Search Documents

By H. E. T. Haultain

The study of rock crushing or grinding in tube-mills is difficult on account of the large size of the units employed in the field and the large number of variables entering into the problem. Three or four years ago, in the laboratory of the Department of Mining Engineering of the University of Toronto, a serious effort was commenced to study the matter under laboratory conditions. Experiments were carried on in a cylindrical tube-mill 18 in. long and 12 in. in diameter, inside measurements,

Jan 1, 1923

By F. C. Dyer, H. E. T. Haultain

There has been much written on ball-mills, but no small amount of the literature is simply the expression of individual opinion without sufficient data. This is no doubt due to the complexity and obscurity of the phenomena involved. The outstanding paper is by E. W. Davis,I superintendent, School of Mines Experiment Station, University of Minnesota, which is based on a large amount of data from careful experiments with full-size apparatus, together with some mathematical philosophy. The entire philosophy is summed up in the equations given; but the present writers question the foundation upon which this philosophy is based. Encouraged by the work of Davis, the authors of this paper continued work they had been doing along this line. At first, photographs were taken of the ends of rods in a small laboratory rod mill. The mill was tilted slightly toward the feed end and the discharge end was removed. The rods remained in the mill long enough to permit good observation and good photography. Later, a mill 24 in. inside the stepped lining was constructed. It consisted of two sheets of plate glass, 1/2 in. apart, set in a cast-iron ring. It was driven by a variable speed motor and was connected to an accurate speedometer (magneto and voltmeter type). In place of balls or rods, cast brass disks were used. These were 3/8 in. thick and varied in diameter from 2 in. down to 3/4 in. Four small projections on each side prevented the disks sticking to the glass when water was used; sometimes steel balls % in. in diameter were added to the load of disks. There was also constructed a 6-in. mill with corrugated linoleum lining and containing a dry load of various sizes of steel balls. The mills were so connected to the motor that the small mill made two revolutions to one of the large mill. Many runs were made with a great variety of materials, including crushed marble, seeds of many kinds, and many mixtures (some wet and

Jan 1, 1923

By A. B. Calhoun

These mines, which belong to the Burma Corporation, Ltd., formerly a London company now incorporated in Rangoon, Burma, are situated in the semi-independent state of Tawng-Peng, one of the small divisions comprising the northern Shan states and erroneously known as part of Upper Burma. Bawdwin is approximately 23' 6' N. latitude and 97" 20' E. longitude, 450 miles north of Rangoon, 169 miles northcast of Mandalay and 50 miles south and west of the Province of Yunnan, China (see Fig. 1). Although the mines were worked by the Chinese during the Ming Dynasty, 1412 A. D., the most extensive operations took place between 1796 and 1851, when the mines contributed largely to the silver market of China. During the reign of Tung Chik, 1868 A. D., they were abandoned partly because of the Mohammedan rebellion in Yunnan, which made life and property insecure, but largely because of the difficulty of operating the mines on account of water and poor ventilation. Since that time practically nothing was done, although the Burmese kings are said to have made several sporadic attempts to work the mines, until 1891 when Europeans were attracted by the great slag dumps (assaying about 40 per cent. lead) which the Chinese had left after extracting the silver. After a railroad and smelter had been built and 200,000 to 300,000 tons of slag smelted for lead, exploration work was started and old workings cleaned out in order to locate the remnants of the orebody that it was supposed the Chinese had left. After two years of most discouraging work, the remains of a large orebody was discovered by the Dead Chinaman Tunnel or what is the 171-ft., or No. 2 level adit. From then on the development was rapid and today the Chinaman is considered one of

Jan 1, 1923

By M. Mathieu

The Rove tunnel is the means by which the canal from Marseilles to the Rhone Riverl penetrates the hills of Nerthe, lying between Mar- seilles harbor and Lake Berre, Fig. 1. The canal will communicate at sea level with both terminals. The original project planned a lock near the village of Marignane; but observations, pursued for more than three years, showed that the water surface gradient would average only 0.015

