Search Documents

Jan 1, 1935

By N. N. Breyer

A specially built "hard" tensile machine with characteristics permitting the precise detertnination of the drop of the load at the yield point has been used to study the magnitude of the yield-point phenotnenon in prestrained martensitic 4340 steel. A new phenonzenon, the appearance of a secondary yield point, has been observed by holding the specimen at constant strain in the plastic region. Furthermore, it has been found that a series of yield-point drops could be introduced by successive constant strain holds in the plastic region. The isothermal kinetics of the development of the secondary yielding point lave been studied at four temperatures: 24° 0° -18°, and -79°C. From the results of the kinetic investigation, equations for the In a previous investigation1 it was shown that, contrary to generally held opinion, steels of medium carbon content, such as 4340, 4140, and 86B30, in the as-quenched martensitic condition, can be cold-drawn through a die with reductions in area of up to 10 pct without cracking. Tensile specimens of 4340 machined from bars quenched and prestrained in this manner exhibited tensile strengths of about 400,000 psi coupled with 30 pct reductions in area. In addition, it was found that each sample of such steels exhibited a yield point in the quenched, cold-drawn condition. Since these studies were conducted on a commercial hydraulic testing machine of a type which is not well-suited to detailed study of yield-point behavior, it was decided to study this phenomenon more thoroughly on a rigid straining machine. In this new investigation, use of such a "hard" machine not only allowed study of the magnitude of the yield-point drop but also revealed a new phenomenon—secondary yielding of the martensite introduced by stopping crosshead motion after plastic deformation of the sample had begun. The present paper is a report of these findings. MATERIALS AND PROCESSING The material used was a commercial 4340 steel of the composition shown below: 0.41 0.80 0.013 0.019 0.31 0.85 1.76 0.28 1 0.42 0.77 0.015 0.024 0.30 0.84 1.69 0.28 0.08 2 1 = Ladle analysis. 2 = Laboratory analysis. Bars of this steel were processed in the following way: 1) machined to predetermined diameters; 2) austenitized at 870°C for 1 1/2 hr; 3) oil-quenched; 4) cooled to -115°C for 1/2 hr; onset and increase in magnitude of the secondary yielding in this temperature region have been found to fit the relationship ?Ys = Atn where ?Ys is the magnitude of the secondary yield Point in psi, t is the time in seconds, and A and n are parameter characteris-tics of the material. Although the occurrence of the primary and secondary yield points could be rationalized qualitatively on the basis of stress-induced ordering of carbon atoms in the stress fields of dislocations, as postulated in an earlier paper, the kinetics of the secondary-yield-point development were interpreted to indicate that the ordering involves more than just single jumps of carbon atoms from high-energy to neighboring low-energy sites. 5) pickled and lime-coated; 6) drawn through a carbide die. The predetermined diameters were chosen so that drawing through the same die gave the various reductions desired. Tensile specimens of 0.252 in. diam with a 1 1/4 in. gage length were then prepared from the drawn bars and tested. In order to study the stress-strain behavior at the yield point in detail, a rigid tensile machine with a high spring constant was constructed. Columns of large cross section (relative to the specimen cross section) constituted the machine frame. A dc motor was used to drive a screw via a gear reducing train and a "crane" thrust bearing. In this relatively simple device small deformations could be observed un-blurred by the slow response and lower spring constant inherent in hydraulic machines.' A strain-gage dynamometer permitted load changes as small as 8 lb to be read. RESULTS Tensile test samples machined from bars in the as-quenched condition with no subsequent drawing and samples from bars with 3.8 pct reduction after quenching gave stress-strain curves typified by those shown in Figs. I and 2. The time lapse between predrawing and tensile testing varied but usually ranged between 3 to 6 days at room temperature. The strain rate during testing was 0.003 in. per in. per min. The as-quenched curve is seen to have a broad serrated maximum whereas the stress on the specimen prestrained 3.8 pct rose linearly to point A, Fig. 2, fell abruptly to B, and then gradually to C. The abrupt drop to B was accompanied by evidence of incipient necking. The drop of the stress at the yield point in the prestrained samples (A to B in Fig. 2) changed with the percent prestrain, as illustrated on Fig. 3. Although the tensile strength increased continuously with the amount of previous cold drawing, the magnitude of the yield point drop first increased—up to about 6 pct prior reduction—and then decreased. Specimens from bars predrawn more than 8 pct broke in a brittle fashion in the elastic portion of the stress-strain curve.

