Search Documents

By F. D. Wright, H. D. Fara

The solution to the plastic and elastic stresses around a circular shaft in a hydrostatic stress field that has appeared in two editions of a widely used book on rock mechanics1 is in error. Although this is a relatively minor matter, the correct solution was not found by a literature survey, so it appears worthwhile to present it. For a homogeneous, isotropic, rigid plastic-elastic body in plane strain which obeys Tresca's yield criterion the following equations must be satisfied:'," In the plastic zone,

Jan 1, 1963

By R. C. Craze

This paper discusses the characteristics of the velocity logs now available to the petroleum industry, and some of their advantages and limitations. The velocity log was designed as an aid to the geophysicist to determine velocity layering in the earth and to provide fast, accurate and economical vertical travel time data. After a number of logs had been made, studies were carried out on their use ia correlating strata in adjacent wells. It was found that adjacent strata usually show sufficient velocity contrast to make it possible to correlate these from well to well, even in areas where electric or radioactive logs fail.' In addition, velocity logs have been useful in the determination of porosity and thickness of reservoir rock.' These uses for velocity logs require an understanding of the characteristics of the log in response to the changes in velocity and in borehole conditions encountered normally in logging. GENERAL DISCUSSION OF INSTRUMENTATION The measurement made in velocity logging is more accurately described as a measurement of time rather than velocity. Ideally the log is obtained by measuring the length of time required for compressional sound waves to travel through a fixed distance in the formation. In practice, the time measurement may be made accurately but the distance through which the waves have traveled may vary slightly. Changes in borehole diameter are responsible largely for the difficulty in maintaining a fixed distance, especially if the diameter variations are so abrupt and frequent that the borehole instrument cannot follow contours of the hole. Several service companies have velocity logging equipment available or under development which have different transmitters, receivers, and measuring systems. While these differences are important, there are actually only two systems in use at the present time (Fig. I)."' The first system initiates a pulse at a trans-mitter and detects it at a single receiver. The transmitter and receiver are separated by a fixed distance, called the spacing. The time measured is that between the initiation of the pulse and the first arrival of acoustical energy at the receiver. The second system uses two receivers and a transmitter. The receivers are separated by a fixed distance and the time between arrivals of energy at the two receivers is measured. Here, the spacing is the distance between receivers. The two systems have much in common for it is possible to record both logs simultaneously. Usually the transmitter is an electro-mechanical transducer which produces discrete

By Raymond Franz

Of the many types of capital equipment found in a surface operation, draglines and mining shovels are probably subjected to the most severe service. Yet, some excavators have seen a generation or more of continuous service-proof, if any is needed, of their ruggedness. To keep these expensive pieces of machinery operating, a continuing maintenance program which includes field weld repairs is essential. During an excavator's working life, minor cracks may appear in parts of the steel structure, caused by fatigue and sometimes material defects-defects so small they could not be detected during manufacture.

Jan 6, 1978

By E. J. Haug, K. L. Clifford, K. L. Purdy

St. Joe Minerals Corp.'s Southeast Missouri Mining and Milling Division produces lead, zinc and copper sulfide concentrates at three of its operations. The Viburnum and Fletcher mills have been described in previous papers. The new Bushy Creek mill, dedicated in May of 1973, is an updated version of the Fletcher mill incorporating 8.5 m3 (300 cu ft) lead and zinc

