Search Documents

By William Loblowitz

A simplified system of flotation testing has been developed recently at the Bureau of Mineral Research of Rutgers University. The technique involves the known principle of skin flotation and can be used with minute quantities of sample and reagents in a beaker. A vessel containing the conditioned sample with added water and flotation reagents is held inclined and rotated slowly. Water-repellent particles come in contact with air and float on the surface of the liquid, while wettable particles are submerged. The float is poured off and filtered whereas the nonfloat remains in the beaker. The filtrate may be returned to repeat the process. This procedure can be made quantitative. Separations are obtained and are remarkably complete and repeatable. The effect of different reagents, optimum quantities, pH and other variables can be determined in a fraction of the time required for conventional testing. However, the method gives no information on the effect of frothers and the quality of froth to be expected in a cell, and it is not practical for particles finer than 200-mesh. Unlike other preliminary tests, separate float and nonfloat products are obtained, and their contents can be determined quantitatively by chemical analysis or grain counts. After the optimum reagent combination has been determined, the effect of fines and frothing may be verified in the conventional flotation cell. On the other hand, agglomeration-tabling can be directly duplicated from beaker tests. Procedure: Five to ten grams of sample are weighed into a 100-ml beaker. Flotation reagents and a small initial quantity of water are stirred together; additional water is then added to produce the proper water-solids ratio. The beaker is then tilted to 45" and rotated slowly. After three to five rotations, liquid and float are poured off and filtered; the filtrate may be recycled until the separation is completed. One test generally requires less than 10 min. Reagent concentration and pH remain quite constant because of the recycling of the filtrate. Two to four tests may be made simultaneously, and the effect of varied conditions may be observed by comparison. Considerable time is saved in preparation and handling since small quantities of sample suffice for a series of systematic tests. Repeatability One test was repeated four times under constant conditions. The sample used was a quartz sand containing approximately 24 pct feldspar and some clay aggregates. The +28-mesh grains had been screened out, and most of those finer than 100-mesh had been removed by hydraulic classification. The results are presented in Table I. For comparison, 500 g of the sample were separated by agglomeration-tabling using the same reagent combination and quantities as given in Table I. The weight percent float was 18.3 pct, composed almost entirely of feldspar and with only traces of quartz. Most of the remaining feldspar was recovered in a middling product with 2.2 pct by weight.

Jan 1, 1952

By Charles M. Brown, Russell Franks, W. O. Binder

Occasionally in the application of the austenitic chromium-nickel steels to corrosive conditions, failures have occurred by cracking without serious general over-all attack of the metal. As pointed out by Foyt and Scheil(1),2 and by Scheil, et al.(2) as well as by Hodge and Miller(3), the stress-corrosion failures that have occurred have been limited in number, and have taken place only when the steels were exposed to certain corrodents. These investigators have stated that while stress- corrosion cracking can be intergranular in nature and originate at the grain boundaries of the austenitic chromium-nickel steels, it can also take place in trans- granular fashion. They have shown that the cracking may be either initiated at the grain boundaries and may propagate along grain boundaries for some distance and then suddenly extend across grains, or it may begin in a transgranular fashion and suddenly proceed along grain boundaries until the cracking stops. Their data further show that when austenitic stainless steel is subject to intergranular attack, stress will concentrate and cause cracking in service. These investigators have studied the effect of the metals titanium and columbium which are added to the steels to impart immunity to intergranular attack, and molybdenum which is added to improve resistance to general corrosion.

