Search Documents

[PRESIDENT GEORGE OTIS SMITH, District 4 WASHINGTON, D. C. PAST PRESIDENTS SAMUEL A. TAYLOR, District 3 PITTSBURGH, PA. E. DEGOLYER, District 0 NEW YORK, N. Y. FIRST VICE-PRESIDENT W. H. BASSETT, District 1 WATERBURY, CONN.]

Jan 1, 1928

By Carl Swartz

ALTHOUGH a number of articles appeared during the war advocating the use of cadmium in lead-tin solders, very little information of value can be found in the literature regarding the properties of solders containing cadmium. In most of the published articles the cadmium seems to have been considered merely as a partial substitute for tin in a tin-lead alloy rather than as an essential constituent of a ternary alloy. The primary object of the substitution of cadmium for tin was to lessen the amount of tin required, at a time when the latter was scarce and high-priced, and thus to produce a cheaper solder. While this object was accomplished, the new properties resulting from a change from a binary lead-tin alloy to a ternary lead-tin-cadmium alloy were not given proper consideration in many cases. For the past few years, the American Smelting & Refining Co. has been marketing a very considerable amount of cadmium in the form of lead-tin-cadmium alloys for use as solders for certain special purposes, and the successful use of these solders suggested that if more extensive knowledge were available concerning the properties of lead-tin-cadmium alloys of various compositions their field of usefulness might be materially extended. The investigation described in the present paper was undertaken to obtain this information and, by means of tests under conditions approaching those of practical use, to determine the suitability of cadmium solders for various purposes.

Jan 1, 1928

Jan 1, 1928

By E. F. Kern, W. W. Loo

A review of the literature on the reduction of cassiterite showed that scarcely any progressive changes were made in the methods of reducing cassiterite until within the last two decades, and that during that period many improvements in the metallurgy of tin have taken place. Since 1914 the world's consumption of tin has increased considerably, resulting in the exploitation of primary tin deposits such as the Bolivian lode, which has become an important source of tin. On account of the low tin content of Bolivian ore, and the presence of objectionable impurities of the reduced tin, the smelting of this ore and the refining of the tin has changed considerably from the methods formerly used. A comparative study of the methods of smelting cassiterite concentrates suggested that an investigation be planned so as to determine what factors effect the extraction of tin from its ores by reduction with carbon. The first part of the experimental work was the determination of whether roasted cassiterite concentrates can be reduced by carbon without the use of flux, and the reduced pellets of tin be collected into a single mass separate from the dry gangue residue. The second part of the experimental work was a comparison of the effect of variations of the different factors on the smelting of roasted cassiterite concentrates: first, the effect of varying the composition of the slag; second, the effect of varying the amount of reducing agent; third, the effect of varying the relative amount of the resulting slag; and fourth, the effect of different kinds of reducing agents. Review of Literature Experiments on the smelting of Bolivian tin concentrates were made by James P. Gill in 1920 in the metallurgical laboratory of the School of Mines, and submitted as a graduate thesis. The results of these tests are fully reported as they are preliminary to the experimental part of this paper, and also because they have not been published. The variables investigated by Mr. Gill were: (a) the effect of temperature on the rate of reduction of cassiterite concentrates; (b) the time required for

