Search Documents

Increased world consumption of crude and products coupled with the trend toward supplying this demand from the nearest and most economical source of supply had the economic effect of broadening the demand for Venezuelan crude. As a result of this, Venezucla produced more in 1934 than in 1929, the previous peak year. During 1934 Venezuelan output is estimated at a total of 139,382,000 bbl., a daily average of 381,868 bbl., against 120,442,000 bbl. in 1933, a daily average of 329,978 bbl. This is an increase of 51,890 bbl. per day. It is interesting to note from the comparison of production for the past 10 years (Table 1) that in spite of the fact that Venezuela produced more in 1934 than in 1929 its share of world production is slightly less than in 1929 and 1930. During the latter part of 1934 Vcnezuela produced its first billionth barrel of crude. Only three other crude-producing countries of the world have attained this distinction; namely, United States, Russia and Mexico. Venezuela still ranks third in the producing countries of the world, being surpassed by the United States and Russia. Exports of crude and products from Venezuela for 1934 are estimated at 133,400,000 bbl. This is an increase of 16,107,000 bbl., or 13.73 per cent as compared with 1933.

Jan 1, 1935

By Howard A. Smith

OF late considerable experimental and theoretical interest has been shown in the rates of transformation from a single phase, usually a supercooled solid solution, into one or more phases. Such reactions may involve both diffusion and transformation of the major constituent, as in iron alloys, or it may simply involve diffusion, as in superstructure formation and in age-hardening systems. Most of the work has been confined to ferrous alloys1-9† although two investigations have been made on copper alloys 10-11. That such work may be of considerable practical importance has been demonstrated by Bain12, by the workers at the Kaiser Wilhelm Institut für Eisenforschung13, 14, and by the everyday use of precipitation and age-hardening principles15. Experiments in this country have generally followed Davenport and Bain's technique of rapid supercooling followed by isothermal treatment. In Germany16, 17 the work has been extended to the study of the influence of accurately controlled and measured rates of cooling. The work on steel indicates that there are two subcritical temperature ranges where reaction starts sooner after quenching and proceeds at a more rapid rate than at other temperatures. At subcritical temperatures above Ar" where reaction is dependent upon atomic migration there is a period of time of which the length depends upon the alloy content and the temperature, before which no reaction has been detected. Davenport and Bain1 find that different sorts of atoms in solid solution in gamma iron affect the length of this "prereaction" period differently, manganese

Jan 1, 1935

By Cyril Smith

A STUDY of the precipitation-hardening of copper steels1 led the authors to investigate malleable iron containing copper, for the low-carbon ferritic matrix in malleable iron should lend itself admirably to precipitation-hardening. It was soon found that in addition to rendering malleable iron susceptible to improvement by precipitation-hardening treatments, copper has another potentially useful effect as an accelerator of graphitization. Brief mention of these effects was given in a general paper by Lorig and one of the present authors2; the present paper gives further details on the graphitization and precipitation-hardening effects only. After the completion of this work a paper by L. Lykkin3 appeared, confirming the authors' conclusions regarding graphitization.

Jan 1, 1935

By L. P. Durham

DuRing the early mine development period, 1929 and the first part of 1930, a 300-ton pilot-plant concentrator was built at Nkana mine of the Rhokana Corporation, Northern Rhodesia. This plant operated from May 26, 1930 until Oct. 26, 1931, treating 101,080 tons of Nkana ores and producing 4372 tons of concentrate. The plant was built, primarily, as a test unit to determine the grinding characteristics, floatability, etc. of the Nkana ores and other ores of the Rhodesian copper belt and to supply sufficient data on which to base the design of a 5000-ton concentrating plant at Nkana mine. The test unit operated wholly on development ores and no attempt was made to grade or select the ores from any section of the mine. The average assays for the 17 months of operation are given in Table 1. The first ground was broken for the 5000-ton concentrator during June, 1930, and the construction of the plant was completed in November, 1931. The plant started on Dec. 10 and has operated continuously since that date: The whole of the concentrating plant is compact and closely connected, yet with sufficient space for expansion of all sections up to 20,000 to 25,000 tons per day capacity. Mining operations are carried on along a length of about four miles on the easterly limb of the Nkana syncline. This length includes the North orebody, from which all production has thus far originated, and the Mindola orebody, now being developed for production. The ore-bearing measures in the North orebody are leached for some 75 ft. below the surface; the oxidized zone varies in vertical extent from 100 to 150 ft. Practically all the ore below the 200-ft. level is sufficiently