Jan 1, 1967

By N. J. Grant, B. C. Giessen, R. Koch

The system Nh-Ir was investigated over the complete concentration range by metallography and X-my techniques, using forty one alloys. The solubility limits of terminal and intermediate phases and the solidus temperatures were determined. Five intermediate phases were found: a Nb3Ir, cubic, Cr3O type; tetragonal, ofecr thorhomhic, isostruc-turn1 with (ta-Rh); and a Nhlr3. cubic, AuCu, type. a Nb3lr and a Nbfr3 melt congruently; three eutectic and three pentectic reactions occur. The phase diagram of the Nb-Ir system had not been fully treated in the literature; only surveys of intermediate phases were found.1"5 In this study, the details of the phase boundaries were investigated as well as the crystallography of the intermediate phases. EXPERIMENTAL METHODS The experimental procedures such as arc melting of powder compacts, heat treatments, solidus measurements, X-ray, and metallographic observation were identical with those used in the work on the Nb-Rh phase diagram.&apos; They will therefore not be repeated here except where the conditions differed. The purity of the niobium powder was as stated in Ref. 6; the iridium powder of 99.9+ pct purity from J. Bishop and Co., Malvern, Penn., did not contain impurities exceeding 100 ppm, except rhodium (200 ppm). The melting points and vapor pressures of both elements are very similar. This fact contributed to a very small weight loss on melting and facilitated preparation of homogeneous alloys. As shown in Ref. 6 for Nb-Rh, no oxygen pick-up exceeding 200 ppm had to be considered; this was regarded as valid also for Nb-Ir. A total of forty one alloys were used in the determination of the phase diagram; their concentrations are shown in Fig. l, which presents the phase diagram. The concentration limits as determined by the weight-loss method averaged <0.2 at. pct, and never exceeded 0.5 at. pct. Heat treatments were carried out as described in Ref. 6. Depending on the concentration, only tantalum, tungsten, or iridium containers were employed, avoiding oxide crucibles altogether. Alloys from 0 to 25 and from 65 to 100 at. pct Ir were homogenized at 2095°C for 15 hr, intermediate compositions from 25 to 65 at. pct Ir for 65 hr at 1780°C. A typical annealing-time schedule is presented in Table I. Solidus points were measured as described in Ref. 6 with the modification that samples rich in niobium were held between pieces of tantalum foil and samples of high iridium concentrations were held between rhenium platelets or in iridium wire. After each run it was ascertained metallographically that no reaction with the holder had occurred. Rhenium was selected as holder material after it had been shown in separate tests that the melting points of Re-Ir alloys rise continuously from 2440°C. Metallographic examination was carried out as described in Ref. 6, and the same procedure and etchants were used successfully. While metallographic discrimination between a Nb3lr and o was easily possible, X-ray diffraction was necessary to separate al and ct2. X-ray powder patterns were taken and evaluated as for Nb-Rh6 yielding the error limits indicated in Table 111, to be introduced later. For the determination of the invariant reactions and phase boundaries, the same techniques as for Nb-Rh6 applied. The general accuracy of invariant concentrations is regarded as somewhat higher than for Nb-Rh due to the small slope of most solvus lines.

Jan 1, 1964

By M. M. Fidlar, Ralph E. Esarey

Conditions in the oil and gas industry in Indiana were somewhat better in 1936 than in the previous year, owing in large part to increased

Jan 1, 1937

By Charles W. Goodale

The purpose of this paper is to review the history of the Drumlummon, one of the famous old mines of the West. Mining engineers, when sent to examine new mines in old districts, or, to decide whether an old property, under new conditions, will pay to reopen, have had difficulty in learning anything authentic regarding workings which are under water, and historical facts about the working character of the ore, the total production, and the value of the ore with increasing depth. &apos;Not many years elapse after the pumps are pulled, before maps, books and records are destroyed, and the value of the publications of the Institute would be increased if they contained the history of many old mines now abandoned. The unsuccessful efforts of the writer quite recently in trying to obtain reliable information about a gold mine which was reported to have produced several million dollars between 1880 and 1888, the workings of which are now partially caved and under water, impressed upon his mind the desirability of having a permanent record of old properties. In this particular case, the owners insisted that under present conditions of improved methods of treatment —particularly by the use of cyanide, which was not an applied process when the mine was operated, the property could be made to pay a handsome profit on ore left in sight in the old workings, but no assay records could be found to confirm these assurances, and even the records of bullion shipments had been destroyed. If surveys and maps were made as the work progressed, no trace of them could be found, and therefore opening of the ground through a new shaft and drifts therefrom would be attended by some risk while exploring near the old workings. Fatal accidents by flooding under these conditions have occurred, and as an evidence that miners have fears of such dangers, it was urged upon the Mining Committee during a recent session of the Montana Legislature, by a delegation of