Jan 2, 1979

By D. Harker, W. E. Seymour

CERTAIN alloys of iron and nickel, when rolled and annealed, possess a preferred crystal orientation: (001) in the rolling plane and [loo] in the rolling direction, when recrystallized at 850" to 1050°C after approximately 98 pct cold reduction. Since the preferred orientation makes a direction of easiest magnetization coincide with the rolling direction, these alloys, especially a 50 pct iron in nickel alloy, have found wide application in the electrical industry' for choke coils and special types of transformers. The rate of the recrystallization reaction was studied at temperatures ranging from 500° to 600°C. The heat of activation for the reaction was calculated from the observed rates, and crystal orientation determinations were made before and after re-crystallization. A vacuum melted iron-nickel alloy* analyzing 49.6 pct nickel, 0.018 pct carbon, and 0.30 pct manganese was used for the experiments. The alloy was cold-rolled 98 pct into strips 1/2 in. wide by 0.002 in. thick. Specimens 1 in. long were sealed under a vacuum (approximately 10-8 mm Hg) in 1/2 in. ID pyrex glass tubes. For heat treatment these tubes were fastened to Nicrohm wires and submerged in a molten salt bath controlled to ±2°C. (The maximum measurement error was within 3°C.) The time at temperature was varied logarithmically from one sample to another, and runs were made at 500°, 525", 550" and 575°C. A molten lead bath was used for a run at 600°C which was controlled to the same accuracy. To determine the extent of recrystallization after a particular time at a given temperature, a method was used suggested by the work of Decker, Asp, and Harker.3,4 This method employs an X-ray spectrometer whereby X rays are diffracted from crystallites whose diffracting atom planes are parallel to the rolling plane of the specimen. The intensities of the diffracted rays are measured by a Geiger counter. The counter can be rotated through a range of angle, and can be motor driven through this range at a speed of 2" per min. The measured intensities are plotted vs. angle by a potentiometer recorder. In a 50 pct iron-nickel alloy it was found that only (200) reflections were obtained from the rolling plane with recrystallized material, and that only (220) reflections were obtained from the rolling plane with unrecrystallized material. No other reflections were obtained under these conditions over a range of Bragg angle of 0 to 45" using either type of specimen. As a consequence, the intensity of the (200) reflections from the rolling plane was taken to indicate the amount of recrystallized ma-terial present in a specimen, and the corresponding intensity of the (220) reflections was taken to indicate the amount of unrecrystallized material present. To insure flatness and proper alignment of the reflecting specimen in the spectrometer, the sample was laid in a slot 1/2 in. wide x 0.001 in. deep which was machined in a 3/4x2x1/2 in. steel carrier. The specimen then was taped down with cellophane tape. This steel cradle was mounted vertically in the specimen holder of the spectrometer so that the bottom edge of the carrier rested against a horizontal shoulder. Intensity data used in plotting the percent of recrystallized material vs. time at temperature were obtained by directly counting the diffracted beam of nickel filtered copper Ka radiation used throughout the work. The X-ray spectrometer was employed also in obtaining pole figure data to be used for orientation determinations. At the beginning of this investigation a transmission pole figure holder was used." As a thickness of 0.002 in. of this alloy was found to be opaque to the copper Ka radiation, it was necessary to reduce the thickness of the pole figure specimen. A cold-worked sample was etched in a 50 pct HCl solution for 5 min and was found to transmit a

Jan 1, 1951

By Cyril Smith

IN the study of the structure or the properties of a series of alloys or nonmetallic compounds, it is often advantageous to express the com-position not as percentage by weight, according to which the material is always made up and analyzed, but as the atomic percentage of the two constituents. The conversion from the one to the other is repre-sented by the formulas: 100A 100x or 1 x/A+100-x/B B(100-x) _ 100yA 100y [2] X. yA + (100 - y)B or y (100 - y) where x and y are the weight and atomic percentages respectively of the element of atomic weight A, and (100 - x) and (100 - y) are the per-centages by weight and by atoms respectively of the element of atomic weight B. While calculations according to these formulas are simple, they are time consuming if several conversions have to be made. In 1931 Water-man1 constructed a nomograph for performing the conversion, but this did not permit an accuracy greater than about 1 per cent to be obtained in the neighborhood of 50 per cent. Ölander2 has proposed a graphic method simpler than Waterman's and one that gives a uniform precision throughout the entire scale. The possible accuracy is about 0.5 per cent of the whole, depending on the size and accuracy of the coordinate paper used. Recently, Hermann3 has described a slide rule for making the calculations. These devices make use of the simple rearranged equation

