Search Documents

Jan 1, 1936

By L. C. Kern

This paper presents information on the use of a new propping agent (malleable aluminum particles) which has been used successfully for producing high-conductivity fractures. The conductivity of a packed fracture depends on the width of the fracture as well as the permeability of the propping material. It is significant that the flow capacity of a propped crack is often increased many fold by propping the crack with a sparse distribution of particles. However, the flow capacity of a sparsely propped crack can be limited by two phenomena: (I) crushing of the propping particles, and (2) embedment of the propping particles in the formation walls. Malleable aluminum particles exhibit interesting properties which tend to overcome these limitations. As high loads are applied to the particles they will deform slightly, rather than shattering. The deformation results in a greater bearing area against the formation wall. This reduces the stress on the particle and reduces particle penetration into the formation. The behavior of aluminum particles under load and the bearing capacities of serveral formation rocks have been measured in the laboratory. By properly using these data, as explained in this paper, the flow capacities of aluminum-propped cracks can be calculated for a variety of conditions. Aluminum particles have been used successfully in the field to prop fractures. Where high-conductivity fractures were needed, the aluminum-propped fractures have given greater well stimulation than could have been expected for conventional fracturing processes. INTRODUCTION The purpose of a hydraulic fracture treatment is to create a conductive channel from the wellbore out into the oil or gas formation. The word conductive is emphasized because we believe that the fracture conductivity (flow capacity) is one of the most important factors influencing fracturing results. Previous papers have pointed out the additional well stimulation that can sometimes be achieved by increasing fracture conductivity. Several years ago, we investigated in some detail the effect of fracture conductivity on productivity increases to be expeced from vertical fractures. Both electrical analog and theoretical studies of unsteady-state flow behavior were made. A discussion of the electrical analog equipment and some of the results of the study were given in a previous paper' by Dyes, Kemp and Caudle. Further details were given recently by McGuire and Sikora.5 Fig. 1 shows the remarkable influence of relative fracture flow capacity and length on well stimulation. Briefly, the study indicates the following. 1. High-permeability formations require high-conductivity cracks for best results. 2. The longer the crack, the higher the fracture conductivity required for best results. 3. If the conductivity of the crack is very large compared to the formation (i.e., flow is not being limited by crack conductivity), then the longer the fracture, the better will be the results. Judging from recently published articles,1,314 there is current interest in methods for obtaining high fracture conductivities. Hence, we would like to present in this paper a discussion of a new fracture propping process (use of aluminum particle) which we have used successfully to obtain highly conductive fractures. There are several factors which influence the conductivity of a propped crack. Conventional fracturing techniques frequently result in a crack completely packed with fracturing sand. For such conditions, the crack conductivity is the product of the width of the packed fracture and the permeability of the propping material. It is significant that a large increase in conductivity sometimes can be obtained by propping with particles which are distributed sparsely (less than a

AARONS, J. BOYD, Major. AGNEW, FRANK VANS. ALLEN, HERMAN H., Private, D Co., 8th Reserve Engineers. BANKS, H. R., Lieutenant, Canadian Engineers, B. E. F. BARBOUR, PERCY E., Deputy Supt. (Captain), New York State Troopers; Captain, 22d Regiment, N. Y. N. G. BARLING, H. B., 1st Lieutenant, Engineer Officers' Reserve Corps. BIGELOW, BRAXTON. BLOOMFIELD, E. C., Lieutenant. BORROW, F. K. BROOKS, ALFRED H., Captain, Engineer Officers' Reserve Corps. BROWNE, DE Courser, 1st Lieutenant, Ordnance Dept., Fortress Monroe, Va.