Jan 1, 1945

By G. W. Bain

The Canadian magnesite deposits are situated in Grenville township, about 8 miles from Calumet station, on the Canadian Pacific Railway, but the poor transportation facilities have hindered their development. Magnesite was discovered in the boulders near White Rock Lake by Rev. W. P. Boshart in 1900. Observing that the material of these boulders was more glistening and whiter in color than Grenville limestone, he sent a specimen to the Department of Mines, Ottawa. An analysis showed this to be almost pure carbonate of magnesia and of commercial value if present in sufficient quantities. That summer, Boshart and McAllister found numerous outcrops, both of boulders and of bed rock, that gave promise of being magnesite of a commercial grade, and decided that this mineral deposit, if developed, would rival that at Veitsch, Austria. So they procured options on most of the land on which they knew the magnesite occurred. But the transportation difficulties were too great for the deposits to be mined at the prices offered for the product. In 1907, T. J. Waters organized the Canadian Magnesite Co. and opened a quarry on the north half of lot 18, range IX, and later on lot 15, range IX, of the same township. A lirnestone kiln was erected and the calcined rock was hauled to Calumet. In 1914, the North American Magensite Co, took over the quarries and shipped both crude and calcined magnesite until January, 1923. During 1915, S. Melkman organized the Scottish Canadian Magnesite Co. and opened a quarry on lot 15, ranges X and XI, Grenville township. A light, narrow-gage railway connects this quarry with the C. P. R. at Magnesite station. but shipments are made only during the summer months. Numerous other quarries have contributed to the output of the district but the greater part has come from the open pits of the

Jan 1, 1923

By Wolfram Ruff, H. A. Schwartz

The spheroidal form of the temper carbon nodules in malleable cast iron and of the graphite mottles of "mottled" cast iron suggests that in both all the graphite in a given mottle or nodule grew from a single center of crystallization or nucleus. $ There is, however, a distinct metallo-graphic difference between the mottle and the nodule; the area of mother metal impoverished in combined carbon by the crystallization of graphite in a mottle is practically coextensive with the ramifications of the graphite, while the impoverished zone of metal corresponding to a given nodule is always larger, and usually much larger, than the approximately spherical mass of graphite crystals forming the nodules. Furthermore, the mottle probably is formed during freezing and the nodule almost always at a considerably lower temperature. Assuming that the nodules or mottles can be used as a measure of the existing nuclei (capable of germination) we propose to record certain observations as to the graphitizing reaction in the light of the number and habits of growth of these nuclei. The present authors, in cooperation with others'-', have reported upon various cognate aspects of the problem. The fact that temper carbon is a mass of flakes and not a solid granule has become well recognized since the introduction of an improved polishing technique8, 9, 10 for cast iron. The problem of deriving from the circular planar intercepts of a mass of spheres of varying sizes their number and size distribution in space has also been satisfactorily solved12, 13 Growth of Nuclei in White Cast Iron It has already been shown1, 3 that the progress of graphitization with time is usual1y consistent with the assumption that nodules grow in size

Jan 1, 1936

By R. W. Kraft

The normal Mg-Mg,Sn eutectic is a classic example of a Chinese script eutectic. When the alloy is unidirectionally solidified, a much simpler topo-logical arrangement of the phase particles can be produced although individual grains still usually consist of two or more interpenetrating lamellar systerns. Specimens from unidirectionally solidified ingots were analyzed metallographicall~ and crys-tallographically, and it was found that the interfaces between the lamellae had a common crystallograPhic character describable by: Lamellar interfaces II {220}Mg2Sn 1) {1011}Mg Arguments are presented to explain why this particular orientation relationship tends to occur and it is shown that this criterion can be nearly satisfied simultaneously on up to four different lamellar systerns between two interpenetrating single crystals. Finally, on the basis of this work ad other similar work which has previously been done on Al-CuAl2 eutectics, a general principle pertaining to low-energy interfaces between two crystalline Phases is proposed. WITHIN the past few years several investigators1-4 have demonstrated that the microstructures of many eutectic alloys can be significantly altered by uni- directional solidification. If appropriate control is exercised over the purity of the alloy, the growth rate, and the thermal gradient during unidirectional solidification, ingots can be made in which the phase particles are aligned predominantly parallel to one another throughout substantial portions of the ingot. The present author has also shown for at least one of the alloys that the parallel lamellae tend to assume a unique crystallographic relationship during

