Search Documents

By Mark J. Klein

The precipitation of nitrogen in quenched and aged CY-35 at. pct Re was followed by internal-friction and electrical-resistivity measurements. It is shown that the precipitation kinetics of nitrogen from solution are many orders of magnitude lower in this alloy than in chromium. The reluctance of nitrogen to precipitate from sol~ction can be attributed to the composilional r-eadjustnzents required in the z.icinity of a chromium nitrade particle for gowth to occur. AS part of an investigation of the mechanism by which rhenium increases the low-temperature ductility of chromium and other Group VI-A metals, it was of interest to compare the concentration of interstitial elements retained in solution in chromium with that of a ductile Cr-Re alloy. The presence of certain interstitial elements in chromium has been shown to decrease its ductility1-5 and, of these interstitials, nitrogen is believed to have the most detrimental effect on mechanical properties. Thus, a comparison of the disposition of nitrogen in chromium with that in a ductile Cr-Re alloy might provide information about the mechanism whereby rhenium enhances the ductility of chromium. In previous internal-friction studies it was shown that the equilibrium solubilities of nitrogen in chromium and Cr-35 at. pct Re did not differ greatly.= However, results indicated that the actual concentration of nitrogen retained in solution at ambient temperatures is likely to be considerably greater in the alloy than in chromium because the precipitation kinetics of nitrogen are greatly retarded by the addition of rhenium. The objective of this investigation was to study the kinetics of nitrogen precipitation in Cr-35 at. pct Re in greater detail and to obtain information concerning the mechanism of nitrogen precipitation in this alloy. The properties studied were internal friction and

Jan 1, 1967

By B. H. Bergstrom

The Gaudin-Meloy1 size distribution equation requires the evaluation of two constants, xo and r. The common log-log representation of a screen analysis as cumulative weight percentage passing versus size, readily yields the required constants as illustrated for curves A and B in Fig. 1. The 100% passing (y = 1.0) size is simply x,. If the straight portion of the curve be extrapolated to the 100% passing (y=1.0) abscissa, the intercept is the Schuhmann size modulus, k. The ratio of xo to the size modulus, k, is r as shown: The Gaudin-Meloy equation requires that the slope, a, of the size distribution approach unity in the finer sizes, as is the case for curves A and B. Often distributions are better characterized by slopes other than unity. The schuhmann2 equation is able to represent these distributions if the upper portions of the curves are ignored. Empirically, the Gaudin-Meloy equation can be modified to yield slopes other than unity by writing it as Here, a is the familiar Schuhmann slope, and xo is the 100% passing size. The value of r is still given by Eq. 2. Eq. 4 with its easily determined constants is more versatile than either the Schuhmann or the Gaudin-Meloy equations, since a wide variety of size distributions can be closely described. It is easier to fit than the Rosin-Rammler3 equation, and has the advantage that the top size, x,, is finite. REFERENCES A. M. Gaudin and T. P. Meloy: Model and a Comminution Distribution Equation for Single Fracture, AIME Transactions, 1962, Vol. 223, pp. 40 to 43. R. Schumann, Jr.: principles of comminution, I., size Distribution and Surface Calculations, AIME Technical Publication No. 1187, 1940. P. Rosin and E. Rammler: The Laws coverning the Fineness of Powdered Coal, J. Inst. Fuel, 1933. Vol. 7, p. 29.

Jan 1, 1967

By D. W. G. White

The surface tension of zinc has been determined by the sessile-drop method in a progvam emphaszzing detailed experimental care. The surface tension oj. the pure metal was measured over a range of ternperature from the melting point (419.6"C) to 540°C. At the melting point, the suvface tension of zinc was found to be: 1) 99.99+ pct Zn - 757.0 5 dynes per cm 2) 99.999+ pct Zn - 761.0 5 dynes per CI 3) 99.9999 pct Zn - 76'7.5 5 dynes pev cna From experiments carried out in a closed, isothermal cell, the temperatuve coejyicient of the surface tension (6y/6T)p, , of zinc xas found not to be negative but to be postiue. A positive tenzperatre coefficient indicates a greater depee of order in the surface than in the body of the lquid. Houlezer, by delibevately inducing continuous zaporization, a temperature coefficient of su)face tension with a negative slope can be produced. The work reported herein was undertaken as part of a larger program of fundamental research on the properties of molten zinc and zinc alloys. This program grew out of a continuing interest at the Mines Branch in the behavior of liquid metals in the foundry and of a desire on the part of the zinc industry for reliable basic data. The work was originally begun in cooperation with the Consolidated Mining and Smelting Co. Ltd., Trail, B.C., and was subsequently continued from 1960 to date in association with the Canadian Zinc and Lead Research Committee and the International Lead and Zinc Research Organization. Although the surface tension of liquid zinc has of course, been measured before, as Table I and Fig. 1 demonstrate, there is not good agreement among the existing values. Such disparities arise because sources of experimental error are insufficiently controlled. This situation places the reader in doubt. One result may be correct within narrow limits—even fortuitously—yet, because there is not agreement between several values, none can be accepted with conviction and all become suspect. It seemed, therefore, in the circumstances, that there was room for further work embodying considerable emphasis on experimental care in order that, within a small margin of error, an accurate value might be obtained. It was in this spirit that the work was undertaken. METHOD The sessile-drop method -as adopted for this work. In this method, when applied to liquid metals at elevated temperatures, the outline of the meridional section through a drop resting freely on a horizontal surface is recorded photographically. Certain parameters

