Search Documents

By H. I. Aaronson, C. Laird

Although the past results of X-ray experiments indicate that the broad faces of 0' plates are coherent with their matrix, dislocations lying in arrays have frequently been observed at these boundaries by transmission electron microscopy. Critical experiments employing the latter technique have been carried out in order to determine the origin of these dislocations. It is concluded that 8' plates are essentially coherent with the matrix at their broad faces throughout the aging temperature/time envelope studied. Virtually all of the dislocation arrays observed are deduced to have been formed by plastic deformation accompanying transformation. The proportion of dislocations arising from convexity of the plates is shown to be negligible by comparison with that from plastic deformation. At the higher aging temperatures, a[001] dislocations appeared in moderate numbers. These dislocations were traced directly, however, to the ledgewise dissolution of 0' occasioned by the formation nearby of 0 crystals. On the other hand, since there is a parametric difference normal to the broad faces of the ?' plates, mismatch dislocations do form at their edges. A previous conclusion that these dislocations have Burgers vectors of type a[001] was confirmed directly. The edges of 0' plates were observed to develop octagonal shapes when growing, but circular shapes during dissolution. 1 HIS paper presents the results of an investigation of the interfacial structures of plates of the transitional phase, 8', formed in an A1-4 pct Cu alloy. In a companion paper, Part 11, the effects of these structures upon the migration kinetics of a:?f boundaries are reported. This work is pa.rt of a general program designed to establish the basis of precipitate morphology. The present authors in Al-Ag,1 and whitton2 previously in U-C alloys, have used transmission electron microscopy to examine directly the vander Merwe3-6 networks of dislocations anticipated7 to compensate the small amount of lattice misfit normally founda at the broad faces of Widmanstatten plates. Since the broad faces of 0' plates are considered to be perfectly coherent with the corresponding habit planes in the a matrix,' no dislocations should be present at these faces. Many reports have been published, however, giving evidence to the contrary.10-18 The primary objective of this investigation was therefore to ascertain the nature of these dislocation structures. An attempt to do this is described in the first three sections of this paper. Inspection of the matching of the a and 8 ' lattices at the orientations of the 0:0' boundary corresponding to the edges of 0' plates raises the possibility that these edges may be made up of rather closely spaced edge- type misfit dislocations oriented so as to be sessile with respect to the lengthening or shortening of the plates. Since this structure should severely inhibit migration of the plate edges (Ref. 7, Part II), a situation not originally anticipated,' an experimental determination of the interfacial structure of the edges of 8' plates was clearly in order, and is reported in Section III. Those aspects of the experimental procedure applicable to both Parts I and I1 are presented in the next section. Specific procedures applicable to individual aspects of each investigation, and also the relevant surveys of the literature, are then individually reported in the appropriate sections. I) GENERAL EXPERIMENTAL PROCEDURE The material used in both parts of these studies was the same as that of a previous investigation:" strips of A1-3.93 pct Cu, 0.009 in. thick, prepared as before, solution-annealed at 548°C for 6 hr, and quenched. Details of subsequent aging, and in some cases deformation treatments, are given in the Experimental Procedure sections of the individual parts of both papers. Specimens of the heat-treated strips were electro-thinned as beforeLg and examined in a Philips EM 200 microscope equipped with a goniometer stage. A commercial hot stage, of the grid-heater type and capable of * 30-deg tilt about one axis in the plane of the specimen, was also used for kinetic studies. The usual precaution of calibrating for the additional heat supplied by the electron beam was taken.19 A 16-mm cine cam-I era mounted outside the viewing window was frequently used to record the transformations. Conventional selected-area diffraction and dark-field viewing techniques were used to identify the precipitates in the foils. Normal bright-field images corresponding to two-beam diffracting conditions or dark-field images were employed to characterize the dislocations observed at the interfaces of the precipitates. The application of these techniques to the study of an interphase boundary, and the interpretation of the images,20'21 has been fully described in a previous paper.'

