Search Documents

By Dilip K. Paul, Charles H. Jacoby

The economic importance of salt domes has been recognized throughout the world, primarily because of oil and gas accumulations on their flanks, and to a lesser degree, for the value of their salt and potash. Recently they have become of value as hosts for cavities used to store hydrocarbons. In the near future we believe that their main value will be a source of geothermal energy. Although tremendous effort has been expended on the understanding of the geology and physical characteristics of the strata intruded by salt domes, relatively little energy has been exerted in the comprehension of the salt dome itself. Salt domes have long been recognized as a geological heat anomaly. With respect to other sedimentary rocks, salt is a good conductor of heat. Expressing values in 10-3cgs units, sedimentary rocks vary from 1.0 to 8.0; metamorphic rocks from 5.2 to 8.4 and igneous rocks from 3.1 to 9.8. Rock salt in its pure form has a thermal conductivity of 17. Thus a salt dome can be expected to act as a conduit bringing heat vertically from deep within the earth's crust.

Jan 5, 1974

By C. D. Broadbent

Open pit blasting can be a low cost routine or a high cost bottleneck depending on geology, environment and the operator's ability to master site conditions. Because blasting is a repetitive operation, there should be ample opportunity to optimize the process; but ordinarily this optimization is rarely achieved and then only if conditions remain consistent and predictable. Often, however, and particularly with porphyry coppers, hidden differences in rock characteristics nullify the operator's best efforts. At a porphyry copper deposit being mined by Kennecott Copper Corporation, all of the following rock types occur; oxidized and fresh porphyry, altered and silicified limestone, explosion breccia, rhyolite, sandstone, shale and several others. The units can cover large areas or be limited to a few tens of feet in maximum dimension. They are rarely visible on the bench surface and often do not show up in the bench slope. Even though the blastability of these rocks varies substantially, a generally-uniform blasting pattern was formerly used with disappointing results. Secondary blasting was often required and high bottoms occurred frequently, overblasting wasted drilling time, and explosives caused excessive throw.

Jan 4, 1974

By Duane H. Haley

Dr. F. Well, the first thing that you have to realize is what is the Bureau of Mines? The Bureau of Mines basically has two functions. First it does the research and development relating to mining, processing, conversion, refining, recycling and substitution for minerals and materials. We work hand in hand with the U. S. Geological Survey on the geological end, although the exploration part of the game is theirs, and there is a very good relationship between the Survey and the Bureau of Mines. There are some overlaps with the Office of Coal Research, and we expect to be able to straighten out the areas of overlap, because it's important than OCR and the Bureau work together. Both the Office of Coal Research and the Bureau of Mines will have increased budgets next year, assuming that they are appropriated by the Congress. The other general area is in the whole area of mineral policy. The Bureau of Mines again is the key agency for developing data and analyses and making recommendations on all types of mineral policy in the Federal Government. It's a focal point for all types of minerals activities. It's the only real centralized focal point, along with the USGS, in the whole Federal Government. The problem areas, to answer your question specifically, are first of all the Bureau of Mines budget this year is $105 million and the budget for next year is $215 million, so it's more than double. Now, assuming that this budget is appropriated by the Congress, most of that money will be used for research and development in the energy area.

Jan 4, 1974

By Charles R. Isaacs

In 1972 Kennecott Explorations, Inc. conducted a three month cruise to the central Pacific as part of a study of deep-ocean manganese nodules. One of the objectives of the voyage was to collect at least 200 tons of nodules for use in extractive metallurgy research and various engineering tests. It was determined to cut off production at a maximum of 200 tons, should we reach that amount before the end of the 38 on-station days. We were able to reach that goal; 200 tons of nodules were collected, representing an average return of 2340 lb from 171 dredge runs. Once equipment and techniques were refined, normal returns consistently exceeded 2 tons per haul. Up to this time, Kennecott had sampled extensively with the use of small free-fall devices using wire rope and winch equipment. These devices have never offered a viable method for collecting nodules in bulk, and we sought to develop a dredging capability which would give some assurance of meeting future requirements with efficiency and economy. After testing a series of increasingly complex dredge designs at sea, it was decided to utilize two of the simpler configurations, which after modification provided the basic design for the dredge used.