Jan 1, 1967

By J. V. Gluck

In the present paper," as in earlier publications, V1'2"1 the authors present experimentally obtained relations for the free energy of solution of oxygen in various metals as a function of temperature. The relations are linear and given in slope-intercept form. The authors give values for the "probable error" of the slope and intercept, citing Birge's method17 for obtaining these quantities. Birge discussed these methods as early as the period 1929-32.25726 In Ref. 25 the probable error is defined as "the numerical value which the true error is as likely to exceed as not", i.e., 50 pct probability. Ref. 26 is even more detailed and includes a lengthy discussion of the applicability of the Gaussian distribution to experimental data. However, the use of the "probable error" has come under some question. For example, Ezekiel'~ states that "the use of the probable error tends to make the results appear rather more accurate than the standard error". Moroney28 stated (in 1951) that "the term 'probable error' was used in former times to denote 0.67450 (50 pct confidence using the normal distribution)....the term, a poor one, is now very much obsolescent. It has been said that 'it is neither an error nor probable' ". Bennett and Franklin in 1954" in discussing statistical confidence levels mentioned that "the customary use of the 5 and 1 pct levels is not completely a matter of chance; these levels probably represent a balance between the desire to be correct and the desire to be specific. Also in most people's minds the borderline between something that could possibly happen and something that is not likely to happen is somewhere in this region. Certainly 5 or 1 pct confidence limits are to be preferred to limits such as the 'probable error' which has only a 50/50 chance of including the correct value." It may readily be seen that the 95 pct confidence level, which is given by 1.960 (assuming large sample size), thus corresponds to approximately three times the "probable error". Indeed, limits of one standard deviation correspond only to about 68 pct probability. Even if we triple the tolerances given by the authors in the equations of their Table 111, the deviations do not become excessive and would not detract from their excellent results. It could then be said with a high degree of confidence (95%) that the precision of the slope and intercept values is about *3-5 percent of their absolute levels rather than the 1-2 percent implied in Table 111. This is then compatible with an earlier suggestion of Gokcen~' of a probable accuracy of 5 pct in dissolved oxygen measurements by the technique employed. Alternatively, the authors could have

Jan 1, 1967

By B. A. Shaw

Historically, microwave tubes have been fabricated from massive metal and ceramic components. The current trend is to lighten tibes for airborne applications. The reqciiremenls of light weight and also reduced cost have created a novel approach to tube structure in which thin-film technology plays a major role. Although the electrical requirements of thin-film circuits in microwave tubes differ from those required or se,niconductor integrated circuits. the technology is basically similar. The stringent requirements of the micvowave tube have created sophisticaled thin-film techniques thut are of interest to the integrated-circuit industry in general. This paper describes a nunzber of thin-jilm techniques recently developed and discusses in detail the application of the technology in microwave tubes. The particular areas of interest are: 1) ceramic mounted thin-film slow-wave structures; 2) thin-film secondary emitters; 3) suppression of tube environnental multipactor by semiconducting' thin films; and 4) age-hardenable and dispersion-hardened thin metal films. SEVERAL thin-film techniques specifically applied to microwave power tubes are discussed in this report. There are two reasons for this work. One is the necessity of reducing weight and cost of microwave tubes and the other is related to overcoming problems in the tube operation by the use of applied thin-film technology. The major emphasis of this work has been on tube slow-wave structures. Other work in the area of secondary emission, either its suppression or its enhancement, is continuing; the most satisfactory results to date have been by utilization of thin-film technology. The requirements of high thermal and electrical conduction together with greater strength than normally obtained with elemental materials have led to the development of dispersion-hardened films. The paper will discuss: 1) ceramic-mounted delay-line microwave tubes; 2) multipactor and secondary emission; 3) hardened films. I) CERAMIC-MOUNTED THIN-FILM SLOW-WAVE STRUCTURES In a conventional crossed-field microwave tube, the slow-wave or delay-line structure is produced from two carefully machined components. One half of the structure is shown in Fig. 1. The other half is the mirror image of the first but is rotationally offset by a half a period. The combined structure now forms an interdigital type of slow-wave structure and is the anode of the tube as shown in Fig. 2. The period and finger length of an interdigital slow-wave structure are prescribed by the desired dispersion characteristics. The typical design is as shown in the first figure; it can be noticed that the finger width is several times greater than the finger thickness. Even assuming that it were mechanically possible to produce free-standing fingers of extremely small cross-sectional dimension, for example, 0.002 in. thick by 0.005 in. wide by 0.500 in. long, decreasing this finger width would increase the tube efficiency but would also decrease the thermal-conduction path, causing an increased temperature rise from intercepted rf current which in its extreme could easily cause finger melting. Hence, for free-standing lines of this type, the design is a compromise between mechanical capabilities, tube efficiency, and thermal dissipation. These structures are also expensive and tend to be heavier than purely electrical considerations would demand. In the present approach, we have transposed the three-dimensional structure previously shown into an essentially two-dimensional structure as shown in Fig. 3. The linear structure is used here for clarity of detail. The support member is a ceramic material and the line is deposited copper. The final tube design is shown in Fig. 4. Because of the backwall sup-

Jan 1, 1967

By O. J. Kensok

THE literature contains three previous studies of the chemical activities of Cd-Mg alloys: Trumbore, Wallace, and craigl obtained chemical activities of magnesium at 543" by performing electromotive-force measurements; Borg and irchenall calculated activities at 590°K based on vapor-pressure measurements of cadmium over Mg-Cd alloys by the Knud-sen effusion method; and Terpilouski and arcka measured the chemical activities of magnesium in the liquid state by means of electromotive-force measurements. In this study the vapor pressure of cadmium was determined over nine solid Cd-Mg alloys in the temperature range 571" to 697°K by the Knudsen effusion method. This study was prompted by the lack of precision in the data reported by Borg and Birchenall. Knudsen cells used during this study were fabricated from 0.020-in.-thick tantalum tubing. The tops and bottoms of the cells were cut from 0.010-in.-thick tantalum sheet, press-fitted, and welded in place. The orifice was drilled in the cell top and subsequently reamed to a knife-edge thickness. The diameter of the orifice was measured with a traveling microscope capable of reading 0.0001 cm. The sample was heated by means of a resistance

