Search Documents

At its meeting on February 21, 1933, the Board of Directors passed the following resolution defining and expressing the policy of the Institute with respect to official participation or action in controversial matters: WHEREAS, the Board of Directors at its last meeting passed the following resolution: "The Board of Directors, having been appealed to by several Local Sections for advice concerning the attitude and policy of the Institute relating to the endorsement of candidates for public office, the following statement of policy is formulated: "Whereas, the American Institute of Mining and Metallurgical Engineers is organized for purely professional and scientific purposes, and whereas diversity of opinion among its members on partisan or political questions is inevitable, it is the expressed policy of the Institute to refrain from official participation or action in political and semi-political matters." AND WHEREAS, appeals for additional advice have been received: NOW, THEREFORE, IT IS RESOLVED: (1) That the policy of the Institute is to refrain from official participation or action in controversial non-technical economic subjects; further (2) That if any Local Section is in doubt as to the application of this policy to any particular subject, it should communicate with the Secretary of the Institute for advice.

Jan 1, 1940

By Clarence Carleton Semple

At a number of mines in eastern Nicaragua, 3.5- or 5-ft. Huntington mills are used for grinding gold-ore after a pre-liminary breaking in jaw-crushers. The smaller mills are made sectional to facilitate transportation to the more difficultly accessible mines. The capacity of the smaller mills is about 20 or 25 per cent. that of the larger, but in proportion to the quantity of ore ground they require more power and are subject to greater wear. The notes herein given are from records of the performance of the larger mills at one of the mines, but, in general, apply to the smaller mills also. The Nature of the Ore. The ore occurred as a series of flat veins in a' highly-decomposed rock, probably alaskite. The primary mineralizatioll comprised pyrite, pyrrhotite, marcasite, chalcopyrite, and quartz; the oxidation-products of which were chiefly hydrated iron oxide or limonite, chrysocolla, azurite, and malachite. The kaolinization of the feldspar of the country resulted in the admixture of a great quantity of clay with the oxidized ore. The quartz was sandy, imbedded in the clay; and probably the greater part represented the residue from the crushed rock in the fissures after leaching, and kaolinization of the feldspar. There was little vein-quartz in the unaltered primary sulphide ore. Only the oxidized ore was mined for the gold that it contained in amouiits that averaged $4 per ton. No specks of gold mere ever seen in the ore, and the gold obtained by panning was always exceedingly fine. The amalgamation-bullion was about 800 fine in gold and from 60 to 80 in silver. The ore delivered at the mill contained from 5 to 15 per cent. of moisture; during the rainy season the quantity was much greater. The moisture and clay made the ore so sticky that it had to be raked over steeply-inclined grizzlies; it hung in the ore-bins,

Jan 1, 1912

By Henry S. Mackay

The interesting paper recently submitted by Messrs. Tobelmann and Potter1 shows that chemical problems have developed which are of great interest in this new and important branch of metallurgy. Those who realize what a process of this kind really involves will agree that it deserves a better name than '(leaching process." The word leaching conveys the idea that the copper is simply leached out of the ore with acid and then precipitated on iron; the chemistry of such a process would be of little interest. As, however, during the first year's operation of this plant 24,400,532 lb. (11,067,837 kg.) or about two-thirds of the produce, was electrolytic copper, while 7,992,033 lb., or about one-third, was cement copper, it would seem more appropriate to term the process electrochemical. It further appears, from the particulars given, that efforts have been made to have the entire production in the form of electrolytic copper. This could be done if the chemistry of the problem were kept in balance, so that it would not be necessary to discard any solutions that carried copper and acid of commercial value. A process, such as that under consideration, in which the copper is precipitated from solution by electrolysis, the solvent being at the same time regenerated, is one that requires special chemical and electrochemical knowledge and experience if all the copper in solution that has been extracted from the ore is to be successfully and economically produced as electrolytic copper. The object of this paper is to discuss, from the practical and theoretical standpoints, the chemical and electrochemical problems involved in the working of a process of this kind, and which must be solved to keep it in chemical and electrochemical equilibrium. In such a process, if the chemical balance is maintained, a solution can be used alternately as a solvent for the copper in the ore and as an electrolyte of high efficiency for the precipitation of the copper. To maintain the chemical equilibrium and so attain this result, the process must be so controlled that the solu-