Jan 1, 1923

By M. W. Ditto

THe conversion of the beehive coke plants, in this country, to byproduct plants has been slow, because the coal supplies were near the centers of the steel industry. With the growth of this industry, especially with its development around Chicago, it became necessary to transport large tonnages of coal from the eastern districts and then convert it into coke. The losses due to transportation costs were partly offset by the value of the byproducts recovered. To save the transportation costs, it was desirable that the coal deposits of Indiana and Illinois be utilized. This coal had always been classified as non-coking; it was also considered unsuitable for the metallurgical field because of the high ash and sulfur contents. The conditions, however, were promising enough to start experimental and development work, which crystallized in the design of the Roberts coke oven. The fundamental features of most coke ovens, with respect to the application of heating gas and the recovery of byproducts, are the same and, in the last few years, the tendency has been toward the better application of heating to the walls, higher thermal efficiency, and, by the control of heating conditions, the increase of byproduct yields. Structural features also have been improved and the use of high-grade refractory material has allowed the use of higher temperatures with the resulting higher rated capacity per oven per day. Great improvements have been made in both recuperators and regenerators, particularly with reference to the individualizing of each oven with respect to its adjacent oven, so that each can be operated as a unit if desired. The highest development of the flue type of oven has been applying individual regenerators for the recovery of waste heat. After some research work, it was found that the high-volatile Illinois coals could be utilized for coke by obtaining the better application and control of the heating conditions in the oven. Most of this high-volatile coal that had been used gave a good coke structure under certain conditions. The fact that coke was occasionally made from this coal, demonstrated the possibiity of making coke from it at all times pro-

Jan 1, 1923

By Jos. Van Ackeren

Although the Siemens regenerator principle was introduced into byproduct coke-oven design about 40 years ago, many problems of construction, and particularly of heat distribution and pressure conditions, have not been fully solved. Heat should be applied to the walls of a coke oven in such a way that the coking of the charge of coal will be completed everywhere at the same time, and at approximately the same temperature. This means that the application of heat should be uniform from the top to the bottom of the coal mass (except for the thin layer at the top that is purposely kept at a somewhat lower temperature to reduce cracking of the byproducts); also that a little more heat must be applied to the coke end than to the pusher end, because the coal mass is a little thicker at that end. As a modern coke oven is about 40 ft. long and 12 ft. high, a real problem is involved in the proper application of heat to the oven walls so as to secure quick coking time (without endangering the walls through local overheating) and produce coke made at a uniform temperature. Design of Ovens In all regenerative ovens, the points of combustion are arranged in duplicate sets, one set operating in one-half the area of the heating wall and the other set alternately operating in the other half. Because of the reversal of the flow of gases, the points of maximum and minimum temperatures are alternately located at the same places, thus preventing dangerous local overheating. The practicability of the principle of reversal of flow seems to have been recognized at an early date, and has been applied with every conceivable flue arrangement, combustion chamber, and means of air and gas supply. To summarize the various principles that have proved useful for the control of oven-wall temperature, the best practice seems to have resulted from the acceptance of the use of vertical flues; the separate supply of air and gas to the base of these flues, with the resulting flame

Jan 1, 1923

By Ralph A. Sherman, John Blizard

The experimental investigation described in this paper was conducted to determine the relative combustibilities of different samples of blastfurnace coke when burned in a current of air in a small furnace. It was undertaken in connection with the work done by Perrottl and Kinney2 on the process of combustion in the blast-furnace hearth.3 Reference is often made to the "combustibility" of coke by blastfurnace men, but exactly what is meant by the term "combustibility" is somewhat vague. Brassert,4 in a paper before a meeting of blastfurnace men in 1914, refers to combustibility as follows: The value of the coke in relation to the heat reactions in the furnace is determined not only by the carbon content but even more so by its combustibility. This, in turn, is governed by its size, the physical and chemical composition of the carbonaceous substance forming the cell walls, and the interior and surface structure of the coke pieces. These properties are, in turn, influenced by the chemical and physical properties of the coals used for coking, the density of the cake of coal in the oven, the coking time, temperature and heat regulation of the ovens, and last, but not least, by the method of quenching, screening and handling the finished coke. What principally concerns the blast furnace is the rate of progression of the combustion, which depends not so much on the chemical analysis as on the physical qualities of the coke. It is this rate of progression that we term combustibility, which is the speed at which the carbon molecules in the coke combine with oxygen under given conditions. In general, what the blast furnace requires is a coke which will burn rapidly and with intensity at the tuyeres, yet which has a sufficiently strong structure and hard surface to resist abrasion and solution by CO2 in the upper part of the stack.

