The higher energy of Tabas earthquake and the higher frequency near to the natural frequency of Tabas earthquake could be the reasons of this difference. The results of this case study confirm that if the studied tailings dam impacted by an earthquake of a similar magnitude to Tabas, the dam will be seismically stable and the developed strains will not be significant.CITATION:Delavar, A, Rashidi Nejad, F and Ganjian, N, 2015. Seismic stability analysis of Sangan Iron Mine Project tailings dam, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 173–182 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By D Anderson, W Timms

"A geotechnical centrifuge can characterise and model the interaction of tailings and fluids over very long time periods by accelerating drainage and consolidation processes. This technology can be considered an environmental ‘time machine’ for designing and evaluating tailings storage projects and verifying numerical models. The Broadbent G-18 geotechnical centrifuge (2 m diameter, up to 875 rev/min) and associated equipment is a unique facility commissioned in 2011 at UNSW Australia for applied research in low-permeability materials such as mine tailings. Two centrifuge modules are available: the permeameter module for characterisation and physical modelling and the strongbox module for physical modelling.This paper presents examples of geotechnical centrifuge applications for the: consolidation of slurries and dewatering design of earthen barriers compatible with tailings chemistry prediction of contaminant mobility. The specifications and capability of the UNSW Australia geotechnical centrifuge and associated instrumentation is also presented, along with preliminary analysis of the confidence intervals associated with permeability testing of a set of samples of varying heterogeneity. Drainage velocity through a mine tailings sample increases linearly with g-level in the centrifuge permeameter until tailings consolidation occurs. Alternatively, geotechnical centrifuge experiments can be designed to limit consolidation so as to quantify permeability changes that may occur with geochemical interactions between fluids and mine tailings or earthen containments. Reactive solute transport through mine tailings can be simulated at realistic solid:liquid ratios when chemical equilibrium is maintained during geotechnical centrifuge testing. Carefully designed physical models of tailings disposal tested at accelerated gravity can therefore provide a realistic evaluation of tailings consolidation and drainage and the potential for subsurface migration of contaminants from mine tailings over long time periods.CITATION:Timms, W and Anderson, D, 2015. Geotechnical centrifuge technology for characterising the interaction of tailings and pore water over decadal time periods, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 247–252 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 27, 2015

By T Napier-Munn, E Louwrens, L Keeney

Geometallurgical characterisation of ore deposits is accepted practice in some parts of the mining industry today. Its primary aim is to provide constrained inputs that reflect inherent geological variability and its impact on metallurgical performance for the deposit. Geometallurgy improves project value because it suggests more valuable alternatives for scheduling and processing through an increased knowledge and understanding of the interactions of rock properties and extractive technologies. Lower project cost (both capital and processing) and improved recoveries are the result from closer tailoring of the mining and mineral processing strategies to the characteristics of the resource (Dunham, Vann and Coward, 2011). Tailings storage facilities (TSFs) can be seen as potential resources and it is argued that fundamental geometallurgical characterisation as applied in ore deposit characterisation should also be applied to planning the retreatment of TSFs. This paper will describe a research project at Julius Kruttschnitt Mineral Resource Centre assessing if geometallurgical principles and methodologies can successfully be applied to TSFs as they have been to primary deposits. The project is establishing a new standard method of tailings evaluation which will include a 3D spatial model of the tailings resource. Initial domaining of the TSFs was done using principal component analysis followed by k-means cluster analysis based on chemical assays from drill core samples. The subsequent characterisation of the drill core samples has involved chemical, mineralogical and metallurgical profiling, with a range of metallurgical tests being conducted on the samples. This characterisation step is followed by class-based analysis, predictive modelling and process performance domaining with the ultimate objective of establishing a 3D spatial model incorporating geochemical, mineralogical and metallurgical performance data. This approach, which takes into account processing performance permits a more realistic (as compared to doing limited chemical assays and metallurgical testing) economic evaluation of the potential of reprocessing the tailings material. It is believed that the approach is generic and can be applied to other TSFs being considered for reprocessing. The present case study has also established the gold, copper, magnetite and cobalt deportment for an iron oxide copper-gold deposit tailings resource.CITATION:Louwrens, E, Napier-Munn, T and Keeney, L, 2015. Geometallurgical characterisation of a tailings storage facility – a novel approach, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 125–132 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By R Fanni, D Reid, M Kulessa