Jan 1, 1921

By H. Cecil Spicer

The results described in this article are based on field work conducted during the periods APril-May, 1939, and MaY-JulY, 1940. The United States Potash CO. is mining potash on Government land under a permit from the Department of the Interior and the geophysical investigation mas completed under a cooperative arrangemerit made between that company and the Conservation Branch of the Geological Survey. The writer, a member of the Section of Chemistry and Physics of the Geologic Branch, was assigned to this investigation. Four definite objectives were in mind for the geophysical work in the studies over the salt deposits. The first was to determine the measure of success that could be attained in this type of work with the resistivity methods that were to be employed. These methods had been introduced into the work of the Conservation Branch by Benjamin E. Jones for the investigation of dam sites, and have been used under his direction by the author for such work. If the method proved to be applicable, an l was to be made to contour the top of the salt beds and also the other formation boundaries known to be present in this area. Salt-water aquifers were to be studied in an effort to determine their boundaries, and an attempt was to be made to delineate the potash-bearing beds. Others have made, and reported, resistivity studies over saliferous deposits in different areas. Friedell and Messrs. Schlumberger2 reported geophysical work performed in the disrovery of the salt domes of Alsace; Carrette and Kelly3 described the geology of the same area. Leonardon and Kelly4 published a resistivity curve obtained over the Hettenschlag dome, and a further discussion of this same area was given by the Messrs. Schlum-berger5 in a communication. Messrs. Alty6 described studies 0" salt deposits in which the sing[e-probe method was used. Sinerez7 mentions that electrical methods were tried over salt deposits in Spain. Geoffrey and Charrin8 show a resistivity curve obtained over marl, gypsiferous marl and salt which is similar to that obtained over the New Mexico salt deposits. Kelly9 reported resistivity work performetl with the ground comparator of Zuschlag over the salt deposits near Syracuse, N. Y., where the Salina formation is at a depth of 700 to 800 ft. Some structural studies on the potash basin of Alsace are described by Poldini.10 Another single-probe resistivity study, made over salt deposits in New Mexico, is briefly described by Heiland,ll through the courtesy of Harry Aurand, of the Midwest Refining CO.

Jan 1, 1942

This Association is made up of Alabama members of the following technical societies: The American Society of Civil Engineers, American Institute of Mining Engineers, American Society of Mechanical Engineers, American Institute of Electrical. Engineers, American Chemical Society and the American Institute of Architects. The association organized last winter for the purpose of maintaining an organization among the technical men of the State of Alabama, to stimulate the development of the natural resources of the State, to foster public interest in all things beneficial to the State, to advance the interest of the technical profession in the State and to encourage social intercourse among its members. On June 30, 1917, an excursion was made to the power house of the Alabama Power Co. at Lock 12 on the Coosa River. This is the first meeting held outside of Birmingham and is also the first meeting to which ladies were invited. About 85 members and guests attended and the excursion was voted a great success by all present.

Jan 8, 1917

By Joseph Hartshorne

Ever since the introduction of the Siemens regenerative furnace, it has been recognized that a certain amount of gas is lost each time the furnace-action is reversed. This loss comes, first, from the gas which passes through the free connection between the stack and the gas-main, which exists during the time the reversing-valve is turning over; and, secondly, from the gas which is in the chamber and flues, from the hearth to the reversing-valve, and which flows back into the stack when the valve is reversed. The amount lost each time is, of course, small; but, since a furnace is reversed from four to six times every hour for, say, 300 days in the year, the aggregate is large enough to be well worth attention. The estimate has been published1 that, in Germany aloue, the loss from the first of the above causes amounts to 500,000 barks per year. The loss from the second cause is, of course, much greater.