Jan 1, 1969

By David B. Burrows, Rlkl Kobayashi, Norman L. Carr

The viscosity of hydrocarbon mixtures, whether in the gas or liquid phase, is a function of pressure, temperature, and phase composition. This paper presents methods for the prediction of the viscosity of the gas or less dense fluid phase over the practical range of pressure, temperature, and phase compositions encountered in surface and subsurface petroleum production operations. The correlation necessary to predict the effect of pressure on viscosities is presented in Part I. Serious discrepancies in high pressure gas viscosity data in the literature are discussed. The application of the correlation to predict absolute viscosities is discussed in Part 11. Auxiliary correlations are presented to enable calculations of viscosities from a knowledge of the pressure, temperature, and gravity of the gas phase. INTRODUCTION A knowledge of the viscosity of hydrocarbon fluids is needed to study the dynamical or flow behavior of these mixtures through pipes, porous media, or more generally wherever transport of momentum occurs in fluid motion. Since flow is predominantly in the laminar region in petroleum reservoirs, the influence of fluid viscosity on this flow is especially important. As early as 1894, Onnes1 and Onnes and de Haas' noted that the viscosities of homologs under corresponding states could be correlated. The theorem of corresponding states has been further developed and applied to the viscosity of pure, nonpolar gases under pressure by Comings, Mayland, and Egly.3 It was demonstrated that the viscosity ratio could be expressed rather closely as a function of reduced pressures and temperatures, 1.e.: µ/µ1 = f( TR2 PR) ........(1) temperature, absolute units where: TR =------------------------------ ------ critical temperature. absolute units _pressure, absolute units critical pressure, absolute units µ = viscosity of gas at reduced temperature TR and reduced pressure PR µ1 =. viscosity of gas at atmospheric pressure and at temperature TR Serious discrepancies in the viscosity of pure hydrocarbon gases at high pressures have been called to Our attention by Comings, and and Egly. They made a careful analysis of the following methods commonly used to measure gas viscosities: 1. Oscillating disc viscometer4,5 2. Rolling ball viscometer6,7 3. Capillary tube viscometer12 On the basis of their analysis of the problem and their experimental data on the viscosities of methane, ethylene, carbon dioxide, and propane, they preferentially selected data obtained by the capillary tube viscometer to develop their viscosity correlation. Since then a need has existed to verify the experimental technique of Comings, Mayland, and Egly for the determination of viscosities at high pressure; to extend the data to mixtures of hydrocarbons; and to extend the range of their correlation to include higher pressures. Using the correlation procedure of Comings, May-land, and Egly, the prediction of gas viscosities is resolved into the correlation of the effect of pressure, temperature, and composition on the viscosity of hydrocarbons and their mixtures and the prediction of viscosities of mixtures of hydrocarbons and other natural gas components at one atmosphere pressure.

Jan 1, 1955

By Frank E. Shepard

Electric power in mining-operations is now successfully applied to haulage, hoisting, lighting and pumping; and until lately, drilling was the one department of mining in which an electric source of energy had not been introduced. Drilling by electric power has been the field for much investigation and several forms of electric-drills have been tried; but in the severe service of rock-drilling many dieculties have been encountered, and the heavy cost of repairs has caused a deep prejudice against this system of drilling. In the majority of electric rock-drills previously placed on the market, two principal factors have been considered; first, a portable electric motor usually of heavy pattern, coupled to the driving-mechanism of the drill proper by means of a flexible shaft; and second, the coupling of some form of reciprocating cross-head to a piston by means of a spiral spring, the drill-bit being fastened to the piston-rod by some suitable form of chuck with fastening bolts and nuts. In this latter form of drill, the cross-head has a fixed stroke, while the piston with drill-bit attached is allowed a variable stroke through the

Jan 1, 1904

By D. H. Bacon

Nearly all men are too busy with their own affairs to keep informed of the progress in other lines. From time to time we read statistics showing the development in some industry that astonish us; but the feeling of surprise soon fades: to be followed by others that likewise pass away. A short resume of what has been done in one line may be of interest. Down to late in the fifties the ore-product of Lake Superior mas handled over a mule-tram-road to Marquette; now the Duluth, South Shore and Atlantic, the Chicago and Northwestern, the Wisconsin Central, the Duluth, Superior and Western, the Duluth, Mesabi and Northern, the Duluth and Iron Range and the Lake Superior and Ishpeming railroads serve the shippers. Down to nearly 1870 a 700-ton ship was an enormous craft, the loading of which required two days; the unloading being seldom accomplished in that time. In 1871 the largest ore-barge carried 1050 toils and made twelve trips per season. Now the cargoes reach 5000 tons, the loading requiring less than three hours, and the unloading ten hours. Now the mines cover more land than was familiar to even the " timber-cruiser " when the Jackson mine was opened. The annual shipments have grown from a few thousand to 10,000,000 tons, and the ability of the mines to produce is not taxed. Lake-freights are at one-eighth, and rail-freights at one-quarter, of early prices. The deeper waterways, commodious locks and large ships of to-day are in a greater measure due to the movement of ore than to any other cause. Great savings have been made in each detail of each department. The only item of cost that has not been lessened, I am glad to say, is the money paid to men. Wages, measured by what they will buy, are as high