Jan 1, 1967

By Robert D. Pehlke, Robert G. Blossey

The solubility of nitrogen in liquid binary and ternary Fe-Ni-Co alloys has been measured by the Sieverts' method between 1550°and 1700°C. Solubility data and standard free energzes and enthalpies of solution for nitrogen in the alloys are presented. Interaction parameters are discussed and presented for binary and ternary alloys. MOST of the studies of nitrogen solubility in liquid metals have been directed toward the dilute alloys of iron. Several of these investigations have included measurements of the nitrogen solubility in Fe-Ni al10s'- and in Fe-Co alloys.435 There has been some work, however, that has extended across the e-i-" and F-CO" binaries. This investigation was undertaken to determine the nitrogen solubility in both binary and ternary alloys of the Fe-Ni-Co system. It was also hoped that the differences between earlier studies might be resolved. EXPERIMENTAL METHOD This investigation was made using a Sieverts' apparatus described previously." The nickel (99.85 pct) and cobalt (99.9 pct) were obtained from Sherritt-Gordon Mines, Ltd., and the iron (99.95 pct) was Fer-rovac-E obtained from Crucible Steel Co. Recrystal-lized alumina crucibles were used throughout the entire investigation with no evidence of crucible-melt reaction. Melt temperatures were measured with an optical pyrometer and the temperature scale calibrated against the melting points of the three pure metals. The emissivity of the melt was assumed to be a linear function of composition for all alloys, as has been shown for Fe-Ni alloys.lZ The emissivity of the pure metals at 1600°C were taken as 0.43 for iron, 0.44 for cobalt, and 0.45 for nickel. Using these emissivities, the trans mis sivity of the system was found to be 0.51 i 0.01. The Sieverts' method was used for this study and followed the procedures outlined previously.l' The individual metals were weighed to give about 100 g of alloy. The alloys were melted in the crucible under a partial pressure of argon. The system was evacuated, and the "hot volume" was measured with argon. To avoid the errors caused by vaporization, the melt was held under vacuum only long enough to ensure that all of the gas in the system had been removed. The influence of any small amount of vaporization on the "hot volume" was shown to be negligible by measuring the "hot volume" after a run. This measurement agreed with that made at the start of the run within the implicit error, 0.2 cc, caused by the limitations in accurately reading the buret. The solubility-pressure relationship was measured in the pure metals and in several alloy compositions throughout the ternary system. These measurements were made by admitting measured amounts of nitrogen to the system, and then determining the equilibrium nitrogen pressure above the melt. This method has the distinct advantage of higher accuracy, particularly at lower pressures, than measurements made by withdrawing gas from the system to reduce the pressure after determining the solubility at 1 atm nitrogen pressure. This latter method has a practical lower limit of about 0.4 atm where an increased error is encountered because the buret must be emptied to permit further measurements at lower pressures. By determining the relation between apparent solubility and pressure, it was possible to make a good estimate of the initial nitrogen content of the metal from the intercept of the solubility curve extrapolated to zero pressure.11 DISCUSSION The solubility data corrected to 1 atm nitrogen pressure are summarized in Table I. The reported solubility has been corrected for the initial nitrogen content of the alloys. The initial nitrogen contents fell between 0.0002 and 0.0010 wt pct, and were lower in the iron and nickel than in the cobalt. Sieverts' law was obeyed in all alloys at pressures up to 1 atm. Examples of this behavior are shown in Fig. 1. The reaction for solution of nitrogen is Taking the standard state as 1 wt pct N in the alloy and the reference state as nitrogen at infinite dilution in the alloy, and noting the adherence to Sieverts' law, K becomes the solubility of nitrogen in the alloy at 1 atm pressure. Thus the solubility data of Table I were used directly to calculate the standard free energy for the solution reaction. These results are also presented in Table I. The enthalpy of solution is also summarized in Table I as calculated from a form of the van't Hoff relation: Iron-Nickel System. The data for the solubility of nitrogen in liquid Fe-Ni binary alloys is presented in Fig. 2 along the with data of aito, Schenck et al.,' and Humbert and 1liott.l' The data for studies of nitrogen solubility in Fe-Ni alloys containing less than 20 pc t i'- are not presented in Fig. 2, although they are in good agreement with the present work. The results of this study are in good agreement with Schenck

Jan 1, 1967

By P. H. Turnock, R. D. Pehlke

The effects of mutual interactions between elements on the solubility of nitrogen in liquid iron alloys containing chrormium, columbium, molybdenurn, nickel, or silicon have been determined. The equilibrium nitrogen solubilities in the liquid iron alloys were measured by the Sieverts method. The second-order effects caused by the presence of chrormium, columbium , or silicon in the melt were found to be significant. The solubility of nitrogen in liquid iron alloys containing several alloying elements has also been measured as a function of melt temperature and nitrogen pressure. The heat of solution of nitrogen in microcomponent iron alloys has been found to be a function of the logarithnz of the activity coefficient of nitrogen, irrvespectilje of the composition of the melt. The heat of solution of nitrogen in pure liquid iron was determined to be 1265 ± 450 cal per g-atom of N over the temperatxue range 1600° to 1800°. Sieverts ' law was obeyed for all melt compositions studied in the pressure interval 0.4 to 1.0 atm. The solubility of nitrogen in liquid pure iron and in many dilute binary liquid-iron alloys has been the subject of many investigations. Pehlke and Elliott' made a comprehensive investigation on this subject in which they summarized and compared previous researches. However, the practical application of these solubility studies requires prediction of the nitrogen solubility in the multicomponent alloys encountered in operating practice. The interaction parameter as defined by wagner2 has been used to predict the behavior of a solute in a complex alloy, and a modification of this approach has met with reasonable success in several instances.'1"5 The necessity for extending the nitrogen solubility data on binary alloys is caused by the lack of direct measurements of the solubility of nitrogen in molten alloy steels. A direct comparison between measured solubilities and those predicted for multicomponent alloys based on data in binary systems has been made in only a few instances, and most of these were reviewed by Langenberg,6 who developed a graphical technique for predicting nitrogen solubilities in multicomponent iron alloys. The solubility of nitrogen has also been studied over the entire Fe-Cr-Ni ternary system by Humbert and Elliott.? Both studies compared the solubilities computed from binary iron alloy data with those measured in ternary alloys in the liquid state at 1600°C. Most of the nitrogen solubility measurements referred to above were for iron alloys at 1600°C; thus, the ability to predict nitrogen solubilities in molten iron alloys has been restricted primarily to alloys at 1600°C. Recently, Nelsson8 devised an approximate method for calculating the change in nitrogen solubility in molten iron alloys as a function of temperature, but an assumption of regular solution behavior limits the applicability of the method. Chipman and Corrigan9,10 have developed an empirical correlation. based on the activity coefficient of nitrogen in the iron alloy at 1600°C, which facilitates the estimation of nitrogen solubilities at higher temperatures. This method also has limitations, due to the necessity of calculating the activity coefficient for nitrogen in a multicomponent iron alloy at 1600°C from the nitrogen solubility data for binary iron alloys. The shortcoming of such a straightforward approach to the problem of predicting nitrogen solubilities is the disregard of mutual interactions between elements in a complex iron melt. This investigation was conducted in an attempt to provide a more reliable method of predicting nitrogen solubilities in multicomponent iron alloys. The effects of the mutual interactions between chromium, nickel, silicon, molybdenum, or columbium in iron were studied, using the Sieverts' technique1,7 to measure the effects of alloy composition, temperature, and pressure on the solubility of nitrogen in ternary liquid iron alloys.