Jan 1, 1907

By M. W. Strong

THE technique of handling drilling muds varies somewhat, partly because of personal factors but mainly because of differences in forma-tion, the type of problems met with, and the general drilling conditions in different localities. The much greater depths to which bore holes are now carried have made necessary closer attention to and great modifications of all aspects of drilling-mud technique. Increased depth means smaller hole, smaller drill pipe, smaller clearances, higher pumping pressures, higher differen-tial pressures between shows and the mud column, less accurate control of the weight of the mud column, delayed receipt of formation data, and poorer samples. It means longer delays and greater hazards in rectifying mistakes or dealing with accidental occurrences. Equipment on a larger scale is necessary and more pains must be taken with layout. Lastly, the budget costs of raw materials have risen to high figures and economy of time and of direct monetary expenditure have come to mean much more than formerly. A mud laboratory is now part of the essential establishment of a modern oil field and to it current problems can be submitted for the most thorough investigation. The detailed chemical properties of all mate-rials purchased or quarried have to be investigated. Detailed data on the physical properties have to be ascertained and research on improve-ment of material and its most efficient use has to be carried out. In this paper we propose to discuss the main mud problems with which we have to deal in Iran, some of which are peculiar to our local conditions while others are of the general type common to all workers in this subject.

Jan 1, 1938

By N. K. Chen, R. Maddin, R. B. Pond

A METHOD has been described by Andrade' for obtaining very rapid grain growth so that single crystals of high melting point metals could be made with comparative ease. The furnace construction was essentially a very thin wire through which was passed an electrical current so that "a high uniform temperature" was maintained. The wire was surrounded by a fused quartz tube from which the air had been evacuated. Andrade applied this method to the growth of single-crystal wires of alpha iron, and Tsien and Chow2 prepared single crystals of molybdenum 0.25 mm diam in this way. In the present report a method is described in which the basic idea of the Andrade furnace is utilized. However, modifications are employed so that large single crystals of molybdenum or of any refractory metals can be grown. Furnace The modified Andrade furnace is shown in Fig. 1, and the detailed drawing of its construction can be seen in Fig. 2. The furnace proper consists of a 2'/2-in. diam fused silica tube, 20 in. long, which is evacuated continuously at the bottom. Two water-cooled copper electrodes hold the specimen by means of collets held in place in the electrodes by set screws. These electrodes serve also to transmit power to the specimen. The lower electrodes can be clamped to the stand, while the upper electrode is fastened in place to the bellows which in turn is further connected to one side of the lever arm, flexibly supported at the top. After the specimen is mo;nted- and the vacuum is secured, the lever arm is adjusted by means of the counter weight so

Jan 1, 1952

By L. F. Wright

Operations of these two mining companies have some superficial similarities-geographical location, production rates, comparatively large ore reserves; but any critical comparison of mining and milling procedures or of economics must take into account the striking differences in geological environment and mineralogy of the respective ore deposits. The properties are only about 20 miles apart on an upland surface of moderate relief (part of the Interior Plateau of central B. C.) which occupies an area east of Thompson River between the towns of Ashcroft and Merritt. Being in the "dry belt" of British Columbia, water conservation is necessary at both operations.

Jan 12, 1963

By William Catron

BECAUSE the rich La Colorada orebody of the Cananea Consolidated Copper Co. does not outcrop at surface, after its discovery (by churn drill) and before mining was begun, a large amount of development work was done to learn the shape and extent of the ore and to provide for eco-nomic and effective mining. As these openings progressed, the actual shape of the orebody became known and with this knowledge came the realization that mining this rich and unusual deposit without loss of ore or danger to workmen presented several difficult problems. This paper will describe one of these problems; namely, the handling of an inverted cone-shaped core of barren rock, on the periphery of and below which the ore occurred. It was clear that as the ore was mined out from around and under this inverted cone of rock, weighing about 3,000,000 tons, it would hang over the workings, held suspended only by its own tensile strength and threatening to crash into the stopes below with disastrous results to men and mine. The method of mining developed during the years 1928, 1929 and 1930 anticipated and provided for the eventual collapse of this core of rock. In November 1936 the core settled clown gradually on the edges of the stopes, descending a total of about 50 ft. vertically. The men in the stopes had ample to warning and no lives were endangered. There were no air blasts in the mine. The core broke loose from its top support at the 500-ft. level along old fracture planes and evidently is crushed to the ninth level. Movement was of short duration; the following shift went to work in the stopes as usual. No ore was lost.