Jan 1, 1933

Joseph HartshoRnE, Pottstown, Pa.: I have read Professor Akerman's valuable paper with great interest. Few of the present generation of American steel metallurgists are aware of the very important part taken by Swedish engineers in the successful development of the Bessemer proeess, and I am afraid some of the older ones have forgotten it. Certainly, I think, most of us would have said that Terre Noire was the first to introduce the use of metal direct from the blast-furnace. It is very well, therefore, that honor should be given to whom honor is due. I can speak from personal experience upon one part only of Prof. Akerman's paper; namely, the effect of the temperature at which the molten metal is cast upon the quality of the finished steel. In a general way I have, of course, known for a long time that the

Jan 1, 1894

By R. J. Wasilewski

Electrical resistivity variation with temperature was measured on a series of alloys containting up to 33 at. pct of oxygen over the range 77° to1500°K. The resistivity behavior is highly anomalous and itzconsistent with simple metallic conduction. Both composition and temperature-depended resistivity singularities were observed. A few experiments carried out on Ti-N and Zr-O alloys indicate the presence of similar anomalies. These observations, together with the published data on effects of substi-tutional alloying on the resistiuity of titanium, suggest that the anomalies are inhevent in the electron structure of this group oj metals. The existence of two-band conduction, and a significant shift of bands relative to each other with temperature and/or the electron concentration are suggested. CONSIDERABLE advances have been made in recent years in the alloy theory of simple metals. Very little, however, is known about the bonding in transition metals and their alloys.&apos; Titanium, with its relatively few electrons, may be expected to show simpler alloying behavior than the more complex transition elements. Its alloys with the interstitial elements appear particularly attractive in an investigation of bonding characteristics because of a) the simple nature of the solute elements, b) the remarkable similarity between the equiatomic structures Tic, TiN, and TiO, and c) the extensive solid solubility ranges of oxygen and nitrogen in a titanium reported.2,3 The Ti-O system was chosen for the most extensive investigation because of the relative ease of preparation of suitable specimens. Since the main object of the work was to obtain data on the bonding and its changes on alloying, electron-sensitive properties were primarily investigated. The present work describes the investigation on the electrical resistivity-temperature-oxygen content relationships. A few experiments were also carried out at selected compositions in the Ti-N and Zr-O systems. EXPERIMENTAL Materials and Method. Polycrystalline specimens were prepared in the form of hairpin strips some 50 by 5 by 0.15 to 0.50 mm by direct metal-gas reaction. This was carried out by controlled oxidation followed by a homogenizing anneal at a higher temperature. All the test specimens were fully homogenized as judged from the uniform microstructure and microhardness. To avoid preferred orientation, each strip specimen was annealed in the ß range prior to the oxidation, this procedure assuring random orientation in the strip;4 hence any texture resulting from the oxidation reaction itself affected all the specimens to a similar extent. Titanium used was of high purity (66 DPN, 10 Kg load; major impurities 0,-43G ppm, N,-70 ppm, C-25 ppm, Fe-14G ppm). The solute content of the alloys was determined by weighing, after the reaction with a known amount of oxygen. The specimens in which the discrepancy between the volumetric and gravimetric measurements exceeded 2 pct (or 0.2 mg for the low oxygen alloys) were rejected. The mean between the two measurements was then taken as the oxygen content of the alloy. Check analyses showed no measurable nitrogen contamination. All oxygen contents are given in atomic percent. Zr-O alloys were prepared in identical manner from hafnium-free crystal bar metal, cold-rolled to strip 0.25 mm thick. Ti-N alloys required very long reaction times at the maximum temperature available (1250°C). In order, therefore, to detect possible oxygen contamination, duplicate specimens were reacted in every experimental run, and one of these was analyzed both for oxygen (vacuum fusion) and for nitrogen (Kjeldahl). Only the specimens in which the check analysis showed < 1000 ppm O were then used for resistivity investigation. Since only relatively high nitrogen alloys (7.1 at. pct; i.e., 2 wt pct N,) were investigated, this oxygen contamination was considered permissible. Dc resistance was measured by the four-probe method as previously described.= The temperature was determined with a calibrated thermocouple placed in the center of the specimen hairpin. The errors in the specimen resistance values thus obtained were estimated at 1 pct due almost exclusively to the finite thickness of the potential wires and the consequent uncertainty as regards the true resistance length of the specimen. For the calculation of the specific resistance, however, no dimensional measurements could be carried out on most of the

