Search Documents

By Victor O. Homerberg, Dexter N. Shaw

A study of the correlation of the mechanical properties and of the microstructure with the heat treatment of 60-40 brass has been confined, heretofore, to the rolled or extruded material as received from the mannfacturer. The results obtained by Babson and Buhler,' Bengough and Hudson12 Stead and Stedman,3 and Brayton4 have been confined to the treatment of the material as received. No attempt was made to get the material into a given condition and then to work from this basis. To start with a given structure would have the decided advantage of making the work independent of the original condition, hence, to make the results reproduceable. In a previous paper, it was shown, in connection with the study of the transformation that occurs at about 470" C., that if specimens were quenched to produce the beta structure and then reheated, the beta would begin to break down, at approximately 200" C., into a very finely divided alpha. It was predicted that important results might be obtained if test pieces were to be given a similar double heat treatment and then tested for the mechanical properties as well as a study of the microstructure. The material used in the present investigation was a 3/4-in. round bar of extruded muntz metal of the following composition: Copper, 61.05 per cent.; zinc (by difference), 38.90 per cent.; lead, 0.05 per cent.; iron, trace; tin, nil.

Jan 1, 1924

F. AT. FARMER*, New York (written discussion?)- The paper presents many phases of the welding art concerning which there are very divergent views. In many cases, the wide differences of opinion are based on the results of mechanical tests, but an examination of the mechanical test data discloses a wide variation in character of the tests made and in the details of procedure, so that it is frequently not only difficult to analyze and check the basis of the conclusions but impossible to correlate various groups of test results. It would seem, therefore, that the technique of testing welds is one of the phases of the welding art that should be studied and standardized in order that the results of mechanical tests made by different people may be strictly comparable and have the same significance to all. The vital difference between testing a specimen of steel that includes a welded joint and testing an ordinary specimen is the non-homogeneity of the weld specimen. The weld specimen has at its center a section composed of material that usually has physical, chemical, and metallurgical characteristics distinctly different from the adjoining metal. Furthermore, the section of added metal is more or less irregular and the ratio of added metal to original metal in the section is quite variable. Consequently the details of procedure and of recording data should be more minutely prescribed than in the testing of ordinary specimens. A conspicuous example f a mechanical test that requires standardization is the cold bending test, a standard test for mild steel. With the usual method, the specimen is bent around. a pin of prescribed diameter and, as all specifications usually require bending to 180° without fracture, the manner of applying the load is immaterial because the specimen is ultimately completely wrapped around the pin. But a specimen containing a welded joint at the center will usually not withstand bending to 180° because of the much lower ductility of the deposited metal in the weld. It is therefore obvious that the farther apart the points of support are the greater will be the angle attained before cracking occurs, simply because most of the bending will take place in the original metal. It is therefore highly desirable that there be prescribed a standard test that fixes exactly the distance between the supports, the curvature of the surface of supports, and the relation between this curvature, that of the loading surface, and the thickness of the specimen.

Jan 5, 1919

By ir. H. Eraly

At the Zolder mine a S/7 computer is used for two purposes : - to monitor production at the coal face - to monitor the distribution of mine cars. By using sensors attached to equipment at the coal face and at the loading points, the computer provides realtime information and also summarized reports, which help management to control production better. The computer will display this information to the control room, where two operators monitor all production events and the availability of the right numbers of mine cars at every production face. All benefits obtained from the system are described.