Jan 1, 1938

By C. E. Lesher

Two processes for agglomerating fine sized ores with low temperature coke are described. One process (Orcarb) agglomerates ores with limited amounts of carbon; the other (ore-carbon pellets) pelletizes fine sized ores, using low temperature cokes as the binder. Data are presented on the products obtained when taconite, magnetite, and hematite concentrates and several titanium oxide ores were used. REDUCTION of finely divided oxide ores has long been a major metallurgical problem. Various methods of agglomerating, notably briquetting, sintering, nodulizing, and pelletizing, have been developed and are in industrial use. Carbon is the usual reducing agent for oxide ores and attempts have been made to agglomerate fine ores with coking coal in order to get the metallurgical advantages of intimate contact and increased particle sizes suitable for subsequent smelting or reduction.1-3 For the past three years, research has been in progress on two processes for combining fine sized ores with reactive carbon in the form of low temperature coke. By one process, designated Orcarb, the ore is coated with coke carbon in amounts limited to that required for reduction and the result is an appreciable but limited increase in product particle size over that of the original ore. The second process, called ore-carbon pellets, produces pellets of fine ore bound by low temperature coke. The first objective was to develop a process for combining an oxide ore with only enough carbon for its reduction, the amount being that derived from the simple reduction equations. The carbon (that amount theoretically required for the reduction of the oxides in an agglomerate with ore), calculated to CO, ranges from 10 pct for zinc calcines Or phosphate Ores to 21 pct for rutile and 26 pct for silica. The carbon required for reducing iron oxides falls between the extremes—10 and 26 pet' When the carbon in the agglomerate is low temperature coke, reduction by hydrogen may be expected to take place, thus modifying the calculated carbon require- ment. On the other hand, in practice, an excess of reducing agent over that required in theory is normally used. Screen sizes of three iron ores on which the greater part of the experimental work was performed are given in Table I. Most of the testing was done with Freeport (Renton Mine) coal, but Pittsburgh and Elkhorn bed coals were also used. The first objective was to agglomerate the ore with sufficient low temperature coke to provide carbon for reduction, i.e., in the range from 10 to 25 pct. This was accomplished by preheating the ore, mixing with pulverized coking coal, and completing the coal carbonization in a plain steel rotating retort. The pilot retort, as it is now constituted, is shown by diagram in Fig. 1 and photograph, Fig. 2. Ore is fed into the upper kiln by a screw; it is heated to 900° to 1100°F by direct flame and it is then discharged into an insulating hopper from which it goes

Jan 1, 1956

By E. J. Duggan

The mine and mill of the Climax Molybdenum Co. are at Climax, Colorado. Climax is on Fremont pass directly on the Continental Divide, at an elevation of 11,400 feet. Description of Ore The Climax ore-bearing rock is essentially an altered and highly silicified granite, fully half of the gangue being quartz. Molybdenite is the only mineral of economic consequence and most of it is intimately associated with quartz in the form of fine veinlets and stringers. Other minerals are molybdite, pyrite, and chal-copyrite. While the molybdite may be readily extracted by hydrometallurgical methods, its content is too low to make such operations profitable. The pyrite content ranges from 2 to 5 per cent and that of the chalcopyrite from 0.03 to 0.05 per cent. There is not enough copper to make its recovery attractive and one of the metallurgical problems is the elimination of it and the pyrite from the product. On account of the close association of the molybdenite with the quartz and the necessity of eliminating the pyrite and chalcopyrite from the final product, fine grinding followed by flotation is the only feasible method of concentration. History Construction of the first milling unit was started in 1917 and it was operated during parts of 1918 and 1919. In the postwar years, there was almost no demand for the product and production was at a standstill until 1924. The Company's research campaign to develop the use of the metal began to show results in that year. From r926 to 1932 production ranged from 500 to 1200 tons per day. In 1931 an additional mill section was built and production was gradually increased until in 1934 and 1935 about 3000 to 4000 tons was milled per day. This tonnage overtaxed the milling facilities, and as the demand for inolybdenum was growing constantly, additional milling equipment was needed. In 1936 and 1937 another crushing plant, six additional mill sections and the necessary auxiliary plants were constructed and brought into operation. This plant was designed to mill I0,000 tons per day, but it was not long before 12.500 tons was being treated during periods of peak demands. During the summer of 1941, to meet defense needs, the mill has been required to treat 15,500 tons per day. This has been accomplished with little plant expansion and at no loss in recovery, as will be described later. TO increase capacity still further, one more primary section is now being built. This will bring capacity to 18,000 tons per day, which can be stretched to 20,000 tons at a small sacrifice in recovery. Crushing There are two crushing plants: No. I, of 5000 tons capacity (flowsheet in Fig. I) and No. 2, of 15,000 tons capacity (Fig. a).