Recent updates to Australian industry guidelines emphasise the importance of the assessment of liquefaction potential of tailings. This includes assessment of the cyclic liquefaction potential, and the post-seismic strength of tailings expected to undergo strength loss from seismic loading. Despite this increase in focus, a relatively small number of Australian tailings appear to have been characterised through cyclic and post-cyclic testing. This paper presents the cyclic characterisation of four Australian tailings, consisting of iron ore, lateritic nickel, vanadium and bauxite residue. Material was obtained either from surficial tube sampling or through remoulding samples in the laboratory from slurries. Testing consisted of monotonic, cyclic and post-cyclic tests for each material. For three of the materials, laboratory-scale shear vane testing was also performed to provide a comparison to post-cyclic strengths from direct simple shear.The results indicated cyclic resistances consistent with the results of other tailings presented in the literature. The lateritic nickel tailings provided the greatest cyclic resistance of the four materials tested, followed by the vanadium tailings. This was somewhat consistent with expectations for material behaviour based on index properties. Post-cyclic strengths were seen to decrease as cyclic strains increased, consistent with typical observations in the literature. Following significant cyclic straining, in some instances the post-cyclic strengths approached those obtained through residual shear vane testing. This provides further insight into the strain-dependent nature of post-cyclic strengths for some materials. The implications of these observations on the post-seismic stability condition are discussed.CITATION:Reid, D, Fanni, R and Kulessa, M, 2015. Cyclic and post-cyclic behaviour of four Australian tailings, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 207–214 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By M S. Fenzel

Increased environmental regulations and pressures have created changing and new demands for tailings management strategies in a variety of mining applications. Critical among these items is the disposal of tailings as the pursuit of increased yields and lower costs have driven the application of different process technologies. With a number of technologies having a niche application focus, the belt filter press has been utilised for decades as a cost-effective and versatile option for dewatering different types of mineral tailings and other waste process streams. One of the critical advantages of the belt filter press is the technology’s ability to adapt and work in numerous plant designs, operating conditions and applications. As permitting and disposal options have become more stringent, plant designers, operators and equipment suppliers must develop comprehensive and site-specific economic, design and process evaluation techniques to ensure proper equipment selection and system design for belt filter presses or any other dewatering technologies. This paper will explore these techniques in relation to belt filter presses (with reference to other technologies) in a variety of different applications, along with other considerations to ensure a successful tailings dewatering system and disposal design. Summaries of equipment performance characteristics, operating and maintenance strategies and optimisation techniques will also be addressed in conjunction with the belt filter press’s adaptability to different plant designs and the resulting tailings characteristics.CITATION:Fenzel, M S, 2015. Analysis and adaptability of belt filter presses and other technologies for tailings dewatering over a range of mineral processes, plant designs, conditions, regions and operating philosophies, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 35–44 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By S Lehane, S Pearce

The characterisation and assessment of waste rock has been the subject of considerable research, and many guidance documents have been published both internationally and within Australia. While these documents provide detailed information on how to characterise waste rock, there is not a great amount of detail on how to determine the optimal waste management options from an operational viewpoint. For example, typical questions that a mine operator would seek answers to include: What placement method should be used (eg end tipping versus paddock dumping)? What is an optimal tip head height for waste placement in a storage facility? How should sulfide grade control be carried out?Defining the contributing factors to waste management and waste material placement and assessing the contribution of each variable directs these assessments towards a semi-qualitative and quantitative methodology. Quantitative methodologies show an increase in the confidence of these assessments by providing logical, measureable assessments.As part of a strategic assessment for waste management at an active mine site, a detailed risk-based investigation of the influence of variables common to waste placement was completed. These variables included placement method, placement height, sulfur grade and material conditioning (eg compaction) on the associated risks of waste material storage. The assessed risks include temperature assessments (potential for thermal take-off as a result of spontaneous combustion), toxic gas production and flow and acid production potential. Applying a numerical modelling approach to the assessment of the different waste material placement strategies allows for the variation in risk to be graphically presented and communicated through risk matrices and histograms.CITATION:Pearce, S and Lehane, S, 2015. Quantitative risk assessment tools to assist with waste management and placement guidelines, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 353–364 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By S Thacker, M Noakes