Jan 1, 1898

By David Browne

THE literature dealing with the physical constants of nickel is so fragmentary and unrelated, that a synopsis presents unusual difficulties. It is only within the last few years that investigators have understood the importance of placing on record not only the determinations they have made but also the composition, physical treatment, and past history of the material investigated. For this reason much of the earlier literature is valueless. Determinations have been made of the same physical constants on samples differing widely in origin, composition, and treatment, and the results differ widely among themselves. In the first place nickel is almost as flexible a term as steel. Its physical properties are widely influenced by its composition and treatment. It absorbs large quantities of gases and is exceedingly difficult to prepare in a state of chemical purity comparable to gold, silver, or copper. It is vitally affected by thermal and mechanical treatment. Hence in the following pages the recorded literature, where quoted, must be accepted with a certain reserve and used, as far as possible, as a check on later observations, in which these important factors are noted. In every case where new determinations are given, an attempt has been made to record all available information concerning the composition and treatment of the material used so that the data may serve as steppingstones toward a wider knowledge of the properties of the metal. As this synopsis is an attempt by men of metallurgical training to do what should long before have been clone by physicists, it is to be expected

Jan 9, 1919

By M. L. Samuels

DURING the period from 1910 to 1920, there was a lively interest in the subject of grain growth and many papers were published, followed by interesting discussions. Questions dealing with the fundamentals of grain growth-why and how it occurs-were treated in papers by Howe,1 Jeffries,2 Sauveur,3 Chappell,4 Beilby,5 Mathewson and Phillips,6 McAdam,7 Carpenter and Elam,8 Stead and Carpenter,9 Ruder,10 as well as others. Since that decade, much indeed has been done regarding the practical control of grain size, and it is now possible to order material having a size specified in the American Society for Testing Materials classification. Also, one hears the term "spliced boundaries" used in connection with certain tungsten lamp filaments" wherein it is important to prevent "sagging" between consecutive turns of the helix." This practical use of a certain knowledge as to the things that influence or even control grain growth should not be taken as an indication that the subject has been thoroughly explored and that nothing more can be learned from fundamental studies. It is with this thought in mind that a report of some observations and experiments on abnormal grain growth is believed justified. Abnormal grain growth is met with in heat-treating high-carbon steels in the austenitic range,13 in the hardening treatments of high-speed steels, 14.11 and in the low-temperature annealing of strained low-carbon steels as in sheet and wire material. Entirely aside from these instances of exaggerated grain growth, which some might consider as freakish, it is thought that abnormal growth is simply a case where the growth forces and the forces tending to prevent growth are almost, but not quite, evenly balanced. Information relative to grain-growth characteristics in general may be obtained from a study of abnormal growth conditions, which may be looked upon as vantage points. Reflection will show at once that if growth forces are great in comparison to inertia or resistance to growth, many crystals start to grow and, for that reason, none becomes very large, whereas if inertia is predominant no growth at all takes place. Under conditions in which

Jan 1, 1938

NEW MEMBERS The following list comprises the names of those persons who became members during the period Feb. 10 to Mar. 10, 1915: Members BANKS, HAROLD PURDY, Min. Engr 61 Broadway, New York, N. Y. BARAGWANATH, JOHN G., Min. Engr., Morococha Mining Co.; Morococha, Peru. BEESON, JOSEPH JOSIAH, Min. Geol Stanford University, Cal. CALLOWAY, ALFRED W Pres., Davis Coal & Coke Co., Cumberland, Md. DEETRICK, JAMES W., Mgr., Republic Iron & Steel Co., 826 Pennsylvania Ave., Youngstown Ohio.