Jan 1, 1928

By J. Gross

G. H. Clevenger, Chairman of the Milling Methods Committee of the Institute, made the following introductory remarks: "Several years ago, a number of us felt that the time was ripe for a fundamental investigation of crushing and grinding. At the outset, it appeared that the first thing we needed was a yardstick whereby grinding efficiency could be measured. "The U. S. Bureau of Mines has been most generous in cooperating with the Milling Methods Committee in getting this work well under way. John Gross, who served the committee for a year as secretary, was placed in charge of the investigation and has been ably assisted by S. R. Zimmerley. "Messrs. Gross and Zimmerley will now present the Progress Report covering their work to date." PROGRESS REPORT J. Gross, Salt Lake City, Utah. -This has not been a simple problem, and when I tell you that we can give you a verbal report of what we have done during three years in five or ten minutes you will realize that we have necessarily done a great deal of work that does not appear in the final results. We have been in a virtually new field. Therefore, we have had to feel our way at each step so as to be fairly sure we were correct. The first thing that was realized in this problem was that unless we had some method of measuring what happened when we crushed an ore, we might as well quit and not go further. We realized that if we tried to measure the results of crushing or grinding by the ordinary sizing test we would not get anywhere. We could sieve down to say 200 mesh fairly accurately; we could even go one sieve size further with a little less accuracy, and then we were absolutely lost, unless we went into microscopic measurement. Even this latter method would not have been satisfactory. The question was: what were we going to measure? If we were going to measure size, we might measure one particular dimension of a particle and be off 200 per cent. or more. If we tried to measure surface, we would have something tangible; the surface of a particle, no matter how irregular, is something definite, far more definite than any linear dimension would be. Moreover, if we could measure surface, we would immediately have a method of checking the Rittinger law as to whether it was or was not correct. So the first thing that we sought was a method whereby we could measure surface on crushed particles or, we will say, on particles; it would not make any difference whether crushed or not. It then became a question of what kind of particles we were going to use in obtaining a method for surface measurement. We realized that it would be rather a com-

Jan 1, 1928

By William H. Emmons

The problem of the metalliferous veins has always been an outstanding one in the science of ore deposits. In recent years interest has been stimulated by Spurr, who maintains that veins have consolidated from magmas that have densities as great as the densities of ordinary rocks. Lindgren published a noteworthy paper1 in 1926, in which he supports the theory that veins are deposited chiefly by hot waters. Lindgren's paper was discussed by Singewald, Spurr, Kemp, Anderson, Colony, Bateman, Porter and others. The discussion, in the main, was centered on the interpretation of fragments that are included in veins. This paper also treats the problems of fragments in veins and includes a reply to a review by Spurr2 of a bulletin by Larsen and myself3 published by the United States Geological Survey on the geology and ore deposits of Creede, Colorado. Mineral veins containing fragments of the wall rock are common. At many places the fragments are completely isolated, one from the other, and are entirely surrounded by vein matter. It has been stated that the vein matter around the fragments was heavier than the fragments and that the latter were floated in a magma. J. E. Spurr, who is the leading advocate of this hypothesis, 4 urges that normal mineral veins were deposited by solutions heavy enough to float fragments of the country rock, and it is mainly on this relation that he bases his theory that veins are deposited by solidification of magmas. If it can be shown that vein-forming solutions have a specific gravity greater than rock (2.77), one is justified in regarding them as true mag-matic solutions. It is shown later in this paper, however, that at Lead, S. D., water not more highly concentrated than ordinary drinking water is depositing vein matter around fragments of schist and of steel in such a manner that the fragments are completely isolated and completely surrounded by the mineral cement.

Jan 1, 1928

By S. A., Taylor

IT is very difficult to arrive at exact figures for the cost of maintaining excess capacity of coal mines, but we can approximate the various items. To do this, I will take the Pittsburgh district of Pennsylvania and the other districts can be compared to this one. I believe we can take the depreciation item of plant ac- count as a whole and discount it over a period of 20 years; while this is high for some items it is low for others and I believe it is not far from a safe basis. This equals 5 per cent per year, and this depreciation will take place about as rapidly when not in use as when in operation. A fair value in the Pittsburgh district to- day for plant and houses is close to $4 per ton per annum. At 5 per cent this will equal 20 cents per ton per year. The item of keeping the mine in condition, free from water, etc., will be close to an average of 2y2 cents per ton per annum.

Jan 1, 1928

By G. L. Oldright

THE development of the reverberatory furnace for smelting copper ores up to 1912 was described by E. P. Mathewson1 with details concerning the great changes in dimensions of the furnace. Hayward2 tabulated similar data, giving developments up to about 1924, in his revision of Hofman's Metallurgy of Copper. DEVELOPMENT OF PRESENT SMELTING PRACTICE Dimensions of Furnace Very great changes were made in the dimensions of the smelting hearths of the furnaces in the period from about 1800 to 1906, the length increasing from about 11 to 116 ft., and the width from 8 to 19 ft. During this time the tonnage smelted increased from about 9 to 250 tons per 24 hr., and the tons of charge smelted per ton of coal increased from 0.77 to 4.3. Dr. Mathewson3 noted no great difference in the "fuel ratio" (i. e., the amount of charge smelted per ton of coal) as the furnace at Anaconda was increased in length by stages from 85 to 116 ft. (The percentage of copper in the slag, however, was lowered from 0.42 to 0.36 per cent. The other components of the slag were not given.) Lump coal fired on grates was the fuel used during this period. The practice in operating the furnaces over such a length of time naturally varied considerably, and there were differences in composition and nature of the charge, yet it may be considered that the improvements made were due largely to increases in the size of the furnace used. Doubt-less some credit should be given to improvements in operating technique, like changes in the methods of firing the lump coal. However, the greater part of the advance was probably due to factors influencing the