Jan 1, 1977

V. H. GOTTSCHALK, Rolla, Mo. (written discussion*).-In connection with Mr. Waring's quotation of Urbain's work, attention may be drawn to a remark found in the report of the session of the Société de Chimie Physique,1 held in December, 1909, that, while all blendes contain gallium in larger or smaller quantities, those blendes carrying indium are generally free from germanium, and vice versa. Urbain, furthermore, . expresses his conviction that this behavior, being related to the condi-tions of deposition of the ore, should be an important factor in determining the origin and mode of formation of zinc blende deposits., In. searching the literature for the naturally expected sequel to these remarks, there is found a report on the extraction of germanium from blende, after many months' work, on a commercial scale;2 then a paper3 on some Spanish blendes, all containing cadmium, examined by Urbain's 'method (this paper contains, also, very important work on the com-position and color of blendes, as well as on the occurrence of organic .matter and of inclusions in such blendes), and a second paper on Spanish blendes in general, in which this original point of Urbain's concerning the relative quantities of the three rare elements is taken up.4 Angel del Campo finds that of 68 specimens examined, four only were entirely free of germanium, gallium, and indium;. 38 had small proportions, while 19 were notably, and seven relatively rich in the three rare metals. He found the relative frequency to be: gallium in 60, germanium in, 50, and indium in 38; all three occurred in 29 cases; germanium and gallium together in 18; gallium and indium together in four; germanium and indium together without gallium, in none; four had gallium only, three had germanium only, and one had indium only; in 23 it appeared feasible to extract these elements. Finally, it may be worth mentioning that the discovery of gallium in commercial aluminum5 brought forth two

Jan 1, 1918

Jan 1, 1956

By S. F., French

IN reviewing the design of the ore haulage system for the Morenci project, the reader should bear in mind that the railroad and its equpiment cannot be considered as an independent railroad provided only for the purpose of transporting ore from one point to another, but as an integral part of the operation which begins at the electric shovels loading ore at the mine, and ends where the ore, after having been crushed in the primary crushing plant, is deposited in the bins at the secondary crushing plant. Obviously then, the problem consisted of designing a system that would function to the best possible advantage in complete co-ordination with the other units.

Jan 1, 1942

By Ellison C. Means

Many Virginia furnaces are troubled with a small percentage of zinc in their stock, this element being present, although the chemist may have failed to report it, either in the ore or in the limestone.

Jan 1, 1889

By G. E. Archie

THE usefulness of the electrical resistivity log in determining reservoir characteristics is governed largely by: (I) the accuracy with which the true resistivity of the formation can be determined; (2) the scope of detailed data concerning the relation of resistivity measurements to formation characteristics; (3) the available information concerning the conductivity of connate or formation waters; (4) the extent of geologic knowledge regarding probable changes in facies within given horizons, both vertically and laterally, particularly in relation to the resultant effect on the electrical properties of the reservoir. Simple examples are given in the following pages to illustrate the use of resistivity logs in the solution of some problems dealing with oil and gas reservoirs. From the available information, it is apparent that much care must be exercised in applying to more complicated cases the methods suggested. It should be remembered that the equations given are not precise and represent only approximate relationships. It is believed, however, that under favorable conditions their application falls within useful limits of accuracy.