Jan 1, 1935

By Thomas A. Wright

No symposium on die-casting could be complete without consideration of the methods of formula and impurity control. No corisideration of control would be complete without discussion of that new tool of the analytical chemist and inspector, the quartz spectrograph. Just as there is an increased appreciation of the possible applications of the die-casting process and of die castings, so too is there, slowly but surely, of the spectrograph. At present the role of the instrument might well be compared with that of brass or magnesium die castings. Neither is as widely understood or known as they will be. Product specifications are increasing and are getting more explicit and often more rigid. The designer, metallurgist and production engineer or superintendent will be forced to depend more and more on the chemical laboratory. Sampling, as well as analyses, testing and inspection problems will grow. The chemical laboratory must meet its increased responsibility and use of the spectrograph will become more common. Advantages of increased precision, greater speed, lessened labor and often lower costs cannot be ignored. It will be the purpose of this paper in part to outline the respective fields of chemical and spectrographic analyses and to indicate where one may overlap the other and in part to indicate certain possible sources of contamination of zinc-base die-cast alloys in particular. Composition Aluminum.-Aluminum die die castings are expected to conform to the specifications of the Amcrican Society for Testing Materialslt and the Society of Automotive Engineers2. The A.S.T.M. has recognized seven aluminum alloys in Tentative Specification B85-33-T. TWO are straight silicon and the remainder are of the copper-silicon type of which alloys VIII and IX have in addition respectively 2 and 4 per cent of nickel, but unlike the others are not covered by S.A.E. as well. All seven call for rigid control of certain impurities. With the exception of alloy XII,

Jan 1, 1935

By Wolfram Ruff, H. A. Schwartz

THE spheroidal form of the temper carbon nodules in malleable cast iron and of the graphite mottles of "mottled" cast iron suggests that in both all the graphite in a given mottle or nodule grew from a single center of crystallization or nucleus. ‡ There is, however, a distinct metallographic difference between the mottle and the nodule; the area of mother metal impoverished in combined carbon by the crystallization of graphite in a mottle is practically coextensive with the ramifications of the graphite, while the impoverished zone of metal corresponding to a given nodule is always larger, and usually much larger, than the approximately spherical mass of graphite crystals forming the nodules. Furthermore, the mottle probably is formed during freezing and the nodule almost always at a considerably lower temperature. Assuming that the nodules or mottles can be used as a measure of the existing nuclei (capable of germination) we propose to record certain observations as to the graphitizing reaction in the light of the number and habits of growth of these nuclei. The present authors, in cooperation with others 1-7, have reported upon various cognate aspects of the problem. The fact that temper carbon is a mass of flakes and not a solid granule has become well recognized since the introduction of an improved polishing technique8,9,10 for cast iron. The problem of deriving from the circular planar intercepts

Jan 1, 1935

By K. Heindlhofer

Estimates of the "plasticity" of a metal are commonly deduced from three types of test—tensile, torsion and impact. The several results have been more or less at variance, though this disparity has attracted little notice, largely perhaps because they have been expressed in different terms. The discrepancy between the results of the three tests becomes obvious when each is made at a series of low temperatures, for the temperature range within which the "plasticity" of iron largely disappears proves to be very different in the three types of test. The rather abrupt disappearance of "plasticity" of iron within a narrow temperature range cannot be due to any physicochemical change (such as a precipitation) taking place in the material at that time, because the original plasticity is immediately regained when the temperature of the material is brought above the sensitive range. Accordingly this difference in behavior shows that the "plasticity" of a metal depends upon the mode of action of the stresses which produce the deformation, and therefore upon the method of test. Analysis of the stresses leads to the conclusion that the observed plasticity of a metal is determined by the relation between its resistance to rupture by separation and its resistance to shear (slip), on the one hand, and between the effective normal and shearing stresses on the other; and that the relation between the two resistances does not in general remain constant with change of temperature, and may somehow be altered to some extent by the previous treatment of the specimen. This suggests the view that the results of none of the usual mechanical tests are directly comparable even for a single metal tested at a series of temperatures, or for a series of metals at one temperature, because the proportion of the total resistance of the metal to the test contributed by the