Jan 1, 1915

By A. E. Dwight, A. F. Berndt

Binary and ternary alloys of uranium with transition metals were prepared with U2X stoichiometry. The compounds U2Tc, U2Rh, U2Os, and U2lr were formed by peritectic or peritectoid transformations, and were shown to be isostructural with U2Ru. The lattice constants are presented. Miscibility relationships obtained from the study of ternary alloys are graphically summarized in terms of an area-of-stability plot. The compound U2Re is not isostructural with either U2Ru or U2Mo. A series of compounds with stoichiometry U2X has been prepared in which X is technetium, rhodium, rhenium, osmium, or iridium. The only other U2X compounds, for which X is related to the above transition metals by proximity in the periodic table, are U2Mo and U2Ru. The structure of U2Mo is the tetragonal C11b type (MoSi2 type)1 and U2Ru is monoclinic, with a new structure type.&apos; This investigation was undertaken to determine if any of the above compounds are isostructural with either U2Ru or U2Mo and to find the range of occurrence of these phases. EXPERIMENTAL Alloys were prepared from stoichiometric amounts of electrolytic uranium (99.99 pet pure) and transition metals of 99.5 pet purity (98+ pet pure Tc), by arc melting on a water-cooled copper hearth under an Ar-He atmosphere. Weight losses were negligible. The buttons were homogenized at temperatures between 700o and 800°C (900°C for U2Tc) in evacuated capsules and air-cooled. The X-ray powder specimens were annealed briefly at the temperature of homogenization. Except in the case of the technetium alloy, metallographic examination was used to determine the number of phases present. The radiation hazard involved in handling technetium precluded the use of metallography to examine U2Tc. The temperature and mode of formation of the U2X phases were determined by heating the metallographic specimens to successively higher temperatures, until examination indicated the presence of chilled liquid or a peritectoid transformation. RESULTS The U2X compounds investigated were found to be formed under the following conditions: UzTc unknown U2Ru peritectic 897o ± 3°C U2Rh peritectoid 755o ± 5°C U2Re peritectoid3 below 750°C Uas peritectic4 920°C U2Ir peritectoid 775o ± 5oC Debye-Scherrer patterns for the above U2X phases were made with CuKa radiation (nickel filter). The similarities in the positions and intensities of the strongest lines in the front-reflection region strongly suggested that U2Tc, U2Ru, U2Rh, U2Os, and U21r are isostructural with only minor differences in the unit-cell dimensions. The known lattice constants and intensities of the Debye-Scherrer rings for U2RU2 were used as a guide in order to index the low-angle X-ray reflections of the U2TC, U2Rh, U2Os, and U2Ir powder patterns. Approximate lattice constants for these compounds were thus obtained and were used along with the intensities observed for U2Ru to index the strongest lines in the back-reflection regions. A sin2 2? correction term was included and the lattice constants were refined and standard deviations estimated by least squares. Comparison of observed and calculated values of Q(= 4 sin2?/?2) used in these calculations are given in Table I. In each case when the positions of lines could not be resolved on the films they were not measured. The final lattice constants, with their standard deviations, are given in Table 11, along with the unit-cell volume and X-ray density. The values of the atomic volume5 of the transition ele-

Jan 1, 1965

Organization Place Date 1919 American Chemical Society Philadelphia, Pa. Sept. 2-6 National Assn. of Stationary Engineers Huntington, W. Va. Sept. 8 American Peat Society Minneapolis, Minn. Sept. 22-24 American Iron, Steel Electrical Engineers St. Louis, Mo. Sept. 22-26 American Institute of Min. and Met. Engineers. Chicago, Ill. Sept. 22-27 American Steel Treaters&apos; Society, First Annual Convention Chicago, 111. Sept. 22-27 National Exposition of Chemical Industries.... Chicago, Ill. Sept. 22-27 National Safety Council Cleveland, O. Sept. 29-Oct: 2 American Foundrymen&apos;s Association Philadelphia, Pa. Sept. 29-Oct. 4