Jan 1, 1928

By L. O. Howard

R. HATCH, Garfield, Utah.-The object of the meeting, I believe, is to determine the proper chemical composition to insure long wear of a ball in a mill, This might also apply to rods. I feel that there is only one way of determining accurately the wearing qualities of balls in mills, and that is by actually wearing out 400 or 500 tons of different kinds of balls. Two things add to the wearing qualities of a ball: (1) the tenacity, with which the particular particles of iron or steel are cemented together; (2) the individual hardness of each particle. My experience is that a ball that has a Brinell of 550 to 650 will give comparatively long life. There is considerable difference of opinion as to the best steel and iron alloys necessary to produce a satisfactory grinding ball. Some favor chrome, some manganese and some nickel. Personally, I believe cast iron alloyed with chrome makes the best ball for small sizes; for large sizes (3 1/2 in. and up) steel alloyed with manganese is best. L. 0. HOWARD, Pullman, Wash.-How would this method apply to lining? A. KissocK, New York, N. Y.-I do not subscribe to that exactly. As I am connected with the Climax Molybdenum Co. you would hardly expect me to. We have been much interested in trying to work out this grinding-ball problem and have spent a great deal of thought and effort on it. As we are associated with the American Metal Co. and have a number of properties of our own, we are in position to try our ideas on ourselves first. We have tried different compositions, but have not done anything very remarkable with them yet, except that we have been able to say that the combination of chrome and molybdenum has given the best wearing ball. Mr. Hatch feels that iron is the best medium for grinding, but since toughness as well as hardness is a factor in wearability we feel that a well made steel is better for this purpose. Another difficulty with cast, or chilled, iron is lack of uniformity from day to day or from heat to heat and the impossibility of producing balls free from blow or shrinkage holes which materially affect their life. If cast iron is made hard it becomes brittle and lacks stretch or toughness. This prevents its use in the larger sizes, as breakage is a serious handicap to efficiency. We have tried hard and brittle balls and softer but very tough balls and have proved that maximum hardness, with sufficient toughness to prevent breakage, is the most important factor in resistance of a steel to abrasion. It is well known that chromium is one of the best hardening agencies for either iron or steel, and molybdenum is recognized as an element capable of introducing toughness. In other words, the proper combination of chromium and molybdenum permits unusual hardness with still sufficient toughness to stand up under severest impact. It is yet too early to give any actual mill results of this new combination and though we are proving our ideas at our own properties we have to depend on others to help us make the data more general and more worth while and would like to get some tests

Jan 1, 1928

By Joseph E. Pogue

The past year in the petroleum industry was one of overproduction, rising inventories, low prices, and meagre to vanishing profits. This outcome was the result of a long period of intensive and uncompensated effort on the part of both financial and industrial interests, to stimulate supply on the theory that the primary problem facing the petroleum industry was the development of an adequate reserve of raw material to protect a large and ever-growing investment. The stimulus was applied in various forms and through diverse channels: capital had long flowed into the industry in excessive amounts under the attraction of large expected profits; the price level for crude petroleum had persistently been influenced by speculative considerations, with the result that prices declined slowly in periods of flush production and were quick to advance in anticipation of statistical improvement, thus maintaining a superfluous degree of stimulus on wildcatting and on drilling; speculation in inventories had led to the unsound, or at least unusual, business practice of accumulating huge stocks of oil; and, above all, the industry had directed the potent force of technology to the expansion of supply and achieved radical results in accelerating oil discovery, speeding up the rate of oil extraction, and enlarging the recovery of gasoline and lubricating oils from the raw material. In short, the economic conditions of 1927 were exactly those to which the objectively driven enterprise of the petroleum industry had long been directed; and the undesirable financial consequences arising therefrom reflected no lack of success in what had been set out to be achieved, but rather the failure to have established concurrently the necessary means of economic control to prevent the immediate conversion of reserves into current supply, and likewise the oversight in neglecting to apply the technological force to the enlargement and diversification of the market for petroleum products. Perhaps, when viewed in its longer perspective, 1927 will stand out as the turning point in the economic policy of the petroleum industry, when the technique of rationalizing production made its initial claim for recognition.