The Newmont Tanami Operations (NTO), formerly the Granites Gold Mine, commenced operation in the mid-1980s with tailings deposition evolving over the past three decades as production has increased and the operation has expanded. Paddock-style tailings storage facilities (TSFs) and in-pit tailings deposition have fulfilled the tailings requirements for NTO over its lifetime with the technical specifications of these facilities improving over time in line with the positive development of standards, guidelines and best practice.This paper reviews the options for tailings storage facilities at NTO and the many considerations that have been analysed and deliberated upon before settling on specific TSF types and designs. It also explains the operating philosophies of the tailings deposition and how the facilities have always strongly maintained the optimum capture and retrieval of water. The current TSF design and criteria is presented, along with the introduction of dry tails harvesting for use in paste production as a backfill product for the underground mine. Tailings deposition and recovery remains a critical function of the Granites process to ensure long-term operation and gold production.CITATION:Thacker, S and Noakes, M, 2015. Newmont Tanami Operations – tailings storage facilities, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 305–314 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By D Luppnow, C Hore

In-pit tailings storage can provide many advantages when compared to typical above-ground tailings storage facilities (TSFs). As regulations become more restrictive and existing mines expand into new pits, the motivation and opportunities for in-pit tailings disposal is increasing.The Langer Heinrich uranium orebody follows a palaeo-river channel and is mined as an open pit operation. The mine pits intersect two main aquifer systems, one at the surface and one at the base of the orebody/pits. The tailings storage methodology is full in-pit disposal in multiple TSFs for the life-of-mine. Continuity of the initial hydrogeological conditions is incorporated in the design by the use of the pervious surround concept and the reinstatement of the lower aquifer (palaeochannel aquifer) at the base of the pit. Containment embankments are required to facilitate the staging of the TSFs development and are constructed using waste rock liberated during the mining of the pits. All of the TSFs are equipped with decant structures and an underdrainage system is included to improve water recovery, enhance consolidation and increase tailings density.This paper presents the design of a unique in-pit tailings storage solution for the Langer Heinrich mine in Namibia owned by Paladin Energy Ltd.CITATION:Hore, C and Luppnow, D, 2015. In-pit tailings disposal at Langer Heinrich – tailings storage facilities in a unique hydrogeological setting, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 373–380 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By P J. Vardon, L A. van Paassen, Y Yao, A F. van Tol

Thin-lift atmospheric fine drying (AFD) is a technique used to dewater mine and oil sand tailings, which utilises both self-weight consolidation and atmospheric evaporation. The disposed layers undergo a cyclic drying and rewetting process due to precipitation and deposition of additional lifts on top of the dried layer. The current research aims to optimise the deposition process via use of a numerical model and realistic atmospheric conditions, including both periods of drying and wetting. The model is based upon water balance and includes large strain considerations. A number of material behaviours are characterised using empirical fitting curves based upon laboratory measurement of material characteristics, including both the shrinkage and water retention curves for drying and rewetting. The model is able to model multiple lifts, simulating field scale and realistic climatic conditions within timescales suitable for engineering practice (eg seconds or minutes). The model has been previously validated against controlled laboratory experiments and utilised to simulate field tests. A series of simulations are presented to illustrate the ability of the model to be used as a practical tool for the optimisation of a tailings deposition strategy.CITATION:Vardon, P J, Yao, Y, van Paassen, L A and van Tol, A F, 2015. The use of a large-strain drying and consolidation model to optimise multilift tailing deposits, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 263–270 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By Y Li, Z Fu, D J. Williams, E Topal

Mine waste rock is unavoidable in the recovery of ore by open pit mining methods. Effective management of waste rock movement covers the removal and placement of the waste rock, generally in a surface dump in the most cost-effective way while satisfying the long-term environmental expectations. Since the 1960s, there has been significant research carried out into planning of ore movement from open pit mines such that the overall net present value (NPV) of the project can be maximised. Currently, several software packages are available to achieve this task as a common practice within the mining industry. However, planning of mine waste rock movement is still achieved manually, as the available software does not consider optimal waste rock movement and dump design. This paper describes a tool to optimise waste rock placement, which minimises the haulage cost while creating environmentally friendly waste rock dumps through selective placement and encapsulation of the reactive waste rock in the dump. The embedded methodology in this tool has been developed based on the mixed integer programming (MIP) modelling technique to optimise the waste rock movement. The methodology provides an easily-manipulated and fully-automatic tool for professionals to complete waste rock dump scheduling in four main steps: data input, model construction, model computation and solution retrieval. The application of the new tool into a real case project in this paper shows that it can determine economically and environmentally optimised waste rock dump schedules in an acceptable time frame.CITATION:Fu, Z, Li, Y, Topal, E and Williams, D J, 2015. A new tool for optimisation of mine waste management in potential acid forming conditions, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 333–342 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By H Barrie, L Ameglio