Jan 1, 1962

By H. Fechtig, R. H. Buck, A. G. Guy

MULTIPHASE diffusion has been studied for many years in two-component systems1,2 and many of the experimental aspects are now fairly well understood.314 Although by no means all of the problems connected with the two-component case have been solved,&apos; attention has recently been directed to the more complex situation involving three components. The pioneer work of Clark and Rhines6 yielded a qualitative picture of the types of behavior that can occur, and Clark7 has suggested conventions for describing the various phenomena. Kirkaldy and co-workers8,9 have made quantitative studies in several ternary systems and have offered explanations of the occurrence of isolated and nonisolated precipitates. At present, however, there is no comprehensive theory for the variety of phenomena observed in ternary, multiphase diffusion. By analogy with several studies that have been made of multiphase diffusion in the binary Cu-Zn system,2&apos;10&apos;11 a similar exploratory study was made of Cu-Zn-Ni alloys lying along the line in the ternary diagram from the point 80 Cu-20 Ni to the zinc corner of the diagram, Fig. 1. A principal question to be answered was whether initially plane interfaces would remain plane during the course of one-dimensional diffusion. The diffusion specimens studied are described in Table I. The five separate alloys from which they were made were melted in evacuated Vycor capsules from 99.9 pct purity copper, zinc, and nickel. Since some of the alloys were too brittle to be swaged, all of the alloys were used in the cast condition. To facilitate later homogenization, the molten alloys were solidified by plunging the capsule in water. Homogenization heat treatment was done at 720°C for 20 hr. The five nominal compositions in weight percent zinc and nickel, respectively, were: 37.5, 12.5; 44.0, 11.2; 50.0, 10.0; 55.0, 9.0; 65.0, 7.0. Ln Table I the alloys are identified only by their zinc content. Sandwich-type diffusion specimens were prepared by pressure welding disk specimens, each about 3 mm high by 10 mm in diameter. Welding was done in a special threaded vise which was heated at 500°C for about an hour in an atmosphere of flowing hydrogen. A measurement of the separation of the phase interfaces was made on a polished flat on the welded specimen, and then the specimen was sealed in an evacuated capsule and given the diffusion treatment shown in Table I. The diffused specimen was sectioned longitudinally

Jan 1, 1965

By Frederic Dewey

IT IS common to blame irregular assay results upon volatilization and much has been written upon the subject, but there is no. real evidence that, in a properly conducted assay, the loss of either gold or silver by volatilization is sufficient to affect appreciably the result, even when, arsenic or antimony may be present. Bulk assays of flue dust from assay muffles have been published, but the data given are totally insufficient to even approximate the volatilization from a single assay; and such figures as we have indicate the volatilization to be extremely small. Diligent search in the literature and wide inquiry among assayers and instructors have failed to produce a single case where the litharge volatilized in making an assay has been collected and assayed for gold and silver. Having attempted to do this, with most indifferent success, I am not surprised that this has not been done. While various textbooks give volatilization as a cause of loss in cupellation, it may safely be said that in the rare cases where this volatilization is sufficient to affect appreciably the result it is due to excessive temperature. Percy1 says "The loss of silver by volatilization during cupellation is very slight (unless the temperature has been much too high), and may be disregarded." This statement is repeated by the Beringers2 and Smith,3 who includes gold with silver. Mitchell4 says the litharge fume rarely contains over one ten-thousandth of silver. Campredon5 says that at a proper temperature no silver is lost by volatilization.