Jan 4, 1915

By C. S. Roberts

Four binary alloys in this system were creep tested at 300°' to 600°F. A photographic study of microstructural changes showed that the outstanding creep resistance results primarily from a potent precipitation hardening locally at grain boundaries. Twinning was correlated with the primary stage and nonbasal slip with the tertiary stage of creep. THE utility of the rare earth metals as ingredients of magnesium alloys destined for elevated temperature application has been recognized for about 15 years. A review of the early development of these alloys has been given by Leontis. 1,2 It has been only recently that a desire has arisen to understand basically their remarkable creep resistance. The present research had that object. The work of Leontis showed that the differences between the behavior of the individual magnesium-rare earth element binaries was of commercial significance. However, the variations were small compared to the overall difference in creep resistance between the group as a whole and the magnesium alloys of the Al-Zn type. It was decided to conduct this investigation with one binary system which would be representative of the magnesium-rare earth element alloy group. Cerium was chosen as the solute because of its near-middle position in the series and because of its availability in the commercially pure form. A previously published description of the creep behavior of electrolytic magnesium" serves as the background to this research. The experimental approach used in that investigation has been partially repeated here. A series of binary alloys was planned to include the following: 1—A dilute alloy which would contain the cerium almost entirely in solid solution. This would assess the solid solution effect. 2—An alloy which is nearly saturated at the selected solution heat treatment temperature, 1070°F. Here the effect of nearly maximum precip- itation would be obtained without the influence of undissolved Mg-Ce intermetallic. 3—An alloy containing slightly more cerium than is soluble at 1070°F. This would allow the investigation of the effect of a small amount of excess intermetallic. 4—A high cerium alloy in which the influence of a large volume of undissolved intermetallic may be examined. Experimental Details In order to specify compositions of the binary alloy series a knowledge of the solubility of commercially pure cerium in solid electrolytic magnesium and also of the composition of the terminal intermetallic phase was necessary. The latter has been proven to be approximately Mg,Ce by Voge14 and Haughton and Schofield.5 A series of both cast and extruded alloys were solution heat treated 24 hr at 1070°F for a solubility determination. Lineal analyses of the polished and etched microstructures were accomplished with the aid of a Hurlbut

Jan 1, 1955

By Brahm Prakash, R. Schuhmann

Chemical conditions for flotation and nonflotation of cassiterite and fluorite with oleic acid as collector and with alizarin dyes as modifying agents were studied by means of small-scale, vacuum-flotation tests. Artificial cassiterite was prepared for these tests by high-temperature methods, especially by crystallization from borax melts.

Jan 5, 1950

By W. C. Hittinger, J. McGlassan, J. W. Peterson

THIS paper describes the result of an investigation of the production of thin alloyed layers on a thicker substrate of pure germanium as one step in the manufacture of transistors.' The technique of alloying materials with semiconductors is a means of introducing small amounts of impurity elements in the alloyed regions of the crystal lattice of the semiconductor, the presence of which make possible the junction type transistor.2 Impurity elements are added which will produce regions having differing electrical resistivities and means of carrying current. Impurities are of two types: those which produce an excess of electrons (negative or n-type), and those which produce a deficiency of electrons (positive or p-type) in comparison to the pure semiconductor. The boundary between two such regions is designated a p-n junction. Elements in Group V of the periodic table, having five valence electrons, give rise to an excess of electrons when present substitutionally in the semiconductor lattice (usually germanium or silicon from Group IV). Similarly, elements in Group III create a deficiency of electrons. Germanium and silicon which are substantially free of impurities of either p or n-type are designated intrinsic (i-type) semiconductors. The usual junction ----trarnsistor has

Jan 1, 1958

By Charles C. Upham

Not long ago a few acres of coal-land in the Connellsville region of Pennsylvania were sold at the rate of $1500 per acre. While this was doubtless a " fancy " price, affected by some consideration other than that of the simple value of the coal in the tract. it may fairly be taken as an indication of a progressive and already perceptible diminution in the economically available coal-resources of that famous region. This piesent and prospective development emphasizes the cominercial importance of producing, from the inferior coals of other districts, coke suitable for use in the blast-furnace. Many of the bituminous coals of the United States would meet this requirement if sufficiently freed, before coking, from slate and sulphur, and, so far as the removal of slate is concerned, the problem is not specially difficult. There are many forms of trough-, jig- and gravity-washers which easily and cheaply reduce the slate from as much as 20 per cent. in the coal to as little as 8 per cent. in the coke. But to reduce the sulphur from 4 per cent. in the coal (a proportion sometimes encountered) to 1 per cent. or less in the coke (the proportion demanded by the furnace-manager) is not so easy. It may be safely assumed as familiarly known to members of the Institute interested in this subject that, of the three forms in which sulphur usually exists in coal (hydrogen sulphide, calcium sulphate and pyrite), the pyrite is the one to be removed, RS far as possible, by mechanical treatment before coking. Hydrogen sulphide, being volatile, is expelled in