Jan 1, 1943

Papers published by the Institute are issued in a variety of forms MINING TECHNOLOGY, issued every other month, contains the TECHNICAL PUBLICATIONS on Metal Mining, Minerals Beneficiation (milling and concentration), Industrial Minerals (nonmetallic) and Mining Geology, Mining Administration, and Geophysics papers relating to Metal Mining (A, B, H, I, K, L ) METALS TECHNOLOGY, issued eight times a year, contains the TECHNICAL PUBLICATIONS of the Iron and Steel Division and the Institute of Metals Division, and once or twice during the year those on Non-ferrous Metallurgy (reduction and refining of nonferrous metals) (C, E, and D ) PETROLEUM TECHNOLOGY, issued every other month, contains the TECHNICAL PUBLICATIONS of the Petroleum Division, together with Geophysics papers relating to -the finding of Petroleum (G, L ) COAL TECHNOLOGY, issued four times a year, contains the TECHNICAL PUBLICATIONS of the Coal Division (F ) MINERAL INDUSTRY EDUCATION DIVISION papers appear in a TECHNOLOGY according to classification of subject matter DISCUSSIONS appear in the respective TECHNOLOGY as available MINING AND METALLURGY is the monthly magazine, which contains papers of general interest and news of the membership

Jan 1, 1952

By Herman Garlichs

The development of the extensive Southeast Missouri deposits greatly preceded that of the Iowa and Wisconsin deposits. It began about 1720 at Mine La Motte and other localities, and has continued uninterruptedly to the present time. It is estimated that this district produced about 184,000 tons of lead in the year 1916, having a value of approximately $25,000,000. This is a new high record. The Southwest Missouri orebodies were hardly known before 1845 and were not extensively developed until 1870. Lead production in Southwest Missouri for 1916 was 38,788 tons. Oklahoma produced 14,399 tons and Kansas 2,345 tons, making a total for Southwest Missouri, and the adjoining districts in Oklahoma and Kansas, of 55,532 tons of lead. The first metallurgists in Missouri were the Indian and the hunter. The early settler learned to procure his bullets either by melting ore in his camp fire or by throwing pieces of galena on an old stump and depending on the usual roasting and reaction method to obtain the metal. A little more refined method was to arrange two flat stones in the form of a, V. Wood and galena were placed in the furnace and ignited.. As heat developed, some of the metal was extracted and molded into bullets. The next step in utilizing the lead ores was the log hearth. All lead in Missouri was smelted in this crude affair before 1820. It was built on sloping ground, and consisted of a hearth of stone, surrounded on the front and two sides by a stone wall. The wall was 7 it. high in front. The top and rear end were left open and in front an arch or opening was made, forming the eye of the furnace. In front of this a pit was dug in the ground, to receive the molten metal. Large logs were rolled in at the back and made to rest upon ledges formed inside, to raise them from the hearth and to give a draft. These logs filled the entire width of the furnace. Small split logs were then set up around the two sides and the front, and the ore was piled on until the furnace was full. Finally, the mass was covered with logs and fuel until the ore was completely surrounded. A gentle heat was started, which was raised very gradually. After 12 hr. the heat was increased and continued for 12 hr. more, 24 hr. being required for each smelting. The furnace treated about 5,000 lb. per 24 hr. and the ore yielded about 50 per cent. of its metallic lead. A considerable quantity of the ore was not desulphurized, and fell between