Jan 1, 1928

By D. L. Johnson

Only general treatment of a subject of such scope can be given in a short paper, therefore, except in a few instances, statistics and descriptions of specific installations are omitted. The earlier applications of electricity to the production of petroleum in the Mid-Continent field were widely separated chonologically, each holding a special interest, and each contributing greatly to the present development. Electric Pumping One of the first installations of electric pumping was on a lease near Jenks, Okla., in the Arkansas River bed, where a difficult problem was solved by the use of motors. The Arkansas River had frequent flood periods which interfered seriously with the use of jacks and pull rods. Small piers were built with old casing used as piling, and upon these were set small jacks driven by 3-hp. squirrel-cage motors. The starting switches were located on a bank and the power was furnished by a small generator, which was driven by an oil country gas engine. This installation was made in 1913 and is, I believe, still in satisfactory operation. In 1914, the Cushing field came in and the Hill Oil & Gas Co. electrified its Shamrock property, using eight-pole Star Delta motors, rated at 10 to 30 hp. and belted through countershafts to the band wheel. Power was furnished by a small generating plant consisting of two 135-kw. machines, gas-engine driven. Considerable difficulty was experienced in the early operation of this station because of low voltage. It is characteristic of small alternating-current generators that voltage regulation will be poor with widely fluctuating loads. This field had three producing sands, and a number of wells were redrilled with the motors, and this, together with a great deal of swabbing, was responsible for the bad load conditions. However, when the wells had settled down to steady operation, the electric equipment functioned satisfactorily, and continued in use as installed until a few years ago when the present owners contracted for service from a central-station company and shut

Jan 1, 1928

By V 9. 0 / 300 dpi

ATHOUGH turquoise mining was, so far as we know, the first large, well-organized mining operation,' gem mining, from the Roman con-quest of Egypt until the opening of the South African pipe diamond mines some 50 years ago, was largely carried on' by individuals 01' small companies in a relatively primitive way. Now" however" gem mining does not yield in efficiency or in scale of operations to the mining of other mineral products. In 1926 the diamond mines of the world milled some 9,000,000 cu. yd. and produced 0,43 cu. yd. diamonds, a remarkable example of concentration. The Premier Diamond Mining Co. up to Oct. 31, 1927, had milled 116,455,550 loads (each of 16 cu. ft.) from which 26,-217,144 carats of diamonds" worth £29,897,971 2s, 9d., were recovered. The Burma Ruby Mines, Ltd., operating sever-al alluvial mines in Burma in 1911-12, mined and milled 1,479,845 truckloads of gemmiferous earth for 15c. per load. We of the industry can there-fore, with good grace, disclose some of the myths and also describe some of the primitive mining methods of the, dark ages of our industry. The methods, so far as I know, were not patented, and if they were, the patents have expired, so that engineers in other branches of the art are free to use them if they see fit.