Jan 1, 1923

By G. St. J. Perrot, S. P. Kinney

Consumers of metallurgical coke are agreed that the quality of their fuel plays an important part in the performance of the furnace. Less unanimous agreement is evident when the properties of a desirable coke are discussed or when consideration is made of suitable testing methods by which the worth of a coke for metallurgical purposes may be determined quantitatively. Much has been written of the importance of combustibility as a factor in determining the performance of coke in the blast furnace and it is generally believed that cokes vary widely in this respect. The usual operating data of the furnace afford little evidence as to the combustibility of the fuel. As a part of a general investigation of the properties of metallurgical coke, the Bureau of Mines has explored the hearth combustion zone in a number of blast furnaces by means of water-cooled gas sampling tubes driven into the hearth through the tuyeres. The attempt has been made to determine the difference in combustibility of cokes varying widely in physical properties. Data have also been obtained in an experimental combustion furnace at the Bureau laboratories in Pittsburgh. This paper gives the results of experiments, made at eleven blast furnaces, in which the composition of the gases was determined at various points in the hearth in the plane of the tuyeres. Further work is in progress in which the zone above the tuyeres will be explored. Factors Affecting Coke Combustibility Brassertl has defined combustibility as the rate of progression of combustion, or, in other words, the speed at which the carbon molecules

Jan 1, 1923

By S. P. Kinney

Sulfur has been one of the most troublesome elements encountered since the earliest days of iron smelting, and this problem will become of increasing importance as the higher sulfur coke is used, because of the rapidly diminishing supply of low-sulfur coals suitable for the manufacture of metallurgical coke. The deleterious effect of sulfur in iron and steel is well known; therefore, except in special cases, it is desirable to make the iron produced by the blast furnace as low in sulfur as possible. Sulfur enters the furnace in all of the raw materials, but principally in the coke. It comes out of the blast furnace distributed between the iron and the slag; very little passes out of the furnace with the gases. The mechanism of the reactions that cause the sulfur of the coke to pass into the slag and iron has not been studied to any great extent, although the character of the end products, and the conditions controlling the distribution of the sulfur between the iron and slag, are fairly well known. In the iron, the sulfur occurs as ferrous sulfide; or manganese sulfide in case of iron high in manganese. In the slag, the sulfur is present mostly as calcium sulfide. The presence of free sulfur1 and sulfates in blast-furnace slags is to be accounted for on the basis of oxidation of the calcium sulfide after the slag is tapped. The generally accepted reaction for the relation between the ferrous sulfide in the iron and in the coke, and the calcium sulfide in the slag, is that given by Howe? FeS + CaO + CDFe + CaS + CO

Jan 1, 1923

By Joseph F. Oesterele, Richard S. McCaffery

This investigation was undertaken to determine the quality of different iron blast-furnace slags as desulfurizing agents, and the possibility of using, in the blast furnace, materials of higher sulfur content than is now common. The solution of the problem would render possible the use of higher sulfur iron ores for pig iron and cokes containing more sulfur than now employed, and the economic manufacture of irons and steels of lower sulfur content. It is generally assumed that the sulfur that reaches the lower part of the iron blast furnace is removed from the pig iron by combining with lime to form calcium sulfide. Most of the sulfur introduced with the charge is in combination with iron or manganese or, perhaps in the coke, as a carbon compound.1 The iron and manganese sulfides are more soluble in the iron than is calcium sulfide, and as the latter is generally said to to be more soluble in the slag than the iron and manganese sulfides, this greater solubility of calcium sulfide in the slag tends to free the metal from sulfur. This greater solubility of the calcium sulfide is used not only to reduce the sulfur contents of the pig iron in the blast furnace, but by this means also low-sulfur steels are produced in the open-hearth and electric furnaces. The reaction2 FeS + CaO + CO = Fe + CaS + CO2 requires a high temperature and strongly reducing conditions in the presence of lime. The constitution of blast-furnace slags, first studied scientifically by Vogt13 indicated certain ranges of composition of the slag in which a