Jan 1, 1942

By Appendix by A. S. Goldoni, R. E. Tate, E. M. Cramer

The diffision coefficient for self-diffision of plutonium in the temperature range 350" to 440°C has been measured by using puZ3 as the tracer isotope. Autoradiopaphic techniques were used to inzlestigate the possibility of grain boundary diffusion, hut only evidence for volume diffusion was found. The least-squares fit of the data gives the .following equation for the diffision coefficient: The computer least-squares technique for fitting the nonlinear equations is outlined. DETERMINATION of the self-diffusion coefficient of the fcc 6 phase of plutonium is in principle a straightforward experimental task. However, the chemical reactivity, the intense @ activity, and the toxicity of plutonium put limitations on the experimental techniques. The technique selected included roll bonding for preparation of the diffusion couples and pulse-height analysis of the @-particle activity to determine the distribution of the PU tracer in the diffusion couples. EXPERIMENTAL PROCEDURE Couple Preparation. Cylinders about 0.5 in. in diam were cast from two special stocks of plutonium, one of which had been enriched in puZ3', as shown in the isotopic analyses listed in Table I. For each roll-bonded composite sheet, a cylinder 0.437 in. in diam and 0.190 in. thick was turned from each kind of plutonium on a lathe in a 98 pct He atmosphere. The two freshly machined cylinders were positioned face to face in a tube of commercially pure aluminum which had been sealed at one end by welding and the assembly was evacuated on a vacuum manifold overnight. The elapsed time between machining the faces of the plutonium cylinders and evacuating the loaded tube was about 15 min. After overnight evacuation of the assembly the indicated vacuum was 1 X 10"5 torr or better. The aluminum tube was then warmed and pinched off with a cold-welding tool. The pinched-off weld was also fusion-welded as an additional precaution against leakage of air into the evacuated assembly. The assembly was immediately heated for 30 min in a 250°C furnace and reduced in thickness by being passed through a rolling mill with rolls heated to 200°C. The rolling schedule (four passes of 100 mils each with a 10-min reheat after two passes) reduced the thickness of the assembly to 100 mils. The rolled assembly was allowed to cool normally in air. The rolled assembly was sheared at the edges and the aluminum peeled from the composite plutonium sheet. The elliptical sheet was about 0.060 in. thick and usually three 0.383-in.-diam disks could be punched from its central portion. The sheet was heated on a hot plate to the ductile low 0 range (140°C as measured by temperature-indicating pellets) before each disk was quickly punched. The quality of the bond in the disks was evaluated by metallographic examination of the scrap sheet adjoining the hole left by the punch. Only well-bonded specimens without oxide in the interface (as indicated by metallography) were considered satisfactory for further use. More than half of the specimens so examined contained sufficient oxide in the interface to be rejected. Diffusion Anneal. Each disk to be diffusion-annealed was wrapped in 1-mil-thick tantalum foil and sealed within a Pyrex capsule evacuated to 1 x 10~5 torr or better. This capsule was then sealed within another Pyrex capsule at a similar pressure. The diffusion anneals were carried out at temperatures between 350" and 440°C in Marshall furnaces adjusted to have a temperature gradient of not more than *1/2"C over a 5-in. length. This gradient was then further smoothed by using a nickel tube as a liner in the furnace. The liner was divided into three longitudinal cavities by a septum of nickel sheet to which two calibrated Chromel-Alumel thermocouples were attached. One thermocouple was used for controlling the furnace temperature by means of a Brown Pyrovane controller equipped with a Capaciline anticipation circuit; the second thermocouple was monitored twice daily with a Leeds and Northrup K-2 precision potentiometer.

Jan 1, 1964

By E. A. Farrell

A comprehensive survey is made of the status of the asbestos industry as it relates to marketing the product. Included are descriptions of the various types of asbestos and the grading and classification systems used. The uses of asbestos, distribution practices, and types of ore bodies are all related to marketing. World production, the producers and their capacities and world consumption for 1966-67 are summarized and statistical data are included. Asbestos is a general term describing a family of fibrous minerals of the serpentine and amphibole mineral groups. Asbestos has a long history going back to the time of the Egyptians, when it was used as a lamp wick. The commercial mining of asbestos started in Canada, Russia, and Africa in the 1800's, and the first asbestos products were made in Italy and Russia. The five main types of asbestos are: chrysotile, accounting for 95% of the total mined, amosite, crocido-lite, anthophyllite, and tremolite. Canada, Russia, and Africa are the major producers of asbestos. The commercial utility of asbestos was at first based on the heat resistance of the fibrous mineral in the form of packing, at the start of the industrial revolution. Its current utility is based more on its ability to reinforce binders such as portland cement, rubber, and plastics. Its inertness to the chemical nature of most binders is unique. Most important is its ability to maintain its reinforcing utility when the product is exposed to weather and soil conditions as in asbestos cement boards and pipe, and heat, pressure, and chemical exposure as in brake linings and gaskets and packings. The mineral asbestos is also unique because its fibrous form permits it to be spun and woven to cloth or formed into paper. Many asbestos applications are critical to national defense and at the present time, there are no satisfactory substitutes. Grading and Classification Canadian chrysotile asbestos fiber is graded and priced by length since basically the longer the fiber the higher the utility. The Canadian asbestos industry does not, however, classify the fiber by direct length measurement, but by a dry screening test. The method is called the Quebec Standard Screen (QS) test. One pound of fiber is mechanically shaken in four vertically stacked sieve boxes. The relative proportions remaining on the sieves defines the grade. The longer the fiber, the larger is the amount that stays on the top coarse screens and the less on the lower, finer mesh screens. Other tests can be used to further define the length distribution of fiber such as the wet screen Bauer McNett and the Suter Webb Comb (3 group only). The Canadian grading system divides the milled fibers into 5 main groups: group 3, 4, 5, 6, and 7, with 3 group being the longest, and 7 the shortest. Each group is further divided to subgrades, identified in each group by the letters A to Z, with "A" the longest and "Z" the shortest. See Appendix 1 for the Canadian QS classification system. The Russians also use the QS test on chrysotile. The Africans classify their chrysotile into grades similar to Canadian. The African crocidolite and amosite, however, are classified into actual length groups such as l to 2 in. and 2 to 3 in. Amosite and crocidolite are generally longer than chrysotile but also more brittle. Milled asbestos is not composed of staple length fibers like fiber glass or cotton, but of a mixture or blend of fibers ranging from long to short. Milled asbestos has a fiber length distribution similar to the particle size distribution of a powder. For example, the longest group 3 chrysotile grades have a high percentage of the longest fibers (1/2 to 3/4 in.) and low percentage of short fibers (0.003 in.). The figures in Table 1 give the approximate length distribution of the longest, middle, and shortest groups. A second and further method of classifying fiber is the degree to which the fiber bundles are separated to form a larger number of smaller diameter bundles. This property is normally described as the degree of fiberization, openness or surface area. Air permeability tests are used to measure surface area. Asbestos pro-