Jan 1, 1963

By H. A. Wriedt

Zinc-vapor pressures in equilibrium with bcc solutions of zinc and iron at 703.5", 757", 793", and 900°C were measured by an isopiestic method. Thermody-na?nic properties of zinc in these solutions were derived directly and those of iron with a Gibbs-Duhem integration. Zirzc and iron exhibit large, positive, and moderately temperature-sensitive deviations from ideality. Excess enthalpies and Gibbs energies are positive in the ranges studied. It has been establzshed in relating published phase equilibria to the Gibbs energies of forming solid solutions that positive departures from ideality also exist in the fcc solutions. Tlze stability, as defined by Darken, of the bcc solutions is small but positive at 703.5"C. Its decrease with decreasing temperature indicates that a miscibility gap may exist in the stable or metastable bcc solutions at lower temperatures. The changes of thertnodynanlic properties relatable to changes in magnetic state are minor compared to other changes due to alloying. The accuracy with which the relation between lattice parameter and composition of the bcc solutions is known has been improved. Zinc increases the lattice parameter of a iron by O.ZOZA per unit atom action zinc to at least NZn = 0.25. TO our knowledge, only Ciganl has previously investigated thermodynamic properties of the bcc solutions of the Fe-Zn system. He measured zinc-vapor pressures in the temperature range from about 320" to 360°C by an effusion technique. We have measured the vapor pressures of zinc in equilibrium with bcc solutions of zinc and iron at 703.5", 757", 793", and 900°C by an isopiestic technique. This investigation and the pursuant thermodynamic computations are part of a program for studying several properties of these solid solutions. In the appendix we report a remeasurement of the relation at room temperature between the lattice parameter and zinc content. Related work not reported herein embraces measuring the diffusivity2 of zinc in ferrite at 700" to 900°C and the Curie point temperature3 as functions of composition. EXPERIMENTAL METHOD AND APPARATUS Purified iron at a series of constant temperatures was saturated with zinc at a series of constant zinc-vapor pressures, the range of conditions being so limited that the equilibrated solid solutions were ferri-tic. The equilibration was conducted in long capsules, Fig. 1, that had been evacuated, gettered with titanium, and sealed. The purified iron, part of a vacuum-melted ingot of electrolytic-iron stock (Glidden Co. 1044-grade), had the impurity contents listed in Table I. It was used in the form of millings about 0.001 in. thick. A zinc of 99.999 pct purity (United Mineral and Chemical Corp.) and later one of 99.9999 pct purity (Cominco Products, Inc.) were used, with no observed difference in results. Sufficient zinc was placed in the capsule (separate from the iron and kept at a different temperature) to supply the vapor phase and the iron alloy, while leaving a pool of pure liquid zinc throughout the run. The imposed temperature of the residual zinc pool fixed the vapor pressure of zinc throughout the capsule; condensation was avoided at other locations by making this the lowest temperature in the capsule. Two common complications of nonisothermal systems were, we believe, effectively absent from ours: first, molecular species other than monatomic have no appreciable concentration in zinc vapor at 700" to 900~~: second, the development of zinc-pressure differentials in the capsules was suppressed by use of relatively large-diameter tubing and the absence of diluents in the zinc vapor other than desorbed impurities. The specimens and zinc pool were located at two isothermal zones (each ranging within 1°C over several inches) of a wire-wound, 37-in.-long vertical-tube furnace. The required temperature distribution was achieved by external adjustment of the currents in three electrically isolated windings. The temperatures of the isothermal zones were controlled independently by ther-

Jan 1, 1968

By F. C. Miller

THE metallurgical fuel of Colorado, Utah, and New Mexico has been a very tardy member in the caravan of western industrial progress. The history of western coke has naturally been closely related to the development of the metallurgy of iron and steel and the precious metals, in the State of Colorado. It was at Leadville, with a population of 300 in 1877, that the Sentinel was published by Richard S. Allen. The Sentinel gave very full accounts of the various mineral discoveries at the new town of Leadville, which found their, way to the more widely circulated journals of the East, and attracted the attention of many people. At the close of 1878, a census showed a total of 5040 persons. The first smelter was established in 1877, at Malta, two miles from Leadville, by A. R. Meyer, but was not successful. It was succeeded by the Harrison Reduction Works, in 1878. The La Plata began with one furnace in June, 1878, and in 1879 had four furnaces in active operation. These furnaces used charcoal for fuel, and, because of hot tops, suffered a tremendous loss in lead and silver. This difficulty was overcome by the erection of 50 single-bank 10-ft. beehive ovens at Crested Butte, Colo., in 1880. The slack coal sent to these ovens was very pure, and yielded a coke carrying as little as 4.5 per cent. ash. Among the pioneers in the Leadville district were Grant, Eddy, James, Billings, Eiler, and Dickson. To these men the West owes the present expansion of its mining industry, and the erection of metallurgical processes for the treatment of precious metals.