Jan 9, 1919

By W. D. Smith

It has been 5 years since the writer left the Philippine Islands and while in that country his chief work did not lie in this field, though he has visited all but one of the localities mentioned in this article. The principal field studies relating to oil were M de by his colleague, Mr. Wallace E. Pratt. The writer&apos;s investigations ealt with the general stratigraphy and paleontology of the Philippines. with the exception of the investigations made by Mr. Pratt and the writer very little information on this subject is available. A number of geologists in the employ of large oil companies have visited the Islands from time to time but, following the general rule, the public has scarcely ever been permitted to learn anything of the results. The writer is indebted to the Bureau of Insular Affairs, Washington, for late information regarding recent legislation in the Islands relating to petroleum. All the known oil seeps, petroleum residues, such as ozocerite, and natural-gas emanations are associated with Tertiary sediments. The chief seeps and most promising prospects are located as follows: 1. Bondoc Peninsula (lower end), Tayabas Province, Southeast Luzon. 2. The west coast of the island of Cebü from Alegria north to, and perhaps beyond, Toledo. 3. Central Mindanao not far from Lake Lanao. 4. The ozocerite veins on the Island of Leyte in the northwestern part in the vicinity of the town of Villaba. 5. Natural gas from some deep wells in Tertiary shale formations on the eastern flank of the Cordillera and extending out under the plain on the island of Panay. The first mention in geological literature, to the writer&apos;s knowledge, of gas or petroleum in the Philippines is found in the description of the Island of Panay by the Spanish geologist, Abella, in the year 1890. In 1898, an oil well was being dug on the estate of Smith Bell & Co., an English concern, near the town of Toledo on the west coast of Cebu. In

Jan 1, 1921

Jan 1, 1943

By Douglas W. Fuerstenau, Kalanadh V. S. Sastry

A mathematical model is developed for flotation in a countercur-rent column where continuously generated air bubbles rise through a downward flowing pulp. The model is based on the assumption of axially dispressed plug flow of both the liquid and air-bubble phases. An appropriate flotation-rate expression, which takes into account the changing concentration of solid particles on the bubble surface, is formulated and applied to the column flotation process. Although a complete solution of the resulting equations is not possible for the general case, solutions for specific limiting cases have been obtained. From these, it is possible to predict theoretically the dependence of the column performance on certain variables. Specifically, concentration profiles as a function of height in the column have been calculated for various values of the characteristic dimensionless parameters. The effect of axial dispersion on the perforance of the equipment is pointed out. In recent years, there has been considerable progress in delineating the fundamental physicochemical principles underlying the unit operation of flotation and in advancing methods for kinetic analysis and process modeling of flotation.&apos; In general, nearly all such process research has been concerned with the analysis of conventional flotation equipment and circuits. From these investigations, the possibility of developing and designing flotation apparatus for more efficient separation appears limited with conventional equipment. How- ever, recently there has been an attempt to apply coun-tercurrent flow techniques to flotation in the context of a flotation column.- some of the results from pilot-plant studies2 indicate possibilities for success of this process at least in obtaining higher-grade concentrates though not higher recoveries. A flotation column operates on countercurrent principle in which bubbles continuously generated at the bottom of the column rise through the downward flowing slurry. A schematic diagram of the flotation column is shown in Fig. 1. The physicochemical principles of bubble-mineral attachment, using this flotation column, are essentially the same as those which prevail in conventional equipment, the only differences being in the flow patterns of the various phases. The salient operating feature of the column as compared to those of a conventional cell is that neither mechanical nor turbulent pneumatic agitation is employed. The column is