Jan 1, 1918

By Maurice E. Peloubet

This discussion of accounting will describe the statements and the information that the accounting system produces, from the point of view of those who use such systems rather than of those who prepare them and who do the detail and technical accounting work. In any well organized mine, quarry, or other enterprise exploiting a mineral deposit, no matter how small, some clerical and accounting work must be done. Miners and other employes must be paid, supplies must be purchased and issued, and various tax and information returns, which even the smallest enterprise must file, have to be prepared. In this chapter it is assumed that the enterprise has employes of this type and that they understand the fundamentals of record keeping and accounting. It would be impossible here to give sufficiently full explanations to enable a man with no previous clerical and accounting training to set up and operate an accounting and cost system for even the simplest extractive operation. Rather, we shall hope first, to tell the investor and the operator, from the chief engineer or president down to a subforeman, what to expect from the accounting statements and records and how to use this information in his daily work; and second, that it will enable the man with some knowledge of accounting or book- keeping, but with little or no experience in any extractive industry, to set up and operate a satisfactory system for a mine or other extractive enterprise. For readers who wish to go further, the bibliography at the end of this chapter contains many references. T he emphasis has, therefore, been placed on the statements to be produced and the purposes for which they are to be used rather than the underlying books and records. These are, with a few exceptions which will be described later, essentially what might be found in any industrial enterprise and would probably, in the extremely small enterprise, consist of handwritten journals, ledgers, analysis books, payroll books, and stores ledgers. In the larger enterprise, various types of mechanical accounting would be introduced in proportion to the complexity of the operation.

Jan 1, 1964

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members.) Members who registered at Institute headquarters during June: Ralph H. Sweetser, Columbus, Ohio. O. M. Bilharz, Rivermines, Mo. Etienne A. Ritter, Colorado Springs. Colo. Joseph A. Holmes, Washington, D. C. Dwight E. Woodbridge, Duluth, Minn. Francis Church Lincoln, Urbana, III. Arthur Chippendale, Mexico City, Mex. William E. Saunders, Philadelphia, Pa. E. T. Miller, Louisville, Ky. E. P. Ross, Johnson City, Tenn. Jesse Scobey, Denver, Colo. H. M. Boylston, Cambridge, Mass. Charles Rhodes, Auckland, N. Z. Edward Keller, Perth Amboy, N. J. John W. Finch, Denver, Colo. F. G. Cottrell, San Francisco, Cal.

Jan 7, 1913

By Frances Jane Cromwell, D. J. McAdam, G. W. Geil

In a series of papers, the authors and their associates have shown that the technical cohesion limit is affected by the same four factors that affect the flow stress, namely, the stress system, plastic deformation, temperature, and the strain rate.16-28 Moreover, each of these factors affects the technical cohesion limit in the same way that it affects the flow stress,t The influence of any one of these factors may be represented by a curve of cohesion limits, although only one point on the curve may represent actual fracture. As the term ilfracture stress' has come into use with the same significance as 'ctechnical cohesion limit," the authors are here using the shorter term with the understanding that it does not always refer to actual fracture. This paper presents the results of an investigation of the flow of notched and unnotched specimens betqrcen yield and fracture, A study has thus been made of the flow and fracture of metals as affected by the stress system, and of the ductility of metals as affected by the stress system throughout plastic deformation. Since two of the principal stresses were equal (S2 = S3), the stress systems can be represented in terms of the radial stress ratio, the ratio of the transverse radial stress s3 to the longitudinal stress S1.* The results of the experiments are represented by a series of their flow-stress curves for each Of the metals investigated, and these diagrams have been used for the development Of Other diagrams Of various types. Ludwik was the first to suggest that fracture occurs when the flow stress becomes equal to a technical cohesion limit. Although Ludwik was incorrect in his view that the technical cohesion limit depends only on the amount of plastic deformation and not On the stress system, he was 'Orrect in his view that the flow-stress curve for any stress system terminates at a point representing a technical cohesion limit. The authors have seen some recent references to assertions by other investigators that a point representing the fracture stress need not be on the flow-stress curve. The Ludwik principle, however, "auld Seem to be axiomatic, provided that the flow Stress and fracture stress are properly defined and that the fracture stress is properly determined. Disregard Of this principle has led to some untenable theories Of criteria for fracture. When a metal is very ductile, the conventional method of determining the ductility and fracture stress by dividing the breaking load by the sectional area after fracture, generally gives values that are much too high. With some metals and in some conditions, the fracture stress thus determined may be two or more times the