Jan 2, 1920

By C. R. Forbes, J. C. Barton

Many different shapes of drill bits are in use with hammer drills, but little definite information is available whereby to judge which one of these shapes is the best. The following investigation was undertaken in order to determine what effect, if any, the shape of the cutting edge has on the cutting speed and wearing qualities of drill bits. The bits tested were those in common use, namely, the 4-point or cross bit, the 6-point bit, the Z bit and the "Carr" bit. The rock in which the tests were made was the red granite from southeast Missouri. It is a coarse crystalline granite containing an unusually large amount of quartz and is extremely hard, and on account of its uniform texture is admirably adapted to this work. While tests in other rocks might show somewhat different results, nevertheless it is the opinion of the authors that the relative cutting quality inherent in the shape of the bits would be the same in all rocks. Other qualities, such as mudding freely, freedom from fitchering, etc., might make one bit more desirable than another in softer rocks. Description" of Bits Tested &apos;I&apos;he 4-point bits were the usual shaped bits commonly made on the Leyner sharpener, with 14&apos; taper on the wings and a 90" angle between cutting edges. Some tests were run at 85 Ib. pressure with a 4-point bit made with a 50 taper on the wings; this bit was formed with the Carr bit dies. The 6-point bits were the usual shaped bits made on the Leyner sharpener. The Carr bits were made with a 5º taper and an angle of 100" between cutting edges.

Jan 1, 1918

By A. T. Yu

From the very beginning when an ore body is blocked out, till the last ton of mineable ore is shipped to the smelter, consciously or not, a mining engineer is incessantly wrestling with the materials- handling problem. In the mine and the plants, over the haulage routes, and at the shipping terminals, his fundamental responsibility is to see that each ton of ore and/or waste is extracted, processed and moved easily and economically. Success or failure of many a mining enterprise often rests principally with the judicious and effective application of existant materials-handling technique or its innovation. Time and again, key innovations in practicing techniques have turned a losing venture into a successful and profitable one.

Jan 6, 1967

By Samuel L. Hoyt

Cemented tungsten carbide, a product of a branch of metallurgy which has never possessed more than a relatively minor interest and importance, has recently commanded the attention of engineers, industrialists, financiers and men of business. New methods, new opportunities, new goals, never before considered, have suddenly been brought within the scope of practical realization. It is these results that attract the interest of the world, but we, as engineers and metallurgists, will have equal interest in the product itself and in that branch of metallurgy from which it comes. It seems appropriate, therefore, to speak today on Hard Metal Carbides and Cemented Tungsten Carbide, as the latter represents one of the outstanding developments of recent date in non-ferrous metallurgy. We are interested in the hard metal carbides as a group of related metallic substances and in cemented tungsten carbide as the leading representative of the metallurgy of this group. The literature of this general field is limited, and, bearing this in mind, it seems advisable to attempt to cover the field broadly and to correlate the subject matter, rather than to present a detailed account of any one of its phases. Our annual lecture lends itself admirably to this plan. The quickened interest in cemented tungsten carbide, once its potentialities were recognized, the many sides to the problem of developing the manufacture and use of this new product, and the desire to economize as much as possible in the time of development, have brought many into this work, both in this country and abroad, notably the Osram Lamp Co. and Friedrich Krupp in Germany and the General Electric Co. in this country. It would be presuming too much to attempt to speak too broadly of the present state of the art and science of the hard metal carbides and my remarks arc guided largely by the work done in the General Electric Co., and by our associates in the Carboloy Co. Even here the activities of many in these two groups have centered around the utilization of cemented tungsten carbide, which is outside the scope of this talk. To those whose work is represented in this lecture, it is my pleasant duty to acknowledge their assistance and advice. To Dr. Zay

Jan 1, 1930

By Howard Smith

AT the meeting of this Institute in February 1933, I presented a paper on potash development in southeastern New Mexico1, which contained a brief review of the Geological Survey&apos;s 20-year search for commercial sources of soluble potash minerals and of the events, that led to the discovery, exploration, and first development of the deposits in that state. As a more comprehensive review of the subject was published in December2, the present paper is intended only to discuss recent developments in the domestic potash industry, particularly in New Mexico. A summary of the findings of potash in the Permian Basin, by. G: R. Mansfield and W. B. Lang, geologists of the United States Geological Survey, is now in process of publication by the University of Texas and will be omitted from this paper. In New Mexico prospecting for potassium salts during the past two years has increased materially the known area .of commercial deposits; development has resulted in an increase from one to three in the number of shafts and the starting of a fourth; an increase of annual productive capacity to 1,000,000 tons of crude salts, or 250,000 tons of K20; and an increase in annual refining capacity to 140,000 tons of muriate of 62.5 per cent grade. Construction has been completed to increase still further the production of high-grade salts. In California the American Potash & Chemical Co., operating on Searles Lake brines, has increased its plant capacity from about 100,000 tons to 180,000 tons of muriate a year and is now producing soda ash and salt cake in addition to potash and borax. Potash production from cement-plant and industrial-alcohol wastes remains unimportant.