Jan 1, 1971

By H. E. McCoy, C. J. McHargue

Single crystals of columbium containing various levels of oxygen, nitrogen, carbon, or hydrogen were deformed by slaw compression and impact loading at -196°C. For the slow deformation rates. 1500 to 1900ppm oxygen, 500 pprn nitrogen, or 150 to 200 ppm carbon completely suppressed mechanical twinning. Hydrogen in concentrations to 1000 ppm had no apparent effect on ease of twinning. Impact loading caused twins to form at all levels of contamination studied, and cleavage mucking on (100) planes occurred in specimens having higher interstitial contents. It is well established that, under some conditions, the bcc metals vanadium, columbium, tantalum, chromium, molybdenum, tungsten, and iron deform by formation of mechanical twins. In general it has been accepted that high strain rates, low temperatures, and large grain sizes are conducive to this kind of deformation.&apos; Since interstitial impurity atoms have a relatively large effect on slip in bcc metals, one might sus- pect a similar effect on twinning. This could occur directly by the interstitials affecting the nucleation or growth of the twins or indirectly from their effect on slip. It has often been argued that the large increase in yield stress caused by interstitial elements enables the effective stress to exceed that necessary to cause twinning. The twinning stress has always been thought to be higher than the stress necessary to cause slip in pure metals.2 simonsens and Tipper and Hall4 found profuse twinning in very pure a iron even at room temperature, whereas Low and Fueste15 and Churchman and tottrell&apos; observed twins in a iron containing carbon but none in highly decarburized specimens. McHargue7 reported mechanical twins to form readily in vanadium which contained 390 ppm interstitigs, while Clough and Pavlovic8 found twins only in the one or two grains adjacent to the fracture surface in vanadium which contained 1500 to 1700 ppm interstitials. In columbium, McHargue9 found high-purity single crystals to twin easily whereas Churchman,10 Adams, Roberts, and mallman,11 and Johnson12 studied less pure material and found far fewer twins. Although the results of Leadbetter and Argent13 showed oxygen to inhibit twinning, a study by sheely14 indicated the opposite to be true. Chromium exhibits this mode of deformation15,16 but there are no data regarding impurity effects. Lawley, Van den Sype, and Maddin17 observed twins in very pure molybdenum single crystals deformed at 77°K but none in less pure crystals. The work by Cahn18 and

Jan 1, 1963

By Marcel Daly

IN a preceding paper 1 the writer has pointed out some apparent relationship between the distribution, on the Surface of the globe, of the known hydrocarbon deposits and the disposition of the principal zones of deformation of the earth&apos;s body (geosynclines). He wishes to present some further remarks on this subject. Petroleum deposits, or their derivatives or descendants, are found through the whole range of sedimentary strata, from the pre-Cambrian to the Quaternary. For instance, the pre-Beltian (Shuswap) series of the Canadian Cordillera are interbedded with limestones which are sometimes rich in carbonaceous matter (Sicamous limestone) ; and the Beltian system of the same region contains layers of argillites and dolomitic limestones which are equally high in carbon content.2 This carbon may be interpreted as the last remnant of hydrocarbons previously contained in the rocks. On the other hand, the actual formation of hydrocarbons wider conditions that would eventually permit their deposition in modern sediments is conceded by some geologists.3 Between these two extreme limits, bitumens are found indifferently in all sedimentaries. They constitute a continuous series, some kind of a large family, whose individual members may be entitled to a community of origin and probably represent the differentt stages of evolution of the primitive, parent matter. . The kinship between petroleum and such substances as asphalt, ozocerite, manjak, grahamite, albertite, etc., is well known; and E. H. Cunninggam-Craig has recently shown how intimately shale fields and oil fields are connected. For this reason, no distinction is made in the present

Jan 8, 1917

By W. B. Plank

Those interested in training engineers for the mineral industry should consider how their men may fit into the general industrial recovery that now seems well started. One hears occasionally that too many engineers have been produced, especially mining engineers, and that the opportunities for their employment are decreasing. Just what is the situation? Enrollment in American engineering schools has fallen off sharply during the past few years. In 1930-31, the year of peak enrollment in all engineering schools, there were 78,685 engineering students in the United States, but in 1932-33 only 67,584, a decrease of 14 per cent. President Walters, of the University of Cincinnati, in his survey of 74 engineering schools, published in School and Society of Dec. 16, 1933, estimates that the engineering enrollment for 1933-34 is 10 per cent under that of 1932-33, or about 60,000. The situation in the mineral .ethnology schools somewhat parallels this general trend, although not to the same degree. Last year there were 4443 students in mineral technology schools, compared with 4687 in 1930-31, a decrease of 5 per cent. This year, with 3995 students, the enrollment shows a decrease of 10 per cent from last year, or a decrease of 15 per cent from 1930-31. Enrollment has no doubt been influenced by the condition of the mincral industry, just as the enrollment of other engineers has been affected by general industrial conditions. But the mineral industry, which is the first to recover, has not been so seriously affected as have some of the manufacturing industries during the past four years. This is especially true of coal and gold mining, which have been increasing rapidly in their production during the past year and have given employment to more men. Ten years ago, approximately 1,000,000 men were employed in the coal and metal mines and quarries, compared with probably half that number now. The number of mining engineering graduates in 1934 will be 234 and in metallurgy 252. In other words, fewer than 500 graduates are entering these industries the present year. With conditions improving in the mineral industry, coupled with a falling enrollment in our mining schools, there certainly exists an opportunity for young men now beginning their training for this industry.