Jan 1, 1899

By A. F. Taggart, A. M. Gaudin

Flotation of ores is a practical utilization of the energy that resides in the surfaces of solids and liquids. The best known manifestation of this energy is called surface tension; an equally important, though less apparent, phenomenon is adsorption. This paper reviews some of the recent investigations of these phenomena, and gives the results of certain experiments performed by the authors. Surface tension is a manifestation of energy having its seat at the bounding surface between the adjacent phases of a multiphase system. Thus, at the interface between a liquid and a gas, or between two immiscible liquids, or between a solid and a gas or a liquid, there are forces capable of doing work, their magnitude depending on the nature of the adjacent phases and the extent of the bounding area. These surface forces are inappreciable when the ratio of surface to volume of the adjacent phases is small, but they become powerful when this ratio becomes large, as it does when one of the phases is highly dispersed. Froth flotation, which consists in buoying solids heavier than water to the surface of water by means of gas bubbles, utilizes the force of surface tension to attach the solid particles to the gas bubbles and again to maintain the floating mass of bubbles as a more or less persistent froth at the surface of a pulp for a sufficiently long time to allow its removal. It follows from the second law of thermodynamics that the potential energy of a system in equilibrium is a minimum. Therefore a multiphase system, tending toward equilibrium, will arrange itself in such a way that the total energy of the interfaces will be the least possible. This end can be accomplished in two ways: by a change in shape that will reduce the interfacial area; by a change in the nature of the surface layer in

Jan 1, 1923

By Hollis L. Caswell

The present status of integrated circuits utilizing. superconductive switching. elements is reviewed with special attention given to fabrication techniques, methods for interconnecting completed circuits, and refrigeration requirements. Cryoelectronics has been largely an "inte- grated-circuit" technology since its conception because the switching speed of superconductive devices is attractive only when these devices are fabricated with thin-film techniques. It is true that cryotron circuits can be constructed from wires of appropriate materials (as indeed was done by Dudley Buck 1 in his early investigations) but these circuits will switch in times characteristic of milliseconds whereas similar circuits fabricated by thin-film methods have potential switching times of nanoseconds. Furthermore, cryo-electronic devices such as the cryotron lend themselves readily to fabrication by thin-film techniques since these components may be made from polycrys-talline thin films and are relatively insensitive to the presence of impurities (as measured by semiconductor standards). Therefore, during the past decade considerable effort has been devoted to developing techniques for batch fabricating circuit arrays containing superconductive switching elements. Technology had developed to the point several years ago that fabrication of cryoelectronic arrays containing up to one hundred devices was rather straightforward. However, larger arrays containing between lo4 and 106 components which are required for commercial development of cryoelectronics still pose very severe yield problems. Thus in a sense cryoelectronics found itself in 1962 at the point semiconductor technology finds itself today; namely, individual devices and small groups of integrated devices could be fabricated with acceptable yield and the outlook for building larger integrated-circuit arrays was bright. Unfortunately, problems associated largely with yield have made fabrication of these larger arrays difficult. Unlike semiconductor technology, cryoelectronics had to solve the problems of large-scale integration before it could become economically attractive. This has proven to be a sizable burden to bear. Since several reviews exist on superconductivity,2 superconductive devices,3 and cryoelectronic technology, no attempt will be made in this paper to summarize these areas. Instead a few specific topics will be dealt with in more detail. First, a brief description is given of selected superconducting switching and storage devices with special attention to several metallurgical techniques which improve the performance of these devices. Second, techniques used to fabricate cryoelectronic devices are described with emphasis on problems affecting yield. Third, techniques for interconnecting a number of cryoelectronic planes are described. And last, refrigeration of cryoelectronic components is discussed briefly since the low operating temperature of superconductive devices is an important consideration in this technology. SUPERCONDUCTING STORAGE AND SWITCHING DEVICES The basic superconductive switching device is the thin-film cryotron. The geometry of this device is attractively simple, since it involves only the intersection of two lines that are electrically insulated from each other. The switching element (gate) and control element (control) of a crossed-film cryotron are arranged as illustrated in Fig. 1. The material for the gate is selected to permit the gate to be switched from the superconducting to the normal (resistive) state by the application of a control current. Tin, which has a critical temperature (T,) of 3.7°K, is commonly used for the gate and the cryotron is operated at a temperature just below T, (for example, 3.5°K). The control material (normally lead, with T, = 7.2°K) is chosen so that the control is never driven normal during circuit operation. To improve cryotron operation, a ground plane, also of lead, is placed under all of the circuitry to act as a diamagnetic shield and improve the current-density uniformity across the width of various thin-film elements. Normally, line widths vary from 0.005 to ^ 0.020 in. and film thicknesses from 300 to 10,000A, although new fabrication techniques make narrower lines feasible. In fabricating cryotrons it is important that the edges of the gate elements be geometrically sharp to avoid undesirable switching characteristics associated with a thinner edge region, Fig. 2. One technique which has been used extensively to form patterns consists of placing a physical mask containing the film pattern between the evaporation source and the substrate and depositing through the mask. Film strips formed in this manner possess a penumbra at the film edges due to shadowing of the evapor-ant under the mask. Several techniques have been proposed for minimizing effects due to this penumbra. One of the more promising metallurgical techniques