Jan 1, 1935

By T. F. Petty

Oil and gas production in North Central Texas has been found in sands and limestones in the Cisco, Canyon, Strawn and Bend series of Pennsylvanian age and in lime of pre-Pennsylvanian age. Production ranges in depth below the surface from 150 to 4500 ft.; a few wells have been drilled to depths in excess of 5500 ft. and penetrated rocks of pre-Cambrian age. In Table 1, the average depth of the pools is shown. No mention, however, is made in this table of approximately 30,000 bbl. of oil produced in Callahan County from a pre-Pennsylvanian pay, presumably the Ellenberger, and an excess of 1,000,000 bbl. of oil produced from limestone, which has been identified as Silurian in the south part of Young County. This well is being produced at the present time. In Table 1 a great many pools of minor importance are listed, which are merely productive spots, and throughout the various producing counties there are numerous similar spots, which might be listed as pools. Their production, however, is listed in the county totals. In Table 2, the totals of the oil wells, gas wells, and dry holes drilled before Jan. 1,1935, include only wells on which records are available to the writer. In Brown, Callahan and Shackelford counties 2924 very shallow wells (150 to 600 ft. deep) have been drilled, on which the record is not available. Possibly there are other wells that were drilled before the district was adequately scouted. No classification as to the depths of this total of 30,644 wells is available at present. Initially, nearly all the oil wells of North Central Texas produced gas, and several areas producing dry gas have been partly developed. A number of casinghead gasoline plants strip the gasoline from the gas produced with the oil, and the manufacture of carbon black is an important industry in Stephens County. Dry and residue gas are marketed through systems serving the various towns of the district, San Angelo to the southwest and the cities of Forth Worth and Dallas to the east. Considerable gas is used in repressuring several pools, the most important of which are the Stover of Brown County and the Cook of Shackelford County. During the past year, 32 gas wells were completed, adding a

Jan 1, 1935

By Alden B. Greninger

THE study of mosaic structure of crystals1 has been confined until recently to the field of theoretical physics Crystallographers, in general, have neglected the subject, although X-ray crystallographers constantly make use of formulas for intensities of X-ray reflection as modified by mosaic structure Work on mosaic structure has centered chiefly on the task of proving or disproving the secondary-structure theory of Zwicky,2 and very little attention has been paid to the visible imperfections of crystals A Goetz has been responsible for most of the supposed experimental confirmations of Zwicky's theory 3 On the other hand, Smekal,4 and Orowan,5 among others, maintain that these is neither theoretical nor experimental evidence to substantiate Zwicky's secondary structure

Jan 1, 1935

Jan 1, 1935

By E. W. Davis

Iron-ORE beneficiation methods are determined largely by blastfurnace requirements. There are still many millions of tons of direct furnace ore in the Lake Superior district and blast furnaces are designed and operated for the most efficient use of this material. Beneficiated ore must be so prepared that existing furnaces may use it without alteration in design or radical changes in practice. Many attempts have been made to develop new furnaces or processes for smelting iron-ore concentrate not suitable for blast-furnace use, but these processes have gained little importance. It is, therefore, the endeavor in beneficiating iron ore to make a product that will give at least as good results as direct furnace ore in existing blast furnaces. The term "beneficiation," as applied to iron ore, does not necessarily mean concentration, but more accurately means "dressing up" the ore so that it is more acceptable to the blastfurnace operators. In modern blast-furnace practice the structure of the ore is quite as important as the chemical analysis. Certainly, the higher the iron content and the lower the silica, phosphorus and sulfur, the more desirable the ore bccomcs; but if the structure is bad, that is, if the blast-furnace gases can penetrate the charge only with difficulty, the ore is undesirable regardless of its analysis. This means that the ore should be as uniform in size as possible and free from fines, and also that the individual particles of ore should be pervious to the reducing gases of the furnace. Structure and purity are the primary requirements for a furnace ore and structure is just as important as purity. Iron-ore beneficiation processes can be divided, therefore, roughly into two main classifications: (1) processes that primarily improve the structure, and (2) processes that primarily improve the chemical analysis. During the past 10 years approximately 25 per cent of the ore shipped from the Lake Superior district has been beneficiated. Of this about half has been crushed and screened, a simple operation that primarily improves the structure but in some cases also improves the analysis slightly. The other half of the shipment of beneficiated ore, amounting to an average