Jan 1, 1923

By G. P. Pilling

The use of magnetic ore in the blast furnace is a subject of increasing importance. The end of the deposits of lake ore is in sight, although not imminent, and unless some new field is discovered, the use of magnetites will be an increasing factor in the iron production of the country. Enormous deposits of magnetic ore in the country that have been practically untouched contain ore of sufficient richness and purity to prolong materially our ore supply without extensive importation of foreign ores. Magnetic ores can be divided into three general classes: Fine un-sintered, or raw ore; raw lumpy ore; fine ore that has been sintered. Fine Unsintered Ore Typical analysis and screen test of this class of ore from the Adirondack region is as follows: Per Cent. SCREEN TeST pER Cent. Fe.................... 58.00 Remaining on 4 mesh........... 7.50 SiOz.................. 7.50 Through 4 on 8 mesh........ 13.75 Al,O,................. 1.60 8 on 10 meah........ 3.75 Baseg................. 2.77 10 on 20 mesh........ 22.50 P.................... 1.00 20 on 40 mesh........ 27.50 Mn................... 0.13 40 on 60 mesh........ 2.50 S..................... Trace 60 on 80 mesh........ 10.00 80 on 100 mesh........ 2.50 100 mesh........ 10.00 100.00

Jan 1, 1923

By George S. Rice

Those who for the first time see, at a mine, a great hole caused by subsidence; or, going underground, see an extensive fall of roof or hanging wall are apt to regard such an occurrence as an accident and not a normal condition of exhaustive mining. Moreover, the public is inclined to believe that a cave or subsidence of the surface is the result of carelcssness in mining or the rapacity of the mine operators in "robbing pillars," a tern too loosely used in descriptions of coal mining. This belief is fostered by the common-law requirement that an owner of the surface or of surface improvements is entitled to full support of the surface. Court decisions have upheld this law even when that owner has sold or leased the underlying mineral, unless a clause in the sale or lease contract exempts the mining company from paying the owner of the surface for damages that may result from mining. Another reason for this belief is the earlier practice (which is still extensively followed in this country) of leaving all coal pillars unmined, except as they have been thinned by so-called robbing; by not extracting the pillars, the surface may be supported by them for years, perhaps for generations. Inasmuch as the practice of leaving permanently in the mines from one-third to one-half of the mineral is wrong, with respect to conservation of a national resource, it behooves the mining engineers to assemble data and disseminate information on the subject, pointing out that subsidence must follow complete extraction, unless expensive methods of back-filling are employed, such as are used in Germany and France. These methods inevitably increase the cost of mining and the price of the mineral produced. It is popular to speak of "waste in mining" without a realization that much so-called wasting is unavoidable unless subsidence is accepted and provision made therefor where the surface is valuable, or else the only present known alternative of hydraulically placing sand or crushed stone filling in the excavations, at an increased cost of the mineral product to the consumer.