Jan 1, 1967

By Suzanne T. Mathis, J. C. Ferm, J. T. Berger, W. Horger

A system of core logging and computerized entry and retrieval is described which permits accurate and rapid logging of core, cuttings and geophysical records derived from exploration and development bore holes. The system is so constructed that older drilling records can also be utilized. Output consists of conventional computer print out and graphic logs with a variety of scales, symbols and formats. Such logs can be used in constructing rock profiles which are necessary in property assessment and mine development.

Jan 1, 1983

By J. F. Abel

It can be concluded that rock mechanics instrumentation, geologic mapping, and operations research in combination will produce an accurate estimate of tunnel support requirements for establishing a steel-set load prediction model. This estimate can be used to increase safety and to reduce tunneling costs. Unnecessary supports can be eliminated; overloaded or insufficient supports can be replaced on a more scientific basis than previously possible. Only a limited number of measurements are required to develop a steel set load prediction model. The results of this study can be applied generally; but, every tunnel must be considered as a separate problem. The construction and geologic variables which were found to be significant in the prediction of rock loads in this tunnel were: steel section modulus, set blocking points, percentage of alteration, relative degree of faulting, relative water condition, distance to the nearest fault, and average joint spacing. INTRODUCTION A combined engineering geology and rock mechanics program was performed throughout the Straight Creek tunnel pilot bore in Colorado in order to develop a technique for estimation of steel tunnel support loads. The technique involves the construction of a statistical model from measured steel set loads, geologic and construction factors. The aim of the investigation was to produce a set of charts, based on these factors, which could be used by a trained man equipped with a hand lens and measuring tape, to specify a safe and economical steel size and set spacing. In order to be of practical value the measured parameters had to be rapidly measurable and capable of quantification. It was apparent from the beginning that quantitative values for many of the geologic factors would have to be arbitrary. It was impossible to ascertain in advance which of the readily determi-nable geologic and construction factors significantly affect steel set loading. As the investigation progressed the number of observations was systematically reduced in order to determine the minimum amount of data which would be necessary for a significant mathematical model. This paper presents an analysis of all the variables measured at each instrumented steel set. The statistical significance of the measured variables was determined. On the basis of this determination, a mathematical model was constructed and charts were prepared to select and space the steel tunnel supports at any given point in the tunnel. Once the effect of geologic and construction factors on set loading is sufficiently established, it is possible to exert close control over the selection of steel tunnel support size and spacing. The magnitude of this rock mechanics program can be appreciated when it is known that there were 44 instrumentation stations for which steel set loads were measured. For each of these sets there were three construction variables recorded, and nine geologic parameters determined (Table I). A rough approximation of the cost for both the collection and reduction of the data would be $50,000. This is in addition to the cost of geologic mapping.