Jan 4, 1974

By J. M. Donkers, R. de Groot

The various objectives of dredging at sea require different methods and radically different equipment for their optimum fulfillment. In the majority of cases, sea dredging is done by means of dredging equipment connected to a pontoon or ship floating at the surface. As the supporting hull is subject to the influence of waves, swells, currents and wind, the connecting point of the dredging equipment to the hull will generally move relative to the sea bottom with 6° of freedom. The more important hull motions are surge, heave, pitch and roll. Depending on the actual sea and weather conditions and the size of the hull, some of these motions can be so large that dredging equipment of rigid construction (normal or inland dredges) cannot be used. In those cases where mechanical disintegration of the bottom is necessary and where accurate dredging is required, the designer must find a solution for this problem. For cases where the bottom consists of soils that can be handled by plain suction, highly sophisticated dredging equipment such as the trailing suction hopper dredge permit dredging under all but the most severe sea state conditions. This type of dredge picks up the soil from the sea bottom while slowly underway. The drag suction head is fitted on a suction pipe of such flexibility that the supporting ship can carry out all six movements in relation to the draghead (heave, pitch, roll, sway, yaw and surge), while the draghead remains in firm contact with the bottom. The suction pipe is fitted with flexible hoses, a universal hinge, a horizontal hinge, axial turning gland and sliding turning gland with horizontal axis and is suspended flexibly from the ship incorporating swell compensating buffer gear, keeping the wires taut and the draghead bottom contact pressure fairly constant while the dredge moves up and down. Due to the fact that the draghead has a low bottom contact pressure and has little tendency to sink into the bottom, this compensation is not difficult to realize.

Jan 4, 1974

By Arnold J. Rothstein, Raymond Kaufman

A large number of firms and institutions have evaluated possibilities of mining the manganese nodule source, beginning with a major effort in 1957-58. There have been as many as ten commercial firms actively engaged in major programs of engineering and development, including Deepsea Ventures/Tenneco, Hughes Tool Co., Kennecott Copper Corp. and Ocean Resources, Inc. Foreign firms active in the field are International Nickel CO., Sumitomo Group/MITI, AMR (a joint venture of three West German companies-Metallgesell- schaft AG, Preussag and Salzgitter AG), and Societe le Nickel (CNEXO). It is estimated that it will take from 11 to 19 years for the more successful ventures to reach operational levels. Investment Costs and Rates of Return Five different programs, all from public sources, have been studied to analyze dollar figures regarding investment costs and the possible return on these costs. All are based on a unit of production of a million tpy of dry nodules through the processing plant, which is considered the minimum likely capacity. The costs are not always comparable, and with some liberties, have been forced into two categories. The first covers mining and sea-related costs. The second will include the onshore processing and other costs such as administrative and distribution figures. The costs in all cases are for complete ventures extending from prospecting through mining, processing and distribution of several metals and other products derived from the nodules. All costs are joint product costs, making certain comparisons with land mining difficult.

Jan 4, 1974

By James N. Gundersen

Geological Engineering can be all-encompassing and it necessarily overlaps many applications of economic and applied geology. Other review articles will cover specific developments in rock mechanics, open-pit and underground mining, geology, geochemistry, geophysics and geohydrology- all of which overlap many fields of economic and applied geology. Nevertheless, there still remains a diversity of new and innovative applications of geology to engineering works through the activities of federal and state agencies, college and university departments, and industrial or consultant firms-particularly with respect to the properties of earth materials and their behavior "as-is" in nature or under the stress of engineering works. Governmental Agencies: Federal John T. McGill (Chief: Engineering Geology Branch; USGS, Denver) relates that recently the Engineering Geology Branch, together with several other branches of the Office of Environmental Geology, has undertaken the production of interpretive maps of unusual character. These maps are commonly called special-purpose or single concept maps. A folio, or series of maps, is prepared for each topographic quadrangle or area selected for study. The individual maps in a given series are printed on standard-size sheets so that they can be bound together if desired.