Jan 8, 1917

By D. S. Bloom

RECENTLY a report has been published on an investigation of the MO-RU system by E. Raub.' In this report it is stated that below approximately 1200°C the system consists of two terminal solid-solution phases and the intervening two-phase field; at 1200°C and above, an intermetallic compound labeled Mo,Ru, makes an appearance. Along with some other little known systems in which it was considered possible for a u phase to form, the Mo-Ru system had been under investigation in this laboratory. Since molybdenum and ruthenium have very high melting points and also since ruthenium is expensive, the investigation was confined to X-ray diffraction by sintered powder compacts. The compositions which were studied were (in atomic percentages): 75 Mo-25 Ru, 67 Mo-33 Ru, 50 Mo-50 Ru, and 25 Mo-75 Ru. All compacts were made from the pure powders, and no chemical analyses were attempted. Each compact weighed about 5 g. All annealing was done in evacuated Vycor capsules, and even though the capsules completely collapsed at 1250°C, they still admitted no air. The results of this investigation in general corroborate the work of Raub. Up to 1150°C the two terminal solutions and the intervening two-phase field were found, and at 1200°C and above an intermetallic compound was found. However, the composition limits of the compound were estimated to lie close to 70 atomic pct Mo rather than 62.5 atomic pct Mo as Raub had reported. At least the X-ray diffraction results indicated that the 75 atomic pct Mo specimen consisted of the molybdenum solid solution plus the compound, while the 67 atomic pct Mo specimen consisted of the ruthenium solid solution plus the compound and the equiatomic composition contained only very little of the compound. The most interesting observation, however, was that the diffraction pattern of the compound was similar to that of the well known u phases, except that unusually large lattice constants were indicated. The d-values, or interplanar spacings, of the diffraction lines (as produced by filtered copper KCX radiation) of the compound are given in Table I, as determined from specimens annealed at 1250°C for 9 hr and then quenched in water. Also shown are the lines of the Mn-Mo u phase as given by Decker, Waterstrat, and Kasper,' the lines of the Fe-Mo a as given by Goldschmidt," and the lines of the Mo-Ru phase multiplied by constants in order to make comparison with the Mn-Mo and Fe-Mo patterns easier. These results indicate that the compound in the Mo-Ru system is apparently isomorphous with the other o- compounds. The rather large lattice constants of the Mo-Ru a phase are acceptable in view of the comparatively large size of the constituent atoms. The data in Table I for the Mo-Ru compound check quite well with those given by Raub, not shown here, though there are some discrepancies between the two sets of data in the estimated intensities of a few lines. Although very little is known at present about this u phase, there are some things which may be pointed out, mainly in comparison with other better known u phases. Even though molybdenum and ruthenium are in the same columns in the Table of Elements as chromium and iron, respectively, the Mo-Ru u phase contains much more molybdenum than ruthenium, while the Cr-Fe u phase centers around or very nearly around the equiatomic composition; furthermore, the Mo-Ru u is stable only above approximately 1200°C, but the Cr-Fe u is stable only below about 825 °C. With respect to its being unstable below 1200°C, the Mo-Ru u is similar to the other binary molybdenum u phases in the Co-Mo and Fe-Mo systems. Similar to the latter two systems, the Mo-Ru u apparently exists over a rather narrow composition range, whereas the Cr-Fe u at lower temperatures is stable over a much wider composition range. The Mo-Ru u thus is closer to the other molybdenum u phases than to the Cr-Fe cr phase. The most striking feature of the Mo-Ru u phase, however, is the absence of any of the transition elements of the First Long Period.

Jan 1, 1956

GEOLOGY is of service to man in two general ways according to Heinrich Ries in The Scientific Month-ly. The first of these is in exploring and evaluating the mineral resources on which industry and civiliza-tion are built, and the second is the application of geo-logic principles to various lines of human activity, such as engineering, agriculture, chemistry, etc. Both of these are phases of economic or applied geology, but neither could be developed before geology as a pure science was more or less firmly established, and in this process it freely acknowledges its indebted-ness to some of its older sister sciences such as chem-istry, physics, botany and zoology. Chemistry and geology are mutually helpful. Various chemical industries consume large quantities of raw mineral products, but since these vary in their purity and composition, it is important for the chemist to be familiar with the irregularities of composition which the different types may show, because he is often called upon to pass judgment on new sources of supply. Here geology helps the chemist. On the other hand, the laws of physical chemistry which the chemist has worked. out are of great assistance to the geologist in explaining many geologic processes.