Jan 1, 1967

By C. H. Li, R. J. Stokes, T. L. Johnson

The effect of alumina particles on the nucleation and growth of cracks through a silver- chloride matrzx has been investigated. It has been found possible to promote fibrous cracking in dispersion-strengthened silver, chloride under notch-impact conditions at temperatures at which silver chloride alone cleaves brittlely The modification) of fracture beIzavzor is thought to be due to the relaxation of hydrostatrc stress beneath a notch by the nucleation of cavities near alumina particles. In recent years, composite or dispersion-strengthened materials have been studied primarily to understand their high resistance to plastic flow particularly at elevated temperatures. Dislocation models have been developed with which it is possible to deduce with fair success the effects of interparticle distance, particle size, temperature, upon yielding and creep behavior.l-4 Much less attention has been paid to the fracture behavior of these materials (with the notable exception of common structural steels) and little is known experimentally about the manner in which inclusions affect the nucleation and growth of cracks through a matrix. Nevertheless a beginning has been made in connection with fibrous cracking in ductile matrices where inclusions appear to play an essential ro1e.5-7 During the severe localized plastic deformation which accompanies necking in a tensile test, cavities are believed to develop at inclusions; these cavities subsequently grow and coalesce by plastic flow until separation is complete. It is of interest to consider whether inclusions can affect fracture behavior under loading conditions which restrict the plasticity of the matrix itself (for example, cleavage under conditions of a high imposed strain rate at low temperatures). It is particularly interesting to study these effects in a solid which shows a spectrum of behavior ranging from fully ductile to semi-brittle behavior. Such a solid is silver chloride whose mechanical behavior depends sensitively upon temperature and strain rate.'," The present paper is concerned with a study of the influence of inclusions (in the form of alumina particles) on the fracture behavior of silver chloride loaded uniaxially at low strain rates at room temper- ature and also under notch impact conditions over a wide range of temperature. In particular, it will be shown that the alumina particles can exert a startling effect on the ductile-brittle transition temperature of notched silver chloride and that the magnitude and nature of the effect depends upon both the quantity of alumina and the shape of the alumina particles. 1. EXPERIMENTAL PROCEDURE 1.1 Materials Used. Silver chloride powder of analytical reagent (AR) quality having an average particle size 6 was supplied by the Mallinckrodt Chemical Works (st. Louis, MO.). Acid washed 900 mesh alumina powder, designated A38-900, was supplied by the Norton Co. (Cambridge, Mass.). This powder was added to silver chloride in two forms: a) the as-received condition in which the individual particles were of random irregular shape; their statistical average size was 7; b) in a condition in which each particle was spherically shaped by a fusion technique. In this case, the statistical average particle size determined with the optical microscope was approximately the same (about 5p) but electron micrographic evidence indicated that many ultra fine particles were present in the spheroidized powder. 1.2 Preparation of Composite Materials. Silver chloride-alumina composites containing 2.5, 5, and 15 pct by volume of alumina were produced by the extrusion of mechanically mixed powders blended in a ball mill for 24 hr at room temperature. The mixtures were compacted at 50,000 psi at room temperature in the form of billets 3/4 in. in diameter and 1 in. long which were then extruded with a 16:l reduction ratio at 370°C through a radius-type steel die having a 5 deg lead-in angle. An extrusion temperature of 370°C was selected to ensure that all composites had sufficient plasticity to be extruded. Apart from this general requirement, the choice was arbitrary. 1.3 Microstructure of Composites. Attempts were made to check the distribution of alumina metallo-graphically by polishing transverse and longitudinal sections of the extruded rod. Specimens were wet-ground to 600 emery paper and lapped successively with 5 and 0.25-p grades of diamond paste. They were etched for 10 sec in 10 pct sodium thiosulfate solution and lightly polished in concentrated ammonium hydroxide. The most effective way to render the alumina particles and grain boundaries visible was to radiate the surface with intense white light to decorate the grain boundaries and the particle-matrix interfaces photolytically.

Jan 1, 1962

By Ben B. Sweet

The ongoing controversy over mining and agricultural use of ground water in Arizona underscores the importance of this commodity to both industries. Although the principles presented in this article are fundamental, a method of systematic data collection and interpretation is provided for evaluating a water well by a set of uniform standards common to all areas where ground water is a primary source of supply.