Jan 8, 1918

By William A. Johnson

THE mathematical analysis of diffusion curves in solid metals is Carried out ordinarily by analogy with the flow of heat in a continuous medium and no account is taken of the fact that the materials involved are composed of discrete particles that move discrete distances at irregular intervals. It is possible to treat the problem on the basis of simple assumed atomic mechanisms, in which case, because of the small scale of the elementary process compared to the gross effects observed experimentally, the two procedures lead to the same expression for the variation of concentration with distance. Thus, for engineering purposes, the usual methods are quite satisfactory. If, on the other hand, our purpose is to go beyond the mere collection of data, however desirable this may be, it is necessary to recognize and understand the factors that are of fundamental importance. One factor that has not hitherto been considered when dealing with solid metals is the difference in atomic weights of the isotopes of a single metal. While all the atoms of a given element are alike chemically, their weights may vary by a small but significant amount, and atoms of different weights may have different diffusion rates. With gases this variation in isotopic weight produces a change in the rate of diffusion by a factor inversely proportional to the square root of mass. While, except for the lightest gases, this is not a large effect, it is, for example, sufficient to permit a considerable concentration of one isotope at the expense of others. If metals exhibit a similar phenomenon, some modification of the analysis of the diffusion process will be required, since the different isotopes of a given metal will have different probabilities of moving and the heat-flow analogy will contain a fundamental error. This situation cannot be rectified by using a diffusion coefficient based on the average probability of moving, and it can be shown that even when the diffusion coefficient is independent of composition, the diffusion curve will not agree with the simple theory except in the rare cases where only one isotope exists; e.g., gold. If, however, the mass effect in the solid state were no larger than in the gaseous, the errors arising therefrom in the analysis of ordinary diffusion curves would be quite negligible. Nevertheless, our desire to obtain all possible information concerning the details of the diffusion process, and the possibility of diffusion in the solid state as a means for separating isotopes are cogent reasons for undertaking an experimental study to determine whether isotopes of different masses diffuse at different rates. EXPERIMENTAL PROCEDURE If isotopes of different masses diffuse at different rates, the ratio of the concentration of one relative to another will vary with the distance from the diffusion inter-

Jan 1, 1946

By Charles R. Keyes

PAGE. I Introduction,........674 11. Occurrence............ 676 III. Geology of Death Valley BoRate-Region,....677 1. Surface.Relief ......677 2. Geologic Formations,....680 3. Geotectonics,..684 IV. FURnace Canyon Deposits..686 1. General Features..686 2. Geologic Structure..688 3. Ores.....690 4. Typical Section ...691 V. Lost Valley Deposits...693 VI. Mojave Desert Deposits..693 1. Distribution....693 2. Geologic Structure ........694 3. Ores............ 696 VII. Santa Clara Valley Deposits .699 1. Distribution....699 2. Geologic Structure..700 3. Ores.....700 VIII. Ventura County Deposits..701 IX. Geologic Occurrence of Borax .701 1. Original Sources...701 2. Solfataric Borax...702 3. Lacustrine Borax...703 4. Marsh Borax....703 5. Terranal Borax...704 X. Chemistry of Natural Borates.... 705 1. General Considerations.....705 2. Composition of Saline Waters...706 3. Solubility of Components....707 4. Time-Element in Water.Concentrations . 707 5. Effect of Temperature.....708 6. Effect of Pressure......709 XI. Occurrence of Other Commercial Salines,.... 709 I. Introduction. A complete transforrnation has taken place in the borax industry during the year 1908. A most remarkable factor in