Jan 7, 1927

By Howard R. Pratt, Jimmie L. Bratton

The Air Force Weapons Laboratory (AFWL) has been carrying out a series of experiments whose principal purpose is to measure the dynamic response of rock media to large pressure pulses. Coupled with the field experiments have been theoretical calculations simulating this response. These two approaches allow an appraisal of the current ability to measure in-situ rock response under extreme conditions and also give a fair estimate of the current state-of-the-art in the area of computer calculation of the response of "real" geologic media to a large load. The area chosen for the test series is composed of a sequence of sedimentary units (shale, sandstone, and limestone) located in the Estancia Valley 45 miles east of Albuquerque, N.M. (Fig. 1). The units, which dip gently off the uplifted Manzano Mountains to the west, are essentially horizontal at the test site. An extensive geologic and geophysical investigation of the area was carried out in the form of surface mapping and seismic exploration. Numerous holes were cored and material properties were determined from tests of the cores. In-situ geophysical measure¬ments were also carried out. The experiment consisted of loading a 60X40 ft test area with a 4000-psi transient exponentially decaying pressure pulse. The pulse was initiated at one end and traveled the 60-ft length of the test bed. The test area was instrumented with acceleration, velocity, and strain measuring devices placed in drill holes to depths of 30 ft. Theoretical computer calculations of the response of the layered geologic media have been carried out on the AFWL CDC 6600 using one and

Jan 1, 1972

By Oliver B. Hopkins

During the year 1936, a new high record was established for Peruvian production, the total amounting to 17,594,689 bbl., which brought the cumulative production of the country up to 205 million barrels. The 1936 figure represents an increase of 530,288 bbl. over that of 1935. The property of the International Petroleum Co. contributed 369,577 bbl. of this increase and the Lobitos property 158,233. Exploration work in the country was continued. The Selden Breck Co. examined a strip of the National Reserve in eastern Peru from Tambo del Sur to the Rio Pachitea. This company was granted a concession for a term of four years embracing approximately 50,000 acres near the confluence of the Rio Pachitea and the Rio Ucayali. During the year, the Peruvian Government commenced drilling a well on one of the reserved zones at Zorritos. At the end of the year, this well had reached a depth of 1300 feet. La Rrea-Parinas Estate.—Production on the La Brea-Parinas Estate of the International Petroleum Company, Ltd., reached an all-time high in 1936 of 15,126,491 bbl., an increase of 369,577 bbl. over the 1935 record. The total production from 1890 to 1936 was 163,668,014 barrels.