Jan 1, 1935

Jan 1, 1935

By R. M. Brick, Arthur Phillips, A. J. Smith

A PREVIOUS publication1§ has described the effect of quenching stresses on the lattice parameter values of high-purity aluminum-copper alloys particularly with reference to the solution and precipitation of CuA12. A similar study has been made of the aluminum-rich aluminum-magnesium alloys. Attention has been directed in the present investigation. to the magnitude of the quenching stresses as affected by the specimen size and shape, the number of solute atoms and the quenching rate. The effect of cooling stresses in causing plastic deformation or cracking has been considered in relation to the physical properties of the alloy. On reheating alloys in the two-phase field, the time required for precipitation to occur has been observed in connection with the degree of supersaturation, the rate of diffusion of the solute atoms as a function of the comparative atomic radii, degree of strain, temperature of reheating and grain size. A few qualitative comparisons on the relative effect of these factors have been drawn between the aluminum-copper alloys and the aluminum-magnesium alloys. STRAIN IN SOLID-SOLUTION ALLOYS A 10 per cent magnesium alloy in the form of chill-cast bars was furnished by the Aluminum Company of America through the courtesy of L. W. Kempf. Additional alloys were prepared using aluminum (99.95 per cent Al) and high-grade magnesium. The alloys listed in Table 1 were melted in an Acheson graphite crucible under a flux of fused MgCl2, CaC12, NaCl. Chill-cast rods were sealed under vacuum

Jan 1, 1935

By E. S. Rowland, Clair Upthegrove

The widespread interest in the alloys of beryllium with copper is due principally to the fact that certain compositions show very favorable precipitation-hardening characteristics and are, in fact, the stronges nonferrous alloys known at the present time. Investigations have been conducted by Masing and Dahl and others on the physical characteristics of ternary beryllium alloys, in an attempt to produce precipitation hardening effects with a smaller amount of beryllium than that required in the binary copper-beryllium alloys (2.0 to 2.5 per cent Be). The results of these investigations show that ternary alloys of beryllium with Cu-Sn, Cu-A1 and Cu-Zn, among others, exhibit promising improrcmc~nts in physical properties after precipitation-hardening treatment and, while the increases in properties obtained are not as high as those reahzed from the binary copper-beryllium alloys, excellent properties arc obtaincd with beryllium contents averagirlg about one-half the amount reqnired in the binary alloys. This paper presents the results of an investigation of the equilibriun relations of certain alloys containing copper, tin and beryllium. The alpha-phase boundary of the ternary system is given for alloys containing from 0 to 1 per cent beryllium. The equilibrium conditions beyond the alpha-phase boundary are presented for alloys containing up to 32 per cent tin and 1 per cent beryllium. The data were collected by means of quenching experiments, microscopic examination and thermal analysis The results of some powder-method X-ray determiniations on the alloys, conducted by Mr. William Mikulas and Prof. Lars Thomassen at the University of Michigan, are used as evidence in this paper. The con

Jan 1, 1935

By Russell W. Dayton

The metallurgical polarization microscope has been utilized in several researches in the last few years, thus attaining a fair degree of prominence, but little has been written in a manner suitable to a metallurgist concerning the theory of this instrument. In this investigation the theory was carefully studied, and the results are presented here in a detailed manner, yet as simply as possible. The theory is discussed with particular reference to the three chief functions of the instrument: (1) determination of anisotropy; (2) effect of strain; and (3) identification of inclusions. Each of these is investigated experimentally, with especial attention to the mechanism of producing any effect. Where possible, the discussion is supplemented by photomicrographs. The instrument used had numerous defects as a polarization microscope; these and their remedies are discussed. In the microscopic study of transparent mineral sections (chalcography) the use of polarized light has aided tremendously in the identification of a mineral. The determination of strain in transparent substances (photoelasticity) by the use of polarized light has lately become a commercial process, used in testing finished glass articles. The success of the use of polarized light with opaque materials has not been so great. The magnitude of the effects obtained is much less than that of the corresponding effects with transparent materials, and the mechanical difficulties are much greater. Königsberger,"' i in 1909, was the first to apply polarized light to the microscopic study of opaque substances; Endell and Hanemann(2) were the next, in 1913. In 1919 and 1920, Wright(3,4) prepared two papers on the subject. In the first he developed the detailed mathematical theory from the viewpoint of the electromagnetic theory of light, and in the second described the various methods in use, giving improvements of his own. Schwarz(5)