Jan 1, 1949

Jan 1, 1970

By R. L. Perrine

This paper presents results obtained by consider ation of unstable miscible displacement within a porous medium as a quasi-turbulent displacement process, that is, a process characterized by fluctuations around a simpler, mean flow behavior. The instability usually results from the miscible displacing fluid having a viscosity lower than that of the displaced fluid. Such instability is evidenced in suitable experiments by the presence of viscous fingering. A unified theoretical relationship applicable to both stable and unstable displacement is derived. Parameters in the theory are obtained by empirical means. Although the theory describes an idealized conceptual model, agreement with experiment is quite reasonable up to moderately adverse viscosity ratios, such as 17:1. INTRODUCTION Many experimental studies of miscible displacement in porous media have been conducted with prediction of reservoir displacement efficiency as the ultimate objective. Most such studies have utilized lower displacing than displaced fluid viscosity, scaled to potential reservoir fluid pairs. Theoretical approaches have been largely limited to unit viscosity ratios, however, in spite of the necessity for an understanding of the mechanism of the unstable, adverse viscosity ratio displacement process. An obvious reason is the difficulty of describing in mathematical form the viscous fingering characteristic of these conditions. Observation of experiments conducted with dyed fluids in transparent systems suggests an analogy between unstable miscible displacement and turbulent flow in a pipe. In both cases there are fluctuations around a simpler, mean flow behavior. An important difference is that flow behavior of interest in the porous medium is entirely transient, contained within a transition zone between displacing and displaced fluids. Transient behavior complicates description in that coefficients in the equations become variables rather than constants. In the study reported here, the analogy with turbulent flow has been used in treating unstable miscible displacement as a quasi-turbulent displacement process. The purpose has been to derive, even if restricted to an idealized conceptual model, a unified theoretical relationship applicable to both stable and unstable displacement. A relationship meeting these specifications up to moderately adverse viscosity ratios, such as 17:1, is presented. One fluctuation parameter in the theory and dispersion coefficients are obtained by empirical means. The idealized theory is compared with experimental results. UNSTABLE MISCIBLE DISPLACEMENT AS QUASI-TURBULENT DARCY FLOW The miscible displacement of one fluid by another within a porous medium is considered in this study. Flow conditions are such that Darcy's law is applicable. It is further assumed that, by the stability criterion proposed by perrine,1 initial flow conditions lie well within the regime of instability. Thus substantial viscous fingering is assured. We wish to show how this flow regime can be represented as quasi-turbulent. That is, the Reynolds number for the established flow conditions is below that for inertial or turbulent flow within a porous medium, and lies within the regime for which Darcy's law is valid. Yet flow behavior can be described as the combination of some relatively simple average result, and characteristic fluctuations that are superimposed on the simpler behavior. Stated another way, flow behavior includes the movement of layers of fluids with different velocities past or over one another. Such descriptions are characteristic of turbulent pipe flow. The fluctuations in the present case are a direct consequence of the local viscous fingering which accompanies the unstable displacement process. Should displacement become stable, fluctuations would die out. It is of particular importance to note that fluctuations such as these can interact in a way that contributes to material transport by the basic flow. The basic transport equations required for engineering calculations must be modified to reflect this fact.

By Milton C. Neul

As recently as the mid-1930's, steam and rail haulage were still the primary means of moving large quantities of rock. However, 2- to 5-ton standard on-highway trucks were beginning to be used in the mining industry's efforts to lower haulage costs. It was quickly obvious that rubber-tired equipment was more flexible, faster and more maneuverable. The trend towards haulage trucks had begun. Now while savings were being realized, the severe operating conditions encountered in open pit operations proved too much for the lightly constructed frames, gasoline engines and highly inflated tires. As a result, a few years later, the first 10 to 15-ton, two-axle heavy duty trucks were designed specifically to operate under off-highway conditions.

Jan 3, 1966