Jan 1, 1923

By J. Parke Channing

The Miami orebody occurs in an altered Pinal schist. It is popularly known as one of the '(porphyry " deposits but, as at Inspiration and Ray, the ore is an altered mincralized Pinal schist. The orebody mined is the zone of secondary enrichment. Speaking in general terms, the area of the orebody at Miami may be considered as 1000 ft. long and 800 ft. wide. The vertical thickness varies from 200 to 400 ft., so that it is an extremely irregular mass. The study of the ground movement and resulting subsidence at Miami is complicated by the fact that the formation is not homogeneous throughout the mining area, the orebody terminating on its eastern extremity at a fault plane adjoining the Gila conglomerate. This conglomerate is a recent sedimentary deposit somewhat analogous to glacial drift and consists of boulders of granite, schist, and other material cemented with clay, and at times is quite hard. The fault dips eastward at an angle of 45". The original method of mining was top slicing, the slices being 10 ft. thick. At first, there was a good deal of experimenting with mining methods. Some undercut rooms were tried, and the stopes were filled with broken ore with the idea of removing intervening pillars by top slicing. The adoption of the top-slicing method in itself involved considerable experimenting, including some experiments with a long-wall system. The method finally adopted involved the operation of top slicing areas 250 ft. square, each with a central supply raise and ore-gathering raises, each block being worked as a unit. Mining operations in the Captain orebody, which connects with the boundary of the Inspiration property, were started by the room-and-pillar system, the rooms extending across the orebody, with widths of 10 to 15 ft., with 15- to 10-ft. pillars between. The intent was to operate the rooms as shrinkage stopes, permitting the pillars to crush when the ore was drawn from the rooms. It was found that the shrinkage stoping was unnecessary, so a system of block caving was adopted. This system was so successful in the Captain orebody that, about three years ago, the method of mining in the orebody was changed from top slicing to block caving, the method now in use. The block caving system, as practiced

Jan 1, 1923

By Howard N. Eavenson

In many of the bituminous-coal districts of this country, more than one seam of workable coal exists, and in most cases the lower seam is the more attractive, owing to either its greater thickness or its superior quality. Apprehension that the mining of a seam will destroy the availability of all overlying seams has hindered the development of many fields and has led to the unprofitable working of certain seams in order to save them from an expected total loss. The U. S. Coal & Coke Co., Gary, W. Va., was the first operator in the Pocahontas field to mine the No. 4 seam extensively, which occurs about 80 ft. above No. 3, the scam that was worked first. This was due to the fact that over large areas the upper seam was the only one of workable thickness, at that time. In two places, both seams were workable in the same area, the No. 4 being thinner and containing more impurities than No. 3 seam. In mining these areas, an attempt was made to keep the workings in the upper seam in advance of those in the lower one, and no pillar robbing was done in No. 3 seam until after pillars in that part of the upper seam directly over it had been mined. This resulted in an excessive development in the lower seam, with large areas of finished rooms and standing pillars. The top fell badly, and after a couple of years the falls became so heavy that pillar drawing was unduly expensive. To overcome this obstacle and allow No. 3 seam to be worked in some territory where No. 4 was thick, but too dirty for present use, a study was made of operating methods applied to superimposed seams in Pennsylvania and Maryland. This was started more than seven yean ago by the writer; his data, supplemented by more recent information gathered by his associates, and by two cases mentioned in recent foreign publications, form the basis of this paper. Central Pennsylvania In central Pennsylvania, the lower coal measures contain several seams of nearly the same thickness but of varying quality, and as mining

Jan 1, 1923

By J. J. Rutledge

On Sept. 4, 1914, Mine No. 1 of the Union Coal Co., Adamson, Oklahoma, suddenly caved, entombing thirteen miners whose bodies were never recovered. The seam of coal mined, the Lower Hartshorne, averaged 5 ft. in thickness and dipped at an angle varying from 22" to 30n. The strata overlying the coal seam were sandstones and shales. The mine was worked by the pillar-and-room method, the rooms being driven directly up the dip of the seam. All coal was blasted off the solid. Rooms were turned on short centers and room pillars were thin and irregular, as shown in Fig. 1. Fig. 2 is a cross-section of the form; showing the mine workings. Some cracks had been observed on the surface, it is said, at least a month before the squeeze occurred, but the collapse of the mine workings came very suddenly. As is usual when squeezes occur on such steep dips and the pillars fail, the crush progressed rapidly down the dip until it reached solid coal; there was a line of break, or draw, over in the solid coal. Several well-defined cracks appeared on the surface, after the mine had squeezed, but there was no appreciable subsidence of the surface, the weight seemed to be thrown entirely to the dip. About one year after the squeeze, and after the workings of the adjoining mine, NO. 4, had been retimbered and made safe, the writer inspected the tenth north (right) entry, or lift, off of No. 4 slope, which was below and fairly near the lowest caved portion of mine No. 1. The roof shale was composed of thin layers, which had been bent in somewhat the same manner as the leaves of a book having flexible covers are bent when the book is folded or rolled up in the hands. Though the mine workings are immediately beneath the streets and buildings of the mining town of Adamson, business was not disturbed by the squeeze, so far as any subsidence of the surface was concerned. No surface monuments were available and no elevations were taken, but the mine workings had been accurately surveyed and traversed, and the streets of the town overlying the mine workings had been carefully platted on the mine map, so that it was possible to locate accurately the cracks on the surface.