Jan 1, 1937

By R. A. Wood, R. I. Jaffee, H. R. Ogden, D. N. Williams

The tensile properties, creep resistance. and thermal stability of highly alloyed Ti-Al-Zr alloys were examined. On the basis of these studies, the Ti-7Al-1ZZr composition was selected for more complete evaluation. The alloy was found to be weldable and free from excessive directionality. In addition, it developed maximum properties without requiring heat treatment other than an annealing operation in the alpha field. The alloy was recommended for scale up and is presently being investigated on a production-level basis. One of the more attractive properties of titanium alloys is their ability to withstand stress at moderately high temperatures, and a considerable amount of effort has been devoted to increasing the maximum service temperature of titanium alloys. This work has suggested that the optimum alloys for high-temperature service will be single-phase a (close-packed hexagonal) alloys containing significant amounts of aluminum. However, the maximum amount of aluminum which can be alloyed with titanium is between 6 and 8 pct,l since at high-aluminum contents an embrittlement reaction occurs in the anticipated service temperature range, 800" to 1100°F. It has been shown that the embrittlement reaction involves decomposition of the high-aluminum a phase to one or more new phases.' Since this reaction does not occur at intermediate or low-aluminum contents, it was felt that intermediate Ti-A1 alloys might be strengthened by a-soluble ternary additions without inducing the embrittlement reaction. The first alloying addition considered was tin, which shows extensive solubility in a titanium and has moderate strengthening tendencies. Unfortunately, it was soon apparent that tin also promoted the embrittlement reaction, and that to obtain a stable alloy, the aluminum content had to be reduced as the tin content was increased. The second alloying addition considered was zirconium, which is similar to tin in its effects on titanium. This element did not contribute to the embrittlement reaction and, in fact, appeared to increase the maximum amount of aluminum which could be alloyed with titanium without inducing instability. This paper describes an investigation of the Ti-A1-Zr a alloy region. Alloys containing from 4 to 12 pct A1 and from 6 to 15 pct Zr were examined. The properties of these alloys are described and the bases for selecting an optimum composition is outlined. This composition, Ti-7A1-12Zr, is presently being scaled up in tonnage quantities, and is being evaluated extensively throughout the industry. In addition to presenting the basis for its selection, this paper presents a description of the properties developed in laboratory material as determined during the alloy investigation. These properties suggest that this alloy can fill an important position in applications requiring light weight, fabrica-bility, weldability, and strength to 1000oF or higher. EXPERIMENTAL PROCEDURES Titanium alloy ingots were prepared by inert electrode arc melting under an argon atmosphere. Alloying elements used were 110 Bhn titanium sponge, high-purity aluminum, and reactor-grade zirconium. Pancake-shaped ingots were prepared weighing approximately 300 g. The composition of the ingots was checked by weight measurements before and after melting. The pancake ingots were forged at 2000°F to approximately half their original thickness to give a flat plate roughly 1/2 in. thick. This plate was then rolled at 1800' to 1600°F to 0.250 in. thick. All of the alloys examined fabricated well. However, alloys containing 15 pct Zr tended to overheat due to exothermic oxidation, and scaling was excessive. As might be anticipated from its effect in decreasing the ß transus, increased zirconium appeared to improve fabricability somewhat, especially during rolling at lower temperatures. Except for a limited study of heat-treatment response, all alloys were examined in the a-annealed condition. Prior to heat treatment the a and ß tran-sus temperatures were determined by metallo-graphic examination of samples quenched after annealing at 50-deg intervals in the transformation region. These data are shown in Fig. 1. Recrystal-lization appeared to occur in about 1 hr in the range 1300º to 1500ºF. Therefore, alloys were annealed for 1 hr at 1550ºF (4 and 5 pct Al), 1600ºF (6 through 7-1/2 pct Al), or 1650°F (8 or more pct Al). This produced an equiaxed a grain structure. In most alloys, a "ghost" structure was visible after the a-annealing treatment, as shown in Fig. 2. This structure apparently resulted from the acicular

Jan 1, 1963

By Kent W. Pilz

Wet dust suppression can be achieved by 1) confinement of the dust within the dust producing area with a curtain of moisture, 2) wetting of the dust by direct contact between the particles and droplets of moisture or 3) the formation of agglomerates too heavy to remain airborne, or too heavy to become airborne, by combining small dust particles with each other and with the droplets of liquid. From the standpoint of economy, availability and safety, water is the ideal fluid; however, it is not as effective for dust suppression as when small percentages of specially formulated dust control compounds are blended with it. Performance of dust control com pounds is related to surface active agents and surface activity. In all liquids there is an attractive force between molecules which varies inversely as the sixth power of the distance between molecules. Thus, in the liquid phase where molecules are crowded together, the intermolecular forces are powerful; whereas in the liquid-vapor phase where the molecules are relatively far apart, these forces diminish rapidly. In the body of a fluid there is an uneven distribution of forces resulting in an inward pull called surface tension. The force which keeps two surfaces apart or causes them to coalesce is termed interfacial tension. Fluids of high surface tension exhibit poor wetting, spreading and penetrating qualities. Water has the unusually high surface tension of 72.75 dynes per cm at 20°C.