Jan 1, 1934

IN describing the mining and treatment of ore at the Broken Hill Proprietary mine E. J. Horwood, superintendent of mines, gave the following account of the development of flotation there. It was in 1902 that the recovery of zinc from the ore by flotation was hit upon. The former general man-ager, Mr. Delprat, directed our then research officer, Mr. Carmichael, to try boiling the tailing with salt cake of which there was a considerable tonnage left over from the leaching process. The idea was the possibility of dissolving the zinc. Carmichael made the. Experi-ment, but, rather discouraged, took the glass beaker down to the general manager&apos;s office, remarking that he could not get the stuff to settle. On showing the beaker to Mr. Delprat, the latter recognized the marked distinction between the black scum on the surface and the rest of the tailings, and exclaimed: "Why, this is the very thing we are after; the zinc is floating!" Patents were applied for at once, but later on it was found that another investigator, Potter, had already hit upon the idea of flotation. His patents, however, were so involved with other operations that his process was impracticable. Litigation followed, but in the end the B. H. P. paid the Potter Company a substantial sum as settlement. In the case of Carmichael&apos;s beaker, the acid in the salt cake acted on the small amount of carbonate present in the ore, producing CO. bubbles. Owing to the aversion of sulfide crystals to being wetted, the gas as generated attached itself to the zinc in in-creasing quantities until there was sufficient to buoy the zinc particle to the surface. This action went The next problem was to apply the principle on a commercial scale, and this involved much experiment and developmental work. Various kinds of sloping copper pans with gas jets below to maintain the tem-perature were first tried, but were found too slow and too costly in operation.

Jan 6, 1928

By Wallace E. Pratt

IRon-oRe deposits in the Philippine Islands became the subject of official record as early as 1664. Undoubtedly iron ore was known and recognized by the Filipinos long before the earliest Spanish records. It is even possible that the Filipino practice of smelting iron ore is, like the native copper smelting, older than the Spanish conquest of the islands. The first records have to do with the magnetite-hematite ores near the towns of Santa Inez and Bosoboso in Rizal Province, from 15 to 20 miles east of Manila. The magnetite-hematite ores of Bulacan were exploited in 1783. Similar ores near the town of Mambulao in Camarines Province yielded a number of specimens to be exhibited in Spain in 1834. With the exception, then, of the lateritic iron ores on the eastern coast of northern Surigao, the true nature of which was not recognized until 1914, the important iron-ore deposits of the Philippines had all been discovered before the islands came under the dominion of the United States. Indeed, in the Spanish documents relating to the history of iron mining are statements which, if their accuracy be not questioned, leave us in the Philippines today with much less iron ore than the Spaniards found. To quote, for example, a report submitted to the Superior Government in Spain in 1835 by one of its emissaries, Don Lorenzo Calvo: "The Philippine Islands, most excellent Sir, possess iron and exhibit it in nearly every known mineralogical combination, and in such abundance that the cordillera of the island of Luzon, from Montufar Point in San Bernardino Straits to Cape Bojeador, is composed of no other mineral than iron, its ranges, of the third order, being in content and structure totally iron of the best quality, the more valuable in that its combinations are such as to facilitate its fusion and to render its redaction to metal simple." Today, however, it is recognized that the iron-ore deposits in the Eastern Cordillera of Luzon constitute, not a continuous belt, but a series of widely separated deposits, including a half dozen orebodies within a distance of 10 miles in Bulacan Province, a single outcrop at Santa Inez, Rizal Province, farther south, and three deposits around