Jan 1, 1967

By C. S. Yust, C. S. Morgan

ThIS note reports the observation of masses of dislocation etch pits around the weld necks of small single-crystal particles of calcium fluoride sintered to a cleaved face of a larger CaFz crystal. Crystal particles in the -50 +I00 mesh size range were placed on freshly cleaved CaFz surfaces and heated at 1250°C for 30 min in a tantalum container in an argon atmosphere. The sintered specimens were then etched at room temperature for 40 to 50 min in a 2 pct sulfamic acid solution which is a selective etch for dislocations in caF2.' Figs. 1 through 3 show the masses of dislocation etch pits observed around weld necks after etching. In some cases, particles were gone after removal of the specimens from the furnace although weld necks were readily visible. In other instances, no etch pits formed around a weld neck. A possible cause of concentrations of dislocations on the crystal surface is mechanical deformation of the base crystal when particles are dropped on it. If such a deformation does occur, it would be much smaller than that caused by the light punching of a crystal with a sharp instrument which results in large concentrations of etch pits. However, crystals deformed by punching with the sharp instrument and annealed at the conditions of these experiments (1250°C for 30 min) before etching showed no concentrations of dislocation etch pits. It is obvious that dislocations from the much smaller deformations, possibly created when particles are placed on the surface, would also anneal out. Etching of large crystals which had particles placed on them in the usual manner but which were not heated showed no dislocation concentrations such as shown in Fig. 1. The magnitude of dislocation etch-pit concentrations did not vary with extensive variation of the cooling rate. The appearance of many of the etch-pit clusters is typical of a well-annealed condition, indicating that the dislocation concentrations formed before the specimen temperature was lowered. Therefore, it is evident that thermal stresses in the neck area did not create the deformation indicated by the presence of the dislocations. The possibility exists that the etch-pit concentrations at places where particles had been removed may be the result of deformation accompanying the fracture of the sintered bond. That this is not so was demonstrated by breaking off particles around which no etch pits occurred. Re-etching never resulted in the large concentrations observed at sintering sites. The stress available to effect material movement during sintering of two particles will depend on the geometry at the contact point but can easily exceed the macroscopic yield stress in CaFz systems. It appears that the plastic deformation observed results from sintering or simply from the weight of the small particles. It has been previously argued that plastic flow makes an important contribution to the initial densification of oxides having the fluorite crystal structure.2p3 If plastic deformation occurs, it would begin as soon as the temperature is sufficiently high

Jan 1, 1967

By G. S. Baker, S. H. Carpenter

Langenecker has reported significant reduction in strength of high-strength metals during ultrasonic t'ibration. Decreases in static yield stress an order of magnitude greater than the calculated stress amplitude of vibrations were reported by him for a stainless steel and for tungsten. in the present work, attempts were nzadc to verify such large reductions in yield and flats stresses using resonant librations of measured amplitudes. The results show that both the soft metals (copper and aluminum) and the high-strength metals (sleels) hare reductions in yield and .flow stresses no larger than the stress amplitude of libration. BLAHA and Langenecker,' investigating the effect of vibratory stresses on the deformation of zinc and aluminum, found a decrease in the static yield and flow stresses approximately equal to the vibratory stress imposed. Langenecker later extending this work to high-strength metals such as stainless steels and tungsten2 found a much larger effect. In these metals the static yield and flow stresses decreased by an amount more than an order of magnitude greater than the calculated vibratory stresses. It was suggested that this phenomenon could be a serious hazard to high-strength structures in an acoustic environment, such as a large rocket at launch, or could be used advantageously in the working of hard-to-work materials such as the refractory metals. Langenecker and others3 have investigated the effect of high-amplitude vibrations on many metal-forming operations. The results have been quite favorable with usually a large decrease in the energy necessary for the forming operation. The processes, however, involve large frictional forces and it is not clear whether the decreases in forming forces are to be ascribed to decreased friction or to decreased flow stresses. The present paper reports an attempt to determine the effect of accurately known vibratory stresses on the static yield and flow stresses. I) EXPERIMENTAL TECHNIQUE The standard multicomponent resonator technique for measuring internal friction has been adapted to allow simultaneous high-amplitude vibration, internal-friction measurement, and tensile deformation. This has been described in detail elsewhere.4 Longitudinal oscillations of approximately 50 kc frequency are excited in a multicomponent resonator by a quartz transducer. A second transducer measures the amplitude of vibrations. Fig. 1 shows a schematic drawing of the resonator and grip arrangement and the displacement pattern produced. Since the centers of the dummy bars are at displacement nodes, they represent points where attachments will not materially affect the vibrations. The force is applied by a standard Instron tester. The sample may be deformed while simultaneously vibrating at up to 104 strain amplitude. 11) EXPERIMENTAL RESULTS The effect of high-amplitude vibrations on the yield and flow stresses of copper. aluminum, tantalum. a soft iron, and a stainless steel has been measured. In addition samples of tungsten vibrating at stress levels up to 10' dynes per sq cm have been subjected to static stresses near the static yield stress with no indication of macroscopic deformation. Fig. 2 gives typical results for 99.999 pct polycrys-talline copper. A vibratory stress of 7 x 107 dynes per sq cm is applied at points "a" and removed at points "h". The behavior of aluminum is identical. In agree-