Jan 1, 1935

By G. A. Guess

THIS investigation was started with the idea of determining whether copper-nickel mattes might not have a lower flowing temperature than copper mattes, and thus perhaps aid in accounting for the difficulty so far experienced in attempts at pyritically smelting copper-nickel ores. We have used the term flowing temperature to avoid confusion with the usual melting temperature. The idea at first was that there might be a greater viscosity range in the one matte than in the other. In the early experiments it was in our minds to determine the relative fluidity of the mattes at a given temperature. Looking to this end we tried pouring equal quantities of matte at the same temperature down an inclined graphite slab, and comparing the distances traveled. Results from such experiments were not satisfactory. We next tried pouring equal quantities at the same temperature through a drilled hole in an Acheson graphite crucible, timing the flow with a stop watch, the whole operation being carried out in the muffle. The flowing temperatures of the mattes tried in this way appeared to be about the same, and there was no marked difference in their fluidity when well fused. Oxidation gave some trouble. These experiments finally led to the adoption of the following apparatus which we thought at the time was wholly original with us, but which we have since found was described by W. McA. Johnson.&apos; The tray used was a slab of graphite 8 in. long, 2 in. wide and ¼ in. thick. It had six holes, into each of which sat a cup of Acheson graphite. Centrally in the bottom of each cup was a vertically drilled hole 3/16 in. in diameter and ½ in. long. The mattes to be tested were put into the cups, in a solid piece. The cups were covered with inverted Battersea "A" cups. The tray was put into the muffle of a gas-fired furnace. Supports on .each end held the tray about 2 in. from the floor of the muffle. Udder

Jan 6, 1916

By C. R. Boyd

This section is about fifty miles in length, extending from the semi-magnetic and brown iron-ore deposits, near South Fork of Holston River, on Virginia and Tennessee State line, through Bristol, Tenn., Goodson, Imboden, or Mineral City, and Big Stone Gap, Va., to the Cumberland Mountain, on the line between Virginia and Kentucky. Following a geological section from the southeast for near South Holston River), to the northwest, we encounter, first: The slates of No. III.,* generally dipping southeasterly with a trend of N. 65&apos; E. They ontcrop along the north bank of South Holston River, having a thickness of 375 feet, 260 feet of which, as at Pen Rhyn quarry and the James quarry, southeast of Bristol, is slate of high grade for interior architectural uses. Next northwest is an undulating series, giving surface-exhibits of these slates, alternating with Trenton limestone, for 21/2 miles, to the&apos; line of semi-magnetic red iron-ores and brown iron-ores, of the upper horizon of No. II., generally pitching southeasterly, as though the whole series, including the slate described, formed a great trough, with its middle