Jan 1, 1916

By H. G. Moulton

The increasing scale of mining operations over the past decade, particularly in connection with the exploitation of large bodies of comparatively low-grade copper ores, has made necessary the study of the behavior of rock under failure. When extractions of as high as 40,000 tons a day are reached in steam-shovel operations and as high as 20,000 tons per day in underground mining operations, it is evident that excavations soon become of such size that the behavior of the rock will often be dependent on fundamental principles applicable to more or less homogeneous materials under stress, rather than on weathering or local planes of weakness. In the ordinary rock excavations encountered in civil-engineering practice, such as excavations for subways, highways, railroads, etc., rock faces are not carried to depths sufficient to develop any pressures, or consequently any failures, except those due to loose masses resulting from local planes of weakness. When, however, orebodies whose tonnage is measured by hundreds of thousands are to be extracted by steam-shovel operations in open pits, it is necessary to determine if possible in advance the slopes that the sides of the pits will assume, for these slopes influence the shape of the excavations and thereby the amount of ore that may be extracted by the open-pit method. When large orebodies are mined underground at depths of 300 to 500 ft. (91 to 152 m.) by caving methods, the surface subsiding as the ore is withdrawn, it is necessary to determine in advance the outermost limits of fracture in the subsiding surface, for on the delineation of these limits depends the location of surface improvements, mills, smelters, etc. and also the location of development work, such as hoisting shafts, main haulage levels, and all other underground openings that must remain undisturbed during the period of ore extraction. Heretofore, in civil-engineering practice, it has been assumed that earth and rock behave differently in failure. For the calculation of earth pressures, formulas are used in which the assumption is made that earth banks fail by sliding along the slope determined by the frictional resistance of the material. The line of failure and the resulting pressure is held to be dependent on the angle of repose, which is different for varying

Jan 1, 1920

By E. O. Bennett

When oil is takcn from a subsurface structure it is generally accompanied by gas. The gas thus produced represents the 1ighter hydrocarbons present in the original petroleurn accurnulation, which arc, insoluble at the reduced pressures created around a well when it is producing. In some cases the gas accompanying the oil may come from a gas-bearing stratum not in immediate contact with the oil. The amount of gas from the formation accompanying each barrel of oil is called the natural gas factor. Energy Causing Well to Flow The force causing the flow of fluid into a well when it is drilled into an oil-bearing structure is the pressure differential between the well bore and the formation. A pressure differential between the formation and the well may be set up in three different ways, as follows: (1) pressure due to gas in solution or in contact with the oil, (2) hydrostatic pressure due to water in contact with the oil (it may be either bottom or edge water); (3) pressure difference due to forcc of gravity. The greatest source of energy for producing oil from most oil fields, and the one over which the greatest control can be exerted, is the poten-tial energy in the gas under pressure in the formation. In any pool there is but a definite amount of gas available. Part of this gas may be in solution and a part in contact with oil. The amount of gas in solution in each bard of oil depends on the pressure and temperature in the formation and the characteristics of the oil. Whether the gas is in solution or in contact with the oil it is necessary to use the energy it, contains as efficiently as possible in order to obtain the greatest ultimate recovery from the pool. Bush1 states: Gas being the most efficient aid in moving the oil, it is important to prevent more of it from escaping than is necessary to remove the maximum amount of oil from the sands. The conservation of this energy is far more important to the producer of oil than his returns from sales of gas to distributing companies. The flowing life of the well is the most profitable period, and keeping the gas-oil ratio low, or keeping the

Jan 1, 1928

By Francis B. Foley

From the point of view of the metallographist, the adaptation of x-rays to the study of the crystal structure of metals is of the greatest importance. While one may hardly consider the findings resulting from x-ray study as revolutionary, their positive nature, compared with the deductions we have been forced to accept from the work that had gone before, gives firmer ground on which to build and furnishes new fields for speculation. Prior to the advent of the crystallogram, the best work on the crystal structure of steel was that of Osmond and Cartaud.&apos; They concluded, from their investigation with percussion figures formed at various temperatures, that alpha, beta, and gamma irons belonged to the cubic system and that they showed well-marked specific characteristics and could not have the same internal structure. What the internal structures were, they had no direct method of determining; but from a consideration of the fact that the 001 plane (that parallel to the cube face) is a plane of perfect cleavage and minimum hardness in alpha iron and that the 111 (octahedral) plane is by far the most important in the crystallography of gamma iron, they were led to suggest the simple cubic arrangement as that of alpha and the face-centered cubic arrangement as that of gamma iron. They suggested the body-centered cubic arrangement as that of beta iron. The atomic arrangement of the various crystal forms of iron has been quite definitely determined in recent years by means of x-rays and the work of Westgren2 and Weatgren and Phragmen3 has been rather conclusive. They not only determined the atomic arrangement of alpha, beta, and gamma iron but also that of the high-temperature modification delta.