Jan 1, 1971

By R. E. Old

THROUGH the use of pressure and production records, formation properties and bottom-hole sample data, the performance of an oil reservoir may be studied analytically to define and evaluate the natural forces acting on and within the reservoir. Use is made of material-balance methods and the equations for natural water encroachment to estimate reserves. Methods for calculation of pressures are given. A study of the Jones sand, Schuler field, Arkansas, has been made and is given here to illustrate the value of the methods discussed.

Jan 1, 1942

By Walter Crafts, C. M. Offenhauer

IN a previous study' of the carbide phase of chromium steels, it was shown that chromium carbide (Cr7C3) is a more stable carbide than cementite (Fe3C) at tempering temperatures above about 500°C. in quenched steels containing from about r1to 7.5 per cent chromium. Below this temperature the carbide phase was found to consist of cementite in all of the steels examined. In the present investigation it was found that a similar change in the carbide phase takes place in molybdenum and in chromium-molybdenum steels at approximately the same tempering temperatures. The approximate ranges of occurrence of the alloy carbides Cr7C3, Cr4C, and Mo2C have been determined in steels containing up to 5 per cent chromium, 1 per cent molybdenum and 0.60 per cent carbon. The experimental steels were made in small high-frequency furnaces from Armco ingot iron, low-carbon ferrochromium and calcium molybdate and were poured into 2-in. ingots, which were forged to 1-in. round bars. Sections of the bars were heated to the carbide-solution temperature and cooled rapidly to induce austenite transformation at relatively low temperatures. The steels were subject to some segregation, therefore comparatively high temperatures were necessary to dissolve all of the carbides. The microstructure of the quenched specimens was examined to verify the belief that the carbides had been dissolved, and also to determine the nature of the nonmartensitic structure of incompletely hardened steels. Ferrite and pseudomartensite were present in some of the specimens, but all specimens were quenched at such a rate that pearlite was not formed, in order to ensure the formation of the carbides at temperatures lower than about 500°C. It had been found previously' that in chromium steels the chromium carbide could be produced by transformation of austenite in the pearlite range above 500°C., and, in order to start the tempering treatment with the carbide present as cementite, the absence of pearlite was considered to be essential. The specimens were tempered for 64 hr. to permit the formation of the stable carbide. After tempering, the specimens were submitted to microscopic and X-ray examination. The carbides were separated either electrolytically in a 5 per cent HCl electrolyte or with an acidified copper-potassium chloride solution. The crystal structure of the carbide phases was determined by the Debye-Scherrer type of X-ray patterns. The X-ray patterns obtained from specimens near the boundaries between two types of carbides were generally weak and diffuse as compared with the other patterns. For this reason, and because the more soluble components may be masked, the boundaries between the phases could not be determined precisely. However, the X-ray analysis of electrolytically separated carbides has given consistently reproducible results