Jan 1, 1928

By Irving Crosby

ELECTRICAL prospecting by potential methods has been applied to mining problems for some years and determinations of the depth to bed rock have been made, but so far as is known it has not been used previously in the solution of civil engineering problems, such as investigating the foundations of dams. During the past winter and spring the senior author has been engaged as consulting geologist in studying the site of a large darn on the upper Connecticut River and has had the satisfaction of introducing electrical prospecting to foundation problems. The valley across which the dam is to be built is underlaid by a deeply buried preglacial gorge which is filled with glacial deposits. An extensive drilling campaign was in progress, but the work was unusually slow and expensive on account of the number of boulders in the overburden. The necessity of speeding up the work was pressing and it was decided that much of the needed information could be obtained by geophysical methods. After investigating the various methods and conferring with the company engineers and with the consulting engineer, Albert Crane, a contract was made with the Schlumberger Electrical Prospecting Methods, and an observer with apparatus was sent to the dam site the first of April, 1928. The problem was to determine the depth to rock at various points in order to prepare a contour map of the bed-rock surface and outline the buried gorge in the vicinity of the dam site. Over one hundred determinations of depth have been made and the bed-rock topography, is now known in considerable detail. In addition, some information has been obtained about the nature of the overburden. The drilling has been continued; in fact, two additional drills have been put to work, and the electrical determinations have been checked at several points. At one of these the depth to rock given by the electrical work was 142 ft. and the drill found rock at 147 ft., an error of less than 4 per cent. The electrical work has also been checked by the geological study, and it has been found that when the electrical determinations are in agreement with the geological expectations they are probably reasonably accurate. When the electrical interpretation of the sub-surface topography is incon-

Jan 1, 1928

By C. E. Reistle

All crude oils become more viscous when chilled, but the only oils that congeal and precipitate paraffin to such an extent as actually to cause production troubles are those that contain an appreciable amount of wax. In handling these oils of high wax content, three distinct problems may be encountered before the oil reaches the refinery. The first problem is the precipitation and accumulation of paraffin in the well, either in the oil string or on the face and in the pores of the sand. The second problem is the accumulation of paraffin and the congealing of oil in the transportation lines. The third problem is the precipitation of paraffin and the formation of tank bottoms. Factors That Control the Solubility of Paraffin in Crude Oil Two main factors, possibly three, govern the solubility of wax in crude oil. The first of these is temperature. The solubility of wax in crude oil increases with an increase in temperature, and as the temperature approaches the melting point, the wax becomes soluble in all proportions in the crude oil. The higher the melting point of a wax, the less soluble it is in crude oil below its melting point. All crude oils containing wax can be chilled to a point where the oil is saturated with wax. If the temperature is decreased below this point, some of the wax will crystallize from solution. Fig. 1 shows the effect of temperature on the solubility of crude paraffin in oil. The second factor is the amount of volatile constituents and gas removed from the crude oil. Evaporation of the volatile constituents and gas lessens the volume of the oil and concentrates the solution of wax in the oil; therefore less wax can be held in solution at a definite temperature. As the natural amount of wax present in the oil is constant, this results in the oil becoming saturated with wax at a higher temperature than if the volatile constituents and gas were still in the oil. As an example of this, a fresh sample of crude oil having a gravity of 39.8

Jan 1, 1928

[ ]

Jan 1, 1928

By E. G. Leonardon

THE first to appreciate and foresee the value of applying electrical measurements to structural studies was Prof. Conrad Schlumberger, Professor of Physics at the School of Mines in Paris. One of his earliest practical undertakings in this line was carried out, in the field, at Fierville-la-Campagne, Normandy, in 1912. His book, published in 1920,1 still stands as an authoritative, fundamental treatise on the use of the electric current in geological studies, in spite of the rapid evolution of geophysics during the last seven years. A remarkable feature of this book is that, even then, it stressed the role of electricity in structural investigations and made public the first successful results obtained therewith. Stratigraphic studies have been pursued continuously by Conrad Schlumberger and his associates since 1912, the only interruption being the World War. The results attained demonstrate the wide possibilities of electrical exploration in structural work. This field of activity is, at the least, as varied and valuable as the search for ore. It is curious that until very recently it has so slightly attracted the attention of geophysicists and geologists on this continent. The purpose of this paper is to present briefly some examples of the practical application of the potential methods to geological studies. These examples are chosen from a number of problems solved in the field by our firm, in the course of its consulting practice. Certain fundamental points are briefly stated before the field operations and interpretations are described.