Jan 1, 1926

By J. M. Uys, T. B. King

The solubility of water in silicate melts of various compositions was measured. The basicity of the silicate did not appreciably affect the water solu-bulity at low-base content (acid compositions). Near the orthosilicate composition the solubility increased with basicity for silicates in which the cation displayed a weak ion-oxygen attraction and apparently decreased for those in which the cation showed a strong ion-oxygen attraction; metasilicates of the former class dissolved more water than those of the latter. Temperature had little effect on water solubility. The experimental results are interpreted on the basis of two modes of solution, the contribution of one decreasing, and that of the other increas -ing, with increased melt basicity. In the former, solution occurs through interaction with doubly-bonded oxygen atoms and in the latter, through interaction with singly-bonded oxygen atoms, or, in very basic melts, through reaction with free oxygen ions. THE hydrogen content of a steel melt is in a large measure determined by water dissolved in the slag. In some glasses water may be a major cause of "seeds". Water vapor in the furnace atmosphere is the primary source in both instances. A knowledge of the mechanism of water solution in silicate melts should help in assessment of practical methods for its control in steelmaking and glass refining. Walsh et a1.l measured the water content, expressed as hydrogen, of 40 pct lime-20 pct alumina-40 pct silica and 62 pct manganese oxide-38 pct silica melts as a function of the steam partial pressure, in equilibrium with the melt. Tomlinson 2 and, also, Russell3 investigated this relationship for a molten 30 pct soda-70 pct silica glass. In all three investigations, the solubility of water was found to be proportional to the square root of the partial pressure of steam. Moulson and Roberts 4 confirmed this relationship for a silica glass. On the basis of the square root relationship, Tomlinson2 and Russell3 interpreted the solution reaction as "network-breaking", similar to that expected on the addition of metal oxides to silica. Walsh et al.&apos; postulated two possible modes of solution, one the mechanism suggested by Tomlinson and Russell and the other the reaction of the water molecule with an oxygen ion to form hydroxyl ions. These two modes of solution suggest opposite effects of melt basicity on water solubility. However, little appears to be known about the effect of melt basicity on water solubility. Walsh et a1.l found, in the lime-silica system, that the water content increased slightly with increased basicity. As these authors pointed out, this does not appear to be in accord with their further observation that slags containing little or no silica dissolve very little water. Kurkjian and Russell5 measured the effect of basicity on water solubility in alkali silicates in the composition range 15 to 45 mole pct alkali oxide. They found a minimum in the water content at about 25 mole pct alkali. This was interpreted on the basis of two concurrent solution reacZions; one in which solubility was proportional to the activity of doubly-bonded oxygen and, in the other, proportional to the activity of singly-bonded oxygen. The present work was aimed at establishing the effect of basicity on water solubility in silicate melts over as wide a range of compositions as practical. APPARATUS AND EXPERIMENTAL PROCEDURE The silicate melt was equilibrated with a "carrier-gas" of accurately known water content, quenched, and analyzed for water by a vacuum fusion technique. Some pertinent details of the equilibration procedure, analysis technique, preparation, and handling of the silicates are given below. Gas-Silicate Equilibration. The apparatus used to equilibrate the melt with the gas mixture was similar to that used by Walsh et al.&apos; but with some important modifications.6 Purification trains were provided for nitrogen and hydrogen; whenever air or oxygen was used as carrier gas the nitrogen purifiCation train was used with the copper furnace at room temperature. Gas flow rates were measured with capillary flow meters; bleeders filled with a mixture of dibromo and tribromo ethyl benzene (density about 2 g per cc) were used for convenience in controlling flow rates.

Jan 1, 1963

By William Kelly

An extensive swamp covers a large part of the town-site of Norway and adjacent laud. Through this swamp run two parallel oreformations. In the north one is the Aragon mine. The south one passes into the swamp on the Harrison property. On the edge of the swamp, about 1000 feet from the Aragon mine, a diamond drill, in the fall of 1889, located the ore-bearing formation and a probable ore-body. To explore further and develop this ore, the Penn Iron Mining Company proposed, in the spring of 1890, to sink a shaft. The drill had shown the depth of the glacial drift to be more than 60 feet. A test-pit near the location of the proposed shaft had struck, at a depth of 20 feet, an amount of water which a 200gallon pump was unable to lower. At the Aragon, a few years before, a shaft had been sunk to hard pan with great difficulty and many delays by the usual method of driving laths. Under the conditions it was decided to sink a caisson- or dropshaft. Two 40-horse-power boilers, a Lidgerwood engine with 4foot drum, and a good derrick were set up; and two No. 10 Kuowles

Jan 1, 1892