Jan 1, 1910

By G. R. Mansfield

THE third year of Government exploration f or potash by the U. S. Geological Survey and-the U. S. Bureau of Mines under the authorization of the act approved June 25, 1926 (Public 424-69th Cong.) is drawing to a close. The results thus far obtained are thought to be sufficiently interesting and satisfactory to justify the presentation of a brief preliminary account of the work. REVIEW OF EARLIER EXPLORATION The general geologic similarity of the Permian basin of Texas and New Mexico to the potash field of Germany had long ago suggested the possibility of the presence of potash salts somewhere in that basin, but petroleum exploration was then making little headway there and the necessary data could not be obtained. The discovery by Udden in 1912 of potash in brine from the Spur well in Dickens County, Texas, was the first direct evidence of its presence. In 1915-17 the U. S. Geological Survey drilled a test well with standard tools at Cliff side near Amarillo, but failed to find potash. Nevertheless, an observer has been kept in the field, at first in cooperation with the Texas Bureau of Economic Geology but since 1922 by the Survey alone, to `secure data and samples from oil and gas tests. Since the discovery of oil in Reagan County in 1923 exploration by drilling has been rapidly extended to many parts of western Texas and southeastern New Mexico. The identification of the potash-bearing mineral polyhalite was first announced by the Geological Survey in June, 1921, the material having come from cuttings from the Bryant well in Midland County and the Burns well in Dawson County, Texas. Successive discoveries and announcements of similar purport aroused widespread interest in potash exploration, which culminated in the action by Congress already noted.

Jan 1, 1929

By J. K. Stanley

Knowledge of the diffusivity of carbon in the low temperature form of iron (alpha iron existing below 910°C) is at the moment of considerable interest in the study of the decomposition of austenite and martensite, the elastic after-effect,123 the magnetic after-effect4 and the decarburization of steel below 910°C. Information on the solubility of carbon in iron, and to a lesser extent its diffusion, is also important in consideration of such phenomena as blue-brittleness, temper-brittleness, "magnetic" aging, quench-aging, strain-aging, and possibly the yield point. In order to obtain more information on these subjects more fundamental knowledge is necessary. It is the purpose of this work to present data on the diffusion and solubility of carbon in the alpha iron. The high temperature form of iron (gamma; face-centered cubic) existing above 910°C is capable of dissolving relatively large amounts of carbon, up to 1.7 pet at 1130°C, while the low temperature form (alpha, body-centered cubic) existing below 910° dissolves only a limited maximum amount of less than 0.02 pet carbon at 725°C, according to data obtained here. Since the solubility of carbon in the face-centered or gamma iron is large, relatively speaking, no great analytical difficulties have been encountered in the determination of the solubility lines5 or of the diffusion of carbon.0 The limited solubility of carbon in alpha iron offers difficulties because experimental procedures and analytical methods for low carbon contents below say 0.01 pet have to be more refined than techniques used for work with gamma iron. Because of the difficulties of applying conventional methods to the determination of the diffusion of carbon in alpha iron, virtually no work has been done on this subject. However, by proper refinement of the analytical method for small amounts of carbon, the determination of the diffusion coefficient can be made readily using modified procedures. The solubility of carbon in alpha iron has been determined over a temperature range by various investigators, but the agreement among them is poor. The present investigation establishes the limits quite accurately. Information of this kind is useful in establishing the correctness of equilibrium diagrams but, more significantly, such information on maximum solubilities, especially when extended to alloyed ferrites, should be extremely important in the study of aging and related phenomena. Literature The literature existing on the diffusion, in particular, and on the solubility of carbon in alpha iron is not extensive. The data which exist are not of a high order of accuracy, much of them being in the realm of conjecture. THE DIFFUSION OF CARBON IN ALPHA IRON Whiteley7 made the qualitative ob- servation, using metallographic techniques, that the rate of diffusion of carbon at the A1 (725°C) point was very rapid and that its diffusion was still rapid at 550°C. Snoek,4 studying the magnetic aftereffect in high purity iron, arrived at the conclusion that the after-effect could be explained by the presence of small amounts of carbon diffusing under the influence of magnetostrictive strain (lattice distortion due to magnetic interaction). In later work, Snoek8 made an estimate of the ratio of carbon diffusion in alpha to its diffusion in gamma iron, and concluded that for a temperature of 910°C the ratio of Da/D? was 2600. Polder,9 basing his calculations of D on relaxation phenomena in the elastic after-effect, estimated that Da is about 1/3 of D? at 910°C (1183°K) and is about 1/12 of Dy at 727°C (1000°K). Polder's equation for the diffusion of carbon in alpha iron was calculated to be 18000 D = 5.2 X 10-4 e-RT cm2 per sec Ham10 obtained data for the diffusion and solid solubility of carbon in alpha iron at two temperatures by using one technique similar to that employed in this study. He found a D of 8.0 X 10-7 cm2 per sec at 702°C and of 2.7 X 10-7 at 648°C. THE SOLUBILITY OF CARBON IN ALPHA IRON Although pearlite is absent in steels containing 0.06 pet,11 0.05 pet,12 or 0.045 pet C,13 it appears that the carbon in these steels cannot be in solution in ferrite. The solubility of carbon at the A1 (725°C) point was first determined by Scott14 on the basis of cooling curves, and was found to be between 0.03 and 0.04 pet C. Tamura15 by interpolating between the solubility of carbon in delta iron at 1400°C and in alpha at room temperature (assuming zero solubility) ar-