"Current methods for acid rock drainage (ARD) mitigation revolve around insulation of the waste from oxygen in the atmosphere with water and dry (soils and liners) covers. Both are of limited effectiveness and present significant drawbacks. Furthermore, while they reduce oxygen influx, they reduce but do not prevent ARD.The inert gas mixture (IGM) technology has been designed to overcome the deficiencies of gas transfer into tailings and waste rock materials across the surface and instead block oxidation by controlling the transfer of oxygen from the atmosphere. Inert gas is injected into the mine waste at low flow rates and the positive but low flow purges the oxygen that tends to diffuse into the sulfide waste across the surface. The positive flow of IGM compensates for inward oxygen diffusion and creates a pressure drop across the cover layer preventing inward diffusion of oxygen and, hence, acid generation.The IGM processes are evaluated in this paper: theoretically, with a review of the theory of ARD and the current state of knowledge about the performance of notably dry covers as atmospheric oxygen barriers via models to predict the performance of the IGM technique practically, with a bench-scaled experiment.The results demonstrate the effectiveness of IGM to prevent oxidation of sulfide minerals and ARD in waste rock. The laboratory experiments further identified key variables to be used to monitor performance and control efficiency of IGM, which is now awaiting field-scale application.The IGM technology is a patented process by Terraquest Technologies Ltd (Canada) in USA, Canada and Australia. The IGM technology can be cost-effectively manufactured on-site with commercially available compressors and gas filtration membranes. It is predicted that low-cost covers can then be utilised with IGM, which in turn lowers the overall capital costs of ARD mitigation.CITATION:Ameglio, L and Barrie, H, 2015. Acid rock drainage prevention using inert gas mixture technology, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 85–96 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 27, 2015

By J Pearce, M Barteaux, S Pearce

The prediction of how waste materials will evolve geochemically within waste storage facilities has been the subject of hundreds of thousands of hours researched by geoscientists globally. Despite the quantity of research there are a number of significant areas of uncertainty that remain as partially resolved issues. One of the most significant issues is the applicability of scaling laboratory test results to field conditions, and the use of laboratory data for predictive calculations to determine geochemical evolution of waste materials in the field. This issue has arisen predominantly as a result of the relative paucity of field monitoring data from waste rock storage facilities (WRSFs) and the fact that laboratory test methods are not typically linked to specific field conditions; rather they are based on generic standardised methods and designed primarily to simulate accelerated weathering conditions that do not relate to field conditions in a linear manner.To address these specific issues the authors have in the last two years made significant progress in the development and deployment of advanced field monitoring equipment within numerous WRSFs. O’Kane Consultants (OKC) has previously reported the findings from data collected from these monitoring installations in a number of papers presented throughout 2013–2014. This valuable site data has subsequently been used by OKC as the basis to design and engineer advanced customisable site-specific kinetic leach columns at OKC’s geochemistry research laboratory. These columns represent an important advancement in kinetic column assessment methodology as they have been designed to replicate the field internal conditions within waste facilities.Key features of the columns include their capacity, size and technical specifications; including fully programmable solenoid-controlled air supply with variable flow and pressure control and in-line heating option, automated temperature control and monitoring, automated oxygen consumption and carbon dioxide production monitoring, and soil moisture/matric suction monitoring.This flexibility of the design not only allows for more accurate field-based assessment of pyrite oxidation rates (POR) but also assessment of the potential effectiveness of waste management options such as deposition within a reduced oxygen environment, for example, as simulations of reduced net percolation rates or oxygen ingress rates can be accommodated.CITATION:Pearce, S, Pearce, J and Barteaux, M, 2015. Advanced customisable leach columns – a new kinetic testing method to simulate site-specific conditions, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 137–144 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By K Banerjee, C Dube

Veolia Water Technologies was contracted by a global coal mining company to design a retrofit acid mine drainage treatment facility using DenseSludge™ technology on a former coal refuse disposal site. The project constraint was to reuse current facilities in order to reduce additional capital work cost and avoid additional footprint requirements while improving treatment performance and reducing sludge production and chemical consumption. The initial installation of 454 m3/h served as a pilot plant to demonstrate the benefits of the process and ultimately provided design criteria for the new facility. The pilot demonstrated the benefit of the technology by reducing sludge volume by 90 per cent compared to conventional processes currently in use. The sludge that is reinjected into the mine contains less water, which reduces the volume of water that returns to the mine pool for treatment and mine water balance. Furthermore, the pilot plant reduced lime usage compared to conventional processes by operating at a lower pH set point, demonstrating steady pH control and stoichiometric lime utilisation.CITATION:Dube, C and Banerjee, K, 2015. Sludge conditioning technology to reduce sludge and the cost of acid mine drainage treatment, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 105–110 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By D Reid, A Fourie