Jan 1, 1928

By T. A. Wright

The sampling of waste materials containing copper, lead and tin has taken on a new significance within recent years, and is of increasing importance, on account of the entry of some of the copper refineries into this field and the tendency towards consolidations among the smelters. In the past, such material was sold on the basis either of a rough or grab sample or of casual inspection of the lot. The two principal sources of this waste are the processes of fabrication and the scrapping of automobile, electrical, plumbing, railroad and other equipment. In both cases much material can be sorted, salvaged and sold by classification and grade to be melted "as is" or with the addition of new or virgin metal. The increasing care in classifying exercised in the large manufacturing plants tends to increase the proportion of this usable scrap; on the contrary, the increasing use of more complex and special non-ferrous alloys tends to make sorting and grading more difficult in turnings, borings, clippings, etc., and consequently is making sampling of more moment. In tin, lead, aluminum, and zinc furnace by-products such as ashes, drosses, skimmings, etc., the trade practice of evaluation has not varied much. For instance, tin drosses, battery lead, and aluminum skimmings are ordinarily sold on what is called "metallic button" or "metallic recovery" or ('metallic yield." Copper and lead waste, however, is being sold more and more on actual copper and lead contents based on sample and chemical analyses. This paper will be devoted chiefly to the sampling of materials suitable only for refining and recovery of one or more of the metals present. The methods described are often based on the fact that but one metal, such as copper, is to be paid for. The loss of volatile constituents in melting does not appreciably affect the final copper result, as the "after-melting" assay can be readily calculated to the "before-melting" basis, but if smelter efficiency continues to increase, so that in time zinc, for instance, may be recovered on a paying basis, the method of sampling dirty brass, for example, will have to be changed also. As a matter of fact, we may expect that improved refining processes will make possible the partial recovery of lead and tin which are now lost.

Jan 1, 1928

THE man who forgot to mail the letters his wife gave him was for once justified at Tulsa, for envelopes, scratch paper and tablecloths were all in demand and through the two days of the meeting of the Petroleum Division, pencils were busy everywhere sketching out diagrams, drawing curves, figuring, or just taking notes. Those attending took the serious papers seriously, and discussion was wide-ranging but pointed. Despite the highly technical character of the papers presented, the chairmen had never to call for discussion; it was only necessary to say the paper was open for it. Both days the meetings lasted until after five in the afternoon, and it was enthusiastically voted to advance the meeting hour on Friday, in order to give more time. In all, ten papers, abstracts of which appeared in MINING AND METALLURGY for October, and copies of all but two of which were available in print, were presented in the two days, and no more could have been handled to advantage in that time. All but one of these dealt with problems of production engineering. That, the opening paper, was a general review of demand, supply and price in 1928, by Campbell Osborn, in which he argued for the price control of production and showed how the economic conditions determined development. J. Elmer Thomas presented a carefully prepared review of the same data, but came to somewhat different conclusions as to trend, and J. E. Pogue pointed out that in recent years it has been the manufacturing rather than the producing industries that have been notably profitable. These and other discussions were too long to be reported here, but will be printed in full later.

Jan 1, 1928

Jan 1, 1928

By H. W. Camp

Research is defined, scientifically, as a "systematic investigation of some phenomenon, and also a search for hidden treasures." Chemists tell us that the hidden treasures of petroleum are far richer than the products which have been best known to us. However, these secrets will be discovered only through intensive and systematic, as well as scientific, industrial research. Indeed, the scope of the subject is so great that such an intensive research program should be assumed by a centralized organization supported by the petroleum industry as a whole. Such organization should assume the responsibilities for investigation of new products and development of markets for such products. Gasoline, the chief product of the petroleum industry has become a cheap commodity. The continual uncontrolled overproduction of crude petroleum, the intensive competitive condition in the marketing of petroleum products and the increase of refining efficiency and installing of cracking facilities, have all combined to lower the market value of gasoline. The purchaser has profited from the lower cost of gasoline by way of lower prices so that today the most important product can scarcely be manufactured at a profit. In other fields, manufacturing industries have diversified their products when faced by a similar situation. Thus, they have been able to widen their marketing outlook. Why cannot the petroleum industry employ the same tactics? Right now we are hearing much discussion concerning the development of a wider market for existing petroleum products and new products for existing or prospective markets. For instance, we can cite recent developments for use of propane, butane and ethylene. Butane has been found to be an efficient and inexpensive refrigerant, especially adapted to home refrigerating systems. Propane and butane fractions of natural gasoline may be shipped under pressure and may be used as a substitute for, acetylene in cutting torches in connection with oxygen. There is a possibility of substituting butane for gas oil in the carburation of coal gas, as we know that butane contains practically the gas enrichment as the same volume of gas oil and should prove to be a superior product for

Jan 1, 1928