Jan 3, 1974

By Maureen G. Johnson

At least three million ounces of placer gold has been mined from hundreds of deposits in the Southwest since the 1600's. Nevada, the most productive state, produced about 1,700,000 oz. Most of the placers are in accumulations of unsorted, coarse, angular gravel in gullies, dry washes, and on hill- sides. The gold is mixed with debris from the adjacent bedrock and is typically concentrated at or near bedrock or on clay layers or caliche-cemented gravels above bedrock. The most extensive and productive placers are thick accumulations of debris in well-defined stream or gully channels, in alluvial fans at the edges of the range fronts, or as thick residuum on hillsides. With very few exceptions, the gold has been transported only a very short distance from the source. Numerous small high-grade gold-quartz veinlets, rather than single large lode deposits, are by far the most common source of placer gold. Most placer mining consisted of small-scale one-or two-man operations using rockers, pans, and sluices when water was available and dry-washing machines when it was not. Where gravels were deep the miner would dig shafts to bedrock and drift along the paystreak. Large-scale operations in the major districts utilized floating or stationary dredges or, more rarely, hydraulicking to mine extensive deposits. An adequate supply of water for efficient concentration of gold has always been a major problem in the Southwest. To overcome this problem, difficult and sometimes ingenious techniques were used-pipelines to carry water for miles to the placer area were constructed, or gravel was hauled to central washing plants where water was available; numerous designs of dry-washing machines were invented. In some districts, attempts to mine the gravels by large- scale operations failed because the gravels were too wet for dry concentration methods, and no water was available for wet methods; or, when water was available, the gravels were too porous to retain sufficient water in the dredging pond.

Jan 3, 1974

By Constantine Michalopoulos, Roger C. Van Tassel

Commercial demand for gold in the United States is important. It has a large impact on the total world commercial and overall non-monetary demand. Given the present free market price and our need to import gold, it has a substantial adverse effect upon our international payments position. But, according to most recent estimates, the United States demand is perhaps no more than 20% of the world as a whole. In 1971, United States consumption was estimated at 215.6 tons out of a total of 1,412.1 tons 1. This figure is very close to the 16% figure developed by Consolidated Gold Fields as the average for the years 1968-1970.2 Surveys of both production and use of gold on a world-wide basis are not new. With the bulk of gold production in only a few countries, it has been possible to develop fairly reliable series on gold output. Estimates have been developed on the known reserves of gold and probable output at various prices.3 On the demand side, figures have been somewhat less complete and reliable. The Bank for International Settlements and the Director of the United States Mint have regularly published estimates of commercial use in major industrial countries. The IMF has issued an increasingly comprehensive survey in its Annual Reports. The IMF has attempted to cover all nations-not restricting its efforts to major industrial nations-and has tried to estimate both gold taken for commercial uses (Estimated Industrial and Artistic Use) and for private hoarding. Their method is to begin with data on free world output plus any net sales by the Soviet Union, subtract any additions to world monetary stocks (or add to available supply for any net reductions in world monetary stocks), subtract estimates for commercial demand and have left as a residual an estimate for private hoarding. The method is straightforward and simple but the quality of the data is suspect. Industry sources tend to believe the figures as biased on the low side because of a persistent tendency to underreport gold movements.4

Jan 3, 1974

By Thomas Connolly

The Homestake Mine is situated in the northern portion of the Black Hills of South Dakota in a series of steeply dipping and highly folded Precambrian Rocks. The ore bodies are localized along plunging anticlinal and synclinal folds which are locally called "ledges." The gold bearing ore is confined mainly in the Homestake formation which is an iron-magnesium carbonate series of rocks. The individual ore bodies are pipe or lense-shaped zones which plunge 30º to 75º from the horizontal. These ore bodies range from 10 to 100 feet wide and 50 to 400 feet along the strike. Gold values are erratically distributed in a gangue consisting of cummingtonite schist, sideroplesite schist, quartz, pyrrhotite, arsenopyrite, chlorite schist and ankerite. Usually the ore bodies dip at 70° to 80º and often have folded shapes like "fish hooks" or "troughs." Ore grades must be determined by extensive sampling and all mining is based on assay control.