Jan 1, 1943

By C. Edward Capes

Fine particles in liquid suspension can be agglomerated by a number of mechanisms. Well-known methods include the addition of electrolyte to reduce the zeta potential and allow mutual adhesion arid the use of polymeric flocculants to bridge between the particles. A more recent technique, "spherical Agglomeration", is the subject of this paper. The process involves the addition of a second liquid which is immiscible with the suspending liquid and preferentially wets the particles to cause particle adhesion by capillary liquid bridges. Progress in the application of spherical agglomeration to a number of distinct technological fields is reviewed in this paper. The areas of interest include the formation of dense, highly spherical agglomerates, the separation of solids from suspension and the fractionation of complex, multi-component solids mixtures, such as ores. Some of the more interesting recent applications in the energy and environmental fields, such as the beneficiation of' coal and tar sands, are highlighted.

Jan 1, 1977

By D. H. Gieskieng

THE advent of curved jaw crusher wearing plates made an approach other than segmental layout analysis desirable for prediction of capacities. For some time it had been known that the drawing board capacities of crushers using these plates had to be considerably modified by complicated experience factors to achieve agreement with results. Because these apparent capacities could be readily increased severalfold by minor crushing chamber shape changes, it was necessary that the utmost precaution be taken in predicting capacities of jaw plates modified for nonchoking, special wear characteristics, or any other reason. To this end the laboratory and field tests outlined by the author in a previous paper' were made on Blake-type jaw crushers. The results of these tests were summarized in a simple first degree equation applicable to crushers using either straight or curved jaw plates. This equation first outlines the maximum capacity potential of a given crusher, then reduces this figure in accordance with installation circumstances by means of a realization factor.

Jan 11, 1951

By W. E. Horst

During the past few years of operation at Kings Mountain, N. C., full-scale flotation has generally yielded poorer metallurgical results than those obtained in the laboratory or pilot plant. After 2 min in each size of Denver flotation machine in the spodumene rougher circuit, pilot recovery (41.7 pct) was almost three times that of the plant (13.6 pet) and about twice that of the laboratory (21.0 pet). Pilot and commercial plant data are based on continuous operation, and laboratory results on batch testing of rougher performance. The ore is a pegmatite containing spodumene, feldspar, quartz, mica, and amphibolite. Data were accumulated to evaluate the scale-up relationships between laboratory, pilot plant, and plant flotation cells. Flotation rate constants and dimensional analysis were used to define the relationship existing between flotation behavior and scale of operation.

Jan 11, 1958

By William B. Plank

ENGINEERING educators and industries are worried about the engineering manpower shortage that is predicted as a result of the increasing demand for trained engineers not only by industry but by the armed services. This is in the face of a decreasing supply, as is shown by this and other studies. Not only has the number of entering freshmen been decreasing since 1947, because of a decrease in the number of high school graduates entering engineering, but the total number of high school graduates will continue to decrease until 1958 because of the lowered birth rate during the depression years.