Jan 1, 1923

By Andrew B. Crichton

No more important question has come before the coal industry in the past decade than the prevention of stream pollution by mine drainage; especially in Pennsylvania, where large areas of coal land have been developed. It may be thought that the problem of labor or lack of transportation outweighs in importance that of stream pollution. We can see possible remedies for labor and transportation problems but there is no known satisfactory solution of the mine-drainage problem. The subject has been given little serious attention, for, until recently, it has been little understood; but in the past year it was brought to the attention of the coal-mining industry by the introduction, in Congress, of several bills designed to prevent the discharge of acid waters from mines or other sources into navigable streams, or their tributaries. The first legislation proposed was the Applebybill, H.R.7369, designed particularly to prevent the oil pollution of coastal waters. It contained the following provisions, which the coal men regarded as referring to the coal industry. It shall be unlawful to throw ... any refuse matter of any kind ... into any navigable waters of the United States or into any tributaries of any navigable waters from which the same shall float or be washed into such navigable waters. The chemical, steel, paper, and other manufacturing industries, as well as the mining industry, objected to this clause, the miners claiming that it would prevent the discharge of waste or mine drainage into any waters of the United States, for all streams or tributaries finally reach navigable waters. The next bill introduced was that of Congressman Briggs, H.R. 7430, an amendment to Section 13 of the Pollution Act of March 3, 1899. The original act referred chiefly to oil and oil refuse, but it provided also "that no material of any kind should be deposited on the bank of a navigable water, or tributary, which might reach the waters and interfere with or

Jan 1, 1923

By Thomas Fraser, H. F. Yancey

BefoRe a new coal-washing plant is installed, or an existing washery is remodelled and improved, considerable experimental work on the coal to be washed should be done. A thorough examination of a coal, to determine whether it can be washed successfully and the best and most economical process for securing a satisfactory grade of washed coal, calls for mine sampling, analytical work, and experimental coal-washing tests which may require several months' time and the expenditure of considerable money. Having collected the required data on the characteristics of the coal and the results secured with different types of machines under different sets of conditions, it is necessary to decide what method of treatment should be used. The interpretation of the experimental data is no small part of the problem. The first step in the investigative work is to determine from the characteristics of the coal and the manner of occurrence of the impurities whether it is possible to separate the dirt from the coal and produce a washed coal of the required quality. Then it is necessary to select the type of washer or the system of treatment that will produce the greatest amount of washed coal of this grade for the least cost. To secure this information, tests may be made at laboratories operated by consulting or contracting engineers, at the testing plants of machinery manufacturers, at commercial washeries, or in an experimental washery erected on the site of the proposed plant. Such tests will produce figures in which every factor, including analyses of raw coal and washed coal and yield of washed coal, may vary widely. To reduce these results to a common basis for comparison is very difficult. A number of plans