Jan 3, 1974

Would you give us a short biographical sketch including your birthplace, education and current activities? I was born Jan. 16, 1920 in Minneapolis, Minnesota, and lived there the first 22 years of my life. I also spent quite a bit of time on a farm about fifty miles north of Minneapolis owned by relatives. During the Depression, we lived off of ten cows and about fifty chickens. I'm a full-blooded Swede all along the line, and I'll be the last one in my family since my wife is not of Swedish descent. I attended Macalester College, a small school in St. Paul, to study for the ministry originally. However I soon realized that I really didn't have the talents for the ministry and I could probably do as much or more in a field where I did have some talent.

Jan 3, 1974

By James E. Adler, Timothy C. Richmond

The Stillwater District is located in south central Montana approximately 75 miles southwest of Billings, the state's largest city. It lies along the northeast front of the Beartooth Mountains and is within the boundaries of the Custer and Galatin National Forests. The first white visitors in the district were the early trappers, who were soon followed by the prospectors. These early prospectors were drawn to the area by gold and silver discoveries at Cooke City in 1870 as well as by the large gossan formation in Verdigris Creek near the west bank of the Stillwater River and by several scattered smaller gossan exposures throughout the area. The first patented mining claims were recorded in September, 1886.

Jan 3, 1974

By R. W. Vander Laan

Conneaut has a long and illustrious history as a major Great Lakes port for coal and iron ore. The first dock was built in 1892 for unloading iron ore from the Mesabi Range for shipment to the Pittsburgh steel mills via the Shenango & Lake Erie Railroad, later to become the Bessemer & Lake Erie Railroad. The Pittsburgh & Conneaut Dock Company was incorporated in 1893. The world's first Hulett automatic ore unloader was constructed at Conneaut in 1899. Steam operated, it was the model for the giant electric Huletts used today, named after its inventor, George Hulett, who was a Conneaut resident.

Jan 3, 1974

By A. T. Yu

The energy crisis and the resurgence of mining activities highlighted 1972-73. Added to the impetus for more effective materials handling systems has been the continued upward trend of inflation and labor costs. The need for addressing the fundamentals has led to the trend toward an overall systems approach to materials handling problems.1 The decision to move forward with large mining ventures such as the $150 million Hibbing taconite comple2 and the immense Carajas iron project must base themselves on indepth studies of a host of factors viewed in the context of an integral mine-transport-market system. What's important is that each ton of pellet or ore must be an economical commodity at the end users' furnace. The project can still be viaable even if certain components in the entire network appear to be individually costly.

Jan 2, 1974

By A. L. Holmes

Significant technologic advances were made in open pit mining during 1973. The industry faced mounting problems on one front where expansion of stripping activities encountered enlarged public resistance and on another where manpower and materials were in short supply. These challenges, along with the challenge and opportunity to meet the increased demand for mining products including materials for energy production, placed a premium on technical developments and their application. The demands on technology also included the providing of facilities and methods to economically extract minerals from deposits of lower grade, lesser accessibility, and where other uses of land approached the value of its minerals. Detection of Failures in Slope Walls The Bureau of Mines has undertaken research directed towards providing a mine operator with the opportunity to take corrective action before a potential slide becomes a problem.