Jan 1, 1887

Silver ore was first discovered in 1866 at Manhattan, and a few ore shipments were treated in a mill at nearby Belmont. The district was abandoned from 1869 to April 1, 1905, when rich gold float was discovered on what was to be called the April Fool claim. By early 1906, 4, 000 people lived in Manhattan. The San Francisco earthquake, in April of 1906, caused the withdrawal of capital from Manhattan and most of the mines were shut down. Later that year and in 1907, however, more strikes were made. The camp prospered until the mid-1920s, but a steady production of several hundred thousand dollars per year was sustained even during the great depression. Then, in 1939, Nevada&apos;s first bucket-line dredge was installed below the town and operated until 1947, producing $4.6 million in gold. The Houston International Minerals operation at Manhattan was started in July of 1980 at a throughput of about 545 mt per day (600 st per day). In contrast to the early day underground operations, Houston&apos;s mine is open-pit and processes low-grade disseminated ores. The ore is a metamorphic schist containing 2. 7 g Au and 1. 03 g Ag per mt (0. 08 oz Au and 0. 03 oz Ag per st). Some coarse gold, up to 1 mm in size, is present. Mining and haulage is done by a contractor. Stockpiled mine-run ore is crushed in three stages comprising a jaw crusher and two cone crushers, with screens ahead of the cone crushers. Crushed product, at about 19 mm (3/4 in.) size, is stored in a silo. Grinding is by single stage ball mill with the discharge passing over two hydraulic traps for coarse gold removal. These traps will be replaced in late 1980 by a two-cell Pan American jig treating the cyclone underflow. The jig hutch product, along with the hydraulic trap product that has been stored, will be treated further for gold recovery. The gravity tails will then be cycloned with the underflow being recirculated in the ball mill and the overflow being treated by flotation. A rougher concentrate is made in twelve No. 48 Galigher cells with the float tails being cycloned. Cyclone underflow is refloated in another four No. 48 cells; the overflow is treated in sluice boxes for further gold recovery before being sent by gravity to the tailings pond. Bulk flotation concentrates are cleaned three times with the final concentrate being thickened. The thickener underflow is then batch cyanided in mechanically agitated tanks and washed with barren liquor

Jan 1, 1981

By B. B. Zavoico

Considerable progress has been made during the past year throughout the Russian petroleum industry. Perhaps the most remarkable achievement is the execution of the programs set out by the Central Planning Bureau of the Department of Commerce. These programs have been increased twice during the past operating year, necessitating drilling the richest reserves, instead of developing gradually as originally planned. The fulfillment of the set-out programs during the past few years makes therefore the present five-year plan of considerable importance to the international oil statisticians in approximating actual supply conditions up till 1933. The production of all Russian fields increased by 14,200,000 bbl. as compared with the 1927-1928 operating year, while the next year&apos;s program anticipates a further increase of 15,700,000 barrels. It appears therefore that production for 1932-33 will total 187,000,000 bbl., or approximately double that of the operating year just closed. It is also evident that the old fields are counted upon to produce only about 67 per cent. of the total, the new fields, not yet discovered, to furnish the balance of 33 per cent. The Soviet oil leaders therefore are hoping to have new fields discovered and developed by 1932-33. However, as in the past wildcatting

Jan 1, 1930

By G. R. Gohn, S. M. Arnold

The results of stress-corrosion tests upon several non-ferrous sheet metals are presented in this paper. The metals include tough pitch copper, five binary brasses, two leaded brasses, one copper-silicon alloy, two tin bronzes, and two nickel-silver alloys. The tests indicate that for most of these sheet metals, externally applied bending stresses below the yield point (0.01 per cent offset) do not result in stress-corrosion cracking as determined by the A.S.T.M. Tentative Method of Mercurous Nitrate Test for Copper and Copper Alloys (B 154-41T).~ Only in the cases of low brass, high brass and medium leaded brass, all cold-worked 4 B & S numbers hard, was any corrosion cracking observed below the yield strength, and in all cases such failures occurred at stresses above the proportional limit for these materials. However, when some of the same materials which showed no evidence of stress-corrosion cracking at stresses below the yield strength, are stressed beyond the yield point, stress- corrosion cracking is quite apt to occur. Since experience has shown that some of these materials, particularly the brasses, are susceptible to stress-corrosion cracking under service conditions, these tests would indicate that, besides externally applied stress and corrosion, plastic deformation in addition to that resulting from the original cold working of the material is also required to produce conditions conducive to stress- corrosion cracking.

Jan 1, 1945

By Claudia Gasparrini

Silver occurs in nature in major, minor and variable amounts in a very large variety of minerals and in several mineral species in the same ore. Because these minerals may respond differently to the same flotation or leaching agents, detailed studies to establish the correct silver mineralogy become essential for optimum recoveries in those situations where the silver is treated as a primary product. On the other hand, fine grain sizes, which often affect gold recoveries, are not generally as critical in silver metallurgy, due to the lower market price which allows for more of the element to remain In the tailings before incurring in economical losses.

Jan 1, 1984