Jan 8, 1951

At their last meeting, the Directors of the Institute passed the following resolution regarding Robert W. Hunt, who was president of the Institute in 1883 and 1906. This resolution was engrossed and presented to Captain Hunt at a dinner given to him in Chicago, December 9, on the occasion of his eightieth birthday. Resolution At that time it was announced that $5000 had been guaranteed as the nucleous of a fund, the income of which will be used for prizes to be awarded each year, under the supervision of the American Institute of Mining Engineers, for the best papers on iron and steel subjects. The Board of Directors of the American Institute of Mining Engineers extend to their distinguished colleague, Robert W. Hunt, a hearty greeting upon his eightieth birthday anniversary. They congratulate him upon his notable achievements as a pioneer in ,the manufacture of iron and steel, and his long and admirable service both as a practical director and as a wise critic and counselor in that art. They remember with gratitude his successful administration, for two separate periods, of the Presidency of the Institute, and they recall with pride the honor conferred upon it through the award to him of the John Fritz Gold Medal. Not least is their satisfaction in the retrospect of forty-four years of his membership in the Institute, with its unbroken record of loyal friendship acid delightful companionship; and they pray, that this record may be continued for happy years to come. In witness whereof, they have ordered this minute to be entered upon the records of the Board, and a copy duly attested to be sent to Captain Hunt.

Jan 1, 1919

By Arthur McKee

As HEAT is the controlling factor in all smelting operations, it will be .most helpful to make a new set of calculations on the basis of a .unit of fuel burned at the tuyeres to carbon monoxide. This ties together the only two factors in this operation that seem to be constant with respect to each other-the fuel at the tuyere and the air or its oxygen content. If our usual smelting operations, using natural air heated to reasonably obtainable temperatures, furnish sufficient heat above this critical temperature for the purpose, it is doubtful whether additions of oxygen will be of marked benefit. A unit of fuel will not produce a single heat unit more if burned with pure oxygen than if burned with natural air and less heat will be available per unit of fuel by the amount of heat that is carried in by the preheated nitrogen in the natural air of the blast. This is more readily apparent if considered in connection with a heat balance sheet per unit of fuel at the tuyere. The heat available in the stack, as shown by the committee's report, is less by reason of the lower fuel consumption per unit of output assumed in this calculation. The balance sheet for enriched air shows a shortage of the amount of heat usually carried in with the blast; also a lack in the hearth of sufficient heat to melt the 18 per cent. additional metal and slag and in the shaft to the extent of the shaft heat required to heat the 18 per cent. additional stock to the melting point. These heat deficiencies are provided for by the largely increased conversion of carbon monoxide into carbon dioxide, which is assumed, as shown by the following figures: Calculation for natural air: Carbon dioxide 18.4 per cent. (after having eliminated the carbon dioxide from limestone) and 20.8 per cent. of carbon monoxide. Calculation for oxygen-enriched air: Carbon dioxide 28.4 per -cent. and carbon monoxide 23.2 per cent. (no carbon dioxide from stone as lime is charged instead).