Jan 2, 1974

By Martial P. Corriveau

Almost everyone agrees that coal and oil shale are the only fossil fuel resources in which the United States is self-sufficient. Of the two, only coal has a technology sufficiently developed to be of intermediate term benefit. Since it takes at least 20 years to bring advanced technology into practice, it seems logical that the major focus on energy developments should be aimed at coal. Meanwhile, we need to trade-off between actions to meet our immediate needs and the various political regulations and social demands that are disrupting the coal industry and the industries dependent upon it. The largest single user of coal is the electric power generation industry. Over 300 million tons of coal are presently being consumed each year. In view of the 5-to 7-years lead time to bring in a base-load fossil-fuel fired generating station, our requirements for double this tonnage in 1980 are already well forecast; that is, if the coal companies are allowed to mine and the utilities are allowed to burn the coal.

Jan 2, 1974

By Stanley Lefond

Industrial Minerals, often called the Cinderella Minerals or the Building Blocks of industry continued their growth patterns through 1973, although profits were slightly lower due to the cost-price squeeze. Most of the individual reports which follow indicate growth rates of 3-15%. Surprisingly such commodities as sulfur held firm in spite of the over supply in the Canadian gas fields; cement was in short supply while the asbestos industry reported a worldwide shortage of group 4 and 5 fibers. Talc and perlite production set new records. In synopsis, 1973 was a productive year for industrial minerals. However 1974 onward appears to be one of contradiction. The unsettled conditions of world economics, the energy shortage, compounded by the Arabs oil embargo have created great problems for all industries. The high energy consuming segments of the Industrial Minerals field will be under intense pressures. On the other hand limestone, lime and perhaps trona, nahcolite might be consumed in ever increasing tonnages in SO2 removal systems connected with smelters and coal-fired power stations. The effects of the proposed changes in the staking, claiming and exploitation of federal lands by the BLM may also have serious repercussions not only to the industrial minerals field but to the entire mining industry. 1974-1975 will certainly be ear-marked as a year of frustrations and difficult decisions.

Jan 2, 1974

By Vanderlei Beisiegel, Arthur L. Bernardelli, Arthur W. Ruff, John H. Tremaine

Estimated reserves of high-grade iron ore at Serra dos Carajás total 16 billion metric tons and have an average grade of 66.7 per cent iron, 2.2 per cent combined silica and alumina, and 0.05 per cent phosphorous on a dry basis. Hematite is predominant and no significant sulfur on other deleterious elements are present. Serra dos Carajás is located in northern Brazil, about 550 kilometers southwest of Belém, Pará. It is six degrees south of the equator between the Xingu and Tocantins Rivers. Both rivers flow northward toward the Amazon River. The greater part of the area is covered by thick jungle, and the most practical means of access is by air.

Jan 1, 1974

By John E. Caffrey

The Federal Coal Mine Health and Safety Act of 1969, Title III, Interim Mandatory Safety Standards for Underground Coal Mines, is devoted to protection of workmen from hazards of electricity, roof, ribs, fire, and explosions. The Rules and Regulations, promulgated through the Federal Register, provide the criteria by which the law would be administered. Certain aspects of the law involve features that could be summarized under entrapment. These are sections 303 (y)(1), (y)(2) and 317 (f) (4). This paper is intended through the use of the figures to describe how these features of the law affect mine ventilation design, what are the problems, and possible solutions to them.

Jan 1, 1974

By G. J. Armstrong, K. S. Lynch, C. G. Thomas, L. A. Baker, R. J. Cornelius

The presence of geothite in a hematite ore has been shown to strongly affect the time of heating to the firing temperature. The investigation of spalling of single pellets and of packed beds has enabled free water and goethite spalling to be identified as separate phenomena. In addition, it has been shown that even for an 18-in. deep bed of green balls, the free water and goethite drying periods can be considered separately. Based on this observation, a method of predicting production rate and hood temperature profile is presented. The method required knowledge of the ore goethite content, ore grind, and the green pellet bulk density. Laboratory results were found to be in good agreement with actual plant practice and have led to improved process performance.

Jan 1, 1974