Jan 8, 1978

By Frank S. Shuri

INTRODUCTION The Calumet Pumping Station, located on the south side of the Greater Chicago area, is part of the Tunnel and Reservoir Plan to accomodate the city's wastewater. The Station consists of two parallel rock caverns, each 18 m high, 20 m wide, and 62 m long, located in Silurian dolomite approximately 91 m below the ground surface. The caverns are oriented N-S with a 24-m-wide pillar between them. Prior to construction, rock mechanics studies were conducted in an L-shaped test adit at the location of the west cavern. The purpo3e of the rock mechanic studies was to characterize the site, particularly the in situ stress field and deformation characteristics of the rock. This information, together with other physical properties of the rock and geologic data, was used to evaluate the stability of the preliminary cavern design, with particular emphasis on cavern orientation, rock reinforcement, and pillar stability. GEOLOGY OF THE SITE Stratigraphy The Chicago area is located on the Kankakee Arch, a broad, gently sloping arch of Paleozoic sediments. Rocks in the project area consist of Silurian dolomites unconformably overlain by Pleistocene glacial deposits. The formations of interest to this study are: - Racine Formation, inter-reef facies. This dolomite is gray- brown, silty, and compact. It contains occasional prominent bedding surfaces. The Racine Formation in the project area varies from 73 to 74 m in thickness.

Jan 1, 1984

By C. P. McCormack

The Cuyuna manganiferous iron ores can be a principal source of manganese for the iron and steel industry in the United States, provided metallurgical methods as a whole are adjusted so as to use run-of-mine ore. The use of manganese in steelmaking is growing. Increasing amounts of impurities in raw materials call for more manganese, a constant cheap supply of which is wanted. There are few deposits of ore in the United States carrying over 35 per cent. manganese that can be mined and marketed at a profit in normal times. We are largely dependent on foreign ores. The small domestic deposits should rightly be held in reserve for an emergency, such as a war, when importation might cease. Even the production from lean ores, concentrated it may be, might not carry us through a protracted stringency. The Cuyuna district is, therefore, during normal times capable of supplying a large total of manganese. The ores are iron ores containing 5 to 25 per cent. of manganese with the inverse range of 52 to 28 per cent, of iron. The manganese costs no more per unit in the ore than the iron, because cost of mining, largely by open-pit methods, is not affected by the manganese content. The manganese units should, perhaps, command a higher price, but as their value is contingent on metallurgical practice, a higher price may be justified only when a shortage in manganese occurs. Manganiferous iron ores can never entirely supplant straight manganese ores though methods are employed that will permit them to do so partly. For the manufacture of ferromanganese, ores carrying above 42 per cent. manganese are needed. Ores with manganese running between 20 and 42 per cent. are used for making spiegeleisen. But established practice in certain plants, based on the admixture of manganiferous iron ores to straight iron ores has greatly lessened the consumption of high-priced, scarce, manganese alloys with good results. The substitution of manganiferous ores for ferro and spiegel affects the manufacture of basic iron and its conversion into basic open-hearth

Jan 1, 1925

By D. P. Koistinen, K. E. Beu

THE application of the integrated intensity X-ray diffraction method to the measurement of retained austenite concentrations in hardened steels has been fully described.'-' In developing this particular method, the assumption was made that the samples used would have flat surfaces which were free from voids and in which austenite was homogeneously distributed. The original calculation procedure' was modified to include the constant factor G which relates the intensity of a given diffraction line to the concentration of the component giving rise to that line. In order to include A (0) in the constant factor G, it was further assumed that the geometrical conditions relating the X-ray beam, camera cylinder, and sample surface were precisely met.V has been demonstrated that these geometrical conditions can be met experimentally without difficulty in many cases;' however, for those samples which have irregular surfaces or where it is impossible to locate the sample in the proper position with respect to the X-ray beam and film cylinder, it is desirable to evaluate experimentally what effect these nonideal conditions have on the reliability of the austenite determination. This note decribes the results of such experiments. SAE 1095 bar stock was used throughout and all samples were heat-treated as follows: 1600°F for 1 hr in a neutral atmosphere, brine quench, and 300°F temper for 30 min. To control heat-treatment conditions as closely as possible, all samples were plated with 0.002 in. copper to protect the immediate surface from the heat-treating atmosphere. After heat treating, the samples were deplated electroly-tically so that only the copper was removed. The heat-treated surfaces thus obtained were nearly as bright and polished as the original surfaces before copper plating although no mechanical work was done on the samples after heat treating.

Jan 1, 1954