Jan 1, 1935

By H. B. Fuqua, B. E. Thompson

The area discussed in this paper, commonly known as the West Texas district, is easily divisible into three geologic provinces, the Midland Basin to the east, the Delaware Basin to the west and the West Texas structural platform separating these two. Production in Garza, Scurry, Mitchell, Howard, Glasscock, Irion, Reagan and central Crockett counties is associated with the east flank of the Midland Basin. That in Loving and Reeves counties is associated with the Delaware Basin. All other production and developments discussed in this paper belong to the province of the West Texas structural platform. Because of certain developments that have occurred during the past year, it has been found necessary to slightly revise one of the fields as grouped by Mr. Reith in last year's paper1. The Scarborough-Leck field has been broken down as follows (Table 1): The Leck field is shown separately because it is producing from dolomite; while the Scarborough area, producing from sand, is regrouped and designated as " Scarborough-Kermit-Halley," which includes the producing sand belt across Winkler County from Ward County to New Mexico. It is believed that this is a more logical division of Winkler County and that considerable future work will be avoided by making this change before further production figures have accumulated under the present set-up. A number of new fields are listed in Table 1, some of which may represent extensions of other produeing arras. The authors, however, are inclined to believe that they represent new fields. In either event, less work is involved ill adding two areas together, if they later prove to be one, than in attempting to separate a maze of production data into two fields after they have been erroneously carried as one for a number of years. The Howard-Glasscock field is designated in this review as the Chalk-Roberts field and the Denman production on the Howard-Mitchell County line is included in the Iatan field. Development during 1934 Development in West Texas during the year 1934 showed a marked increase over the previous year both in exploration and ill exploitation

Jan 1, 1935

By Theron Wasson

Discoveries in Michigan, which at the beginning of the year 1934 indicated possible new areas, did not develop into fields of market-breaking proportions. Hart, Oceana County, developed small production from the Traverse lime. Edmore, Montcalm County, proved a small area for oil from the Traverse. West Branch, Ogemaw County, previously reported as Ogemaw, had quite a drilling campaign but was somewhat disappointing because wells were small and erratic. During the year, 30 wells were completed at West Branch, and at the end of the year 15 others in and around this field were under way. At West Branch the Traverse lime, found at 1800 ft., has thin porous streaks near the top, which make small wells; the Dundee lime at 2800 ft. produces from a porous zone of varying thickness. Over the entire field the Dundee wells average 10 to 20 bbl. per day. Acid treatment has materially increased production from some Dundee wells in this field. About 3000 acres have been proved productive from the Traverse and Dundee. At the close of the year the well in Beaverton township, Gladwin County, is probably the most discussed of any in Michigan and may be opening a new field of some proportions. It had an initial production of 70 bbl. daily from the Dundee lime at 3830, which has decreased to 25 bbl. per day. Deeper drilling into the lime may increase production. During 1935 the area around this test will probably be the most active in the state. Structural conditions in Gladwin County, as in other parts of Central Michigan, are obscured by a thick mantle of glacial drift and it will take considerable drilling to outline subsurface conditions accurately. The most important new shallow gas area of the year is around Edmore in Mecosta and Montcalm counties. Eight wells have been drilled to the Michigan stray and the upper Marshall sand, having a combined initial production of 30 million cubic feet. These gas wells are scattered over so wide an area that an estimate of proven territory cannot be made until more drilling is done. At the present time no gas is being sold from Edmore.

Jan 1, 1935

By Walter Kauenhowen

The production of crude oil in Germany during 1934 totaled about 2,200,408 bbl., a 33 per cent increase over the 1,670,109 bbl. produced in 1933. This is an extension of a yearly increase which has continued uninterruptedly since 1928. Producing Fields The 1934 increase in production is due chiefly to developments in the north district of the Nienhagen field, where the production in 1934

Jan 1, 1935

Jan 1, 1935

By John R. Freeman

THIS paper relates entirely to the casting of brass under fluid pressure in steel dies Die castings of metals and alloys of low melting point have been available for many years but the development of brass die castings has been relatively recent, occurring within the past five years The successful development of brass die castings has resulted from the availability of alloy steels that would give satisfactory life as dies and the development of suitable die-casting machines The melting point of copper is 1084° C (1983° F ) and of a high brass about 900° C (1652° F ), as compared to 327 5° C (6215 °F) for lead, 419 4° C (786 7° F) for zinc and 658 7° C (1217 7° F) for aluminum, temperatures that ale indicative of the casting temperatures required for the various types of alloys, of which the melting points are somewhat lower than those of the pure metals TYPE OF DIE-CASTING MACHINE In the well-known plunger and gooseneck types of die-casting machines used for casting the alloys of relatively lower melting point, much of the working mechanism is immersed in the molten alloy For alloys having the relatively high melting point of brass, this obviously is impossible Machines with a separate melting chamber are essential Two rather distinct types are in extensive use at the present time, the Pack and Polak machines, the former designed by Charles Pack and developed at the American Brass Co , the latter developed by Zoseph Polak, of Prague, Czechoslovakia The principles of operation of these machines have been described in articles by Pack1,2,3 and by Sieg 4

Jan 1, 1935