Jan 1, 1967

By Eugene S. Machlin

A classical theory of solid solutions involving neavest-nergkbor intevactions with both central and linked-central forces between atoms has been developed. It has been found that the theory, where it can be checked quantitatively, is in ageement with experiment. The theory encompasses a description of many diverse pkenomena, such as antiphase shift structures, size effect, relative stabilities of various solutions, lattice para,neters, and order-disorder transitions. In particulav. a quantitative prediction not involving adjustable pavameters is made concevning the deviation of the Au-Cu interatonlic distance in long-range ordered (Ll,) Cu-Au I fronl the average distance based on the distances in pure gold and copper. This prediction, which is in agreement with expel-intent, has not been encompassed by any preuious theory. The theory of order-disorder is fragmentary. That is, no one theory exists that can explain the variety of qualitative phenomena observed. Further, many theories are not in good quantitative agreement with experiment. This subject has been reviewed by Muto and Takagi, Tuttman, and Oriani.3 There exists no doubt that the quasi-chemical approximation is not a complete description and that the inclusion of strain energy using macroscopic elasticity theory concepts leads to results in disagreement with experimenL4 The observation of antiphase domains and ordering systems such as Cu-Pt has led to Brillouin zone treat-ment of the order-disorder transition as opposed to the classical Ising model. The objective of this paper is to demonstrate that it is possible to develop a pairwise approximation model that can explain many of the observed order-disorder phenomena that have puzzled investigators in the past. This theory is based upon an empirical model due to ergmman' for the elastic constants of metals. This model is generalized for multicomponent systems. As will be shown, the theory yields a short-range ordering energy for the disordered solution which differs from the ordering energy calculated from the differences in energy of disordered and long-range ordered solutions. It will be demonstrated that there is no necessary correlation between heats of formation and the tendency to order or between size effect and the tendency to order. Also, the existence of antiphase domains and iso-short-range-order systems that form superlattices (Cu-Pt) is predicted on the basis of the theory. Further, the relative stability of competing superlattices is calculable from the theory. If single-crystal elastic-moduli data are available for the pure components and one superlattice then there exists but one adjustable parameter in the calculation of lattice parameters for both the disordered and ordered solid solutions. In one special case, no adjustable parameters are required and a quantitative prediction is made. For the calculation of energies and partial order, there exists but one additional adjustable parameter, the pair-exchange energy V used in the quasi-chemical approximation (or the Ising model.) However, in these calculations, much more precise values are required for the single-crystal elastic moduli than available if the quantitative uncertainties in the predicted values of the energies are to be sufficiently small. THEORY ~er~man' has developed a model with which he was able to obtain fair agreement with experiment for the relations between the elastic constants for metals. This model which we shall call Bergman's model is a linear combination of his models I and 11. In effect, Bergman, in this model, considers that each interatomic distortion is composed of two components: a classical central force distortion with an associated central force constant and what we shall call a linked-central force distortion with an associated linked central-force constant. The linked-central force distortion component obeys the constraint that the sum of such distortions over all the bonds equals zero. No constraint is imposed on the classical central force distortion component. Bergman' derives the constraint on the linked-central force distortion on the basis of application of Pauling's relation between bond distortion and bond number to metals.ga This assumption is not logically necessary, however, and the Bergman model may be taken as a mathematical model for elastic constants, e.g., a purely empirical model without a physical basis. In the present work, the method of Bergman has been applied to two-component systems (solid solutions). In place of an external strain—which would allow a calculation of the elastic constants for the two-component system—it is considered that internal interatomic distortions exist as a consequence of having three potentially unequal distortion-free interatomic distances and but one "average" interatomic distance. It is assumed that the distortion-free interatomic distances between atoms of the same element are those found in the pure element having the same undistorted crystal structure as the solid solution. The distortion-free interatomic distance between unlike atoms is in general not measurable except in the probably nonexistent

Jan 1, 1967

Jan 1, 1967

By Leonard Obert

Before 1957 a number of investigators reported stress determinations made on or near the surface of underground excavations. The usual procedure was to measure surface strains and to calculate the stresses using laboratory-determined values of the elastic constants of the rock. In some instances strain gages were stress-relieved so that the measured stress was absolute. Also, several investigators reported near-surface absolute stress determinations made by the flat-jack procedure. In 1958, Hast1 described a procedure for making absolute stress determinations within a body of rock. In this procedure a diametral deformation gage was placed in a borehole and then the borehole was overcored to produce stress relief. The secondary principal stresses in the plane normal to the axis of the borehole were calculated from measured deformations and the elastic constants of the rock. During the past nine years a number of investigations have been reported1-20 in which this technique, or modifications of it, have been reported. Both the stress distribution in the walls of underground openings and the stress field at points as great as 200 ft from these openings have been determined. Considered collectively, these reports shed some light on the nature of the stress distributions in the proximity of underground openings and on the stress field, that is, the state of stress outside of the zone of influence created by openings. To summarize these findings first consider the stress distribution in the wall and structural components of openings. Fig. 1 (a) shows a typical theoretical stress distribution curve in a linear-elastic, isotropic, homogeneous material. Fig. 1 (b) is an idealized measured stress distribution curve for the same opening in a relatively unfractured uniform, but brittle,