The in-pipe treatment of slurries with polymer addition shortly prior to deposition is a noteworthy emerging technology of increasing popularity. Although polymer treatment has been shown to substantially modify and improve depositional and dewatering behaviour in a significant number of cases, the impacts of polymer treatment on geotechnical performance of tailings are less well understood. For example, certain combinations of polymer and slurry type have been shown to result in lower final densities at a given vertical effective stress. Despite these lower densities, polymer-treated tailings often exhibit peak undrained shear strengths consistent with untreated material. However, the sensitivity and/or brittleness of the material may be negatively influenced by the looser state created. Although these changes have been studied, most testing available in the literature was undertaken on relatively ‘fresh’ samples of polymer-treated material. However, significant shear may occur following treatment and prior to the commencement of settling and self-weight consolidation as the material moves down the beach.To study the effects of shearing on the subsequent performance of polymer-treated tailings, a test program consisting of consolidation, triaxial and direct simple shear tests was undertaken on presheared polymer-treated material. Materials used were identical to those used in previously published studies on the impacts of polymer treatment in a ‘fresh’ condition. Shearing of the polymer-treated material generally appeared to lessen the impacts of the polymer treatment process. However, the behaviour of the material when sheared indicated that the polymer was still impacting the behaviour of the material in some respects. The results indicate the importance of the consideration of shearing on material behaviour when planning and designing a tailings deposit where polymer treatment is to be implemented.CITATION:Reid, D and Fourie, A, 2015. Effects of shear on the behaviour of polymer-treated slurries, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 215–224 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By P Kappen, R N. Collins, K M. Spiers

X-ray absorption spectroscopy (XAS) is a synchrotron-only technique used to determine chemical speciation, providing a powerful alternative to most traditional ‘wet chemistry’ and lab-based speciation methods. XAS is an element specific method that can be used to address a variety of systems, ranging from heterogeneous to homogeneous, polycrystalline to amorphous, and solid to liquid. The strength of XAS in identifying and managing chemical species in tailings and mine waste is demonstrated, with the presentation of highly relevant studies into lead, uranium, chromium and arsenic speciation. In each example, waste samples are compared with known standards, allowing an assessment to be made of the quantity of particular chemical species in each.CITATION:Spiers, K M, Collins, R N and Kappen, P, 2015. ‘Forget the wet chemistry’ – how the Australian Synchrotron can help with tailings and mine waste management, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 145–148 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By D J. Williams

The approach to the disposal and storage of mine tailings is slowly evolving. Tailings disposal has been based on minimising short-term capital and operating costs, with rehabilitation costs discounted by the application of a high discount factor in a net present value approach to accounting. This has led to the widespread adoption of surface tailings storage facilities (TSFs) to store slurried tailings delivered by robust and cheap centrifugal pumps and pipelines. Depending on the site climate, rate of rise of the tailings, nature of the tailings and the extent to which supernatant water is removed from the surface TSF, the tailings may or may not dewater, densify and gain strength. High rates of rise of dilute tailings to a facility used to store both tailings and supernatant water results in a wet, low-density, soft tailings deposit that not only occupies a large storage volume but also presents rehabilitation difficulties. A low tailings density results in high containment wall costs, very high rehabilitation costs and a low potential for future land use or ecological function. Overall, the cost of slurried tailings disposal, thought to be low, is actually high. However, low rates of rise, even of dilute tailings, in a dry climate with efficient supernatant water removal can produce a dewatered, high-density, stiff tailings deposit that may occupy a large footprint but to shallow depth that is relatively easy to rehabilitate. There are advantages in dewatering tailings in the processing plant to recover process water and chemicals, facilitate tailings disposal in a more solid form and facilitate rehabilitation. However, the cost of dewatering in-plant can be high, and the process water may not lend itself to reuse. There are also advantages in removing supernatant water to facilitate solar and wind drying of exposed tailings, although water is lost to evaporation and the dried tailings may best be harvested prior to inundation by fresh tailings or rainfall run-off. This paper discusses the background and trends towards the elimination of conventional surface slurried TSFs, with examples presented of the management of black coal and other tailings, including those that are clay mineral-rich.CITATION:Williams, D J, 2015. Towards the elimination of conventional surface slurried tailings storage facilities, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 11–24 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By T Huynh, K Tungpalan, E Wightman, M Edraki, S Palaniandy