Jan 1, 1950

Discussion of the paper of George K. Burgess, J. J. Crowe, H. S. Rawdon, and R. G. Waltenberg, Finishing Temperatures and Properties of Rails. By Albert Sauveur, R. Trimble, William R. Webster, P. H. Dudley, George B. Waterhouse, M. H. Wickhorst, James Aston, E. F. Kenney, A. W. Gibbs, W. A. Aiken, and G. K. Burgess . . 767 Discussion of the paper of Albert Sauveur, Manganese Steel and the Allotropic Theory. By G. K. Burgess and J. E. Stead 787 Discussion of the paper of J. V. Emmons, The Surface Decarbonization of Tool Steel. By Albert Sauveur, Bradley Stoughton, E. G. Spilsbury, Oliver W. Storey, H. O. Hofman, and J. V..Emmons 790 Discussion of the paper of Richard H. Rice, Turbo Blowers for Blast-Furnace Blowing. By S. G. Valentine, W. McA. Johnson, L. Iversen, J. E. Johnson, Jr., Karl Nibecker, W. Trinks, Otto Banner, H. S. Braman, Arthur G. McKee, and Richard H. Rice . . . 794 Discussion of the paper of J. K. Furst, The Plant of the Duplex Process for Making Steel. By W. McA. Johnson, Arthur G. McKee, Henry D. Hubard, and Bradley Stoughton . . 810 Discussion of the paper of E. C. Harder, The Iron Industry in Brazil. By I. C. White and E. C. Harder 813

Jan 4, 1915

By R. W. Raymond

The name of Oswald J. Heinrich first appears among the members of the Institute in the first volume of its Transactions, which records that lie was elected at the Boston meeting, in February, 1873. That name has stood ever since upon our catalogue of active members. It has appeared frequently in the reports of our debates. It has been attached to many interesting and important professional papers. Henceforward it must hold a place, silent but significant, ill the pathetic lengthening list of our departed. From a present

Jan 1, 1886

Jan 1, 1928

Jan 1, 1889

By R. W. Raymond

Most of US, in this hurrying age, take little pains to preserve such records of our doings as will make the work of' our biographers easy. Now and then there is an exception, and Dr. Trippel was one. Methodical in all his habits, he kept diaries and journals comprising his own personal experiences, the details and results of his numerous scientific investigations, and his impressions concerning men and events; and also copies of all his technical essays, published by various societies or periodicals. It is a striking instance of " the irony of fate," that these carefully-preserved materials, which would now have a real historical, as well as biographical value, were totally destroyed by an accidental fire a few years ago. In addition to my own recollections of an acquaintance covering more than thirty years, I am indebted, for the fads upon which this sketch is based, chiefly to Mr. Engene J. Trippel, a son of the deceased, and now Register of the United States Land Office at Tucson, Arizona. Mr. Trippel, however, frankly confesses that his own knowledge of his father's work is, in the absence of written records, imperfect.