Jan 1, 1967

By H. Majima, E. Peters

The oxidation rates of pyrite, pyrrhotite, chalcopy-rite, chalcocite, covellite, bortzite, galem, sphalerite, and stibnite have beet2 carefully compared at 120 oC, using aqueous phosphate solutions buffered at pH 2.7, 7.1, and 11.2 as zvell as in 1.0 M NaOH and in am~onia-containing solutions. Under conditions of these studies, variations in rates of more than a factor of two per unit of mineral surface area were not observed for different minerals in phosphate buffered solutions, except that pyrrhotite showed unusually rapid oxidation rates In acid solutions, and stibnite showed very rapid oxidation rates in basic solutions. In caustic solutions, oxidation vates varied considerably, the most rapid being for pyrite and the slowest for sphalerite. In the presence of ammonia, only copper minerals showed more vapid oxidation rates in neutral solutions. Oxidation rates were measured on the basis of oxygen-consunzption rates per unit surface area of exposed mineral, using equivalent surface areas, mineral mesh sizes, pulp densities, agitation, and oxygen pressure. OXIDIZING pressure leaching of sulfide minerals has been a commercial method of treating concentrates of nickel, cobalt, and copper for over a decade, and recently the treatment of lead and zinc concentrates,' and even the recovery of sulfur from pyrrhotite by such processes, have been shown to be technically feasible.' Furthermore, the leaching of uranium ores by solutions acidified through the oxidation of pyrite and other sulfides present in the ore is commercially practicable.3 5 The mechanisms by which sulfide minerals oxidize in aqueous environments are not yet understood. However, certain generalities can be made for systems containing no unusual reagents, in which oxygen is the oxidizing agent. In acid solutions the oxidation of many sulfide minerals leads to the formation of elemental sulfur.8'7 The attack of some sulfides, notably galena (PbS), sphalerite (ZnS), and pyrrhotite (FeS), at temperatures below about 110°C leads to an almost quantitative conversion of the sulfide mineral to elemental sulfur according to the equation: On the other hand pyrite (FeS2) and copper minerals do not yield elemental sulfur quantitatively. Not more than 50 pct of the sulfur in pyrite is converted to the elemental form in acid oxidation, and this percentage is lowered by higher temperatures and possibly higher oxygen pressures.8'9 Copper minerals sometimes yield elemental sulfurlo'" but, since sulfur can reduce cupric ions with the precipitation of CuS or Cu2S, it is not likely that elemental sulfur is obtained in good yield. In acid solutions sulfur that is not converted to the elemental form always appears as sulfate salts or sulfuric acid. Sulfide minerals that yield elemental sulfur nearly quantitatively on oxidation in acid solutions tend to generate H2S when the conditions are not oxidizing. However, although it has been suggested that H2S is an essential intermediate in the mechanism of oxidation," this is doubtful because it is oxidized very slowly by oxygen. In basic solutions elemental sulfur is never formed, as predicted by thermodynamical considerations, summarized in the form of a potential-pH diagram in Fig. 1. However in neutral and basic solutions, unstable forms of sulfur not shown in the diagram appear during oxidation, notably thiosulfate (SOT-) and polythi-onates (S,O;-, x = 2 to 6).l3,l4 On prolonged oxidation only hexavalent sulfur as sulfate (SOi-) or sulfamate (NHzSO;) is found to remain, the latter appearing only in the presence of ammonia. The oxidation kinetics for thiosulfate by oxygen are the subject of a separate paper,'5 and were studied on the presumption that thiosulfate may, in fact, be a primary oxidation product for sulfide minerals, at least in neutral and basic solutions. A survey of the literature indicated that comparative oxidation rates for different sulfide minerals were needed to establish the role of the mineral structure and its thermodynamic properties on the oxidation rates and mechanisms.

Jan 1, 1967

By L. A. Weitzenkamp, N. M. Bashara

A study of the electrical conductivity of gold films less than 200 in thickness indicates a negative temperature coefficient of resistance and a thermal actiuatlon energy of less than 0.25 ev. The films consist of discrete metal islands of linear dimensions from a few angstroms to 1000A. Films were able to withstand applied fields up to 60,000 v per cm before breakdown occurred. A model for the conduction mechanism is proposed which involtes a Potential barrier due to work junction, irriage forces , and an electrostatic potential arising from separating an electron from a neutral island leaving behind a positively charged metal island. Activation energies of less than 0.25 ev ave consistent with this model, which includes a tunneling andor Thermal mechanism for conduction between the separate metal islands. An apparent satuvation effect in conductivity at high fields is observed experimentally. The saturation effect may be explained by the influence of the electrostatic contribution to the potential barriers for the transition through several islands adjacent to the original island which was activated to give up an electron. The proposed model gives Poor quantitative agyeement for the intermal electrical field between islands. ThIS paper will relate the structure of discontinuous metal films to the electrical properties and will emphasize the following topics: 1) the relation of the conduction mechanism to particle size and a comparison of particle size from electrical measurements with electron-microscope studies; 2) the saturation of the conductivity at high electric fields; and finally, 3) a comparison between the external field applied and the apparent field between particles. che- latter comparison points to a need for a modification in the model for the conduction mechanism first proposed by orter' and expanded by Neugebauer and webb2 which will be dealt with in the discussion. The paper is based on results on gold films on glass microscope slides. The clms were vacuum-evaporated and were about lOOA thick, thickness being measured by interferometry. It has been observed that metal films of this thickness do not exhibit bulk metallic conduction. Films thinner than some critical thiclmess, depending upon substrate temperature and other factors, have conductivities which increase with increasing temperature with thermal activation energies of less than 0.25 ev. Electron-microscope studies3 have shown that these films consist of discrete metal islands having linear dimnsions from a few angstroms to approximately 1000A. When the metal is being vacuum-deposited on the substrate, islands on the order of a few angstroms appear first. As the deposition continues the islands may tend to agglomerate into larger particles and may eventually grow together into a continuous film,3''' In our tests the conductivity of the gold films was found to be about ten orders of magnitude less than the bulk conductivity of gold. When oxygen was introduced into the test chamber the conductivity decreased by a factor of about one-third. This can be related to an increase in work function for gold caused by adsorption of oxygen, as reported by Oullet and Rideal.s Exposure to an atmosphere of water vapor caused an increase in conductivity by a factor of 2 or 3 when a low field was applied. When the films were exposed to water vapor under a high field the conductivity increased by as much as two orders of magnitude. The activation energies measured were much less than the work function for gold, 0.25 ev or less, with the smaller activation energies observed for thicker films. It will be shown that the activation energy is a function of particle size and spacing. In general the model for the potential between metal islands would include the effective work function, the image force, the applied field, and an electrostatic term. The electrostatic contribution arises from the potential required to separate an electron from a conducting sphere. According to Neugebauer and webb2 the maximum potential due to the field and the electrostatic term only is