Jan 11, 1924

By E. R. Haymaker, C. W. Binckley, F. R. Burgess

A method of establishing stabilized back-pressure curves for gas wells producing from formations of extremely low permeability is presented. Actual well performance under many different operating conditions is shown by the stabilized back-pressure curve. By use of the method. it is possible to conduct back-pressure tests with a critical-flow prover on wells that stabilize slowly, and save approximately 88% of the gas ordinarily vented to obtain satisfactory test data, with a great reduction in time required for testing. INTRODUCTION The reasons for establishing dependable back-pressure curves on gas wells have been pointed out by previous publications. The publication most referred to. of course, is the United States Bureau of Mines Monograph 7, titled "Back-Pressure Data on Natural Gas Wells and Their Application to Production Practices". The technique generally established therein has been accepted and used by many engineers; and, when proper tests are conducted, the results can be used for the analysis and solution of several practical problems concerning field operation and development. Even where formations of low specific permeability are encountered, the determination of a well's actual performance by the back-pressure test method permits the engineer to analyze many problems in individual well operation and also to predict necessary future field development. Such problems as the determination of the ability of a well to produce into a pipe line at a predetermined line pressure, the design of gas gathering systems and meter settings, and the determination of the time and the number of wells required to be drilled to meet future market obligations, can be solved, in part., by the use of a reliable back-~ressure curve. In addition, the computed well delivery rates determined by data from backpressure tests ordered by state regtilatory bodies, when compared with the true back-Pressure curve, permit the operator to ascertain whether such data represent unstable or relatively stabilized delivery rates for given pressure conditions of the well. The technique of back-pressure testing, as described in this report, was developed by Phillips Petroleum Company engineers from data obtained during a testing program that started in 1944 and has been continued to date. Three hundred and eleven back-pressure tests were conducted on 299 wells located in the southern part of the Hugoton Field. The gas-bearing zone is composed of several dolomitic formations of the Permian Age; the important ones are the Herington, Upper Krider, Lower Krider, and Winfield. The average bottom-hole temperature is approximately 91 °F.. and the initial wellhead shut-in pressures range from 400 to 440 psig. The spacing pattern is 640 acres per well with each well located near the center of the section. The range of back-pressure potentials on wells tested was from 500 to 23,000 Mcfd. All gas wells were acidized, and the quantity of acid used, expressed in 1574 hydrocloric acid, varied from 12,000 to 22,000 gallons per well. The quantity and concentration of each treatment depended on the stage, the formation being treated, and experience gained from previously completed wells. The gas in the Hugoton Feld is a "dry" gas. It has a gasoline content of approximately 0.25 gallons per thousand cubic feet, as determined by charcoal test, and its specific gravity averages about 0.71 as compared to air (air = 1.00 at 60°F.). Of the wells tested, 71 were completed with 7" casing, 3 with 9 5/8" casing, and 1 with 6%" casing set on top of the upper producing formation with the well bore through the gas bearing formations being open hole. Two hundred and twenty-four were completed with 5 1/2'' O.D. casing set through the gas bearing formations and perforated. For the purpose of establishing reliable back-pressure curves in the area, Phillips Petroleum Company personnel has computed data on the basis of 24-hour flows per point. Early in the program, many tests were actually permitted to flow 24 hours to obtain data for each plotting point, at great expense in man power and time. Presently, however, such tests have been replaced by tests of short duration flows which can be made to effect results that correspond to the tests obtained by flows of much longer duration. METHOD When a gas well producing from a reservoir of low permeability is opened for production through a constant size orifice, both the rate of flow and working pressure decline. first at a high rate and later at a lower rate until after several hours the decline becomes difficult to ascertain. In this paper the rae of flow and working pressure are considered to be stabilized when it becomes difficult to observe changes in working pressure during a period of three hours by the use of a deadweight pressure gage. Stalibization of pressure in the literal sense is never obtained in a producing gas well. In formations of low permeability. such as those in the Hugo-ton Field, most wellhead working pressures approach stabilization closely enough to be used satisfactorily in the determination of a back-Pressure potential curve after flow periods of 24 hours. We shall therefore describe the backpressure curve calculated from ohserved rates of flow and working pressure at the end of 24-hour flow periods.

Jan 1, 1949

By F. L. Sizer

THE mining regulations of British Columbia and Mexico present some features which might well be copied in the United States, if we are to have a complete revision of the laws governing mining titles. 1. First and foremost is the "square" location, which would mean the abolition of extralateral rights. This is a condition in both of the countries above named which has seemed to work no hardship upon any one, and certainly the limitation of underground rights by vertical planes through all lines makes a locator's rights clear. In view of the long and costly litigation which has involved so seriously many of our most important mining districts, it would seem to be the part of wisdom to avoid a repetition of similar trouble on titles of lode mining claims, by the enactment of a law similar to that in force in British Columbia. Objections have been raised by representatives of English companies to the investment of large amounts of money in mining operations in the United States, because of the insecurity of title under the present apex law; and the statement has been made to me personally by one of the largest English operators, that he would never again consent to the purchase of mines in the United States, preferring Mexico with all its revolutionary troubles to the danger of encroachment upon his underground rights by an unscrupulous neighbor. Without going into further argument as to the desirability of the "square location," it should be sufficient to say to those who are inclined to "let well enough alone." and still stick to the "law of the apex" that there have never been any serious objections raised to this feature of the square location in either British Columbia or Mexico. There are well founded and logical reasons for abandoning the doctrine of extralateral rights since it is so difficult of interpretation; the most natural substitute being a law similar to that of British Columbia, giving to each locator an area 1,500 ft. square.

Jan 3, 1914