Jan 1, 1923

By H.E. Brauer

Among the zinc base alloys used for casting in metal moulds, pnrticularly die casting, those alloys containing aluminum usually together with copper, are probably the most widely used. The reason lies in their desirable mechanical properties and the fluidity and absence of hot shortncss which facilitate ca,sting. Objection to the use of these alloys may be raised on account of the rather frequent instances of failure of a type variously described as disintegration, exfoliation and intererystalline corrosion. In all cases which have come to our kno~vlcdge where the conditionsof service were known, failure has occurred upon cxposurc to moisture and heat varying from a hot moist atmosphere to lligh pressure steam. RIoreover, the alloys described in all such roses contain impurities or alloying metals which the present authors have found to have enormous accelerating effects on intererystalline oxid:~t'ion in zinc-aluminurn alloys. Thus Williams1 experimented with an alloy containing a large percentage of tin exposed in Cuba. Baucr2 reports failure of a boiler plug containing over 1 per cent. of impurities, doubtless lead for the must part, and Rawdon's3 examinations were madc on an alloy containing 0.1 per cent. lead also exyosctl to thc Tropics. No thorough investigation of the nature and cause of this type of failure has been made heretofore, so far as the authors are aware, although Rawdon correctly classified it as internal oxidation. We have, therefore, carried out this investigation in order to det'ermine the exact nature of this phenonienon and the effect of other metals present as impurities or intentional additions in accelerating or retarding it. In the appendix we include a considerable amount of data which may be valuable in selecting an alloy combining good physical properties with high resistance to oxidation. At the time this work was undertaken the best available equilibrium *Investigator, Metal Section, Research Division, The New Jersey Zinc Company. 'H. W. Williams—Jour. Am. Inst. of AIet,als, Vol. 11, p. 221 (1917). 2o. Bauer—ZeiL, fiir i'vletall Kunde, Vol. 12, .No. 7, pp. 129-31 (1920). 3H. S. Rawdon—Trans. Am. Elcctrochcmic.al Society (1921).

Jan 1, 1923

By John C. Branner

Five of the geologic horizons that yield oil in other parts of the world are represented in Brazil; namely, the Devonian, Carboniferous, Permian, Cretaceous, and Tertiary. Thus far, the first two have shown no evidences of being oil bearing within Brazilian territory. Not enough exploring has been done to permit trustworthy comparisons of the relative importance of the Permian, Cretaceous, and Tertiary as oil-bearing horizons in this country. The most important, indeed almost the only, information available relates to the locations of the areas and to the structural features of the several horizons. The theories regarding the physical conditions under which these rocks were laid down, however, I regard of the utmost importance. Permian Rocks of Permian age cover an enormous area in Brazil, extending from Rio Grande do Sul to Maranhao on the north, and to Matto Grosso on the west. These Permian rocks in many places are known to include oil-bearing shales and in some locations contain small veins of gilsonite. The geologic map of Brazil shows that the Permian area is widely distributed, but there is considerable doubt about the origin of some of the rocks. Some of the lower Permian beds in southern Brazil contain marine fossils, but in Minas no fossils have as yet been found in them, and in Bahia, at only one locality have a few Permian plants been found. Indications of oil have been found in the states of Sa0 Paulo, Parana, and elsewhere farther south, but wells drilled in the Permian of SaO Paulo near the Morro do Bofete did not find oil. One well has been started, by the Brazilian Government, in the Permian of Parana near Marechal Mallet, close to latitude 26" south, but thus far oil has not been found.

Jan 1, 1923

By Frank Feuille, Edward Schuster

As the time allotted is short, we can present only a general idea of the oil laws in the Latin-American republics, as a supplement to Bulletin 206 of the Department of the Interior compiled under the direction of J. W. Thompson of the Bureau of Mines and entitled "Petroleum Laws of All America." We shall not discuss the European colonies in Latin-America nor the island republics. As to the countries discussed, we shall attempt to give the main features of such special petroleum legislation as has been adopted prior to the early part of this year; where no special petroleum laws exist, we must look to the mining codes for light on the petroleum policy. As the laws and regulations for the extraction of the metals are often difficult of application to, and are lacking in many essentials for, the petroleum industry, it is best for persons or companies desiring to enter, on a large scale, into the petroleum exploration and development of countries not having special petroleum legislation, to obtain a concession contract from the executive of the country under consideration, and to have the concession approved by the congress. If this concession, which would then be a special law, contains nothing contrary to the constitution of that country and does not infringe on vested rights of third parties, it should be reasonably safe. If in such country there is some doubt as to whether the petroleum subsoil is owned by the nation or the private surface owner, only public lands should be covered with the concession. Guatemala is the only republic in the group that discriminates directly against foreigners. Bolivia, Ecuador, Mexico and Venezuela require waivers of diplomatic protection.' Colombia requires foreigners to agree to be bound by its alien law. In addition,Mexico makes it unlawful for foreigners to acquire direct ownership of real estate, including mines, within a zone of 50 km. along the coasts and one of 100 km. alongitsland

Jan 1, 1923