Jan 7, 1972

By Persifor Frazer

CONTENTS. PAGE 1. Committee House of Commons Report (1843).......521 2. Clark (1880).............521 3. Schröder and Schertel (1884).... . 521 4. Committee House of Lords Report (1887).......523 5. Vita (1890).............524 6. Irvine (1890-1)............524 i. Cramer (1891)............525 8. Bailey. Cohen. Tatham and Hartog (1891))......525 9. Morrison (1891)............525 10. Brunner (1891)............525 11. Bell (1892).............585 12. Oades (1892).............526 12a. Purcell (1892)............526 13. Sennett (1892)............526 14. Bulier (1892).............526 1.7. Wiesner (1892))...........526 16. Thomson (1892)............530 17. Fletcher (1892)............530 18. Committee Engineers' Club Report (1892).......530 19. Cohen and Hefford (1892)..........531 20. Discussion Soc. Chem. Ind. (1893). ..532 21. Reuss (1893).............532 22. Thomson (1894—5) ...........535 23. Clowes and Feilmann (1895). ...536 24. Callan (1895)...........536 2.5. Wright (1895)............536 25A. Mabery (1895)............536 26. Re- (1896). ..........536 27. Herman (1896)............ 537 28. Cohen and Russell (1896).......... 537 29. Dennstedt and A hrens (1896). ..537 30. Cohen (1897). ...........537 31. Drehschmidt (1897)........... 538 32. Pfeiffer (1898). .........538 33. Fritzche (1898)............ 540 34. Ost and Wehmer (1899)........... 540 35. Donkin (1899). .........541 36. Beilby (1899)............. 643 37. Berthelot (1900)............ 544

Jan 1, 1908

By A. Boltax

Precipitation processes occurring during both furnace cooling and aging of copper-iron albys were studied by means of electrical and magnetic measurements. On furnace cooling, two distinct stages in the precipitation process were detected; one occurring above and the other below 850° C. The kinetics of precipitation from quenched alloys were studied between 200° and 700°C. The reaction appears to be consistent with the concept of tmcleation of precipitate particles at dislocation loops formed by the clustering of quenched-in vacancies. A study Of in copper-iron alloys is particularly interesting because the combination of magnetic and electrical properties in these allovs provides a quantitative means of following the course of the precipitation reaction. (The details of precip-

Jan 1, 1961

By J. Chipman, T. Fuwa

The effects of various elements on the activity coefficient of carbon in liquid iron have been studied by two experimental methods: 1) equilibration with controlled mixtures of CO and CO2; 2) the solubility of graphite in the melt. Activity coefficient of C is increased by Al, Co, Cu, Ni, P, Si, S, and Srz. It is decreased by Cr, Cb, Mn, Mo, W, and V. THE thermodynamic properties of the iron-carbon binary system have now been fairly well established, although some uncertainty remains with respect to the exact location of some of the phase boundaries. The activity of carbon in ferrite and in austenite has been measured in the classic researches of R. P. smith' while similar measurements by Richardson and ~ennis, and by Rist and chipman3 have established the values of the activity of carbon in liquid iron up to 1760°C. On the other hand, our knowledge of the effects of alloying elements on the activity of carbon in dilute solutions is restricted to Smith's experiments on systems Fe-C-Mn and Fe-C-Si in the austenitic range and to some more recent experiments of schwarzman4 in the a range. In addition there have been a number of determinations of the effects of various elements on the solubility of graphite in liquid iron, and from these the corresponding effect in saturated solution may be obtained. The purpose of the present study was to extend the investigation of the liquid system to include the effects of alloying elements upon the activity coefficient of carbon, principally in dilute solutions. Equilibrium measurements were made on the reaction C + co, = 2 CO (g) The prepared mixture of CO and CO,, diluted with argon, flowed over the surface of the liquid metal which, after several hours' exposure to the gas, was quenched and anqlyzed. As in the earlier experiments, the principal experimental difficulty was in the deposition of carbon on the parts of the furnace at temperatures slightly below that of the metal bath. In order to minimize this difficulty, the ratio (Pco)2 /PCo2 was restricted to values not much higher than 100 atm, and correspondingly the carbon concentration in the metal seldom exceeded 0.30 pct. EXPERIMENTAL METHODS The method and apparatus were essentially the same as used by Rist and Chipman.3 The gaseous mixture consisting of highly purified CO, CO,, and argon, each controlled by a flowmeter, was led into the furnace and passed over the surface of the liquid-iron melt which was heated and stirred by high-frequency induction. One slight modification was made in that a molybdenum susceptor was placed outside the crucible for the sake of uniformity of temperature and to combat the tendency of carbon to precipitate on the crucible wall. Pure alumina crucibles approximately 25 mm ID were used. The charge consisting of about 30 g was made up of electrolytic iron, the alloying element to be added, and enough graphite to supply slightly more or less than the anticipated equilibrium carbon concentration. All metals used were of high purity. Metallic chromium, columbium, and vanadium were from special lots supplied by the Electro Metallurgical Co. Tin, copper, molybdenum, tungsten, cobalt, and nickel were of purest commercial grades. The electrolytic iron, after being cut to the proper size for charging, was prereduced by hydrogen at 850° to 1000°C to remove surface oxidation. The oxygen content of the reduced material was 0.002 pct. This treatment made it easy to control the carbon content of the initial melt. The charge was melted under the gas mixture to be used for the entire run. In some earlier melts the charge was melted under a stream of argon, but in this case some alumina was reduced from the crucible, and the aluminum thus absorbed in the melt was subsequently oxidized with the formation of a solid film of alumina on the surface of the melt. AS another safeguard against film formation, overheating of the bath was carefully avoided. All runs were made at a temperature of 1560°C. Under experimental conditions a charge of pure iron picked up 0.17 pct C in 3 hr and 0.23 pct C in 6 hr under an atmosphere for which the equilibrium concentration of carbon is 0.27. It is clear that the time required to reach equilibrium from an initially carbon-free melt would be very great. For this reason each experiment was started with a melt of known carbon concentration not far above or below the expected equilibrium value, and each melt was held at temperature for a period of at least 5 hr. Under such circumstances it was possible to chart the approach to equilibrium from both high-carbon and low-carbon materials. Temperature was controlled by frequent optical observation and adjustment and the metls were timed in such a way that the final 2 hr occurred during a time when electric power was steady; for example, 2 to 4 pm or after 11 pm. In melts containine volatile metals such as copper, tin, and mangane\e the time of holding was decreased somewhat in