Most preventive environmental management practices promote proactive integrated approaches to waste management. For example, life cycle assessment is often used to find the ‘hot spots’ of environmental burdens. This kind of approach is often based on generic data and has rarely been used for tailings. Besides, life cycle assessments are less useful for designing operations or simulating changes in the process and consequent environmental outcomes. It is evident that an integrated approach for tailings research linked to better processing options is needed.The aim of this Nextmine™ project is to develop new tailings management models by streamlining orebody characterisation, process optimisation and rehabilitation. We present an integrated tailings management approach and preliminary results from a case study. Combined grinding and flotation models were developed using geometallurgical data from the orebody, to predict the properties of tailings produced under various processing conditions. The modelling scenarios based on the case study data provide the capacity to predict the composition of tailings and the resulting environmental management implications. For example, the type and content of clay minerals in tailings will affect the geotechnical stability and water recovery. Clay content will also influence decisions made for paste or thickened tailings and underground backfilling.CITATION:Edraki, M, Huynh, T, Wightman, E, Tungpalan, K and Palaniandy, S, 2015. An integrated approach to proactive tailings management, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 323–332 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By D Veneziano, J Van Dyck, R Snow, W Pytel, O Zanoli

Best practice standards generally recommend assessment of the environmental and societal risks posed by tailings storage facilities, but they rarely specify how the analysis should be made. As a case study, this paper describes a safety assessment of the Zelazny Most tailings pond operated by the Hydrotechnical Unit of KGHM Polska Miedz SA in Poland. The complete assessment includes a failure mode effect criticality analysis (FMECA) that considers all conceivable failure modes, but this paper focuses on one key mode, the loss of stability during the planned raising of the crest above its current level. Reliability against static dam failure considers uncertainty on the safety factor in a limit equilibrium approach. The threat of dynamic (earthquake induced) instability is assessed by developing a model of future seismicity as a function of the mining plan and considering uncertainty on the induced permanent displacements along critical sliding surfaces. We quantify the additional level of protection against outflow provided by the beach using an event tree with expert-assigned probabilities. Continuous monitoring of the dam for premonitory signs of instability and a set of loss-prevention plans in the case of a spill provide additional layers of protection; their effectiveness is quantified by estimating the fraction of the population that could be evacuated as a function of warning time. The probabilistic analysis indicates that the safety targets are met and produces practical recommendations on how to maintain and improve the safety level while the dam crest is raised above its current level.CITATION:Van Dyck, J, Pytel, W, Veneziano, D, Snow, R and Zanoli, O, 2015. Safety of a tailings storage facility against dam instability, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 253–262 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By D Luppnow, H Rourke

Recent disasters such as the failure of the Mount Polley tailings embankment remind us of the risks that tailings facilities pose. It is widely recognised that dam-break assessments are a vital tool in identifying the consequences of the failure of a facility, which in turn can be used to develop emergency action plans. A typical assessment includes an estimation of breach parameters and outflow volume, followed by the preparation of an inundation map to illustrate potential flow extents and downstream impacts. This paper focuses on the estimation of outflow volumes, which is an area that the authors feel can be improved. Presently, many types of analyses assume that the volume of tailings released is only a function of the storage volume and dam height. After a review of several documented tailings failures, it has been found that the extent and depth of the supernatant pond needs to be considered as it is just as important, if not more so, as the storage volume and dam height. Tailings facilities with excess water storage have a higher risk of failure as they are more susceptible to overtopping, piping and liquefaction failures. In addition, they pose greater failure consequences as the saturated conditions will lead to more material being mobilised.This paper has reviewed available information on a number of tailings dam failures and proposes an alternative estimation of potential tailings release volumes as a function of supernatant water stored on the facility for use in dam-break analyses. In a broader sense, the paper seeks to shift the current risk paradigm from tailings dam heights to volumes of water stored and provides a basis for continuing research and discussion.CITATION:Rourke, H and Luppnow, D, 2015. The risks of excess water on tailings facilities and its application to dam-break studies, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 225–230 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015