Jan 1, 1967

Jan 1, 1967

By K. J. Anusavice, R. T. DeHoff, A. G. Guy, T. B. Lindemer

As one oi the approacizes to understanding multicorn-ponent dimsion, an expevinzental sturly is being jnade of tracer diffusion in the copper corner of the CLI-Ni-Zn syste?n, out to 30 at. pct each of nickel and zinc, and in the 150°C range oJ temperature just below tlze solidts te?rlperature. The reslts obtained using the Znm isotope are reported heve, while studies with nickel and copper isotopes are planned for a future paper. The fifteen alloys investigated were melted in sealed wear lubes, sroaged, homogenized, and then analyzed, using the conventional isotope-plating plus lathe- sectiorzing teclzniqlte. The data obtaiued show that the difJusion coeflcient of the zinc isotope increases titlz increase in zinc content, and decreases t'itlz incease in nickel content. The correlation xith solidus temperature is particularly strong. Diffirsiui-ties ranged fro u sq cm per sec nt tlze Iiigh-zinc, low-nickel compositions. The activation energy /or tracer diffusion ravied j.or 31.000 to 54,000 calper mole. It is now generally recognized that diffusion data and theories are needed for multicomponent systems, where extensive practical developments and even some theoretical studies have already been made. For example, much recent work on precipitation from solid solution has been concerned with ternary solid solutions such as A-M-Z' while Zener relaxation has been studied on Au-Ag-Zn alloys,' although adequate diffusion data are available for neither of these systems. Actually, the only ternary systems for which systematic diffusion studies have been begun, in addi- tion to the one reported here, are CO-i-cr3 and Cu-A-Au. Since the theory of multicomponent diffusion is still in the stage of active development5 it is important to distinguish the various kinds of diffusion data that can be determined. An oversimplified approach, widely used prior to 1950, was to determine the influence of a third element, such as nickel, on the diffusion behavior of a binary alloy, such as CU-Z. Later it was recognized7 that four diffusion coefficients can be used to describe ordinary interdiffusion in a ternary system, while as many as six coefficients may be required to include the Kirkendall effect. It is likely that the number of independent coefficients will be shown to be less than four and six, respectively, through the application of the thermodynamics of irreversible processes.5 The simplest type of diffusion in a multicomponent system is tracer diffusion, since each component is characterized by its own tracer-diffusion coefficient in an alloy of a given composition. Thus, in a ternary alloy there are three tracer-diffusion coefficients, each a function of composition and temperature. The present research program is a study of tracer diffusion in the copper corner of the Cu-Ni-Zn system out to 30 at. pct each of Ni and Zn in a 150°C range of temperature just below the solidus temperature. The

Jan 1, 1967

By R. D. Carter

Methods are presented for calculating the performance of multiwell gas reservoirs. These methods account for two-dimensional, unsteady-state flow of a non-ideal gas through a heterogeneous formation. The performance can be obtained for gas reservoirs with known physical properties and configuration subjected to specified development and production schedules. These methods may prove helpful in optimizing the exploitation of gas reservoirs. The numerical solrrtion procedures given for this non-linear problem are extensions of known techniques for the linear diffusion equation. Two of these procedures are based on a new difference equation given by Saul'ev. Limitations and advantages of these procedures are discussed. An example solution is presented and is used to compare the calculation methods. INTRODUCTION Li planning the operation of a multiwell gas reservoir, it is desirable to predict its performance for each alternate development and producing schedule under consideration. This paper presents three numerical procedures that can be used to calculate such gas reservoir performance using a digital computer. These methods account for two-dimensional transient flow of a non-ideal gas within the reservoir. Extension of these methods to three-dimensional flow is possible. The paper is divided into three parts. The first describes the problem for which a solution is wanted and three numerical procedures that can be used to obtain solutions. The second discusses the information necessary to set up a problem. This part will be of greatest interest to the field engineer. The third gives data and results for an example problem. PROBLEM AND SOLUTION METHODS In the following development, a gas reservoir is regarded as a sealed, porous, permeable, heterogeneous body in which a single, non-ideal gas phase is flowing. Flow is permitted in the x- and y-horizontal directions, but is considered to be negligible in the vertical or z-direction. The reservoir can be tapped by one or more wells. Methods to be described provide a basis for calculating the complete performance of the reservoir, including rates and cumulative production from the wells, and pressure distribution and decline in the reservoir. If the isothermal flow of a non-ideal gas obeying Darcy's Law occurs in two dimensions in a region R, the governing equation in this region is:

Jan 1, 1967

By K. M. Rolls, J. Wulff, D. A. Colling

Solid-solution alloys of the Ta- Ti system containing up to 70 at. pct Ti were melted and fabricated into wire. Steady magnetic-field measurements of cold-worked wires at 4.2°K indicate that the resistive critical field increases smoothly with increasing titanium, reaching a maximum of 93 kG (J = 1 amp per sq cm) for a composition of about 50 at. pct Ti. The composition dependence of the resistive critical field indicates it is largely paramagnetically limited for alloys containing more than 35 at. pct Ti. For cold-worked wires the value of the critical current density, Jc , was found to be insensitive to composition changes for compositions in excess of 20 at. pct Ti. It was observed that Jc could be increased by final-size heat treatment at 400°C without altering the value of- the resistive critical field. Experimental data are used to calculate the electronic specific-heat coefficient and the "upper critical field" for the alloys studied. THE effect and importance of metallurgical structure on superconducting properties have been summarized by Livingston and Schadler.1 Specific work on solid-solution alloys such as Nb-zr2-7 and Nb-Ti5-7 have shown that critical current density (Jc) and superconducting transition temperature are structure-sensitive. Berlincourt et al.6,8,9 in their studies of transition-metal alloys find that Ta-Ti alloys remain superconducting at fields comparable to Nb-Ti alloys. 6,8 Transverse critical current tests of a Ta-10 at. pct Ti alloy10 and longitudinal critical current tests of a Ta-25 at. pct Ti alloy1' indicate that such alloys are capable of carrying high currents at intermediate fields (-40 kG). The work reported in the present paper was undertaken to explore the superconducting properties of further compositions in the Ta-Ti alloy system as well as the structure sensitivity of the superconducting properties. I) EXPERIMENTAL PROCEDURE Alloys were prepared by melting tantalum (Fansteel Metallurgical Corp., 99.96 pct purity) and iodide, crystal bar titanium (Foote Mineral Co., 99.92 pct purity) mixtures in an arc furnace on a water-cooled copper hearth using a tungsten electrode. Melting was accomplished in a purified, gettered argon atmosphere at pressures from 250 to 400 Torr. Each alloy was turned and remelted fourteen times to assure complete mixing of tantalum and titanium. Ex- cessive coring in the cast samples was, nevertheless, observed. This was somewhat reduced by annealing in vacuo at 1000°C for 13 hr. The ingots were then machined to 0.250 in. diam, jacketed in Type 304 stainless-steel tubing, and swaged to 0.140 in. diam. They were then drawn to 0.010-in.-diam wire. Alloys containing up to 70 at. pct Ti were readily cold-drawn to wire in this manner. Later experiments showed that oxygen additions up to -3000 ppm could also be cold-worked into wire. Test samples for superconductivity measurements in the 2-in, air-core Bitter solenoids of the M.I.T. National Magnet Laboratory were prepared from 10-in. lengths of 0.010-in.-diam wire, cleaned of residual wire-drawing lubricant. Current contacts were made by clamping clean copper tubing over both No. 18 current lead wire and the ultrasonically indium-tinned ends of the specimen wire.12 Potential leads of No. 32 copper wire were connected to the specimen by ultrasonic soldering in an indium bath. The potential lead separation was about 4 cm, corresponding to the circumference of the Bakelite rod to which the wire was affixed with half-mil Teflon tape. The final specimen configuration is shown in Fig. 1. Specimens were lowered into a liquid helium bath (4.2oK) in a double solenoid dewar and positioned so that the maximum magnetic field was oriented transverse to the wire axis of the gage section. Measurements were made by passing a current through the specimen at a preset solenoidal magnetic field. The current was increased until a 1-pv potential difference appeared across the gage section (1/4 µv per cm). At low magnetic fields, however, it was not possible to use this criterion because power-dissipation difficul-

Jan 1, 1967

By H. C. Chao, W. F. Hosford, L. H. Van Vlack

The negative "plastic Poisson's ratio" suggested in earlier studies of Mus deformation is analyzed, and the results are verified experimentally with NaCl crystals. In the early stages of deformation where the primary {110}(110) slip predominates, compression along. the [001] direction produces contraction along the lateral [011] direction plus a compensating expansion along. the [100] direction. With additional strain, the primary slip is supplemented by secondary {111}(110) slip so that the above contraction diminishes and a more typical deformation appears. THE shape change of bee and fee crystals deformed by compression or tension along [011] has been analyzed in some detail and shown to be responsible for the development of peculiar microstructures in [011] fiber textured polycrystals of these metals.1'3 This paper concerns the unusual shape change accompanying [011] compression of NaCl crystals. It is the direct outgrowth of an earlier investigation of the deformation of manganese sulfide inclusions in steel.3,4 In that investigation, cylindrical specimens of steel containing small oriented crystals of MnS were prepared by powder metallurgy and plastically compressed. The flow of the inclusions was determined relative to that of the steel by sectioning the composite and measuring the length-to-width ratio L/W of the inclusion and diameter-to-height D/H ratio of the steel cylinder on the plane of section. These L/W ratios, normalized by dividing by the initial LO/WO ratio of the inclusion, were compared with the normalized D/H ratio of the steel cylinder. Of particular interest here are the deformation characteristics of an inclusion oriented with [Oil] parallel to the compression axis. When measurements were made on sections parallel to the (100) plane of the inclusion, the L/IV ratios were only slightly in excess of unity, indicating a high apparent hardness of the [011] criented inclusion. However, measurements on a (011) plane of section resulted in L/W ratios which were much larger, Fig. 1. These observations prompted an analysis of the strains resulting from slip in an MnS crystal compressed along [011.]. CRYSTALLOGRAPHIC ANALYSIS Manganese sulfide has the NaCl crystal structure, and the predominant slip system is {110}(110). A secondary system, {111}(110), has also been reported.= {110}(110) Slip. When a crystal is subject to a uni-axial compressive stress 011 along [011], four slip systems, (101)[101.], (101)[101.], (110)[i10], and (110) [ 110], will be equally stressed with a shear stress t = 0.2 011 while the other two {110}( 110) systems will be unstressed. The normal strain En along any reference axis n resulting from slip is given by Schmid's law: en = S COS ?in COS in ?i 111 where ?in and +in are the angles between n and the i slip direction and n and the i slip plane normal, respectively, and where ?i is the shear strain on the i slip system, For the four active slip systems above, the cos ?in cos +in terms are all equal when the reference axes are the [011] compressive axis, [011] and [ 100]. Eq. [I.] therefore reduces to en - cos ?n cos +ny [2] where y =S?i for all slip systems. Substituting the appropriate angles, Eon = 0.25? 110 eon - 0.25y110 [3] €100 = -0.50y 110 The interesting feature of Eqs. [3] is that they predict that the strains in the [011] and [011] directions, resulting from {110}(110) slip, are equal and of the same sign. Thus when a crystal is compressed along [011], it will contract along the lateral [oil] direction

Jan 1, 1967