Jan 1, 1898

By A. N. Khayyat, R. G. Temple, R. Skelton

The fluid energy mill has been in use since the 1930's when an early patent was granted to N.H. Andrews in the USA. The microniser design has been basically unaltered since that date and current designs such as the Airfilco "Micronizer" have been progressively developed from results based on wide experience. The authors have been engaged in a research programme to establish optimum design and operational parameters for the Micronizer so as to provide a more quantitative basis for scale-up prediction of results. An introductory section will first trace the development of fluid energy milling including reference to other designs which have developed alongside the micronizer (especially the “Jet-o-miser"). With regard to design features the number of fluid injection nozzles and their size was investigated to establish the optimum range. Injection angle and, the consequent diameter of the internal "tangential circle" was carefully studied to determine the effect of this parameter on product size. The research was carried out using fine limestone as the test material with air as the grinding medium. Feed size fractions of 0-120µm, 0-250µm, 0-500µm, and 300-600µm were milled and product size analyses were carried out using the Coulter Counter technique.

Jan 1, 1980

There were present eleven Directors, the Secretary and Assistant Secretary of the Institute, and eleven guests. The Secretary, Bradley Stoughton, was appointed the representative of the Institute on the Board of. Directors of the American Bureau of Welding. A communication from a member of the Institute regarding simplified spelling was laid on the table. The following appropriations were made for the year. 1919: $250 to the Institute of Metals Division, $250 to the St. Louis Section, $100 to the Columbia Section. An invitation was received from the Western Society of Engineers to the Institute to use the facilities of that society during the A. I. M. E. Meeting in Chicago. The Bulletin of the Institute was presented to the French Congress of Engineers. There were elected twenty-eight members, eighteen associates, and three junior associates. The status of one member was changed from junior associate to associate. Four members were reinstated. An extension of time was granted to one member for payment of dues. The dues of four members on active military duty were suspended. Dues were remitted of four members who have been paying over thirty years, and who are each over seventy years of age.

Jan 5, 1919

By Stephen Krickovic

AS it is commonly understood in the bituminous coal mining industry, pillaring means removal, as completely as is practical, of all pillars formed in the development of headings and rooms on first mining. The degree to which this can be accomplished, termed percent of recovery, is of course dependent generally upon the physical conditions of the bottom and the overburden, the system of min-

Jan 1, 1956

By P. Duwez, H. Martens

Dimensional changes generally occur during the sintering of metal powder compacts. These changes may have several causes and their magnitude depends upon the numerous variables involved in the process, such as the nature of the powder, size and shape of the grains, compacting pressure, rate of heating, maximum temperature, length of time at temperature, and furnace atmosphere. Among all the variables, time, temperature, and compacting pressure are probably the most important ones, and the effect of each one of the other variables can be studied separately once the effect of these is well understood. The most precise method of studying the phenomenon of dimensional changes in a compact consists of heat treating the compacts at various temperatures for different lengths of time. In this method, only very small specimens can be used, in order to achieve rapid rates of heating and cooling. The technique involved in these measurements is very simple, but is time consuming. Another experimental approach to the problem consists of measuring the change in length of a compact as it is being heated at a constant rate. Although the two variables, time and temperature, are combined into a single one (rate of heating), the results obtained by this technique may be of great interest from both practical and theoretical points of view. The purpose of this paper is to describe a systematic investigation of the change in length during sintering of compacts made of one or several metal powders. Experimental Procedure The change in lenght of compacts during sintering was measured with an automatic recording dilatometer. In this instrument the change in length and the temperature are recorded as functions of time on two separate charts and the rates of heating and cooling may be varied from 1 to 20°F per min. The temperature may be kept constant at any value up to 2200°F during any predetermined length of time and the change in length recorded as a function of time. Provision is made for atmosphere control inside the fused silica tube containing the specimen. Three different magnifications are provided, so that 1 in. on the chart corresponds to 0.002, 0.005, or 0.010 in. change in length. The mechanism following the change

Jan 1, 1950