Jan 1, 1960

By Charles Barron McIntosh

BECAUSE of the well known relationship between a low atmospheric pressure and increased amounts of methane in coal mines, attempts have been made to find associations between low pressures and coal mine explosions. An early study by F. Able disclaimed this relationship. He found that half the explosions took place during a rising barometer when methane content in a ventilated mine would be decreasing. A more recent study by C. L. Hosler revealed a close relationship between anthracite mine explosions and low atmospheric pressure. Bituminous coal mine explosions, where coal dust as well as methane can be exploded, were found to be more closely associated with a rising pressure following a low barometer than with the falling or low pressure period. Emphasis on rising pressure periods led the present writer to investigate the effect of the post-frontal or post-cyclonic weather on coal dust. Dust samples of uniform mesh were exposed in an Illinois mine. Analyses of the dust taken before and after the passage of cold fronts and their accompanying low pressure troughs indicated an increase in coal dust moisture prior to a frontal passage and loss of moisture from coal dust following the time of lowest pressure. Thus the warm, moist air (Tropical Maritime)found over the mine during the falling pressure period was cooled in the mine and moisture added to the dust. Cold, dry air (Polar Continental) accompanies' the rising barometer following a frontal passage and the air, being heated in the mine, subtracted moisture from the coal dust. A similar but seasonal phenomenon occurs from summer to winter, the dry dust period in winter being recognized as the more dangerous period. The question arose as to how the short period or daily changes in moisture content of coal dust compared with the seasonal changes. Temperature and humidity statistics were obtained from the surface and mine entry for the months of July andJanuary. The gain and Ioss of mdisture. to the hine were calculated for these two morths as were the gain and loss associated with mT (Tropical Maritime) and cP (Polar Continental),air masses as observed in the investigatiynsl. Temperature and humidity statistics tigatiynsl.taken from [the two air masses represent atimp span of only 34 hr. The redultant changes as presented in the accompanying table verify the supposition that short period changes in coal mine moisture may attain the magnitude of recognized dangerous seasonal changes. Statistics for the mT air and the July air have been placed next each other and those for cP and January air together for easier comparison of the two warm and two cold air units. The last column readily reveals that there is little difference in the amount of moisture being deposited in the mine from the mT air and the July average air. A similar conclusion is reached regarding the loss of moisture from the mine when it is affected by the cP air mass or the average January air. This comparison would be particularly true from late fall through early spring when strongly contrasting air mass changes are a common occurrence. The invasion of cold, dry air following a cold front thus produces a drying period that could well receive more attention as a danger period for coal dust explosions. This drying period would compare with Able's explosion period during a rising barometer. The drying period is also perltinent in Hosler's findings, where it was noted that the average explosion day (for bituminous coal mines) followed the day of lowest atmospheric pressure. Moreover, the author's investigation of some 365 coal mine explosions also indicates that this post-frontal period should receive special attention in connection with mine safety measures. Two comparatively recent major explosions in Illinois (Centralia and West Frapkfort) occurred after the mines had been under the influence of cold-dry air for 25 to 30 hr-following a deep low pressure passage. Dust was the important explosive element in both these explosions.

Jan 1, 1958

By Guy R. Johnson

In working brown iron-ore mines on the system employed at Longdale, namely, stoping from the top down, the usual procedure is to drive a succession of upraises from the lowest adit to the highest, or to the top of the deposit, as the case may be. These up-raises are usually driven 120 feet apart., along the strike of the vein,. As the work goes on, they are connected by levels, 10 feet spa* (vertically), and then serve as chutes. A transit is useless in surveying these chutes, and the writer has for several years made use of a hanging compass. The method of using this instrument, described in a former paper (Trans., xx.,.105), embracing as it does the use of a cord and several strips. of wood,

Jan 1, 1894

Jan 1, 1934

By L. Bombardieri, H. F. Mills

Iron King mine, producing gold-silver-lead-zinc-ore, is 10 miles east of Prescott, Ariz. At present the 1806 level is being developed. The echelon pat tern of ore deposit continues at depth but is less pronounced, and the orebody is now more or less continuous over 2600 ft of strike length, with widths 5 ft to as high as 26 ft where overlapping of lenses occurs in one section of the mine. Better continuity of ore at depth has encouraged systematic mining and improved plant facilities to offset higher operating costs. With favorable persistence of ore at depth, the three-compartment No. 6 hoisting shaft appeared inadequate to handle increased tonnage from greater depths, and in 1952, a four-compartment steel and concrete shaft was started. This is now at a depth of 1906 ft, and shaft pockets and loading cartridges are being installed on the 1806 level. Ore from the new shaft, hoisted in 5 ½ -ton Jeto bottom dump skips, is dumped into a 500-ton shaft bin, from which it is fed to a 16x30-in. gyratory crusher and conveyed 415 ft through an undersurface concrete gallery to the secondary crusher and conveying system supplying the 900-ton mill. Lead, zinc, and pyrite concentrates are floated, and the flotation tailings are cyanided after desliming. Waste from the new shaft is dumped into a 250-ton surge bin, fed from this bin to a 24-in. conveyor, and discharged into the glory hole above the block cave. The new shaft is served by a double-drum 400-hp hoist used for ore and waste; the No. 6 shaft conveys men and material.

Jul 1, 1956

Jan 1, 1895

By Horace V. Winchell

This paper, embodying information acquired by the writer in his work in connection with the Geological Survey of Minnesota, is presented by permission of the State Geologist. Historical.—On November 16, 1890, the workmen of Captain J. A. Nichols, of Duluth, Minn., encountered in a test-pit on the northwest quarter of section 3, township 58, range 18, west of the fourth principal meridian, the body of soft ore now called the Mountain Iron mine. Hard ore, chiefly magnetic, had been known for many years on the Mesabi range, and explorations made by Mr. E. W. Griffin, of Minneapolis, near the falls of Prairie river in T. 56-24 and T. 56-25, and by John Mallmann, at the Mallmann explorations, T. 59-14, had revealed some hard hematite interbedded with quartzite and low-grade soft ore; but this was the first discovery of merchantable hematite on the range. Captain Nichols had been exploring more or less along the range for some two years. To him and to the Merritt brothers, of Duluth and Oneota, who, unshaken in Faith by the discouraging reports of explorers, miners, experts, and geologists, had persevered in the search for ore, great credit is due for the final success, and large rewards have accrued to them already.

Jan 1, 1893

Jan 1, 1949